INSTALLATION INSTRUCTIONS - Professional AV Equipment …

I N S T A L L A T I O N I N S T R U C T I O N S

PAC527

PAC527F

PAC527FC

PAC527FxP4

PAC527FxP6

PAC527F-KIT

PAC527CVR-KIT

PACPL1

In-Wall Box and Accessories

PAC527 Series

PAC527 Series Installation Instructions

2

DISCLAIMERMilestone AV Technologies and its affiliated corporations andsubsidiaries (collectively “Milestone”), intend to make thismanual accurate and complete. However, Milestone makes noclaim that the information contained herein covers all details,conditions or variations, nor does it provide for every possiblecontingency in connection with the installation or use of thisproduct. The information contained in this document is subjectto change without notice or obligation of any kind. Milestonemakes no representation of warranty, expressed or implied,regarding the information contained herein. Milestone assumesno responsibility for accuracy, completeness or sufficiency ofthe information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies.All rights reserved.

DEFINITIONSMOUNTING SYSTEM: A MOUNTING SYSTEM is theprimary Chief product to which an accessory and/or componentis attached.

ACCESSORY: AN ACCESSORY is the secondary Chiefproduct which is attached to a primary Chief product, and mayhave a component attached or setting on it.

COMPONENT: A COMPONENT is an audiovisual itemdesigned to be attached or resting on an accessory or mountingsystem such as a video camera, CPU, screen, display,projector, etc.

WARNING: A WARNING alerts you to the possibility ofserious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility ofdamage or destruction of equipment if you do not follow thecorresponding instructions.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Failure to read, thoroughly understand, andfollow all instructions can result in serious personal injury,damage to equipment, or voiding of factory warranty! It is theinstaller’s responsibility to make sure all accessories areproperly assembled and installed using the instructionsprovided.

WARNING: Failure to provide adequate structural strengthfor this accessory can result in serious personal injury ordamage to equipment! It is the installer’s responsibility tomake sure the structure to which this accessory is attachedcan support five times the combined weight of all equipment.Reinforce the structure as required before installing theaccessory.

WARNING: Exceeding the weight capacity can result inserious personal injury or damage to equipment! It is theinstaller’s responsibility to make sure the combined weight ofall components located in the accessory does not exceed40 lbs (18.1 kg).

• Each PAC527 may hold up to 4 individual backplanes(2 complete) and each individual backplane may hold amaximum weight of 10 lbs (4.5 kg)

• A half backplane (after separation) may hold amaximum weight of 5 lbs (2.3 kg).

WARNING: Use this accessory only for its intended use asdescribed in these instructions. Do not use attachments notrecommended by the manufacturer.

WARNING: Never operate this accessory if it is damaged.Return the accessory to a service center for examination andrepair.

WARNING: For indoor use only.

IMPORTANT ! : The PAC527 accessory is designed to bemounted to either a 2" x 3" or 2" x 4" wood stud wall 16" oncenter, or a 2" x 3"-25ga (minimum) or 2" x 4"-25ga (minimum)steel studs wall.NOTE: Spacings - Minimum spacings between the 120 Vac

power components and the A/V components shall bemaintained for safe operation of the equipment wheninstalled in accordance with the National Electric Code,ANSI/NFPA 70.

NOTE: When selecting a Listed 120 Vac Receptacle for use asthe main power source for the PAC series boxes (topower the A/V equipment), make sure that ACReceptacle is rated at least 15A and it is used in thebuilding’s AC branch circuit that is connected to acircuit breaker rated at least 15A. Do not connect morethan 12A from the Receptacle.

In the U.S., the equipment shall be installed per the applicablerequirements of the National Electrical Code, CSA C22.1.

In Canada, the equipment shall be installed per the applicablerequirements of the National Electrical Code, ANS/NFPA 70.

NOTE: It is the installer’s responsibility to ensure that theenclosure is bonded to the ground in the switch box, inaccordance with the National Electric Code, ANSI/NFPA70 or Canadian Electrical Code, CSA C22.1. A greengrounding screw is provided in the enclosure for thepurpose, if required.

