INSTALLATION MANUAL FOR RAM · INSTLLATION MANAUL FOR RAM Automatic power deploy: The running boards will extend down and out when the door is opened. Automatic stop: If an object

INSTALLATION MANUAL FOR RAM

INSTALLATION TIME (Hours）

0.5 1 2 3

Professional installation recommend

TOOLS

We highly recommend you to find professional store to install the product.

If not follow the instruction may damage the ECU, motor or the car.

Attention

Wrench tool

Plier

架

Rivet gun

tape

insulating

tape

Attention

Plastic crow plate

crow plate

INSTALLATION MANAUL FOR RAM

Plastic line x1 Wire harness: one set for motor

power and signal

Tie wire x20

Controller

Running boards x2

M6 Gasket x12 M8 Gasket x12

Screw package

M6*25 hexagon screw x12

U-Gasket x10

Drive bracket x2

M8 Nut x12

Driven bracket x4

M8*25 Flange Screw x24

Rear plate x2 Middle plate x2 Front plate x2

M10 rivet nut x4

INSTALLATION MANAUL FOR RAM

1.Installation of Controller,OBD &Wiring

1）Take out the fuse 2）Connecting positive pole with battery

5 ） Fixing the ECU

behind the brake pedal

4）The positive line from here to

cabin

wire to the engine room

6）Use screw to fix controller

Caution! Tighten battery screw very

tight! If loose, may get damage to the car.

INSTLLATION MANAUL FOR RAM

10 ） at driver side, find the CAN

connector, green connector one

11）insert with above green connector,

not the white one.

9）left and right motor line from here

to go inside the cabin. 7）negative connect as above 8）Open the carpet and find the hole

13) plug in all

connecor, use

tape to fix them.

Connect ECU,

insert fuse, then

test the motor

work well or

not.

12）the right side motor line from here

to right side to connect with motor

Car direction (Left side)

DODGE RAM 1500 INSTLLATION MANAUL

2.Install left connection base（Same way for right side）

Tighten all screws !

Left Front Plate Left Rear Plate 2

3

6 5 1

4

8

7 11

10 9

12

1.2.5.6.9.10 Use M8*25 flange screw and M8 nut to fix.

3.4.11.12 Use M8*25 flange screw to fix.

Middle Plate

7.8 use rivet gun and nut to fix.

Car direction (Left side)

INSTLLATION MANAUL FOR RAM

3.Install left brackets（Same way for right side）

KEEP ALL SCREWS A LITTLE LOOSE,

SO THAT BRACKET CAN MOVE WITH

RUNNING BOARD!!!

LF idler bracket

左前从动支架 LRear idler bracket

1

3

2

4

1.2.3.4 Use M8*25 screw to fix,the

same way for other bracket.

LM motor bracket

INSTLLATION MANAUL FOR RAM

4.Install left board (Same way for right side）

Use M6x25 screw and spring washers to fix running board with brackets.

TIGHTEN SCREWS TO FIX BOARD WITH BRAKCETS!

INSTLLATION MANAUL FOR RAM

5. Testing and adjust the balance

3

2 1

FASTEN ALL SCRWS (4x6=24) ON THE 6

BRACKETS

If still not balance, use U shape

washer to adjust it.

4

Insert fuse again. Then open and close doors to let step work.

To assure them up and down freely to adjust position by itself.

INSTLLATION MANAUL FOR RAM

6, Checking all doors activate, the side step work when doors open and close.

Now the installation is finished. Protect all connectors with tap to avoid loose.

To lift the car as

showed

To lift the car

INSTLLATION MANAUL FOR RAM

Automatic power deploy:

The running boards will extend down and out when the door is opened.

Automatic stop:

If an object is in the way of the moving running board, the running board will automatically stop. To reset, clear any obstruction, then

simply open and close the door to resume normal operation.

Manually set in the deployed (OUT) position for access to the roof:

Step your foot while at the same time closing the door. To resume normal operation, open and close the door.

Maintenance: In adverse conditions, debris such as mud, dirt, and salt may become trapped in the running board mechanism,

possibly leading to unwanted noise. If this occurs, manually set the running boards to avoid spraying the motors directly. After

washing, apply silicone spray lubricant to the hinge pivot pins.

Caution! Keep hands and feet away when the running board is in motion.

To changing tire