ETA ELECTRONIC TRAFFIC AVOIDANCE INSTALLATION INSTRUCTIONS for RHD Manual Ref. no. AIM 000 073-1 FOR ** R1 * R Corolla Verso (*) Verify whether the vehicle has a prewired ETA by checking the presence of the ETA-antenna in the proximity of the rear view mirror. REQUIRED PARTS ETA ANTENNA (*) ALREADY PREWIRED NOT PREWIRED MAIN KIT ETA PZ445-T9331-00 ANTENNA KIT - PZ445-T9281-00 ETA BRACKET - PZ425-E8331-60 FAKRA CONNECTOR - PZ445-E9330-01 A-PILLAR CLIPS: 75597-05010 / 62217-13010
17
Embed
INSTALLATION INSTRUCTIONS for Corolla Verso - Toyota …D7CF6257-E414-465C... · installation instructions for rhd ... corolla verso (r1) electronic traffic avoidance ... 3/29/2004
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
ETAELECTRONIC TRAFFIC AVOIDANCE
INSTALLATION INSTRUCTIONS for
RHD
Manual Ref. no. AIM 000 073-1
FOR **R1*R
Corolla Verso
(*) Verify whether the vehicle has a prewired ETA by checking the presence of theETA-antenna in the proximity of the rear view mirror.
REQUIRED PARTS
ETA ANTENNA (*)
ALREADY PREWIRED NOT PREWIRED
MAIN KIT ETA� �
PZ445-T9331-00
ANTENNA KIT - �
PZ445-T9281-00
ETA BRACKET � -
PZ425-E8331-60
FAKRA CONNECTOR � -
PZ445-E9330-01
A-PILLAR CLIPS: 75597-05010 / 62217-13010
Corolla Verso (R1) ELECTRONIC TRAFFIC AVOIDANCE
Corolla Verso (RHD) - 202-04
PRECAUTIONS
• Be sure to disconnect the negative (-) lead from the battery ter-minals.
• Do not pinch the rear wiring or harness in the tightened part.
• When passing the wires through the bulkhead or other panels,use a grommet to ensure waterproofing.
• Protect the wiring using tape when it is passed through a hole.
• When disconnecting the connectors, be sure to grip the con-nector body. Do not tug on the wiring.
• Do not forcibly pull any car wiring harness. Rough tugging mayresult in opened connections, or a broken wire or harness.
• Confirm that lamps, horn, wiper and other car accessories operatenormally.
• Protect your car using wing covers, seat and so on.
• Use the correct tool when tightening bolts or nuts.
• Before drilling a hole, check that the rear of the mounting wallis clear.
• Be sure to firmly tighten connectors and terminals.
• Before connecting the power wiring to the battery, check thewiring connections, harness, etc. to see that they are properlysecured.
• Check body and trim near area of installation to be certain nodirt or scratches resulted from the installation.
PLEASE READ THOROUGHLY THESE PRECAUTIONS BEFORE THE INSTALLATION
Main Kit ETA .................................................................................................................................................................... 4
ETA Bracket Kit (only in case of a prewired ETA-antenna) ............................................................................................... 4
Installation of the RDS-Antenna Wire .................................................................................................................. 10
Installation of the RDS-Antenna Strip ................................................................................................................. 12
Installation of the RDS-Tuner ............................................................................................................................... 13
Installation of the RDS-Tuner ............................................................................................................................... 15
(For installation of navigation, please refer to the navigation installation manual AIM 000 071-0)
Corolla Verso (R1) ELECTRONIC TRAFFIC AVOIDANCE
Corolla Verso (RHD) - 3 02-04
TABLE OF CONTENTS
For vehicles without prewired ETA-antenna
For vehicles with prewired ETA-antenna
Corolla Verso (RHD) - 402-04
Corolla Verso (R1) ELECTRONIC TRAFFIC AVOIDANCE
MAIN KIT ETA PZ445-T9331-00
1 2
7
ETA BRACKET KIT(only in case of a prewired ETA-antenna) PZ425-E8331-60
c
No. Part Name Part No. Qty
RDS-TUNER PZ445-T9331-02 1
SUBWIRE HARNESS PZ445-T9331-03 12
1
No. Part Name Part No. Qty
ETA BRACKET 1
BOLT (M 5X8) 2
FOAM TAPE 2
BUTYL TAPE 1f
e
c
7
e f
Corolla Verso (R1) ELECTRONIC TRAFFIC AVOIDANCE
Corolla Verso (RHD) - 5 02-04
RDS-ANTENNA KIT PZ445-T9281-00
No. Part Name Part No. Qty
ANTENNA STRIP PZ445-E9281-01 1
RDS-ANTENNA WIRE PZ445-T9281-01 1
FAKRA CONNECTOR PZ445-E9330-01 1
TAPPING SCREW 13
5
D
6
D
56
A-PILLAR CLIPS 75597-05010 / 62217-13010
No. Part Name Part No. Qty
CLIPS FOR A-PILLAR (see p. 8) 75597-05010 / 62217-13010 2
3
Corolla Verso (RHD) - 602-04
Corolla Verso (R1) ELECTRONIC TRAFFIC AVOIDANCE
INSTALLATION OVERVIEW
19
1
D
(**)
1 (*)
IMPORTANT: Please verify whether the vehicle has a prewired ETA-antenna or not. In case of a prewiredETA-antenna, the ETA bracket kit is necessary.