IMPORTANT ! : The PAC527 mounts are designed toaccommodate the following Chief power kits ONLY:

• PAC527P4-KIT• PAC527P6-KIT

--SAVE THESE INSTRUCTIONS--

DIMENSION DRAWINGS are located at the end of theseInstallation Instructions.

Installation Instructions PAC527 Series

3

ADDITIONAL SAFETY INSTRUCTIONSSPECIFIC TO PAC527FxP4 / PAC527FxP6

READ ALL INSTRUCTIONS BEFORE USING THISPRODUCT!!!!

DANGER: TO REDUCE THE RISK OFELECTRIC SHOCK:

1. Always turn off power at source before installing the outlet.

WARNING: TO REDUCE THE RISK OF

BURNS, FIRE, ELECTRIC SHOCK, OR INJURY TOPERSONS:

• Always turn off power at source before servicing orremoving the outlet.

• Do not use outdoors - For indoor use only.• Route cables as shown in these installation

instructions.• To disconnect, turn off power at source.

WARNING: RISK OF ELECTRIC SHOCK!Make sure the outlet is properly grounded. See groundinginstructions.

CAUTION: This equipment must be installedand assembled by qualified service personnel in accordancewith local building and electrical codes.

NOTE: Knockouts are provided for ease of installation. Anyunused knockouts that have been punched are to beclosed up with a metal plug.

Ambient Temperature - The manufacturer’s maximum ambienttemperature is 104°F (40°C) and minimum ambienttemperature is 30°F (-1°C) so that the installer is able todetermine acceptability of use of Accessories and components.

--SAVE THESE INSTRUCTIONS--

IMPORTANT ! : DIMENSION DRAWINGS are located atthe end of these Installation Instructions.

TABLE OF CONTENTS

IMPORTANT ! : DIMENSION DRAWINGS are located at the end of these Installation Instructions.


4

LEGENDTighten Fastener

Apretar elemento de fijación

Befestigungsteil festziehen

Apertar fixador

Serrare il fissaggio

Bevestiging vastdraaien

Serrez les fixations

Loosen Fastener

Aflojar elemento de fijación

Befestigungsteil lösen

Desapertar fixador

Allentare il fissaggio

Bevestiging losdraaien

Desserrez les fixations

Phillips Screwdriver

Destornillador Phillips

Kreuzschlitzschraubendreher

Chave de fendas Phillips

Cacciavite a stella

Kruiskopschroevendraaier

Tournevis à pointe cruciforme

Open-Ended Wrench

Llave de boca

Gabelschlüssel

Chave de bocas

Chiave a punte aperte

Steeksleutel

Clé à fourche

By Hand

A mano

Von Hand

Com a mão

A mano

Met de hand

À la main

Hex-Head Wrench

Llave de cabeza hexagonal

Sechskantschlüssel

Chave de cabeça sextavada

Chiave esagonale

Zeskantsleutel

Clé à tête hexagonale

Pencil Mark

Marcar con lápiz

Stiftmarkierung

Marcar com lápis

Segno a matita

Potloodmerkteken

Marquage au crayon

Drill Hole

Perforar

Bohrloch

Fazer furo

Praticare un foro

Gat boren

Percez un trou

Adjust

Ajustar

Einstellen

Ajustar

Regolare

Afstellen

Ajuster

Remove

Quitar

Entfernen

Remover

Rimuovere

Verwijderen

Retirez

Optional

Opcional

Optional

Opcional

Opzionale

Optie

En option

Security Wrench

Llave de seguridad

Sicherheitsschlüssel

Chave de segurança

Chiave di sicurezza

Veiligheidssleutel

Clé de sécurité


5

TOOLS REQUIRED FOR INSTALLATION

PARTS INCLUDED

3/16" 1/4" } OPTIONAL

E (1)[PAC527]

F (1) [Template/

A (4)1/4 x 2-1/2"

C (8)06 x 3/8"

