Installation Instructions - THI ECommerce...Installation Instructions For Part Numbers: 400-214-1 720-472 Airaid Oiled Media Filter 401-214-1 721-472 SynthaMax Dry Media Filter -Red

Installation Instructions For Part Numbers:

400-214-1 720-472 Airaid Oiled Media Filter

401-214-1 721-472 SynthaMax Dry Media Filter - Red

402-214-1 722-472 SynthaMax Dry Media Filter - Black

403-214-1 723-472 SynthaMax Dry Media Filter - Blue

2008 -10 Ford F-250 Thru F-550 Super Duty

6.4L V8 Power Stroke

Component Identification

1. Airaid Premium Filter 1

2. Airaid Cool Air Box 1

3. Top Panel 1

4. Filter Adapter 1

5. Weather Strip 33 1/4” 1

6. 1/4-20x5/8” Hex Bolt 4

7. ¼” Flat Washer 4

8. 1/4-20 Serrated Nut 1

9. 8-32x3/8” Button Head Bolt 8

10. #8 Flat Washer 6

11. Bracket 1

12. Adapter Gasket 1

13. 1/8” x 4” O - Ring 1

14. 8-32x1/2” Flat Head Screw 2

15. Calibration Plate 1

16. T20 Torx Security Bit 1

17. O-Ring Grease 1

1. Disconnect the negative battery cables. A) Loosen the hose clamp that holds the intake tube

to the airbox. B) Disconnect the filter minder wiring

harness, and then remove the factory filter minder and

grommet from the intake tube (save for reuse).

C) Disconnect the Mass Air Flow (MAF) sensor wir -

ing harness. Using the supplied Torx bit, remove the two

screws, and the (MAF) sensor from the factory airbox.

Save the MAF sensor for reinstallation in step #10.

3. Remove one bolt from the factory airbox mounting

plate, and save it for reinstallation in step #8.

6. Install the O-ring (#17) into the groove on the

Cool Air Box as shown. Apply a light coat of the

supplied grease onto the O-ring.

4. Install the adapter gasket (#12), and filter adapter

(#4) into the Airaid Cool Air Box (#2) using three

1/4-20x5/8” hex bolts (#6), and 1/4” flat washers

(#7).

7. Apply a light coat of the supplied grease onto the

inside of the factory tube. Install the Airaid Cool Air

Box into the vehicle making sure it is seated correct-

ly into the factory grommets, and the inlet is aligned

with the factory hole in the fender. Slide the factory

intake tube over the O-ring and then tighten the fac-

tory hose clamp.

9. A.) Install the Calibration Plate onto the Cool Air

Box using two 8-32 x 1/2” Flat Head Screws (#14).

B.) Reinstall the factory grommet, and filter minder

into the Cool Air Box, and then reconnect the filter

minder wiring harness.

2. Remove the factory airbox and tube from the vehi-

cle as an assembly, by pulling straight up on the box.

It is only held in place by grommets, no bolts.

5. Install the bracket (#11) using one 1/4-20x5/8”

hex bolt (#6), 1/4” flat washer (#7), and 1/4-20 ser-

rated nut (#8) as shown. Just snug the bolt for now, it

will need to be adjusted in step #8.

8. Reinstall the factory bolt that was removed in

step #3, through the bracket that is bolted onto the

side of the Cool Air Box. Adjust the box for fit, and

tighten both bolts.

A.

B.

C.

Tube

Adapter

Gasket

O-ring

Calibration Plate

Bolts & Washers

Factory Tube

Filter Minder

12. Double check your work! Make sure there is no foreign material in the

intake path. Make sure all clamps, hoses, bolts,

and screws are tight.

13. Reconnect the negative battery

cables!

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 [email protected] www.airaid.com REV.10.23.13

P/N 790-551 Aerosol Spray

P/N 790-550 Squeeze Spray

Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST week-

days for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and

packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air

filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WA-

TER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.

Weather strip

10. Install the MAF sensor into the Calibration Plate

on the Cool Air Box using two 8-3/8” button head

bolts (#9), as shown. Reconnect the MAF sensor

wiring harness.

Do Not Use The Factory Screws

11. Install the Airaid Premium Filter (#1) onto the

filter adapter, and tighten the hose clamp. Next in-

stall the Top Panel (#3) onto the top of the Cool Air

Box using six 8-32x3/8” button head bolts (#9), and

#8 flat washers (#10). Install the weather strip (#5)

onto the edge of the top panel as shown

Factory Tube MAF Sensor

Top Panel

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number,

and click View Details.

FILTER IDENTIFICATION

720-472 Airaid Oiled Media 721-472 Airaid SynthaMax Dry Media - Red

722-472 Airaid SynthaMax Dry Media - Black 723-472 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we

suggest using the AIRAID Filter

Tune-Up Kit!

Synthamax Air Filters do not re-

quire oil. Service air filter as need-

ed by cleaning with common non-

petroleum all-purpose household

cleaner and water. Simple Green®,

Formula 409® or equivalent works

great. Apply cleaner to outside of

air filter and allow to soak. Then

flush filter clean from the inside out

with a garden hose and repeat steps

if necessary. Do not apply high

pressure water or air to clean filter.

Allow filter to air dry and reinstall.