RDS-ANTENNA WIRE
RDS-TUNER (*) In case of a non-prewired RDS-tuner (**) In case of a prewired RDS-tuner
ANTENNA STRIP
NAVIGATION ECU19
6
1
D
6
Corolla Verso (R1) ELECTRONIC TRAFFIC AVOIDANCE
Corolla Verso (RHD) - 7 02-04
VEHICLE DISASSEMBLY
1. Remove the front door scuff plate (L).
: Hook (9x)
1
2. Remove the passenger seat .: Bolt (5x): Cover (3x)
: Hook 3 x (2x)101100
2
Fig. 1
Fig. 2
For vehicles without prewired ETA-antenna
1
2
100
101
Fasten the bolts with specified torquewrench (37 Nm) when reassembling.
4. Remove the left front pillar garnish .: Clip (2x)
5
Do not reuse the removed clips. Ordernew clips (part nrs. 75597-05010 and62217-13010).
CAUTION
ON OFF DOOR
ON OFF DOOR
Fig. 5
5.a) Remove the map lamp assembly .
: Clip (2x): Bolt (2x)
b) Disconnect the connector.
88
Fig. 3
Fig. 4
102
5
4
Corolla Verso (R1) ELECTRONIC TRAFFIC AVOIDANCE
Corolla Verso (RHD) - 9 02-04
ON OFF DOOR
Fig. 6
6. Remove the holder of the sun visorby turning it counterclockwise.10
98
7. Pull the sun visor to the LH side ofthe vehicle.
10
90°
9
10
Fig. 7
10
Corolla Verso (RHD) - 1002-04
Corolla Verso (R1) ELECTRONIC TRAFFIC AVOIDANCE
INSTALLATION OF THE RDS-ANTENNA WIRE
1. If not yet insulated, do so with the com-plete ground wire of the RDS-antennawire by wrapping it into tape .12D
Fig. 8
D
12
Ground wire
2. Before routing the RDS-antenna wire, protect the RDS-antenna black
wired pin and the RDS-antenna con-nector by wrapping it into tape .12
D
Fig. 9
D12
3.a) Tuck the RDS-antenna wire through
the space between the roof headlinerand windshield.
b) Route and attach the RDS-antennawire along the vehicle wire harness
using wire ties (3x) (*) and tape(2x) (*).
(*) Included in the navigation kit.
121513
D
D
Fig. 10
Be sure to attach the RDS-antennawire as far as possible against theborder of the roof headliner.
CAUTION
For vehicles without prewired ETA-antenna
D
12
13
(*)
15 (*)
Corolla Verso (RHD) - 11 02-04
Corolla Verso (R1) ELECTRONIC TRAFFIC AVOIDANCE
4. Route and attach the RDS-antennawire down the instrument panel intothe left kick panel section of the vehi-cle. Use 4 wire ties (*).
(*) Included in the navigation kit.
15
D
Fig. 11
5.a) Route the antenna wire along the
front scuff plate area under the carpet(along the cross member ) to thenavigation-ECU location .
b) Attach the antenna wire to the vehi-cle wire harness using wire ties (3x)(*).
c) Bundle up the excess antenna wireunder the carpet.
(*) Included in the navigation kit.
15D
1916
D
Fig. 12
6. Route and attach the ground wireusing a bolt as shown.
: Bolt (M6x10) (1x)105
105
Fig. 13
105
Ground wire
D
D
16
19
(*)15
15
D
(*)
Excess wire
Corolla Verso (RHD) - 1202-04
Corolla Verso (R1) ELECTRONIC TRAFFIC AVOIDANCE
INSTALLATION OF THE RDS-ANTENNA STRIP
Fig. 14
70 mm 20 mm
Coated area
1.a) Thoroughly clean the mounting sur-
face of the front window to which theantenna strip is to be affixed.
b) Remove the release paper of theantenna strip .
c) Attach the antenna strip to the frontwindow as shown. Ensure that the an-tenna strip is attached horizontally.6
6
6
6
Centre
Fig. 15
2. Peel off the release paper at the backof the RDS-antenna and attach it tothe coated area of the antenna strip
as shown.6
D
ONLY FOR VEHICLES WITH RAIN SENSOR
Ensure that the top of the antenna ispushed against the body of the roof.