B (8)06-32"

D (4) 3/8"

Temporary Cover]

G (1)[PAC527F]

F (1) [Template/

A (4)1/4 x 2-1/2"

C (8)06 x 3/8"

B (8)06-32"

D (4) 3/8"

Temporary Cover]

H (1)[PAC527FC]

F (1) [Template/

A (4)1/4 x 2-1/2"

C (8)06 x 3/8"

B (8)06-32"

D (4) 3/8"

Temporary Cover]

PAC527

PAC527F

PAC527FC


6

PARTS - continued

J (1)[PAC527FxP4]

F (1) [Template/

A (4)1/4 x 2-1/2"

C (8)06 x 3/8"

B (8)06-32"

D (4) 3/8"

Temporary Cover]

PAC527FxP4

K (1)[PAC527FxP6]

F (1) [Template/

A (4)1/4 x 2-1/2"

C (8)06 x 3/8"

B (8)06-32"

D (4) 3/8"

Temporary Cover]

PAC527FxP6

L (1) [Flange]

F (1) [Template/

M (8)10-24 x 1/4"

Temporary Cover]

PAC527F-KIT

N (1) [Cover]PAC527CVR-KIT

P (2)#06 x 1-1/4"

Q (2)#06 x 1-1/2"

S (2).259 x .156 x .625"

T (2)#06

R (1) 1/8"[security]

PACPL1 U (2)[Backplane]

V (8)10-24 x 3/8"


7

OPTIONAL PARTS PER CUSTOM CONFIGURATION (NOT INCLUDED)

ADDITIONAL INFORMATION

Conduit pipe 1/2", 1" or 1-1/4"

Conduit connectors3" x 2" Steel OldWork Switch Box(2" deep)Raco #420 orequivalent

Electrical outlet

Narrow Handy BoxCover, DuplexRaco #864 orequivalent

NOTE: Grounding screw installed at factory in PAC527, PAC527F, PAC527FC, PAC527FxP4, and

10-32grounding screw

Earthing symbol IEC 60418 No. 5019affixed adjacent to grounding terminal

PAC527FxP6 in-wall boxes. Grounding screw is located on one side of the PAC527 box.

ASSEMBLY AND INSTALLATIONIMPORTANT ! : In the following instructions, thereference to PAC527 includes the following models:

• PAC527• PAC527F• PAC527FC• PAC527FxP4• PAC527FxP6

The PAC527 is intended for use in both installations where anexisting finished drywall wall is present, and where the wallsurface has not been finished and the structural studs areexposed. The wall then must be finished around the opening ofthe box after the box has been installed.

Locating PAC5271. Identify a suitable wall location for the accessory.

2. Locate and mark studs using a stud sensor.

3. Identify possible structural conflicts (electrical wiring,plumbing, gas lines, HVAC).

WARNING: ELECTRICAL SHOCK HAZARD! CUTTINGOR DRILLING INTO ELECTRICAL WIRES OR CABLESCAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!ALWAYS make certain area behind mounting surfaces is freeof electrical wires and cables before cutting, drilling orinstalling fasteners.

WARNING: EXPLOSION AND FIRE HAZARD! CUTTINGOR DRILLING INTO GAS PLUMBING CAN CAUSE DEATHOR SERIOUS PERSONAL INJURY. ALWAYS make certainarea behind mounting surfaces is free of gas, water, waste orany other plumbing before cutting, drilling or installingfasteners.

4. Determine all additional/optional components required:

• Conduit pipe• Conduit connectors (both large and small)• Electrical box(es) (3" x 2")• Steel electrical box cover(s)• Electrical outlet(s)

WARNING: All wiring should beperformed by a licensed electrician followingall local codes and ordinances.


