-
Publications No.
Issue DateINSTALLATIONINSTRUCTIONS
Accessory Application
2012 American Honda Motor Co., Inc. All Rights Reserved. AII
47334 (1208) 1 of 2908E92-T2A-1A00-90
AII 13039REMOTE CONTROL ENGINE STARTER
2013 ACCORD2 AND 4-DOOR
AUG 2012
PARTS LISTRemote Engine Starter Unit KitP/N 08E91-E54-100
Transmitter
Control unit
Antenna
ID label
Remote Control Engine Starter Attachment KitP/N
08E92-T2A-100A
(With Keyless Access System)
Engine starter harness
Control unit bracket
3 Relays
Flange nut
18 Wire ties
Wire tie with clip
6 Urethane tapes
Clip
Caution label
Fuse label
-
2 of 29 AII 47334 (1208) 2012 American Honda Motor Co., Inc. All
Rights Reserved.
Accessory Users Information Manual
Quick Start Guide
Remote Control Engine Starter Attachment KitP/N
08E92-T2A-100B
(Without Keyless Access System)
Engine starter harness
Control unit bracket
3 Relays
Flange nut
18 Wire ties
Wire tie with clip
6 Urethane tapes
Clip
Caution label
Fuse label
Accessory Users Information Manual
Quick Start Guide
-
2012 American Honda Motor Co., Inc. All Rights Reserved. AII
47334 (1208) 3 of 29
TOOLS AND SUPPLIES REQUIRED
Flat-tip screwdriverPhillips screwdriverRatchet10 mm Socket10 mm
Open end wrenchIsopropyl alcoholShop towelTape
measureScissorsHDS/MVCIMasking tapeDiagonal cuttersRulerTapeUtility
knifeThe following tools are available through the Honda Tool and
Equipment Program. On the iN, click on: Service > Service Bay
> Tool and Equipment Program, then enter the number under
Search. Or, call 888-424-6857. Trim Tool Set (T/N SOJATP2014)
Plastic Trim Tool (T/N SILTRIMTL10)
Illustration of the Remote Control Engine Starter in the
Vehicle
QB20940AH
ANTENNA
3 RELAYS
3A, 20A or 40A FUSES
CONTROL UNIT
ENGINE STARTER HARNESS
INSTALLATION
1. Disconnect the negative cable from the battery.
2. Attach the ID label.
Using isopropyl alcohol on a shop towel, clean the area where
the ID label will attach.
Attach the ID label to the transmitter in the area as shown.
With Keyless Memory SettingsNOTE: The remote is factory set for
driver 1 remote control. To program the driver 2 remote, follow the
REMOTE CONTROL ENGINE STARTER TRANSMITTER REGISTRATION instructions
on ISIS.
Customer Information: The information in this installation
instruction is intended for use only by skilled technicians who
have the proper tools, equipment, and training to correctly and
safely add equipment to your vehicle. These procedures should not
be attempted by do-it-yourselfers.
QB20939DH
ID LABEL
TRANSMITTER
Clean with isopropyl alcohol.
-
4 of 29 AII 47334 (1208) 2012 American Honda Motor Co., Inc. All
Rights Reserved.
Without Keyless Memory Settings
QB32111CH
ID LABEL
TRANSMITTER
Clean with isopropyl alcohol.
3. If equipped, remove the roof console. Using a plastic trim
tool, pry out and remove the
left and right lenses (four retaining tabs each). Open the
sunglass holder. Remove four screws. Remove the roof console
(unplug the vehicle
connectors).
With Moonroof
QB20901BX
VEHICLE CONNECTORS
ROOF CONSOLE
4 SCREWS
4 RETAINING TABS
LEFT LENS
SUNGLASS HOLDER(Open.)
4 RETAINING TABS
RIGHT LENS
-
2012 American Honda Motor Co., Inc. All Rights Reserved. AII
47334 (1208) 5 of 29
Without Moonroof
4. Remove two sunvisor holders by rotating them 90
counterclockwise.
QB20902AX
VEHICLE CONNECTORS
ROOF CONSOLE(if equipped)
4 SCREWS
4 RETAINING TABS
LEFT LENS
SUNGLASS HOLDER(Open.)
4 RETAINING TABS
RIGHT LENS
QB20903AX
PASSENGERS SUNVISOR HOLDER(Rotate.)DRIVERS
SUNVISOR HOLDER(Rotate.)