CAUTION
6
D
6
Fig. 16
D
D
Centre
Centre
6
3. Peel off the release paper at the backof the RDS-antenna and attach it tothe coated area of the antenna strip
as shown.6
D
FOR VEHICLES WITHOUT RAIN SENSOR
Ensure that the top of the antenna ispushed against the body of the roof.
CAUTION
For vehicles without prewired ETA-antenna
Corolla Verso (RHD) - 13 02-04
Corolla Verso (R1) ELECTRONIC TRAFFIC AVOIDANCE
INSTALLATION OF THE RDS-TUNER
FOR INSTALLATION OF NAVIGATION, PLEASE REFER TO THE NAVIGATION INSTALLATION MANUALAIM 000 071-0.
1. Fit the RDS-tuner to the RH sidebracket using bolts .
: Bolt (M5x8) (2x) c
ca
1
Fig. 17
Make sure that the RDS-tuner isinstalled at the lowest position.
1
CAUTION
c
1
a
2.a) Connect the 1P and 8P connector of
the navigation harness to the naviga-tion ECU .
b) Connect the navigation 13P femaleconnector to the RDS-subwire harness
13P male connector.c) Connect the RDS-subwire harness
13P female connector to the naviga-tion ECU .19
22
19
Fig. 18
19
Navigation harness2
3.a) Connect the RDS-antenna black wired
pin to the RDS-subwire harness 12P connector to the second positionfrom the left on the top row (wires faceyou and tab is on top).
b) Connect the RDS-subwire harness 12P connector to the RDS-tuner .1
2
2
Fig. 19
1
Black wired pin
WIRE SIDE VIEW
12P2
For vehicles without prewired ETA-antenna
Corolla Verso (RHD) - 1402-04
Corolla Verso (R1) ELECTRONIC TRAFFIC AVOIDANCE
5. Fold the carpet and fit the navigationECU with the RDS-tuner on thefloor as shown using bolts .
: Bolt (M8x12) (2x) d
d
119
4.a) Connect the RDS-antenna connector
to the fakra connector as shown.
b) Insert the fakra connector withantenna to the RDS-tuner .1D
5
5D
Fig. 20
Be careful not to close the fakra con-nector before the RDS-antennaconnector is inserted till it clicks.D
5
CAUTION
Turn
1D
D 5
5
Fig. 21
19
d
d 1
Use foam tape to mask the RDS-tuner from view and place itbetween the floor and the RDS-tuner
for protection of the seat-wire har-ness.
1
1
e
CAUTION
e
Corolla Verso (RHD) - 15 02-04
1. a) Release the navigation ECU from
the vehicle.b) Fit the RDS-tuner to the ETA-
bracket using the bolts .: Bolt (M5x8) (2x)
c) Fit the RDS-tuner between thecross member and the navigation ECUas shown. Use butyl tape to attachthe RDS-unit to the navigation ECU.
d) Place foam tape to protect the lowercorners of the RDS-tuner as to pro-tect the wire harness.
1
e
f
1
c
c7
1
19
Corolla Verso (R1) ELECTRONIC TRAFFIC AVOIDANCE
For vehicles with prewired ETA-antenna
Fig. 22
f
19
7
1c
e
2.a) Connect the 13P and 8P connector of
the navigation harness to the naviga-tion ECU .
b) Connect the navigation 13P femaleconnector to the RDS-subwire harness
13P male connector.c) Connect the RDS-subwire harness
13P female connector to the naviga-tion ECU .
d) Connect the RDS-antenna black wiredpin to the RDS-subwire harness 12P connector to the second positionfrom the left on the top row (wires faceyou and tab is on top).
e) Connect the RDS-subwire harness 12P connector to the RDS-tuner .
f) Insert the RDS-antenna connector in the fakra connector as shown.
g) Connect the fakra connector withantenna to the RDS-tuner .1D
5
5
D
1
2
2
19
2
2
19
Be careful not to close the fakra con-nector before the RDS-antennaconnector is inserted till it clicks.D
5
CAUTION
Fig. 23
D
1
5
2
D
WIRE SIDE VIEW
12P
2
195
Corolla Verso (RHD) - 1602-04
Corolla Verso (R1) ELECTRONIC TRAFFIC AVOIDANCE
Fig. 24
3. Refit the navigation ECU .19
D
5 19
12
AFTER INSTALLATION AND FUNCTION CHECK, BE CERTAIN TO RE-FIT PANELSAND CONNECTORS CORRECTLY AND TIGHTEN ALL BOLTS TO THE SPECIFIED