8

INSTRUCTIONS FOR PAC527FxP4 /PAC527FxP6 OnlyIsolated Ground ReceptacleThis product incorporates an isolated ground receptacle,identified by the orange triangle on its face. This feature may beuseful to reduce common noise in the connected equipment. Itsintended use is to reduce electrical noise (electromagneticinterference) by purposely insulating the grounding circuit fromany metallic wiring system. The ground pin of the receptacle isconnected to the green/yellow wire and is isolated from themetal mounting yoke of the receptacle. The accessible metal ofthe product is connected to the green wire. If it is not desired touse this feature, connect the green/yellow and green wirestogether.

References

Application Guide for Isolated Ground Wiring Devices 2007,National Electrical Manufacturers Association (NEMA)

IEEE Std 1100™-2005, “IEEE Recommended Practice forPowering and Grounding Electronic Equipment” (EmeraldBook), Section 8.5.3.2.IEEE Std 142™-2007, “IEEE Recommended Practice forGrounding of Industrial and Commercial Power Systems”(Green Book), Sections 5.5.1, 5.5.2NFPA-70, “National Electrical Code”, Article 250.146Connecting Receptacle Grounding Terminal to Box.

• (D) Isolated Ground Receptacles. Where installedfor the reduction of electrical noise (electromagneticinterference) on the grounding circuit, a receptaclein which the grounding terminal is purposefullyinsulated from the receptacle mounting means shallbe permitted. The receptacle grounding terminalshall be connected to an insulated equipmentgrounding conductor run with the circuit conductors.This equipment grounding conductor shall bepermitted to pass through one or more panel boardswithout a connection to the panel board groundingterminal bar as permitted in 408.40, Exception, soas to terminate within the same building or structuredirectly at an equipment grounding conductorterminal of the applicable derived system or service.Where installed in accordance with the provisions ofthis section, this equipment grounding conductorshall also be permitted to pass through boxes, wireways, or other enclosures without being connectedto such enclosures.

• Informational Note: Use of an isolated equipmentgrounding conductor does not relieve therequirement for grounding the raceway system andoutlet box.

C22.2 No. 1, “Canadian Electrical Code, Part 1”, Rule 10-906Bonding conductor connection to circuits and equipment.

• (6) A bonding jumper shall be installed to connectthe bonding conductor to the grounding terminal ofa receptacle and in such a manner thatdisconnection or removal of the receptacle will notinterfere with, or interrupt grounding continuity.

• (7) In the case of metallically enclosed systemswhere the grounding path is provided by the metalenclosure, a bonding jumper shall be installed tobond the grounding terminal of the receptacle to theenclosure.

• (8) Notwithstanding Sub-rules (6) and (7), thebonding jumper, in the case of receptacles havinggrounding terminals isolated from the mountingstrap required for special equipment, shall bepermitted to be extended directly back to thedistribution panel.

WARNING: IMPROPER INSTALLATION CAN RESULT INDEATH OR SERIOUS PERSONAL INJURY! This enclosureshould be installed by qualified personnel.

NOTE: The PAC527FxP4 and PAC527FxP6 must beconnected to a 15 Amp branch circuit.

Prepare for Wiring1. Remove and save three Phillips head screws holding power

kit within box. (See Figure 1)

2. Remove the power kit from the in-wall box. (See Figure 1)

Figure 1

1 x 3

2

(PAC527FxP4shown as example)

Lower tabon power kit

Power kit

4

Fit slots in power kitlower tab aroundtwo fasteners


9

3. Wire the outlet box(es) as required. Refer to Table 1 andTable 2 for input and output specifications. (See Figure 2)

Table 1: Input Specifications

Table 2: Output Specifications

CAUTION: Isolated ground-mounting means NOTgrounded. Grounding wire connection required.

IMPORTANT ! : If a separate isolated green/yellowground wire is installed in the building wiring, attach itseparately to the green/yellow isolated ground wire onbox. If there is no separate green/yellow isolated groundwire, connect green ground wire to both green/yellowisolated ground wire and green box ground wire on box.NOTE: The grounding conductors serving this outlet are to be

connected to earth ground at the service equipment orother acceptable building earth ground such as thebuilding frame in the case of a high-rise steel-framestructure. Connections should be made with minimumAWG 14 copper wire intended for use on a 15 Ampcircuit. The conductors used to connect the outlet to theline or bus and ground shall not be any longer thannecessary and shall avoid unnecessary bends.

