Installation Instructions For 2011-13 Chrysler 300/Dodge … Car.pdf · 2020-01-17 · Installation Instructions For 2011-13 Chrysler 300/Dodge Challenger/Charger/Durango 3.6 2011-14

Hypertech’s new product, the Interceptor, is asmart technology design that works with today’sgeneration of complex engine computers.The Interceptor easily mounts under the hood of avehicle and plugs into the factory connectorsto constantly monitor the vehicle’s functions.It then automatically recalculates the factory’scomputer performance calibrations with legendaryHypertech Power Tuning. This means morehorsepower and torque, quicker acceleration, betterdriveability, and improved MPG.

The Interceptor Controller easily installs under thehood in about fifteen (15) minutes. The InterceptorAccelerator Pedal Controller installs in the vehicle’sinterior on the driver’s side above the acceleratorpedal in about (15) minutes.

BEFORE installing the Hypertech Interceptor:Make sure the vehicle engine and ignition is turnedOFF prior to beginning the installation.

MAP Sensor(3-Pin)

Cam Sensor(4-Pin)

Intake AirTemp Sensor

(2-Pin)

NOTE: Sensor locations may vary slightly depending on the application.

Underhood sensor locations for installing the Hypertech™ Interceptor™

Tools needed for Interceptor installation:• Flashlight

Step-By-StepInstallation InstructionsFor 2011-13 Chrysler 300/Dodge Challenger/Charger/Durango 3.6 2011-14 Jeep Grand Cherokee 3.6 - Part #705007

CAREFULLY lift off the engine cover to avoid scratching it onsurrounding surfaces and place it to the side while installing theHypertech Interceptor.

Installing the Hypertech Interceptor Controller (3.6 Car)

Locate fuse box in the engine compartment on the passenger side.Press the locking tabs to disengage fuse box and lift up to expose emptycompartment. Locking tabs may vary slightly from those shown above.

Before proceeding to the next three (3) installation sections, lay out theInterceptor harness in the general areas of the sensor locations as shownin the engine compartment photo on page 1.

2

InterceptorController

FuseBox

Place Interceptor Controller on its side in the compartment,making sure no cables are pinched or bent. Then re-install the fusebox back to its original location.

Installing the Hypertech Interceptor Controller (3.6 SUV)

InterceptorCable

Route the Interceptor cable between the fuse box and passengerside strut tower.

InterceptorCable

Connecting the 4-Pin Cam Sensor

Locate the cam sensor near the transmission fill tube on the passenger side.

TransmissionFill Tube

Cam Sensor

Locate fuse box in the engine compartment on the passenger side.Press the four (4) locking tabs (2 on each side) to disengage fuse boxand lift up to expose empty compartment. Locking tabs may varyslightly from those shown above.

LockingTabs

(2 eachside)

Place Interceptor Controller on its side in the compartment,making sure no cables are pinched or bent. Then re-install the fusebox back to its original location.

InterceptorController

FuseBox

InterceptorCable

Connecting the 2-Pin Intake Air Temp Sensor

3Disconnect the factory connector from the 2-Pin (intake air temp) sensor.

Intake AirTemp Sensor

Plug the Interceptor 4-Pin cam sensor connector into the vehiclecam sensor.

Interceptor 4-PinCam Harness

Connector

Factory 4-PinConnector

NOTE: Ensure that the Interceptor harness and all connectors are clear frommoving and/or rotating parts of the engine as well as any extreme heat sources.

Connecting the 4-Pin Cam Sensor (Cont’d)

Interceptor 4-PinCam SensorConnector

Cam Sensor

Plug the Interceptor 4-Pin cam harness connector into the factorywiring harness 4-Pin connector.

TransmissionFill Tube

Connecting the 2-Pin Intake Air Temp Sensor (Cont’d)

Route the Interceptor harness and plug the Interceptor 2-Pinconnector into the vehicle intake air temp sensor. NOTE: The correctorientation of the connector is shown above.

Interceptor 2-PinConnector

Plug the Interceptor harness 2-Pin connector into the factory wiringharness 2-Pin connector. NOTE: The correct orientation of the connectoris shown above.

NOTE: Ensure that the Interceptor harness and all connectors are clearfrom moving and/or rotating parts of the engine as well as any extremeheat sources.

Interceptor 2-PinHarness Connector

Disconnect the factory connector for the 3-Pin (MAP) sensor.This connector has a locking clip that must be slid back to unlock.Then, squeeze down the locking tab, and push the connector inslightly (toward sensor) and then remove.

Connecting the 3-Pin MAP Sensor

Disconnect the factory connector from the 4-Pin cam sensor.This connector MAY have a locking clip that must be slid back tounlock. Notice the slight difference in the position when the tab is inthe “UNLOCKED” position. Then, squeeze down the locking tab,and push the connector in slightly (toward sensor) and then remove.

Locked Position Unlocked Position

Red isVisible

Red notVisible

Front OfVehicle

Product WarrantyFactory Direct Limited Lifetime Warranty

PRODUCT WARRANTY Factory Direct Limited 1 Year Warranty.. Effective January 1, 2020 replaces and supersedes previous product warranty policy.

Hypertech products are warranted against defects in materials or workmanship for one year from the date of purchase. Hypertech’s liability under this warranty shall be limited to the prompt correction or replacement of any defective part of the product which HYPERTECH determines to be necessary. This Limited 1 Year Warranty is to the original purchaser providing all the information requested is furnished. You must retain a copy of your original sales invoice or receipt. Without proper documentation, a service fee will be applied. Third Party Resellers and Resold units are NOT covered under this warranty.

For more information, go to www.hypertech.com

3215 Appling Road • Bartlett, Tennessee 38133-3999Office Hours: 8am-5pm, Central Time, Mon.-Fri.

Tech: 901.382.8888 • Business: 901.385.1888 • Fax: 901.373.5290 Part #9397.13

© 2013 Hypertech, Inc.

Using a flashlight, locate the factory accelerator harness connectorunder the driver’s dashboard and above the accelerator pedal.Push the carpeted compartment cover out of the way so you candisconnect the factory harness from the accelerator pedal sensor.

Connecting the Interceptor Accelerator Controller

FactoryAccelerator

HarnessConnector

(Behind Carpet)

Plug the Interceptor accelerator pedal sensor connector into thefactory accelerator pedal sensor.

InterceptorAccelerator

Pedal SensorConnector

FactoryAccelerator

Pedal Sensor

Plug the Interceptor accelerator pedal harness connector into thevehicle’s factory accelerator pedal sensor connector.

Factory AcceleratorPedal Sensor

Connector

InterceptorAccelerator

Pedal HarnessConnector

Connecting the Interceptor Accelerator Controller (Cont’d)

Tuck the Interceptor accelerator controller behind the carpet and out ofthe way. You may secure it using a zip tie. Installation is now complete!You are now ready to enjoy more power and performance with theHypertech Interceptor!

NOTE: Ensure that the Interceptor harness and all connectors are clearfrom moving and/or rotating parts of the engine as well as any extremeheat sources.

Plug the Interceptor 3-Pin connector into the vehicle MAP sensor.

Plug the Interceptor harness connector into the factory 3-PinMAP sensor wiring harness connector. NOTE: The correct orientationof the connector is shown above.

Factory 3-PInConnector

Connecting the 3-Pin MAP Sensor

Interceptor 3-PinConnector

MAP Sensor