7 7 7 7 7 Engine connections IPS 350/400/450/500/600 IPS 800/900 IPS 1050/1200 AUX BUS AUX BUS AUX BUS AUX BUS AUX BUS AUX BUS SENDERS DATALINK DATALINK DATALINK SENDERS SENDERS A B C ENGINE CONN. DIAGNOS Multilink minimum requirements: NOTE! Minimum two 2.5” displays or one 4” or 7” display. Maximum two 4” or 7” displays on one helm station. To next station To next station 10 Installation Procedure: EVC-E Volvo Penta IPS* Twin Installation Procedure: EVC-E Volvo Penta IPS Twin Document number: 47702213 Release date: 06-2012 Multilink hub Buzzer Connection for safety lanyard Rudder angle sender (not used) Fresh water and fuel level senders SUS Diagnose connection (VODIA) Connection locations Propulsion unit connections Steering Controls ACP – Active Corrosion Protection Docking station IMPORTANT! Never cut or modify the Volvo Penta EVC harnesses. For extra power supply, use the Volvo Penta relay for external accessories. IPS 350/400/ 450/500/600 Steering unit Joystick IPS 800/900/ 1050/1200 Oil temperature and pressure Oil temperature and pressure Datalink to SUS Datalink to SUS Reverse (SECONDARY) Reverse (SECONDARY) Forward (PRIMARY) Forward (PRIMARY) Rev. pickup Rev. pickup Use template when making holes in dashboard Use cable ties to fix cables Transom unit To transmission cable To AUX-bus connection To transom unit Tilt adjuster bracket Steering wheel hub Max. 15 mm (0.59”) dashboard thickness Connecting multiple Multilink hubs Joystick Stand- alone HCU Multifunction panel (Docking station panel) Stand-alone HCU connections Buzzer 11 11 10 Flybridge Joystick Steering wheel Multilink hub Buzzer Multifunction panel (Start/Stop panel) Dynamic Positioning System interface Dynamic Positioning System antenna 7” display Levers Lever connections 10 11 11 18 Typical installation / Main station IPS 350/400/450/500/600, IPS 800/900, IPS 1050/1200 OK! For information on cable lengths etc. please refer to Installation manual. NOT OK! OK! 1 2 3 4 5 Multisensor SUS CPM ACP Battery Control Unit (BCU) 2.5“ Battery Management display Battery sensor IMPORTANT! This end of Y-connector must be connected directly, without extension, to levers/HCU. Y-connector Multiple helm stations Helm station Helm station 8 8 7 8 8 Engine Engine 8 2.5” display 7” display 4” display Autopilot 4” display To NMEA2000 backbone B A C Compass (CCU) Joystick Steering wheel Levers Lever connections 11 11 11 5 7 9 10 19 10 12 11 9 2.5” display Multilink hub 10 10 16 16 Termination plug 21 21 Autopilot 4” display To NMEA2000 backbone 10 10 12 10 Termination plug 1 20 NMEA interface ADU 7 7 7 Battery Management Negative terminal Starter motor Remote frequency reciever with WLAN (RFW) Continuous output 20 A B: fused output A: unfused output House loads 2.5” Battery Management display Battery sensor To engine connector (AUX) To external switches (optional) Termination plug 25 7 AUX-bus termination Correct! Termination in the beginning and at the end of the AUX-bus Incorrect! No end termination of the AUX-bus Termination plug Termination plug D11 D11 10 5 5 Battery Control Unit (BCU) 20 20 5 NMEA2000 backbone Female terminator Male terminator Chartplotter EVC Autopilot Compass (CCU) EVC Autopilot Battery 12 VDC T-connector Backbone ex- tension cable Fuse Power cable 23 20 20 20 20 Use AUX relay 24 20 22 24 e-Key panel Battery sensor 10
2
Embed
Installation Procedure: EVC-E Volvo Penta IPS* Twinmuldermotoren.com/volvopentadvd/marine/orderspec/opt_eq/47702213.pdf · Volvo Penta EVC harnesses. For extra power supply, use the
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
7
7 7
7
7
Engine connections
IPS 350/400/450/500/600
IPS 800/900 IPS 1050/1200
AU
X BU
SA
UX B
US
AU
X BU
S
AUX BUS
AUX BUS AU
X BU
S
SEN
DER
S
DATA
LINK
DATALINK
DATA
LINK
SENDERS SEN
DER
S
A
B C
ENGINE CONN.
DIAGNOS
Multilink minimum requirements: NOTE! Minimum two 2.5” displays or one 4” or 7” display.Maximum two 4” or 7” displays on one helm station.
21. Battery sensor cable Feet Meter Part no.9.8 3 21840060
24. NMEA2000 Termination plugs Type Part no.Male 21812196** Female 21812203**
23. NMEA2000 Powercable Feet Meter Part no.6.6 2 21812205**
22. NMEA2000 T-connectorPart no.21812195**
**) Incl. in Autopilot kit
Cables
7. Standard EVC bus cable, 6-pin* Feet Meter Part no.5 1.5 21865234 16 5.0 874789 23 7.0 889550 30 9.0 889551 36 11.0 889552 42 13.0 888013*) One cable per engine has to be ordered.
8. Y-connector, 6-pinFeet Meter Part no.1.6 0.5 3588972
10. Multilink cable, 6-pinFeet Meter Part no.5 1.5 3886666