NOTE: An insulated grounding conductor that is identical insize and insulation material and thickness to thegrounded and ungrounded circuit supply conductors,except that it is green with or without one or moreyellow stripes, is to be installed as part of the circuit thatsupplies the outlet. Refer to Table 250-122 of theNational Electrical Code regarding the appropriate sizeof the grounding conductor.

NOTE: Pressure terminal or pressure splicing connectors andsoldering lugs used in the installation of the outlet shallbe identified as being suitable for the material of theconductors. Conductors of dissimilar metals shall notbe intermixed in a terminal or splicing connector wherephysical contact occurs between dissimilar conductorsunless the device is identified for the purpose andconditions of use.

Figure 2

4. Replace the power kit in the PAC527, fitting the two slots inthe power kit lower tab around two fasteners in the PAC527.(See Figure 1) and (See Figure 2)

5. Tighten three Phillips screws to secure power kit in thePAC527. (See Figure 2)

Outlet Box UseNOTE: The "PROTECTED" light indicates that the surge

protection circuitry is active and operational.

Figure 3

InputInput voltage, frequency 125 V AC, 60 Hz

Input connection type 4x14 AWG stranded, UL Style1015, CSA TEW

Input Wire colors Black - LineWhite - NeutralGreen - Box GroundGreen/Yellow - Isolated Ground

Input wire length (ft.) 1 (with a 3/4" stripped end)

OutputOutput 15 A, 1875 W

Power consumption <0.5 watt

Fuses Thermal current interrupting circuitsare in MOVs

Quantity/Type Duplex NEMA 5-15R Isolated GroundReceptacle

Color/Markings Grey with protection symbol (Orangetriangle)

4

GREEN(box ground)

5 x 3

(PAC527FxP4 shown as example)

WHITE(neutral)

BLACK (line)

GREEN/YELLOW (isolated ground)

Lower tabon power kit

"PROTECTED"indicator light

(PAC527FxP4shown as example)


10

PAC527 Site Preparation1. Using a level, draw a horizontal line at the lower edge of the

install site. (See Figure 4)

2. Create an exploratory hole to confirm edge of the studs.

3. Using the line drawn in Step 1 as lower edge and placingbetween studs, use the enclosed template (F) to draw linesaround corners of template, and connect lines on bottom,top and sides. (See Figure 4)

Figure 4

4. Cut along outside edge of line using a utility knife andremove drywall.

5. Check stud depth within the wall.

• If 3-1/2" or greater, proceed to PAC527 BoxPreparation and Installation.

• If less than 3-1/2" deep, proceed to Step 6.

6. If present, remove box flange by loosening screws. (SeeFigure 5)

CAUTION: Injury may occur on sharp edges. Carefullydiscard the removable tabs. Avoid sharp edges.

7. Snap off removable tabs at perforations provided.

8. Reinstall box flange.

9. Fasten flange in place by tightening screws loosened inStep 6.

Figure 5

PAC527 Box Preparation and Installation1. Remove knock-outs as determined in Step 4 of Locating

PAC527 section. (See Figure 6)

Figure 6

3

1

3

3

(F)

6x 8

Flange

6

8

9

1


11

2. Loosely attach required conduit and conduit connectors,switch boxes, outlets, etc (not included) to PAC527 toenable fitting into the wall opening. (See Figure 7)

Figure 7

3. Feed conduit attached to PAC527 through cut-out in walland insert PAC527 into wall opening. Tighten componentconnections.

4. Drill pilot holes (at least 2 on each side of PAC527) intostuds through mounting holes in PAC527.

• Wood studs: use 3/16" drill bit• Steel studs: use 1/4" drill bit

5. Install PAC527 to studs using four 1/4 x 2-1/2" Phillips flathead screws (A) and four 3/8" flat washers (D) throughPAC527 and pilot holes. (See Figure 8)

Figure 8

NOTE: If installing in a stud wall BEFORE the drywall isinstalled, remove outer flange from PAC527 beforeinstalling the PAC527. (See Figure 9)

Figure 9

(C x 4)2

Use four 06 x 3/8" Phillipsscrews (C) and four 06-32"nuts (B) to assemble switchbox from either inside oroutside the PAC527.