5. Wrap the end of a flat-tip screwdriver with tape. Locate the
slot in the bracket cover, and insert the flat-tip screwdriver into
the slot. Push the hook with the screwdriver.
6. While pushing in on the hook, rotate the drivers sunvisor
backward about 45. Make sure the hook slides into the bracket
cover.NOTE: If the hook did not stay pushed in, return the drivers
sunvisor to its original position and repeat steps 5 and 6.
QB32101AX
DRIVERS SUNVISOR
FLAT-TIP SCREWDRIVER
TAPE
BRACKET COVER
Push the hook.
HOOK
While pushing in on the hook, rotate the sunvisor backward about
45.
Make sure the hook slides into the bracket cover.
FRONT
-
6 of 29 AII 47334 (1208) 2012 American Honda Motor Co., Inc. All
Rights Reserved.
7. Remove the drivers sunvisor (unplug the vehicle
connector).
8. Pull away the drivers door opening seal in the area
shown.
9. Pull out on the drivers A-pillar trim to release the
clips.
QB20904AX
DRIVERS SUNVISOR
FRONT
VEHICLE CONNECTOR
QB20905AX2 CLIPS
DRIVERS A-PILLAR TRIM
DOOR OPENING SEAL (Pull away.)
Pull the clip.
10. Insert a shop towel in the opening between the drivers
A-pillar trim and the dashboard to prevent dropping the A-pillar
clips. Take care not to damage the drivers A-pillar trim.
11. Slide up the drivers A-pillar trim to remove it from the
upper clip. Carefully remove the shop towel and any clips that fell
from the drivers A-pillar trim.NOTE: The upper clip will stay in
the body.
QB20906AXSHOP TOWEL
DRIVERS A-PILLAR
DRIVERS A-PILLAR TRIM
QB20907AX
DRIVERS A-PILLAR TRIM
UPPER CLIP
-
2012 American Honda Motor Co., Inc. All Rights Reserved. AII
47334 (1208) 7 of 29
12. Remove the remaining upper clip from the drivers
A-pillar.
13. Install the new clip (supplied) to the drivers A-pillar
trim, but do not reinstall the trim at this time.
QB20908AX
UPPER CLIP(Discard.)
2 TABS (Push.)
DRIVERS A-PILLAR
Q0N0533AH
DRIVERS A-PILLAR TRIM
CLIP(supplied)
14. If equipped, remove the drivers dashboard under cover (turn
the knob and two clips).
15. Remove the drivers dashboard lower cover (nine clips and
unplug the vehicle connectors, if equipped).
QB20201AB
2 CLIPS
DRIVERS DASHBOARD UNDER COVER(if equipped) KNOB
(Turn.)
QB20202BB
DRIVERS DASHBOARD LOWER COVER
9 CLIPSVEHICLE CONNECTORS(if equipped)
-
8 of 29 AII 47334 (1208) 2012 American Honda Motor Co., Inc. All
Rights Reserved.
16. Remove the cover (six retaining tabs). Using the ignition
key, unlock the trunk lid/fuel fill door opener, then remove the
key.
17. Remove one self-tapping screw from the trunk lid/fuel fill
door opener cover.
QB32110AH
COVER
6 RETAINING TABS
TRUNK LID/FUEL FILL DOOR OPENER
Unlock.
KEY
SELF-TAPPING SCREW
DRIVERS DOOR SILL TRIM
18. Remove the drivers door sill trim.
4-Door: Two retaining tabs and four clips.
2-Door: Two retaining tabs and six clips.
QB20804AB
4 CLIPS
2 RETAINING TABS
DRIVERS DOOR SILL TRIM
QB32112AH
6 CLIPS
DRIVERS DOOR SILL TRIM
2 RETAINING TABS
-
2012 American Honda Motor Co., Inc. All Rights Reserved. AII
47334 (1208) 9 of 29
19. Pull away the door opening seal, and remove the drivers kick
panel (two clips).
20. Lower the tilt lever, and release the column band (two
clips). If the vehicle is equipped with keyless access system,
reconnect the negative cable to the battery, then press the engine
start/stop button to select the ON mode.
QB20805AB
2 CLIPS
DRIVERS KICK PANEL
DOOR OPENING SEAL (Pull away.)
QB32113AH
STEERING WHEEL
STEERING WHEEL
UPPER COLUMN COVER
COLUMN BAND
2 CLIPS
21. Turn the steering wheel 90 clockwise. Using a plastic trim
tool, release the retaining tab.
