Installation Procedure: EVC-E2 D4/D6 Aquamatic & Inboard IMPORTANT! Never cut or modify the Volvo Penta EVC harnesses. For extra hower supply, use the Volvo Penta relay for external accessories. Use cable ties. To trim pump power supply DPH connections To POWER TRIM CONN To trim potentiometer Gear FWD Gear REV Connect shift cable. Lock cable with cotter pin. Power up before connecting shift cable to secure neutral position of actuator. To GEARSHIFT CONN. Shift cable bending radius max. 200 mm (8”) Shift cable fitting down- wards. Cover upper slot with a decal Mount actuator on transom preferably, angled 5˚ downwards Connecting multiple Multilink hubs Docking station DPH twin, electronic steering Joystick Stand- alone HCU Multifunction panel (Docking station panel) Stand-alone HCU connections Buzzer 11 11 10 NMEA2000 backbone Female terminator Male terminator Chartplotter EVC Autopilot Compass (CCU) EVC Autopilot Battery 12 VDC T-connector Backbone ex- tension cable Fuse Power cable 23 20 20 20 20 Use AUX relay 24 20 22 24 Steering Control Unit (SCU) DPH twin, electronic steering Clamp steering hoses and cables To levers, standard EVC bus cable To engine, ex- tension cable IMPORTANT! The SCU can be mounted vertically or horizontally. Do NOT mount the SCU with hoses lead- ing up. This will trap air in the hydraulic valve body and cause erratic operation. Connect power to SCU Engine starting battery Main switch Fuse Tightening torque: 5 Nm (3.7 lbf.ft) 25 Multilink hub 2.5” display Lever connections Lever Buzzer Connection for safety lanyard Rudder angle sender Fresh water and fuel level send- ers Engine Typical installation Single engine, inboard 12 10 10 e-Key panel 7 AUX bus termination 7 7 7 7 7 7 2 5 Example: Twin installation with (left) and without (right) accessories connected on the AUX bus Correct! Termination in the beginning and at the end of the AUX bus Termination plug There is no need of termination plugs if nothing is connected on the AUX bus. 7 Joystick Steering wheel Levers Lever connections Buzzer Actuator Powertrim pump Connection for safety lanyard Steering Control Unit Rudder angle sender (not used) Fresh water and fuel level senders Engine Engine 7 12 5 2 11 10 8 7 Termination plug Multisensor Battery Compass (CCU) To NMEA2000 backbone Autopilot 4” display 7” display e-Key panel 11 8 12 31 31 25 Termination plug 5 7 7 1 1 8 Helm station Helm station To next helm station To next helm station Engine Engine IMPORTANT! This end of Y-connector must be connected directly, without extension, to levers/HCU. Y-connector Multiple helm stations 8 8 8 8 7 7 11 11 11 11 Buzzer Connection for safety lanyard Analog Key Analog key interface (optional) Typical installation / Main station DPH twin, electronic steering Joystick Steering wheel Multilink hub Multifunction panel (Start/Stop panel) 2.5” displays Levers Lever connections Buzzer Flybridge DPH twin, electronic steering 11 11 10 10 10 10 10 Autopilot 4” display To NMEA 2000 backbone 20 IMPORTANT! Maximum cable length between Multil- ink hub and unit (display etc.) is 3 m (10 ft). Maximum total cable length on Multilink is 20 m (66 ft). 20 20 10 10 9 Multilink hub Color coded cable Interceptor server unit Interceptor Control Module (ICM) Interceptor server unit 1 7 7 33 Multisensor Installation Procedure: EVC-E2 D4/D6 Aquamatic & Inboard Document number: 47704055 Release date: 05-2013 Display options Single Twin 2,5” display 2,5” display 4” display 4” display 7” display 7” display MIN MIN MIN MIN MIN MAX MAX MAX MAX MAX MAX
2
Embed
Installation Procedure: Installation Procedure: EVC-E2 D4 ...muldermotoren.com/SalesGuidedec2014/prosales.penta... · 32. e-Key extension cable, 12-pin Feet Meter Part no. 4.71.44
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
IMPORTANT! Never cut or modify the Volvo Penta EVC harnesses. For extra hower supply, use the Volvo Penta relay for external accessories. Use cable ties.
To trim pump power supply
DPH connections
To POWER TRIM CONN
To trim potentiometer
Gear FWD
Gear REV
Connect shift cable. Lock cable with cotter pin. Power up before connecting shift cable to secure neutral position of actuator.
To GEARSHIFT CONN.
Shift cable bending radius max. 200 mm (8”)
Shift cable fitting down-wards. Cover upper slot with a decal
Mount actuator on transom preferably, angled 5˚ downwards
Steering Control Unit (SCU)DPH twin, electronic steering
Clamp steering hoses and cables
To levers, standard EVC bus cable
To engine, ex-tension cable
IMPORTANT! The SCU can be mounted vertically or horizontally. Do NOT mount the SCU with hoses lead-ing up. This will trap air in the hydraulic valve body and cause erratic operation.
Connect power to SCU
Engine starting battery
Main switch
Fuse
Tightening torque: 5 Nm (3.7 lbf.ft)
25
Multilink hub
2.5” display
Lever connectionsLever
Buzzer
Connection for safety lanyard
Rudder angle sender
Fresh water and fuel level send-ers
Engine
Typical installationSingle engine, inboard
12
10
10
e-Key panel7
AUX bus termination
7 7 7 7
7
72
5
Example: Twin installation with (left) and without (right) accessories connected on the AUX bus
Correct!Termination in the beginning and at the end of the AUX bus
Termination plug
There is no need of termination plugs if nothing is connected on the AUX bus.
7
JoystickSteering wheel
Levers
Lever connections
Buzzer
Actuator Powertrim pump
Connection for safety lanyard
Steering Control Unit
Rudder angle sender (not used)
Fresh water and fuel level senders Engine Engine
7
12
5
2
11
10
8
7
Termination plug
MultisensorBattery
Compass (CCU)
To NMEA2000 backbone
Autopilot 4” display
7” display
e-Key panel
11
8
19
12
3131
25
Termination plug 5
7
7
11
8
Helm station
Helm station
To next helm station To next helm station
EngineEngine IMPORTANT! This end
of Y-connector must be connected directly, without extension, to levers/HCU.
Y-connector
Multiple helm stations 8
8
8
8
77
11 11
11 11
Buzzer
Connection for safety lanyard
Analog Key
Analog key interface (optional)
Typical installation / Main stationDPH twin, electronic steering
JoystickSteering wheel Multilink hub
Multifunction panel(Start/Stop panel)
2.5” displays
Levers
Lever connections
Buzzer
FlybridgeDPH twin, electronic steering
11 11
10
10
1010
10
Autopilot 4” display
To NMEA 2000 backbone
20
IMPORTANT! Maximum cable length between Multil-ink hub and unit (display etc.) is 3 m (10 ft). Maximum total cable length on Multilink is 20 m (66 ft).