(A) x 45

(D) x 4

4 x 2 (minimum)each side


12

Installing Backplanes (PACPL1)IMPORTANT ! : The backplanes ship installed in thePAC527 / PAC527F / PAC527FC / PAC527FxP4 /PAC527FxP6 and may be removed, re-sized orrearranged as necessary. A backplane kit (PACPL1) isalso available.1. FOR BACKPLANES SHIPPED IN PAC527 BOXES ONLY:

Loosen screws (leaving them in the backplanes) holding thebackplanes in the PAC527 box, and remove backplanesfrom box. (See Figure 10)

Figure 10

2. If required, break the backplanes along the scored mid-line.(See Figure 11)

Figure 113. Attach components to backplanes following component

manufacturer’s instructions.

4. PACPL1 ONLY: Loosely install two 10-24 x 3/8" Phillipsexternal tooth screws (V) into each backplane half. (SeeFigure 11)

5. Reinstall backplanes directly under tabs located at any ofthe three levels in the PAC527.

6. Fasten in place using Phillips screws loosened in Step 1;OR Phillips screws (V) installed in Step 4. (See Figure 11)

NOTE: Each individual section of backplane must be fastenedat each end with one of the Phillips screws.

Figure 12

Adding Template/Temporary CoverNOTE: OPTIONAL: Install template (F), if necessary, as a

temporary cover to protect interior of PAC527 box fromdebris.

1. Fold tabs of template (F) in and insert into PAC527 opening.(See Figure 13)

Figure 13

1

Mid-line

2

4 (V) x 2

3 levels forbackplaneattachment

6

5

(F)


13

PAC527F-KIT1. Loosely install eight 10-24 x 1/4" Phillips head screws with

external teeth (M) into holes in PAC527 sides. (See Figure 14)NOTE: If the outer edge of the PAC527 needs to be removed,

use the inner hole for flange attachment. (See Figure 14)

Figure 142. Slide flange (L) into PAC527 over installed screws, and

tighten screws. (See Figure 15)

Figure 15

PAC527CVR-KIT1. Break away the tab(s) on the cover (N) to allow wire exit

from the PAC527, and to meet ventilation needs of thecomponents. (See Figure 16)

Figure 16

2. Gather all wires and route through the cover opening(s).(See Figure 17)

3. Install cover (N) and fasten with two #6 x 1-1/4" Phillips self-tapping screws (P) [#6 x 1-1/2" button head self-tappingscrews (Q) for security], two spacers (S) and two #6 lockwashers (T). (See Figure 17)

Figure 17

Outer hole

Inner hole

(L)

2

2

(M) x 8

(N)

Break away tab(s)1

(N)

(S)

(P or Q) x 2

(T)


14

DIMENSIONS

13.21335.6

12.00304.8

10.00254.0

5.00127.0

0.5012.7

TYPICAL

1.5038.1

TYPICAL

1.2531.8

TYPICAL

0.20 5.2X 0.95 24.2

1.0025.4

FINGER HOLD

BREAK-OFF LINE

NOTE:SCREWS ARE THREADED TO THE BACKPLANE1.TWO PIECES (ONE PIECE SHOWN ABOVE),2.