22. Turn the steering wheel 180 counterclockwise. Using a
plastic trim tool, release the retaining tab.
QB32114AH
UPPER COLUMN COVER
PLASTIC TRIM TOOL
STEERING WHEEL RETAINING TAB
QB32115AH
PLASTIC TRIM TOOL
RETAINING TAB
UPPER COLUMN COVER
STEERING WHEEL
-
10 of 29 AII 47334 (1208) 2012 American Honda Motor Co., Inc.
All Rights Reserved.
23. Remove the upper column cover (two retaining tabs and two
hooks).
24. Remove one self-tapping screw from the lower column
cover.
QB32116AH
UPPER COLUMN COVER
2 RETAINING TABS
2 HOOKS
QB32117AHLOWER COLUMN COVER
STEERING WHEEL
SELF-TAPPING SCREW
25. Turn the steering wheel 180 clockwise, and remove the other
self-tapping screw from the lower column cover.
26. Remove the lower column cover (one self-tapping screw).
27. If the vehicle is equipped with keyless access system, press
the engine start/stop button to select the OFF mode. Disconnect the
negative cable from the battery.
QB32118AHLOWER COLUMN COVER
SELF-TAPPING SCREW
QB32119AHSELF-TAPPING SCREW
LOWER COLUMN COVER
-
2012 American Honda Motor Co., Inc. All Rights Reserved. AII
47334 (1208) 11 of 29
Installing the Antenna
28. Using scissors, cut one urethane tape in half. Wrap two
halves of urethane tape to the antenna cable as shown.
QB62501BK
ANTENNA
60 mm (2.4 in.)
60 mm (2.4 in.)
HALVES OF URETHANE TAPE(Do not fold the antenna cable.)
URETHANE TAPE(Cut in half.)
ANTENNA CABLE
29. Starting near the antenna end of the cable, wrap one
urethane tape around the antenna cable at the measurements
shown.
30. Using scissors, cut two urethane tapes in half. Wrap four
halves of urethane tape around the antenna cable at the
measurements shown.
QB20901CH
ANTENNA CABLE
URETHANE TAPE
ANTENNA
220 mm(8.7 in.)
560 mm(22.0 in.)
ANTENNA CABLE
HALVES OF URETHANE TAPE
2 URETHANE TAPES(Cut in half.)
-
12 of 29 AII 47334 (1208) 2012 American Honda Motor Co., Inc.
All Rights Reserved.
31. Attach the antenna. Attach masking tape to the windshield at
the
measurement shown.
With Camera Cover
Without Camera Cover
QB51403BH
CAMERA COVER
HEADLINER
10 mm (0.4 in.)
MASKING TAPE
QB51402BH
MASKING TAPE
50 mm (2.0 in.)
HEADLINER
Fold the adhesive backing of the antenna as shown.
Using isopropyl alcohol on a shop towel, clean the windshield
where the antenna will attach.
Attach the antenna with masking tape. Adjust the position of the
antenna so there is equal spacing on both sides.
QB51401CH
ANTENNA
ADHESIVE BACKING
QB51404CH
Clean with isopropyl alcohol.
ANTENNA
MASKING TAPE
HEADLINER
ANTENNA
Equal spacing on both sides.
-
2012 American Honda Motor Co., Inc. All Rights Reserved. AII
47334 (1208) 13 of 29
Carefully remove the adhesive backing from the antenna, and
attach the antenna to the windshield. Press and hold the antenna
firmly in place for 30 seconds.
Remove the masking tape.
32. Gently pull down the headliner, and tuck the antenna cable
under the headliner. Be careful not to crease the headliner.
QB51405CH
ADHESIVE BACKING(Remove.)
ANTENNA
MASKING TAPE (Remove.)
QB20904CH
HEADLINER
ANTENNA CABLE
ANTENNA
33. Route the antenna cable down the A-pillar as shown. Using
five wire ties, secure the antenna cable to the vehicle
harness.
34. Pull away the door opening seal. Route the antenna cable
down next to the dashboard, and tuck the antenna cable between the
drivers A-pillar and the dashboard. Reinstall the door opening
seal.
