This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
INSTALLATION INSTRUCTIONS FOR PART 95-6511-17
APPLICATIONSChrysler
Aspen 2008-09/Sebring 2007-09Town and Country 2008-09/300/300c 2008-09
Liberty 2008-09/Wrangler 2007-09**(Modifications to radio cavity required)
MitsubishiRaider 2008
WIRING AND ANTENNA CONNECTIONS (Sold Separately)Harness:• XSVI-6522-NAV - Chrysler CAN rap harness 07-up• CHTO-03 - Chrysler CAN amp harness 07-up Antenna Adapter:• 40-EU10 - European antenna adapter 02-up
*Note: Refer also to the instructions included with the aftermarket radio.
KNOWLEDGE IS POWEREnhance your installation and fabrication skills byenrolling in the most recognized and respectedmobile electronics school in our industry.Log onto www.installerinstitute.com or call800-354-6782 for more information and take stepstoward a better tomorrow.
95-6511-17 DASH DISASSEMBLY
CHRYSLER ASPEN 2008-2009DODGE DURANGO 2008-2009
A
123
69
POWEROUTLET
1 2 3 4 5 6
POWEROUTLET
B
123
1 2 3 4 5 6
69
C
1
1
Remove (2) screws from bottom edgeof center dash trim panel. Unsnapand remove the panel. (Figure B)
Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.
3
Remove (4) screws securing theradio. Unplug and remove radio.(Figure C)
4
Unsnap and remove storage cup holder assembly. (Figure A)
2
Continue to kit assembly.
95-6511-17 DASH DISASSEMBLY
CHRYSLER SEBRING 2007-2009A
B
2
1
Remove (4) 7MM screws securingradio. Unplug and remove radio.(Figure B)
Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.
3
Unclip entire panel surrounding radioincluding a/c vents and clock. Unplugand remove panel. (Figure A)
2
Continue to kit assembly.
95-6511-17 DASH DISASSEMBLY
CHRYSLER TOWN AND COUNTRY 2008-2009DODGE GRAND CARAVAN 2008-2009
A
B
C
3
1
Lift up on panel above radio thenremove (2) Phillips screws exposed atfront edge of radio trim panel.(Figure B)
Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.
3
Remove (3) plastic push pins per sideof bottom trim panel then slide paneltoward rear of van to access (2)screws on bottom of radio trim panel.(Figure C)
4
Remove (2) screw covers facing upabove radio then remove the (2)Phillips screws exposed. (Figure A)
2
Continued on page 3.
95-6511-17 DASH DISASSEMBLY
D
E
1 2 3 4 5 6 AUX
AUX
SET
VOLUME
PUSH ON PUSH AUDIO/SELECTAM
FM
DISC
LIST
MUSICTYPE
SEL;ECT
TUNE/SCROLL
SEEKSEEK SCAN TIME INFO RW FFU
F
4
5 Remove (2) Phillips screws exposedat bottom edge radio trim panel.(Figure D)
Remove (2) T25 Torx screws from the topof the radio trim panel. (Figure G)
Unclip and remove the entire radio trimpanel including the climate controls.(Figure H)
9
Continue to kit assembly.
95-6511-17 KIT ASSEMBLY
15
A
DOUBLE DIN RADIO PROVISION
Attach the Double DIN brackets/trimplates to the Double DIN Radio usingthe screws supplied with the Radio.(Figure A)
1
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
STACKED ISO UNITS PROVISION
Attach the Double DIN brackets/trimplates to the stacked ISO units usingthe screws supplied with the units.(Figure A)
1
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
95-6511-17 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ-ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with thehead unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc . . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.All colors may not be present on all leads due to manufacturer’s specifications.