INCLUDED WITH ENCLOSURE

PAC527

DIMENSIONS: INCHES [MILLIMETERS]


15

DIMENSIONS - continued

13.21335.6

12.00304.8

10.00254.0

5.00127.0

0.5012.7

TYPICAL

1.5038.1

TYPICAL

1.2531.8

TYPICAL

0.20 5.2X 0.95 24.2

1.0025.4

FINGER HOLD

BREAK-OFF LINE



PAC527F



16


13.21335.6

12.00304.8

10.00254.0

5.00127.0

0.5012.7

TYPICAL

1.5038.1

TYPICAL

1.2531.8

TYPICAL

0.20 5.2X 0.95 24.2

1.0025.4

FINGER HOLD

BREAK-OFF LINE



23.26590.9

15.40391.1

14.25362.0

3.94100.0

6.38161.9

1.3734.8

22.00558.8

1.0025.4

1.3734.8

0.7519.1

0.256.4

1.0025.4

1.7544.5

3.5088.9

5.00127.0

5.00127.0

5.00127.0

THREEBACKPLANEDEPTHPOSITIONSAVAILABLE

3.8898.4

2.8873.0

1.7344.0

2.0050.8

0.348.6

MOUNTINGHOLE KNOCKOUT

11.00279.4

20.00508.0

BREAK-OFFREGION FOR2 1/2" WALLINSTALLATION

2.3860.3

2.3860.3

2.0050.8

3.6392.1

2.0050.8

3.6392.1

1.3734.8A

B

RECOMMENDED ELECTRICAL BOX:RACO 560 3" X 2" BOX, 2 3/4" DEEPGANGABLE OR EQUIVALENT.

RECOMMENDED ELECTRICAL BOXCOVER: RACO 864 SINGLE DUPLEX

0.8822.2

TRADE CONDUIT SIZE 1/2"METRIC CONDUIT SIZE 16mm

1.3834.9

TRADE CONDUIT SIZE 1"METRIC CONDUIT SIZE 27mm1.73

44.0TRADE CONDUIT SIZE 1-1/4"METRIC CONDUIT SIZE 35mm

DETAIL ASCALE 1 : 1.5

3.7394.9

0.112.9

1.1328.6

2.0953.1

3.4387.0

DETAIL BSCALE 2 : 5

PAC527FC



17

DIMENSIONS - continuedPAC527FxP4

PAC527FxP4 PAC527FxP6

PAC527FxP6

18.20462.3

13.90353.0

USEABLE STORAGE SPACE

15.40391.1

22.18563.4

3.8898.4

23.26590.9

0.092.4

*SEE PAC527F FOR ADDITIONAL BOX DIMENSIONS*

AC LINE POWER CONDITIONER 125 V~, 60 Hz, 15 A

4x14 AWG STRANDED WIRE W/ ISOLATED GROUND

SURGE PROTECTION

EMI/RFI FILTERING

POWER CONSUMPTION: <0.5 WATT

PAC527FxPx



18


23.26590.9

15.40391.1

13.90353.0

21.76552.8

4.75120.7

0.4311.0

PAC527F-KIT


13.38339.7

13.81350.8

21.75552.5

1.5038.0

5.00127.0

3.6392.10.69

17.5

PAC527CVR-KIT



19


13.21335.6

12.00304.8

10.00254.0

5.00127.0

0.5012.7

TYPICAL

1.5038.1

TYPICAL

1.2531.8

TYPICAL

1.0025.4

FINGER HOLD

0.9524.2 0.20

5.2

BREAK-OFF LINE

NOTE:SCREWS ARE THREADED TO THE BACKPLANE1.PACPL1 KIT INCLUDES TWO BACK PLANE PIECES AS2.

SHOWN ABOVE

PACPL1



USA/International A 6436 City West Parkway, Eden Prairie, MN 55344P 800.582.6480 / 952.225.6000F 877.894.6918 / 952.894.6918

Europe A Franklinstraat 14, 6003 DK Weert, NetherlandsP +31 (0) 495 580 852F +31 (0) 495 580 845

Asia Pacific A Office No. 918 on 9/F, Shatin Galleria18-24 Shan Mei StreetFotan, Shatin, Hong Kong

P 852 2145 4099F 852 2145 4477

Chief, a products division ofMilestone AV Technologies

8800-002967 Rev012017 Milestone AV Technologies

www.milestone.com09/17

http://www.milestone.com

INSTALLATION INSTRUCTIONS - Professional AV Equipment …

Documents