QB20905AH
ANTENNA CABLE
VEHICLE HARNESS
5 WIRE TIES
ANTENNA CABLE
VEHICLE HARNESS
VEHICLE FRAME
QB20906BH
ANTENNA CABLE
DASHBOARD
DOOR OPENING SEAL (Pull away)
DRIVERS A-PILLAR
-
14 of 29 AII 47334 (1208) 2012 American Honda Motor Co., Inc.
All Rights Reserved.
Routing the Engine Starter Harness
35. Using isopropyl alcohol on a shop towel, clean the areas
where the fuse labels will attach.
36. Attach two 20A fuse labels (with keyless access system) or
two 40A fuse labels (without keyless access system) and two 3A fuse
labels to the engine starter harness relay block.
37. Install three relays to the engine starter harness relay
blocks.
QB20907AH
Clean with isopropyl alcohol.
3A FUSE LABEL
20A or 40A FUSE LABEL
Clean with isopropyl alcohol.
3A FUSE LABEL
20A or 40A FUSE LABEL
ENGINE STARTER HARNESS RELAY BLOCK
QB20908AH
3 RELAYS
ENGINE STARTER HARNESS RELAY BLOCKS
38. Using scissors, cut one urethane tape to the measurements
shown. Wrap the cut urethane tape around the engine starter harness
5-pin connector.
QB20909AH
20 mm (0.8 in.)
ENGINE STARTER HARNESS
25 mm (1.0 in.)
URETHANE TAPE
ENGINE STARTER HARNESS 5-PIN CONNECTOR
VIEW FROM URETHANE SIDE
-
2012 American Honda Motor Co., Inc. All Rights Reserved. AII
47334 (1208) 15 of 29
39. Unplug the vehicle 5-pin connector from the fuse box. Plug
the engine starter harness 5-pin connector into the fuse box 5-pin
connector. Plug the vehicle 5-pin connector into the engine starter
harness 5-pin connector.
NOTICE: Make sure the engine starter harness 5-pin connector is
securely connected to the fuse box 5-pin connector. A loose
connection can cause the engine to stall.
QB20910CH
VEHICLE 5-PIN CONNECTOR
ENGINE STARTER HARNESS 5-PIN CONNECTORS
1
312
Plug.
Unplug.
Push.
Push.Pull.
Connector unlock Connector lock
2
VEHICLE 5-PIN CONNECTOR
FUSE BOX
40. Using two wire ties, secure the engine starter harness to
the vehicle harness.
41. Plug the engine starter harness 4-pin connector into the
fuse box.
QB20911AH
ENGINE STARTER HARNESS
VEHICLE HARNESS
2 WIRE TIES
QB20912AHENGINE STARTER HARNESS 4-PIN CONNECTOR
4-PIN CONNECTORFUSE BOX
-
16 of 29 AII 47334 (1208) 2012 American Honda Motor Co., Inc.
All Rights Reserved.
42. Route the engine starter harness as shown. Remove the tape
from the vehicle harness. Do not damage the vehicle harness.
43. Attach the engine starter harness 28-pin connector to the
vehicle connector.
QB20913CH
ENGINE STARTER HARNESS 28-PIN CONNECTORS
TAPE(Remove, if equipped.)
VEHICLE CONNECTORS
44. Unplug the vehicle 28-pin connector, and plug it into the
engine starter harness 28-pin connector. Plug the engine starter
harness 28-pin connector into the vehicle 28-pin connector.
QB20914BH
FUSE BOX
VEHICLE 28-PIN CONNECTOR
VEHICLE 28-PIN CONNECTOR
VEHICLE 28-PIN CONNECTOR
ENGINE STARTER HARNESS 28-PIN CONNECTOR
ENGINE STARTER HARNESS 28-PIN CONNECTOR
-
2012 American Honda Motor Co., Inc. All Rights Reserved. AII
47334 (1208) 17 of 29
With Keyless Access System
45. Remove the tape from the engine starter harness 2-pin
connector. Unplug the vehicle 2-pin connector, and plug it into the
engine starter harness 2-pin connector. Plug the engine starter
harness 2-pin connector into the vehicle 2-pin connector.
QB20915CHENGINE STARTER HARNESS 2-PIN CONNECTOR
VEHICLE 2-PIN CONNECTORS
VEHICLE 2-PIN CONNECTOR
FUSE BOX
ENGINE STARTER HARNESS 2-PIN CONNECTOR
If equipped, do not connect.
TAPE (Remove.)
Without drivers dashboard under cover
46. Using a utility knife, cut the dashboard insulator as shown.
Go to step 48.
With drivers dashboard under cover
47. Remove the cap from the vehicle bolt.
QB20916AHBRAKE PEDAL
DASHBOARD INSULATOR(Cut.)
SLIT
Cut.
QB20917AH
CAP
VEHICLE BOLT
-
18 of 29 AII 47334 (1208) 2012 American Honda Motor Co., Inc.
All Rights Reserved.
48. Using a utility knife, cut the dashboard insulator to the
measurements shown. Do not damage the vehicle panel.
49. Using isopropyl alcohol on a shop towel, clean the control
unit where the urethane tape will attach.
50. Using scissors, cut the urethane tape in half, then wrap the
urethane tape around the control unit.
QB20918AH
FUSE BOX
Cut.
VEHICLE BOLT
DASHBOARD INSULATOR
15 mm (0.6in.)
15 mm (0.6in.)
QB20919BH
URETHANE TAPE(Cut in half.)
CONTROL UNIT
URETHANE TAPE
Align.
Clean with isopropyl alcohol.
51. Plug the antenna cable connector and engine starter harness
28-pin connector into the control unit.
52. Install the control unit bracket to the control unit.
QB20920AH
CONTROL UNIT
ANTENNA CABLE CONNECTOR
ENGINE STARTER HARNESS 28-PIN CONNECTOR
QB20921AH
CONTROL UNIT
CONTROL UNIT BRACKET
-
2012 American Honda Motor Co., Inc. All Rights Reserved. AII
47334 (1208) 19 of 29
53. Secure the engine starter harness clip to the control
bracket.
54. Using two wire ties, secure the antenna cable to the engine
starter harness.
QB20922AH
CONTROL UNIT BRACKET
ENGINE STARTER HARNESS CLIP
CONTROL UNIT
QB20923AH
CONTROL UNIT BRACKET
ENGINE STARTER HARNESS
ANTENNA CABLE
2 WIRE TIES
55. Using one flange nut, secure the control unit bracket to the
vehicle panel as shown.
56. Secure the engine starter harness clip to the vehicle
bolt.
QB20924AH
CONTROL UNIT BRACKET
VEHICLE PANEL
FLANGE NUT
QB20925AH
ENGINE STARTER HARNESS CLIP
ENGINE STARTER HARNESS
CONTROL UNIT BRACKET
VEHICLE BOLT
-
20 of 29 AII 47334 (1208) 2012 American Honda Motor Co., Inc.
All Rights Reserved.
57. Using isopropyl alcohol on a shop towel, clean the control
unit bracket where the urethane tape will attach.
58. Using scissors, cut the urethane tape in half as shown, then
attach the urethane tape to the control unit bracket.
With drivers dashboard under cover
59. Reinstall the cap to the vehicle bolt.
QB20926AH
Clean with isopropyl alcohol.
URETHANE TAPE
Cut in step 50.
URETHANE TAPE (Cut.)
CONTROL UNIT BRACKET
QB20927AH
CONTROL UNIT BRACKET
CAP(reused)
VEHICLE BOLT
60. Attach the engine starter harness relay blocks to the
control unit bracket.
61. Remove the vehicle ground bolt.
62. Attach the engine starter harness ground terminal to the
vehicle ground terminal, and reinstall the vehicle ground bolt.
QB20928AH
CONTROL UNIT BRACKET
ENGINE STARTER HARNESS RELAY BLOCKS
CONTROL UNIT BRACKET
QB20929CH
ENGINE STARTER HARNESS GROUND TERMINAL
VEHICLE GROUND BOLT(reused)
VEHICLE GROUND TERMINAL
-
2012 American Honda Motor Co., Inc. All Rights Reserved. AII
47334 (1208) 21 of 29
63. Using one wire tie, secure the antenna cable and engine
starter harness to the vehicle harness.
64. Bundle up the excess antenna cable as shown. Using two wire
ties, secure the antenna cable and engine starter harness to the
vehicle harness.
QB20930CH
FUSE BOX
ENGINE STARTER HARNESS
ANTENNA CABLE
VEHICLE HARNESS
WIRE TIE
2-PIN CONNECTOR(if equipped)
QB20931DH
ENGINE STARTER HARNESS
ANTENNA CABLE(Bundle.)
VEHICLE HARNESS
2 WIRE TIES
20 mm (0.8 in.) or above.
65. Secure the engine starter harness to the hole in the vehicle
frame with one wire tie with clip at the white tape on the engine
starter harness.NOTE: If another accessory harness is already
attached, align the white tape on the engine starter harness with
the clip on the other harness. Using one wire tie with clip, secure
the engine starter harness to the other accessory harness.
QB20932AH
ENGINE STARTER HARNESS
WIRE TIE WITH CLIPWHITE TAPE
WHITE TAPE
OTHER ACCESSORY HARNESS CLIP
WIRE TIE WITH CLIP
WITH OTHER ACCESSORY HARNESS
-
22 of 29 AII 47334 (1208) 2012 American Honda Motor Co., Inc.
All Rights Reserved.
66. Route the 12-pin/10-pin connector ends of the engine starter
harness as shown.
67. Align the white tape on the engine starter harness with the
clip on the vehicle harness, and secure the engine starter harness
to the vehicle harness using one wire tie.
68. Using one wire tie, secure the engine starter harness to the
vehicle harness.
QB20933AH
VEHICLE HARNESS CLIP
WHITE TAPE
2 WIRE TIES
VEHICLE HARNESS
ENGINE STARTER HARNESS
Inside
69. Route the engine starter harness as shown. Unplug the
vehicle 10-pin connector, and plug it into the engine starter
harness 10-pin connector. Plug the remaining engine starter harness
10-pin connector into the wiper switch.
QB20934AH
ENGINE STARTER HARNESS
ENGINE STARTER HARNESS 10-PIN CONNECTOR
ENGINE STARTER HARNESS 10-PIN CONNECTOR
VEHICLE 10-PIN CONNECTOR
WIPER SWITCH
-
2012 American Honda Motor Co., Inc. All Rights Reserved. AII
47334 (1208) 23 of 29
70. Using one wire tie, secure the 10-pin connector and the
engine starter harness to the vehicle harness.
QB20935BH
IGNITION SWITCH
WIRE TIE
10-PIN CONNECTOR
ENGINE STARTER HARNESS
Do not undue strain to the 10-pin connector cord.
71. Route the engine starter harness as shown. Unplug the
vehicle 12-pin connector, and plug it into the engine starter
harness 12-pin connector. Plug the remaining engine starter harness
12-pin connector into the combination light switch.
QB20936AH
ENGINE STARTER HARNESS
ENGINE STARTER HARNESS 12-PIN CONNECTOR
ENGINE STARTER HARNESS 12-PIN CONNECTOR
VEHICLE 12-PIN CONNECTOR
COMBINATION LIGHT SWITCH
-
24 of 29 AII 47334 (1208) 2012 American Honda Motor Co., Inc.
All Rights Reserved.
72. Using three wire ties, secure the engine starter harness to
the vehicle harness. Do not secure it to the SRS harness.NOTE: Make
sure that the connectors and harness are not pinched, or are not
interfering with the steering wheel when it is moved for
adjustment.
QB20937BH
ENGINE STARTER HARNESS
2 WIRE TIES
VEHICLE HARNESS
WIRE TIE
Do not pull the 12-pin connector cord wire too tight.
73. Using isopropyl alcohol on a shop towel, clean the hood
where the caution label will attach.
74. Attach the caution label to the hood in the area shown.
75. Check that all wire harnesses are routed properly and all
connectors are plugged in.
76. Check the overlap between the headliner and the drivers
A-pillar trim. Refer to the Service Manual. If necessary, adjust
the overlap.
77. Reinstall all removed parts.78. Reconnect the negative cable
to the battery.79. Press and hold the radio power button for
two
seconds to restore the radio and navi (if equipped) system
functions.
80. Reset the clock.81. Perform the REMOTE ENGINE STARTER
REGISTRATION and the FUNCTION CHECK.
QB20938AH
Clean with isopropyl alcohol.
CAUTION LABEL
-
2012 American Honda Motor Co., Inc. All Rights Reserved. AII
47334 (1208) 25 of 29
REMOTE ENGINE STARTER REGISTRATION1. Acquire the PCM Code from
the Interactive Network.
2. Connect the HDS/MVCI tester to the OBD II data link
connector, then turn the ignition switch to the on (II)
position.
3. Start the HDS, and click the car icon.4. Input the VIN and
other required information into the
HDS, then click the check button.
5. Select Honda Systems, then click the check button.
QB40150AH
CAR ICON
QB32102BH
Input the VIN and other required information. CHECK BUTTON
6. Select R/C ENG STARTER and click the check button.
QB32103AH
Select Honda Systems.
CHECK BUTTON
QB32104AH
Select R/C ENG STARTER.
CHECK BUTTON
-
26 of 29 AII 47334 (1208) 2012 American Honda Motor Co., Inc.
All Rights Reserved.
7. Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT, then
click the check button.
8. The following message will display: Obtain PCM-code
(IMMOBILIZER PCM CODE) from iN. This vehicles VIN will be required
to obtain the password. (USA) Click the check button.
QB32105BH
Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT.
CHECK BUTTON
QB32106AH
Obtain PCM-code message.
CHECK BUTTON
9. Input the PCM-code, then click the check button.NOTE: To
ensure security, the PCM-code (password) is changed everyday, so it
is impossible to register the remote control engine starter if the
dates of the PCM-code acquisition and registration are different.
The date of the HDS/MVCI tester should also be the same.
10. The following message will display: The registration of the
Remote Control Engine Starter Unit has been completed. Turn the
ignition switch off.
QB32107BH
Input the PCM-Code.
CHECK BUTTON
-
2012 American Honda Motor Co., Inc. All Rights Reserved. AII
47334 (1208) 27 of 29
11. The following message will display: Check that engine can be
started by the Transmitter. Click the check button.
QB32108CH
The registration of the Remote Control Engine Starter Unit has
been completed.
-
28 of 29 AII 47334 (1208) 2012 American Honda Motor Co., Inc.
All Rights Reserved.
12. Perform the FUNCTION CHECK on page 28, then disconnect the
HDS/MVCI.
FUNCTION CHECK
Operating Conditions
The hood is closed The shift lever is in park Turn the ignition
switch off and the key is outside the vehicle All doors and trunk
lid closed and locked
Inspection
1. Press the engine/command button on the transmitter and
release, within 2 seconds, press the lock/start button on the
transmitter.The engine should start if all operating conditions are
met.
Does the engine start?
Yes - Operation is normal.
No:
Make sure all Operating Conditions are met.
Check the engine starter harness connections.
Connect the HDS/MVCI and check for an indicated
failure. (Refer to the appropriate Service Manual for
details.)
QB32109CH
Check that engine can be started by the Transmitter.
CHECK BUTTON
-
2012 American Honda Motor Co., Inc. All Rights Reserved. AII
47334 (1208) 29 of 29
2. Press the engine/command button on the transmitter and
release, within 2 seconds, press the unlock/stop button. The engine
should stop.
Does the engine stop?
3. After the engine has stopped, start the engine again, and
check that the engine stops after each of the following
conditions:
NOTE: After each test the ignition key must be cycled, or the
drivers door must be opened and closed.
Move the shift lever out of the P position. Unlock or open the
doors or the trunk lid. Open the hood. Insert the key in the
ignition. If the vehicle is equipped the keyless access system,
press the engine start/stop button. Press on the brake pedal.
Does the engine stop after each of these tests?
4. Check that the power windows and the moonroof do not
function, and the shift lever does not move to any position when
the engine is started with the transmitter.
5. If the vehicle is equipped with the keyless access system,
check that the engine does not start under Operating Conditions
with the key left inside the vehicle.
6. Start the engine again, press the engine/command button on
the transmitter two times, and check the vehicle condition on the
display.
7. Check the operation of the transmitter when the vehicle is
120 m (400 ft.) away and in direct sight.8. Press the unlock/stop
button on the transmitter and verify that the doors unlock. Press
the lock/start button, and
verify that the doors lock. For the vehicle equipped with the
memory seat, make sure to shift the seat position of drivers seat
to Driver 1
by unlock of transmitter.9. Check that the engine can start by
the vehicle key and that the wiper and the headlight can be
operated normally.
Yes - Operation is normal.
No - Check the engine starter harness connections.
Yes - Operation is normal.
No - Check the engine starter harness connections.
B127121H
ENGINE/COMMAND BUTTON
UNLOCK/STOP BUTTON
RECEPTION INDICATOR
CHECKING INDICATOR
ENGINE START OPERATION
Blinking
ENGINE RUNNING INDICATOR
IN-CAR TEMPERATURE*1
REMAINING IDLING TIME*1
*1 Only on vehicles equipped with the automatic climate
control.This indicator is displayed for some vehicles among
them.
LOCK/START BUTTON
Button9: