INSTALLATION GUIDELINES PRODUCT DISCRIPTION ......INSTALLATION GUIDELINES MAINTENANCE PRODUCT DISCRIPTION WARNING!!! We decline all responsibility and eventual inaccuracy contained

INSTALLATION GUIDELINESMAINTENANCEPRODUCT DISCRIPTION

WARNING!!!

We decline all responsibility and eventual inaccuracy contained in the instructions due to transcript errors.

Antonio Lupi Design S.p.A. provides screws and plugs with each furniture yet the installer should verify case by case if they are suitable for the installation. We will not be held responsible for any damage caused by the mounting of our units.

We will not respond to eventual swelling in the wood when caused from negligence or when the furniture is left in contact with water for a long period of time.

We invite our clientele to thoroughly inspect all material received prior to installation.

3,4 cm 4,4 cm 4,4 cm 3,4 cm

3,4 cm

Piana collection

ASSEMBLY FOR WALL HUNG FURNITURE

1. Arrange the furniture on the fl oor prior to installation.

3. Measurements to fi x support platelets to the wall

5. Hook the furniture.

2. Assemble the furniture together with the screws provided.

4. Fix the support platelets.

Antonio Lupi Design Page 2

22 mm

19 mm

6-7. Fasten the unit to the wall and tighten the screws regulating in height or spacing the furniture from the wall

9. Level the composition

8. Insert and secure the front panel

Piana collection



ASSEMBLY AND DRAIN POSITION DIAGRAM

TOPS WITH INTEGRAL SINKS AND FOR UNDER-MOUNT SINKS TOP MOUNT SINKS

Panta Rei collection

With tradional siphon - Only for 50 H With tradional siphon - Only for 50 H

registered model and design


Panta Rei / Planeta collection

1. Positioning and levelling of furniture to the wall

3. Fixing of furniture bracket to wall (provided only on request)

5. When completed apply non acidic silicone between the top and the wall

2. Hanging of wall support plates

4. Positioning and silicone of sink with non acidic silicone

SPEC SHEET WITH WOOD TOP



22 mm

19 mm

1. Positioning and levelling of furniture to the wall

3. Fixing of furniture bracket to wall (provided only on request)

5. Positioning and silicone of sink with non acidic silicone

2. Hanging of wall support plates

4. Silicone top with non acidic silicone

6. When completed we advise to apply non acidic silicone between the top and the wall

Panta Rei / Planeta collection

SPEC SHEET WITH GLASS TOP



4,2 cm

3,4 cm

2,2 cm2,2 cm

22 mm

19 mm


1. Measurements to fi x support platelets to the wall

3. Hook the furniture.

2. Fix the support platelets.

4-5. Fasten the unit to the wall and tighten the screws regulating in height or spacing the furniture from the wall

Panta Rei collectionregistered model and design


ASSEMBLY AND DRAIN POSITION DIAGRAM

Materia - collection

Furniture 25 cm H. Furniture 25 cm H.

Furniture 50 cm H. Furniture 50 cm H.

Suspended tops Suspended tops

DRAIN DIAGRAM FOR TOPS WITH INTEGRAL SINKS AND FOR UNDER-MOUNT SINKS



DRAIN DIAGRAM FOR TOP MOUNT SINKS




1. Lay furniture side by side in order before assembling

3. Drill holes in sides with an 8 mm diam. wood tip to subsequently assemble together.After having drilled the sides in order to combine furniture, remove waste through blow to avoid dust settles on glides of drawers.

5. Assemble the furniture together with screws provided

2. Lay furniture side by side in order before assembling

4. Assemble the furniture together with screws provided

6. Totally unscrew the wall hook so as to clasp the furniture to the plate

Materia collection

FURNITURE ASSEMBLY DIAGRAM

32 cm. deep 54 cm. deep

32 cm. deep

54 cm. deep


22 mm

19 mm

Materia collection

FURNITURE ASSEMBLY DIAGRAM

7 . Use the top screw to regulate the furniture in height. From inside the furniture use the bottom screw for tightening

8. Position and level the composition


13. Rest the under-mount sink on the internal regulating brackets

15. Silicone the top and the sink with non acidic silicone

Materia collection

UNDERMOUNT SINK ASSEMBLY

14. Level the sink using the regulating brackets and position in the center of the cabinet



17. Silicone the top with non acidic silicone

19. Silicone and position the sink with non acidic silicone

Materia collection

TOP MOUNT SINK ASSEMBLY

18. Position top



Aero collection

UNDER-MOUNT AERO INSTALLATION DIAGRAM

TO INSTALL THE “AERO” WALL SUPPORTS PROCEED AS FOLLOWS:

•To determine the position of the wall brackets fi rst calculate the exact fi nal height of the composition by adding the various heights from the fl oor and subtracting the thickness of the glass and the fi xed amount of 9,8 cms. to bore the superior hole 1A. Bore a second hole vertically at 12,5 cms. 2A (Fig. 1).

• To determine the horizontal position of the brackets measure the distance between the two holes “I” of the towel rod (Fig.2).

• Fit the dowels A into holes 1A and 2A (Fig. 1).

• Screw, not completely, the screws B into the dowels A, leaving them 2 mm out from the wall (Fig. 1).

• Slide the brackets on the wall anchoring to screws B and fi x with screws C in holes 1A and screw bosses D (Fig. 1).

• Position the top on the brackets and level utilizing the 4 regulating washers E. Mark the holes for the L-bracket F onthe wall,remove the top and fi x the bracket. (Fig. 3).

• Re-position the top on the brackets and seal with the non-acidic silicone provided, once fi xed position the undermount sink on the 4 registers under the top and seal with the non-acidic silicone provided.

• Fix the alluminum cover G to the top with screws provided (Fig. 3).

• Fix the towel rod to the brackets with the screws provided H (Fig. 1).

P.S. USE EXCLUSIVELY NON ACIDIC SILICONE


Aero collection

TOP MOUNT AERO INSTALLATION DIAGRAM

TO INSTALL THE “AERO” WALL BRACKETS PROCEED AS FOLLOWS:

• To determine the position of the wall brackets fi rst calculate the exact fi nal height of the composition by adding the va-rious heights from the fl oor and subtracting the height of the sink, the thickness of the glass and the fi xed amount of 9,8 cms. to bore the superior hole 1A. Bore a second hole vertically at 12,5 cms. 2A (Fig. 1).

• To determine the horizontal position of the brackets measure the distance between the two holes “I” of the towel rod (Fig. 2).



• Slide the brackets on the wall anchoring to screws B and fi x with screws C in holes 1A and screw bosses D (Fig. 1).

• Position the top on the brackets and level utilizing the 4 regulating washers E and fi x with the non acidic silicone provided (Fig. 1) once fi xed position the top mount sink and seal with the non-acidic silicone provided.




INTEGRATED AERO INSTALLATION DIAGRAM

TO INSTALL THE “AERO” WALL BRACKETS PROCEED AS FOLLOWS:

• To determine the position of the wall brackets fi rst calculate the exact fi nal height of the composition by adding the various heights from the fl oor and subtracting the thickness of the glass and the fi xed amount of 9,8 cms. to bore the superior hole 1A. Bore a second hole vertically at 12,5 cms. 2A (Fig. 1).

• To determine the horizontal position of the brackets measure the distance between the two holes “I” of the towel rod (Fig.2).



• Slide the brackets on the wall anchoring to screws B and fi x with screws C in holes 1A and screw bosses D (Fig. 1).•Posizionare il top e metterlo a livella tramite i 4 distanziali regolabili E (Fig.1), fi ssandolo con silicone.

• Riposizionare il top sulle staffe, fi ssandolo con silicone. Una volta fi ssato il top fi ssare il lavabo sottopiano con l’apposito silicone in dotazione e tramite le 4 staffe di fi ssaggio poste sotto al top.

• Position the top on the brackets and level utilizing the 4 regulating washers E and fi x with the non acidic silicone provided.



Aero collection


1

3

2

INSTALLATION INSTRUCTIONS FOR Art. HOUDINI

1. Loosen the screws from the bracket and slide it to one side as shown so as to position the glass in between.

3. Rest up against the wall and hold until fi xed.

2. Block the glass and tighten the screws..

4. Fix bracket (A) to the wall so as to obtain a completely level surface.

Registered model and design


1

3

5 6

2

INSTALLATION INSTRUCTIONS FOR Art. BANCO


TECHNICAL DIAGRAMS

1. Open the crate from the indicated side “ lato da aprire “ ( A )

2. Take the top out of the top by grasping where the arrows indicate.


TOP

WARNING!Check the integrity of the top prior to assembly. The top must be handled and stored on its side during the installation of it on the furniture.


Traditional installation with hinges 200 Series

HINGE ADJUSTMENT

Fast installation with hinges DOMI®

1. Install the hinge on the cabinet and position.

2. Tighten the fi xing screw.

3. Once fi nished, between the door and the side of the cabinet the gap should measure 0,7 mm.

4. Security hook.

P.S. OUR DOORS HAVE A SHOCK ABSORBER CLOSING MECHANISM. DO NOT BANG THE DOOR AND DO NOT FORCE THE CLOSURE IN ORDER TO AVOID THE BREAKAGE OF THE MECHANISM.

5. Bring the two ppoints indicated with the arrow near eachother.

6. Slightly rotate.

7. Apply a light pressure.

8. To un-hook push on the point indicated with the arrow.


FRONT ADJUSTMENT

1. Front adjustment: It is possible to adjust a door front from - 0,5 mm to + 2,8 mm through an eccentric screw without having to loosen any screw.

2. Vertical adjustment: It is possible to adjust vertically the door front + 2 mm through an eccentric screw without having to loosen any screw.

3. Adjust laterally: the hinge using the indicated screw and with the same screw it is possible to fi nd the beginning value of “L” = 0,7 mm.

P.S. OUR DOORS HAVE A SHOCK ABSORBER CLOSING MECHANISM. DO NOT BANG THE DOOR AND DO NOT FORCE THE CLOSURE IN ORDER TO AVOID THE BREAKAGE OF THE MECHANISM.


Assembly, removal and adjustment

BLUM DRAWER ADJUSTMENT

1. Drawer

3. Drawer insertion and removal.

5. Height - Tilt adjustment

2. High fronted pull-out

4. Side adjustment.

Assembly

Removal

Removal

Insertion

Height adjustment +/- 2 mm

Front assembly Back assembly

Back removal Front removal

Side adjustment: to the right 1 mm

Side adjustment:to the left 1 mm


REGULATION FOR FLAP FRONT






Just

1. Fixing plug Ø 8x40 with screw Ø 4 x 70 mm.


3. Plate for wall fi xing.

4. “Just” wall support.

5. Screw Ø 2 mm.

6. Key for fi xing included.

INSTALLATION INSTRUCTIONS FOR “JUST - TAPE” ACCESSORIES WALL SUPPORT

Just


2. “Tape” wall support.

Just Tape


Tenso

1. Dowell with stud.

2. For showroom use only insertion to replace dowell

3. Wall support

4. Stainless steel cylinder for wire blockage

5. Stainless steel spring

6. Stainless steel knurled cylinder.

INSTALLATION INSTRUCTIONS FOR ART. TENSO

Tenso

Tenso/S

1. Stainless steel insertion for Paco leg

2. Stainless steel cylinder for wire blockage

3. Stainless steel spring

4. Stainless steel knurled cylinder

5. Stainless steel wire

Tenso/S


WARNINGbefore drilling a hole in the fl oor, measure the distance between the two legs, making sure that the internal measurement under the top is the same.

1. Drill the fl oor using a 6cm. diam tip, insert the dowell (Fig.E) position the plastic washer (Fig.D) on top of the steel washer (Fig.C).

2. Tighten screws and position the leg (Fig.B)

INSTRUCTIONS FOR BLOCKING ART. PACO, BASIC1, BASIC2

P.S. FOR SHOWROOM USE ONLY, IT IS POSSIBLE TO GLUE, WITH SILICONE, THE PLASTIC WASHER (FIG.D) AVOI-DING TO DRILL A HOLE IN THE FLOOR.

Leg Art. PACO/BASIC

Screw

Steel washer

Plastic washer

Dowell


NEON

UP IP21

LED

UP IP21

MIRROR MOUNTING DIAGRAM

1. To fix the mirror to the wall at the desired height A insert brackets S under frame B. Measure the distance H between the superior border of the mirror and the bending point of the wall support

3. Take off the corner protection only after the mirror is mounted on the wall

NB. TAKE OFF THE CORNER PROTECTION ONLY AFTER THE MIRROR IS MOUNTED ON THE WALL

2. Fix the brackets S to the wall with the bending point at height C (C=A-H)

5 cm ? 5 cm

s s

B BH

CA


LED

UP IP21

CUPIDO MIRROR MOUNTING DIAGRAM

1. art. CUPIDO72 2. art. CUPIDO125


ZONA 2IP24

ZONA 3IP21 ZONA 1

60 cm

REGULATIONS

The drawing above illustrates an example of an electrical installation in a bathroom complete with water heater, bathtub and shower so as to install our mirrors according to code IEC 529. The wiring of our mirrors complete with lighting have an IP21 protection grade. In order to comply with this code our mirrors must be installed in ZONE 3 at least 60 cm away from the border of the bathtub, shower or water heater.MPORTANT The mirrors are equipped with hard plastic corner protectors to be removed only after being installed on the wall (they are intended to protect the corners from minor impacts).

The lighting fi xture must be installed only by qualifi ed technicians and used only for the purpose for which it was designed and in respect of maintenance instructions. The replacement of all parts must be performed by qualifi ed personnel only, respecting the relevant laws in force and making using original material. In case of doubt or defect contact your retailer. Immediately replace defective glass and bulbs. Keep instructions for maintenance purposes. The CE symbol indicates conformity of 2006/95/CE-2004/108 2011/65/EU-RoSH2.

Packing materials may constitute a hazard (risk of suffocation, abrasion, etc.) and must not be left within reach of children.

LED (IEC 62471)

RG0-RG1For LED devices use only bulbs with photo biological risk class RGO (exempt) or RG1 (negligible)

The defi nition of the symbols: 1 Use self-shielded bulbs only - 2 Avoid fi re risk and excess UV radiation do not use bulbs identifi ed for use in closed devices.

For shielded devices (e.g. R7s caps). The lights must be complete with protective glass; “Replace the glass immediately if it cracks or otherwise deteriorates” with original parts.

The light source contained in this device is not user replaceable and can only be replaced by the manufacturer or his service agent or a similar qualifi ed person.

Device with type Y attachment cord: if the cord is damaged, the replacement can only be made by the manufacturer or similar qualifi ed person and original parts of the manufacturer.

INSTALLATION INSTRUCTIONS - Disconnect the power supply. Mount the fi xture based on the drawing following the respective numbering. Use bulbs with correct wattage indicated on the label.

With this symbol use a protection tube on the cable resistant to 180°C and 4kV.

UP Install observing the direction.

With this symbol the bulb cannot be replaced with energy saving bulbs.

If the power terminal block is not mounted: The installation may require the involvement of qualifi ed personnel with the terminal block box certifi cate.

1 Tighten the single wiring to the terminals 6 mm long and peel 6 mm; 2 Completely cover the wires from the wall with he tube; 3 Close the box on the double insulation of the wiring. Do not use cables with metal coverage.

IP21 IP40IP43 IP54 IP**= Device protected against: IP21=Drip proof, IP40= 1mm probe-proof (IEC1032), IP43=rain proof (water at 60°), IP54= dust & splash proof.


1. Glitter lamp mounting

3. A1 lamp mounting

5. A6 lamp mounting

2. Glitter bulb replacement

4. A1 bulb replacement

6. A6 bulb replacement

Protection IP21

LAMP MOUNTING DIAGRAM


EXIT/FILO

IP21

LIGHT1/LIGHT2/ LIGHT3

IP21

Protection IP21

LAMP MOUNTING DIAGRAM

7. Exit/Filo lamp mounting

9. Light1/Light2 lamp mounting

8. Exit/Filo bulb replacement

10. Light1/Light2 bulb replacement


INSTALLATION INSTRUCTIONS ART. LIGHT1 LIGHT2 LIGHT3

Installation

• Loosen the plate which holds the glass A by unscrewing the screws B• Insert glass C of the lamp as in Fig.2 with little force. The glass installation is verifi ed with each lamp by our operators, if it is not possible to insert easily the glass from one end we suggesttrying from the other.• Position the glass as in Fig. 1• Tighten the screws B to block the plate A

WARNING:

Do not overly tighten the plate because too much pressure between glass and metal could cause breakage to the glass.ELECTRICAL INSTALLATION• Connect the wires C in a phase of the electrical installation• Connect the wires D in the other phase of the electrical installation• Connect the green/yellow wire E to the land electrical installation


INSTALLATION INSTRUCTIONS ART. LIGHT3 ON ART. REGOLO AND RIFLESSO

Installation

Fix the light to the wall cabinet and make sure the wires fi t into the groove.

Screw the cover (A) to the groove.

Connect the wires to the electrical outlet.


1. Vulcano lamp

Light bulb replacement

• Un-plug the lamp from the socket• Un-screw 1,2,3 and remove structure (Fig.1)• Replace light bulb• Replace structure and screw 1,2,3 (Fig.1)

3. Assembly Spot1/C - Spot1/T - Spot2/C - Spot2/T - Disco/C - Disco/T

ASSEMBLY AND REPLACEMENT INSTRUCTIONS FOR BULB

1. Spot - Disco lamp

Light bulb replacement

• Un-plug the lamp from the socket• Un-screw A and remove the cover (Fig.1)• Un-screw 1,2,3 and remove structure (Fig.1)• Replace light bulb• Replace structure and screw 1,2,3 (Fig.1)• Replace cover and screw A

4. Montaggio lampade Spot1/C - Spot1/T - Spot2/C - Spot2/T Disco/C - Disco/T

Fig.1: Bottom view Fig.1: Bottom view

2

1


INSTRUCTIONS FOR SANITARY INSULATOR

• HELPFUL HINTS FOR AN EASY INSTALLATION To fi x the watercloset to the wall use a “T” handle wrench with swivelling hexagon socket ø 17 mm.

• Position the insulator to the wall so it corresponds to the supports and drainage.

• Fix the sanitary to the wall

• Eliminate the excess parts of the insulator by cutting around the sanitary.


1. Mount the supports for suspended WC with plugs distance one from another (inter-axis) of 18 cms.

3. Before fi xing WC check that the nut is screwing perfectly on the plug. The conic part has to be addressed to the wall.

5. First insert the rectangular plaque and then the nut in the plug

SCHEMA DI MONTAGGIO SANITARI Art. SELLA1- SELLA2

2. Make sure that the plugs are coming out 15 cms. from the wall.

4. Insert WC in the plugs using the provided wooden piece of 18,5 cms thick in order to support it.

6. Tighten the nuts with a wrench Ø 17


7. Wrench ø17 ( not provided) 8. Plug with thread bar ø10 included. Use only for fl oor mounted WC or display installations.


The seat is made from the fi nest thermosetting material which is extremely resistant and durable.The smooth and compact surface allows the seat to be easily cleanedwith a cloth and normal non-abrasive liquid detergent.The stainless steel hinge allows the seat to be removed easily for a more thorough cleaning.

IMPORTANT: when cleaning the toilet bowl with descaling products, do not leave them to act with the lid closed because these products release gas which attacks any type of stainless steel materials (both AISI 304 and AISI 316). Therefore, leave the lid OPEN when using these detergents (even if aggressive and non-standard), so that the hinge remains shiny over time. Only close the lid when the action of the products has fi nished and after fl ushing.

INSTRUCTIONS FOR THE THERMOSETTING SEAT WITH SLOW-CLOSEHINGE - FOR ART. ABOL - CUPOLA - MASCOLO

1. Fixing kit.

3. Make sure the bushes A-B are completely inserted into the holes M present on the bowl lid. Insert the lid into the previously mounted hinges. ATTENTION: make sure the ring and lid are united during this operation.

2. Insert the hinges into the holes H, tilting the fasteners F so that they pass through the holes. Fasten the hinges by pulling the end of the screw D upwards so that the fastener F comes into contact with the inside of the bowl. At the same time, turn in a clockwise direction.

4. Lower the lid and centre it over the toilet.


INSTRUCTIONS FOR THE THERMOSETTING SEAT WITH SLOW-CLOSEHINGE - FOR ART. ABOL - CUPOLA - MASCOLO

5. Block the hinges on the ceramic bowl by using a wrench to tighten the screw D, after which insert the small cover C and press down. Lift the bowl lid and block it partially at the two uiding columns by manually tightening the small wheel I. ATTENTION: do not block it completely. Open and reclose the lid to check the closing speed. If one of the two bowl-lid elements drops too quickly or too slowly, proceed as follows.

7. Remove the bowl-lid by loosening the small wheels I again. Before adjusting the speed, it is important to know that only the serrated holes act as a brake. As shown in the fi gure, one is positioned next to the lid and the other on the ring. To adjust, work on the hinge inserted in the serra ted hole of the ring or lid. Position the toilet bowllid upsi de down on a surface and use the wrench L supplied with the kit on the element (lid or ring) that needs adjusting. Insert the wrench into the hole of the hinge, as shown in the fi gure. Turn the wrench in a clockwise direction for a slower closing (of the ring or lid), otherwise in a counter clockwise direction for a faster closing (of the ring or lid).

ATTENTION: the wrench must only move a few millimetres (ei-ther clockwise or counter clockwise).

6. To speed up the mechanism of the seat cover slide it off the w.c. in the open position (fi g. A) and follow the instructions in point 7. To slow down the mechanism of the seat cover slide it off the w.c. in the closed position (fi g.B) and follow the instructions in point 7.

To speed up the mechanism To speed up the mechanism


INSTRUCTIONS FOR THE THERMOSETTING SEAT WITH SLOW-CLOSE HINGE - FOR ART. ABOL - CUPOLA - MASCOLO

8. ATTENTION: before reinserting the bowl lid onto the toilet, realign the holes of the hinges which were moved during the adjustment. Slip off the hinge which was adjusted (ring or lid) and reposition, making sure the holes of the two hinges are aligned (as shown in the fi gure).

9. Rieposition the bowl lid, manually tighten the small wheels I and check the closing speed again. If the speed is correct, fasten the hinges to the columns using a hexagon wrench. If more adjustments need to be made, repeat the operations described in point 6.


NO!

OK

INSTRUCTIONS FOR THE THERMOSETTING SEAT WITH SLOW-CLOSE HINGE FOR ART. SELLA / EVAKUO / KOMODO

Precautions for long-lasting surface quality of seats hand hinges

Clean with a soft sponge or cloth.Make use of detergents commonly used for the home and avoid the use of steel wool and or products that contain acid, chlorine, ammonia, and are corrosive or abrasive.

CAUTION: if using specifi c products or which has a prolonged effect to clean ceramic avoid contact with the seat cover and hinges. If this should happen immediately rinse out thoroughly. Do not lower the seat or cover to avoid exposure to fumes which could alter the colour.


INSTALLATION INSTRUCTIONS ART. SPLINE

1. Position the back rest making sure that the slit on the back side fi ts precisely on the internal border of the bathtub and center . Mark the position of the stopper on the upper fl at side of the border of the bathtub as shown.

3. Remove the protection from the double stick tape and apply a small amount of silicone on the its back side. Position where previously marked.

2. Remove the stopper from the back rest following the arrows in fi gure 2.

4. Give the silicone time to adhere after which you may reposition the back rest.


L =

100 < 40 mmm

DRAIN MOUNTING DIAGRAM

WARNING: Use exclusively the products supplied.

SUGGESTIONS FOR THE INSTALLER:

• Use all the elements equipped as illustrated in the diagram being careful not to excessively tighten the drain to the top. A bad installation may cause breakage even after time.

Plug

Drain

Sponge trimming

Top

Silicone trimming

Special drainpipe fi tting

Key for tightening


L =

100 < 40 mmm




Drain stopper

Sink fl ange

Fange gasket

Sink

Flange washer

Flange washer

Tailpiece

Drain key

Mounting ring

Top

Not supplied with Art.:PILA, PILA1, URNA.

DRAIN INSTALLATION INSTRUCTIONS FOR SINKART. BUBBLE - MIMO1 - MIMO2 - MIMO3 - MIMO4 - PILA - PILA1 - URNA


L =

100 < 40 mmm

STAINLESS STEEL PLATE INSTALLATION DRAWING FOR TEMPORARY USAGE

THESE INSTRUCTIONS ARE ONLY VALID FOR SHOWROOM USE.




Sink fl ange

Small fl ange washer

Sink

Big fl ange washer

Tailpiece

Top

“Butterfl y” stainless steel plate


TECHNICAL DRAWING FOR BATH TUB DRAIN WITH PRESSURE PLUG

In order to proceed with the ispection of the waste remove the plug.




ONLY FOR BATH

Cristalplant:BaìaSartoriale

Pietra:ArcaBaìaBomberCover

Flange washer

Sink fl ange

Drain stopper

Flange washer


In order to proceed with the ispection of the waste remove the plug A.




Flange washer

Flange washer

Drain stopper

Sink fl ange

TECHNICAL DRAWING FOR SHOWER TRAY DRAINART. 013/013combi - 039/039combi - 0X/0Xcombi - SLAB


The seal of the waste ring (1) is granted by tightening the 4 screws.The screws must not be forced during the tightening.The threaded ring (2) must no be positioned out of the threaded seat of the waste (fi g. a)Use exclusively the products supplied.

TECHNICAL DRAWING FOR SHOWER TRAY DRAIN ART. 00


All glass utilized for the shower cabins are 8 mm clear tempered glass, these are made 2,5 cms. shorter than the complete length of the shower tray (fi g A and B). The wall connectors and hinges are in stainless steel.Antonio Lupi Design S.p.A. advises installation as shown below in drawing C in order to avoid as many mistakes as possible. Considering a tile coating of more or less 1 cm in thickness if installed as in drawing D please always give exact measurements of the shower and eventually any uneveness in the walls or fl ooring. Follow the instructions below for proper measuring:

• High light any uneveness of the walls with respect to the fl ooring or between two walls if in a recessed area• Indicate eventual uneveness in the tiles or other details.• For custom made items always provide a drawing with installation indications and the measurements of each single article.

In the case of any uneveness in the walls or fl ooring Antonio Lupi Design S.p.A. declines all responibility for eventual diffi culties during installation of the product, as water leakage or malfunctioning due such diffi culties.

1. Tile coating

2. Stainless profi le

3. Glass (reduced by 2,5 cms. on each side with respect to thetray)

4. Evenly install shower tray

5. Shower tray

SHOWER ENCLOSURE ASSEMBLY DIAGRAM FOR ART 013 - 039 - SLAB

L

P

L - 2,5 cm

L

P

L - 2,5 cm

1

2

3

4

5

(+- 1 cm.) 1

2

3

4

5


F1

F2

1. After having installed the shower tray as per our instructions, mark where the holes should be drilled for installing the wall profi le.

2. Position the profi le on the wall making sure it’s level and making sure that the rubber trimming is on the internal side of the box (F2). Align correctly the profi le within the base of the tray (F1). Fix the profi le to the wall.

INSTALLATION GUIDLEINES FOR SHOWER ENCLOSURE

Trimming


F5

INSTALLATION GUIDLEINES FOR SHOWER ENCLOSURE

3. Insert the glass of the enclosure into the groove of the tray and make sure it’s parallel to it.

4. Verify that it is inserted correctly within the wall profi le and place the trimming that will block it on the external side of the enclosure (F5). Apply a thin layer of silicone between the shower tray and the glass.


F1

1. After having installed the shower tray as per our instructions, mark where the holes should be drilled for installing the wall profi le.

2. Fix the profi le to the wall making sure it is level. P.S. Position the profi le correctly within the base of the tray. (F1)

INSTALLATION GUIDLEINES FOR SHOWER ENCLOSURE ON_OFFregistered model and design, patent pending


F5

INSTALLATION GUIDLEINES FOR SHOWER ENCLOSURE ON_OFF

3. Insert what shall be the fi xed glass into the groove of the tray making sure it is perfectly parallel. Eventual compensations for an uneven wall will have to be managed through the profi le not altering the position of the glass.

4. Verify the correct position of the glass within the profi le and insert the trim in the external side of the enclosure to block it. (F5)

registered model and design, patent pending



5. Assemble the bottom wheel to the sliding door as indicated in the drawing making sure to insert the nylon element (A) in the hole of the glass. To facilitate inserting the anti-release element (B) correctly within the glide, do not completely tighten the wheel.




6. Remove the panels from the tray, dismantle the top wheel to later insert it in the fi xed glass. Position the sliding glass door in the lower glide rotating it as shown to facilitate inserting it in the upper glide.

7. Use the spacer provided to rest the door during installation.



F6

CB

A

OK NOElemento in NylonNylon element.

Elemento in NylonNylon element.


8. After having positioned the sliding door, assemble the top wheel as shown. If it must be adjusted use the nylon element with an off centered hole. (F6)

9. A. Warning: The glass should not rest on the nylon element. B. Adjust the anti-release element verifying that it functions

correctly and tighten the entire mechanism. C. Install the handle as shown



F3

F2


10. Install the support bar using the regulating mechanism (F2) making sure the glass is completely perpendicular to the tray. Fix the nut (F3). For articles ON_OFF78 and ON_OFF88 install the second profi le and the third glass following these instructions. Remove the spacer and place the panels back on the tray.



a

c

b

d

1.2. Ensure to have installed the shower pan correctly following the relative installation instructions, specifi cally make sure that the shower pan is installed in a coplanar manner..

3. Insert the glass in the shower pan preferably following steps a, b, c, d, applying silicone on the sides to be coupled without removing the protective fi lm.

INSTALLATION GUIDLEINES FOR SHOWER ENCLOSURE ISOLA


INSTALLATION GUIDLEINES FOR SHOWER ENCLOSURE ISOLA

4. Position the support bar as indicated in fi g.5 tightening the grub screw as indicated

Allow the silicone used to fi x the glass to dry for at least 12 hours..

5. Only after the silicone has completely dried proceed with cleaning the corners and remove the protective fi lm. Continue with silicone on the bottom borders as indicated


1010

2537

5 5

10

25

20

37

10

5

10

37 25

Shower tray

Masonry

Masonry limit

Plaster limit

Wall covering limit

Wall covering:Corian® / Tiles 10 mm

Masonry

Masonry limit

Wall covering limit

Wall covering 20 mm

Shower tray

Masonry

Wall covering limit

Masonry limitWall covering 30 mm

Shower tray

1. Ensure to have installed the shower pan correctly following the relative instructions, specifi cally observing the requirements for installing the wall covering

3. Wall covering 20 mm

2. Wall covering 10 mm.

ATTENTION: The Corian® wall covering should be applied perfectly perpendicular to the shower tray to avoid working on each singular slab.


INSTALLATION GUIDLEINES FOR SHOWER ENCLOSURE PENISOLA


mm 11 asse foratura

dett. A

mm11 ASSE FORATURA

bordo esternopiatto doccia

5

7 8

6


5. Remove the slats before continuing to install the shower enclosure.

7. The profi le must be fi xed perfectly vertical

6. Fix the profi les provided on the wall ensuring to position it as in Fig.6.8. Repeat this task for the second profi le.


A

B C

9

10


9. Insert glass A ensuring to not damage the element pre-glued A1. Insert the sealing gasket as indicated .

10. Analogously to Fig.4 insert glass B. P.S.: do not remove the adhesive protection near the joint with glass C. Predispose silicone on the side to be coupled between glass B and glass C. Insert glass C by adhering perfectly the bonding surfaces.


a

b

c

11


11. Position the support bar, tightening the grub screw as indicated in detail a. Allow the silicone used to fi x the corner glass to dry for at least 8 hours. Only after the silicone has completely dried in the corners proceed with cleaning the corners and remove the protective fi lm. Continue with silicone on the bottom borders as indicated in detail b.


25

25

L

P

2525

P

Min 123 Max 175

INSTALLATION INSTRUCTIONS SHOWER TRAY

SHOWER TRAY 00

Top mount shower tray Flush mount shower tray

P.S . For each meter of distance from the drain consider 1cm. slope.

SHOWER TRAY 00_Combi

Right Version

Right Version


Versione DX - Right Version

Versione SX - Left Version

L2,6 2,6

2,6

2,6

P

13

Min. 123 - Max 1752,6 13

2

P

542,6

2,6

20,6

18

Min. 67 - Max 119

P.S. From 162 cm. on 2 drain holes will be supplied.Position of the drain hole: length divided by 3ES: 162 : 3 = 54 cm..

P.S. From 162 cm. on 2 drain holes will be supplied.Position of the drain hole: length divided by 3ES: 162 : 3 = 54 cm..

SHOWER ENCLOSURE ASSEMBLY DIAGRAM

013 SHOWER TRAY

013COMBI SHOWER TRAY

The bottom of the shower pan is even; the water drainage is eased through a series of grooves on the surface. It is to be considered normal to fi nd a modest amount of water after its use and thus will not harm the product.We advise airing out the area after its use to disperse the humidity which could cause with time the formation of mold between the shower slabs.

Top mount Flush mount

N.B. For each meter of distance from the outlet consider one centimeter slope.


ok! no!



L

2,7

39

2,7

P

Min. 123 - Max 162

2,739

P

2,7

2,7

2,7

2,7 254

2,7

18 20,6

N.B. From 162 cm. on 2 drain holes will be supplied.Position of the drain hole: length divided by 3ES: 162 : 3 = 54 cm..

N.B. From 162 cm. on 2 drain holes will be supplied.Position of the drain hole: length divided by 3ES: 162 : 3 = 54 cm..





039 COMBI SHOWER TRAY

039 SHOWER TRAY


Min. 121,5 - Max. 173,5

3,7

Min. 121,5 - Max. 173,5

53,81

19,5

78,5

/ 88

,5

1 1

1

1

38,5 12,5



3,7

78,5

/ 88

,5

1 1

1

1

38,5 12,5Min. 121,5 - Max. 290,5

Min. 121,5 - Max. 290,5N.B. From 160,5 cm on 2 drain holes will be supplied.Position of the drain hole: length divided by 3ES: 160,5 : 3 = 53,5 cm

N.B. From 160,5 cm on 2 drain holes will be supplied.Position of the drain hole: length divided by 3ES: 160,5 : 3 = 53,5 cm





0XCOMBI SHOWER TRAY

0X SHOWER TRAYregistered model and design



1/2

20

20

1/2

40 /

4535

/ 40

/ 45

20

80 /

9070

/ 80

/ 90

80 /

905

33

INSTALLATION INSTRUCTIONS SHOWER TRAY

SHOWER TRAY ZEROMAT_ST

Top mount shower tray Flush mount shower tray

P.S . For each meter of distance from the drain consider 1cm. slope.

SHOWER TRAY ZEROMAT_ML

SHOWER TRAY ZEROMAT_ML


L

10 ? 10

10?

10

P


SLAB SHOWER TRAY





4,8 cm

90°

90°

L3

L4

L3 = L1 - 4 cmL4 = L2 - 4 cm

60 mm1248

7,5 cm

IMPORTANTThe bottom of the tray must rest on a uniform and level fl oor. Do not

leave empty spaces or bumps.

Fill after having positioned the trap

WARNING:The installation must be done according to National code and regulations regarding civil plumbing waterworks. Thus installation must be done by specialized professionals only who should certify the work done. Antonio Lupi Design declines all responsibility of any malfunctioning if such documentation is not presented. The material used is of great quality however can still be damaged if in contact with aggressive chemical agents such as acetone or solvents in general. In such a case remove immediately. During installation protect the surface to avoid damaging it.

1. Prepare the fl ooring.

3. When the concrete is completely dry lay the basin of the shower with care and silicone it or glue it with tile adhesive. Make sure the basin is perfectly level. Compress the plate carefully to the concrete so as not to damage it until the glue or silicone is completely dry.

2. The bottom should be completely smooth and even in all directions. Install the drain following the instructions provided.

4. Fix the plug of the drain.

IMPORTANT:In case your shower enclosure doesn’t forsee a border we suggest also installing, apart from the rubber on the bottom of the glass, a profi le to hold back the water (usually provided with the shower enclosure). In case the shower is not closed on all sides, carefully calculate an adequate distance from the drain to avoid water splashing out. If this should happen Antonio Lupi Design declines all responsibility if not due to a malfunctioning of the tray itself.

wall covering

seal

backingborder of hole

rim of tray

INSTALLATION INSTRUCTIONS SHOWER TRAY 00_ST/00_XL/00_COMBI TOP MOUNT VERSION


90°

90°

L3

L4

L3 = L1 - 4 cmL4 = L2 - 4 cm

60 mm1248

7,5 cm

INSTALLATION INSTRUCTIONS SHOWER TRAY 00_ST/00_XL/00_COMBI FLUSH MOUNT VERSION

IMPORTANTThe bottom of the tray must rest on a uniform and level fl oor. Do not

leave empty spaces or bumps.

Fill after having positioned the trap

WARNING:The installation must be done according to National code and regulations regarding civil plumbing waterworks. Thus installation must be done by specialized professionals only who should certify the work done. Antonio Lupi Design declines all responsibility of any malfunctioning if such documentation is not presented. The material used is of great quality however can still be damaged if in contact with aggressive chemical agents such as acetone or solvents in general. In such a case remove immediately. During installation protect the surface to avoid damaging it.

1. Prepare the fl ooring.


2. The bottom should be completely smooth and even in all directions. Install the drain following the instructions provided.

4. Fix the plug of the drain.

IMPORTANT:In case your shower enclosure doesn’t for see a border we suggest also installing, apart from the rubber on the bottom of the glass, a profi le to hold back the water (usually provided with the shower enclosure). In case the shower is not closed on all sides, carefully calculate an adequate distance from the drain to avoid water splashing out. If this should happen Antonio Lupi Design declines all responsibility if not due to a malfunctioning of the tray itself.

wall covering

backingborder of hole

rim of tray

seal


2,7 cm

4 cm

x85 mm

L1 L2

S1 S2= = =

90°90°90°90°

INSTALLATION INSTRUCTIONS 013/013COMBI - 039/039COMBI TOP MOUNT VERSION

IMPORTANT INFORMATION: The installation should be done respecting the national laws and plumbing codes of your country.The installation of the shower tray should be done by an authorized plumber who should leave a declaration of plumbing conformity relative to the installation. Antonio Lupi Design declines all liability in lack of thus documentation.The material employed for the construction of the product is of excellent quality even though can be damaged if in contact with aggressive chemical agents such as acetone or solvents in general. In case this should happen remove immediately the stains.During installation we recommend to cover the product so as to avoid superfi cial abrasions.

1. Prepare the foundation, which must be even and levelled on each side.


P.S.Encase into the wall approx. 1/1,5 cm. the borders of the tray adjacent to it and seal the edges with silicone. Assure that the bottom of the tray is completely levelled on each side. Fix the drain plug.

2. Install the included drain pipe fi tting following the relative instructions and keeping it aligned between the superior border of the drain and the bottom surface of the tray (Fig. 2).

4. Carefully lay slabs

Guidelines for selecting a shower enclosure:• Make sure that none of the structural parts of the enclosure

are installed upon the slats. • The shower tray with TEAK slats is not suitable for shower

enclosures which open towards the inside.

IMPORTANT: In the case you have a shower cabin without a resting profi le, for correct use of the shower tray, it is advisable to foresee, in addition to the bottom fi tting, a containment profi le usually included with the shower cabin. In the case of open sides (without shower cabin) calculate the necessary distance from the water outlet to reduce the possibility of spouting water, in this case, however, Antonio Lupi Design declines all liability for water spilling out which is not attributable to the shower tray itself. (Fig. 4 Part. A)

IMPORTANT

IMPORTANT

Shower doorContainment profi le

Resting Profi le

Untilled landPART. AUntilled land

Wal

l

Fill after having positioned the drain.

IMPORTANTThe bottom of the shower tray must lay on a uniform and levelled surface.Do NOT leave any empty spaces or bumps.


3 mm

90°90°

90°90°

3 mm

INSTALLATION INSTRUCTIONS FOR 013/013COMBI - 039/039COMBI FLUSH VERSION

WARNING: The installation should be done respecting the national laws and plumbing codes of your country. The installation of the shower tray should be done by an authorized plumber who should leave a declaration of plumbing conformity relative to the installation.Antonio Lupi Design declines all liability in lack of thus documentation. The material employed for the construction of the product is of excellent quality even though can be damaged if in contact with aggressive chemical agents such as acetone or solvents in general. In case this should happen remove immediately the stains. During installation we recommend to cover the product so as to avoid superfi cial abrasions.

1. Dig the trench in the fl oor according to the dimensions of the shower tray keeping in mind that the total height of the tray is approx. 4 cm. The ground must be completely fl at and level on all sides.


P.S.Encase into the wall approx. 1/1,5 cm. the borders of the tray adjacent to it and seal the edges with silicone. Assure that the bottom of the tray is completely levelled on each side. Fix the drain plug.

2. Install the included drain pipe fi tting following the relative instructions and keeping it aligned between the superior border of the drain and the bottom surface of the tray (Fig.2)


Guidelines for selecting a shower enclosure:• Make sure that none of the structural parts of the enclosure

are installed upon the slats. • The shower tray with TEAK slats is not suitable for shower

enclosures which open towards the inside.

IMPORTANT: In the case you have a shower cabin without a resting profi le, for correct use of the shower tray, it is advisable to foresee, in addition to the bottom fi tting, a containment profi le usually included with the shower cabin. In the case of open sides (without shower cabin) calculate the necessary distance from the water outlet to reduce the possibility of spouting water, in this case, however, Antonio Lupi Design declines all liability for water spilling out which is not attributable to the shower tray itself. (Fig. 4 Part. A)

x85 mm

L1 L2

S1 S2if L1 > 162 cms. for see 2 drains

= = =

Tile coating

Untilled land

Wal

l

OK

IMPORTANT

IMPORTANT

Shower doorcontainment profi le

Resting Profi le

Untilled land PART. A




10

5

10

37 25

5

10

25

20

37

10

5

10

2537

Shower tray

Masonry

Masonry limit

Plaster limit

Wall covering limit

Wall covering:Corian® / Tiles 10 mm

Masonry

Masonry limit

Wall covering limit

Wall covering 20 mm

Shower tray

Masonry

Wall covering limit

Masonry limitWall covering 30 mm

Shower tray

1. Wall covering 10 mm.

ATTENTION: The Corian® wall covering should be applied perfectly perpendicular to the shower tray to avoid working on each singular slab.



WALL COVERING SPEC SHEET FOR art. 0X - 0XCOMBIregistered model and design


85 mm

90°90°90°90°

x

L1L2

OKS1 S2= = =


INSTALLATION INSTRUCTIONS 0X/0XCOMBI TOP MOUNT VERSION

IMPORTANT INFORMATION:The installation should be done respecting the national laws and plumbing codes of your country.The installation of the shower tray should be done by an authorized plumber who should leave a declaration of plumbing conformity relative to the installation. Antonio Lupi Design declines all liability in lack of thus documentation.The material employed for the construction of the product is of excellent quality even though can be damaged if in contact with aggressive chemical agents such as acetone or solvents in general. In case this should happen remove immediately the stains.During installation we recommend to cover the product so as to avoid superfi cial abrasions.





IMPORTANT:In the case you have a shower cabin without a resting profi le, for correct use of the shower tray, it is advisable to foresee, in addition to the bottom fi tting, a containment profi le usually included with the shower cabin. In the case of open sides (without shower cabin) calculate the necessary distance from the water outlet to reduce the possibility of spouting water, in this case, however, Antonio Lupi Design declines all liability for water spilling out which is not attributable to the shower tray itself.

IMPORTANT

IMPORTANT


if L1 > 160,5 cms. for see 2 drains



S1 S2= = =

3 mm

90° 90°

90° 90°

3 mm

INSTALLATION INSTRUCTIONS FOR 013/013COMBI - 039/039COMBI FLUSH VERSION

IMPORTANT INFORMATION:The installation should be done respecting the national laws and plumbing codes of your country. The installation of the shower tray should be done by an authorized plumber who should leave a declaration of plumbing conformity relative to the installation.Antonio Lupi Design declines all liability in lack of thus documentation. The material employed for the construction of the product is of excellent quality even though can be damaged if in contact with aggressive chemical agents such as acetone or solvents in general. In case this should happen remove immediately the stains. During installation we recommend to cover the product so as to avoid superfi cial abrasions.

1. Dig the trench in the fl oor according to the dimensions of the shower tray keeping in mind that the total height of the tray is approx. 3,7 cm. The ground must be completely fl at and level on all sides.


2. Install the included drain pipe fi tting following the relative instructions and keeping it aligned between the superior border of the drain and the bottom surface of the tray (Fig.2)



x85 mm

L1 L2

if L1 > 160,5 cms. for see 2 drains

OK

IMPORTANT

IMPORTANT




85 mm

90°90°

90°90°

INSTALLATION INSTRUCTIONS FOR SHOWER TRAYS SLAB TOP MOUNT VERSION


1. Prepare the foundation , which must be even and levelled on each side.


P.S. Encase into the wall approx. 1/1,5 cm. the borders of the tray adjacent to it and seal the edges with silicone. Assure that the bottom of the tray is completely levelled on each side. Fix the drain plug.


4. Carefully lay the center footboard, eventually by using the suction cup included.

P.S.The footboard has a slight inclination, it is best to position it so the water fl ows towards a wall instead of towards the shower cabin. (Fig. 4 PART. B)

IMPORTANT:In the case you have a shower cabin without a resting profi le, for correct use of the shower tray, it is advisable to foresee, in addition to the bottom fi tting, a containment profi le usually included with the shower cabin. In the case of open sides (without shower cabin) calculate the necessary distance from the water outlet to reduce the possibility of spouting water, in this case, however, Antonio Lupi Design declines all liability for water spilling out which is not attributable to the shower tray itself. (Fig. 4 Part. A)

x85 mm

L1 L2 OK

IMPORTANT

IMPORTANT


Resting Profi le

wal

l

PART. B

Untilled landPART. A



Tile coating

Untilled land

Wal

l


x85 mm

L1 L2

3 mm

90°90°

90°90°

3 mm

INSTALLATION INSTRUCTIONS FOR SHOWER TRAYS SLAB FLUSH VERSION

OK

IMPORTANT

IMPORTANT


Resting Profi le

massetto PART. A

PART. Bpare

te


1. Dig the trench in the fl oor according to the dimensions of the shower tray keeping in mind that the total height of the tray is 5 cm. The ground must be completely fl at and level on all sides.



2. Install the included drain pipe fi tting following the relative instructions and keeping it aligned between the superior border of the drain and the bottom surface of the tray

(Fig. 2).

4. Carefully lay the center footboard, eventually by using the suction cup included.

P.S. The footboard has a slight inclination, it is best to position it so the water fl ows towards a wall instead of towards the shower cabin. (Fig. 4 PART. B)

IMPORTANTE:In the case you have a shower cabin without a resting profi le, for correct use of the shower tray, it is advisable to foresee, in addition to the bottom fi tting, a containment profi le usually included with the shower cabin. In the case of open sides (without shower cabin) calculate the necessary distance from the water outlet to reduce the possibility of spouting water, in this case, however, Antonio Lupi Design declines all liability for water spilling out which is not attributable to the shower tray itself. (Fig. 4 Part. A)



Tile coating

Untilled land

Wal

l


OK NO

90°90°

7,5 cm

40/45 cm

40/45

20 cm

90°90°


INSTALLATION INSTRUCTIONS ZEROLUX TOP MOUNT VERSION

IMPORTANT INFORMATION:The installation should be done respecting the national laws and plumbing codes of your country.The installation of the shower tray should be done by an authorized plumber who should leave a declaration of plumbing conformity relative to the installation. Antonio Lupi Design declines all liability in lack of thus documentation.The material employed for the construction of the product is of excellent quality even though can be damaged if in contact with aggressive chemical agents such as acetone or solvents in general. In case this should happen remove immediately the stains.During installation we recommend to cover the product so as to avoid superfi cial abrasions.





IMPORTANT

IMPORTANT



90°90°

90°90°

7,5 cm

40/45 cm

40/45

20 cm

3 mm

INSTALLATION INSTRUCTIONS FOR SHOWER TRAYS ZEROLUX FLUSH VERSION

OK

IMPORTANT

IMPORTANT


1. Dig the trench in the fl oor according to the dimensions of the shower tray keeping in mind that the total height of the tray is 5 cm. The ground must be completely fl at and level on all sides.




(Fig. 2).

IMPORTANTE:In the case you have a shower cabin without a resting profi le, for correct use of the shower tray, it is advisable to foresee, in addition to the bottom fi tting, a containment profi le usually included with the shower cabin. In the case of open sides (without shower cabin) calculate the necessary distance from the water outlet to reduce the possibility of spouting water, in this case, however, Antonio Lupi Design declines all liability for water spilling out which is not attributable to the shower tray itself.




90°90°

20 cm

90°90°

7,5 cm

INSTALLATION INSTRUCTIONS FOR SHOWER TRAY ZEROMATT_ML FLUSH MOUNT VERSION

WARNING:The installation must be done according to National code and regulations regarding civil plumbing waterworks. Thus installation mustbe done by specialized professionals only who should certify the work done. Antonio Lupi Design declines all responsibility of anymalfunctioning if such documentation is not presented. The material used is of great quality however can still be damaged if in contactwith aggressive chemical agents such as acetone or solvents in general. In such a case remove immediately. During installation protectthe surface to avoid damaging it.

1. Prepare the fl ooring, making sure its level in each direction.

3. When the concrete is completely dry lay the basin of the shower with care and silicone it or glue it with tile adhesive in

modest quantities. Make sure the basin is perfectly level. Fix the drain.

2. Install the included drain pipe fi tting following the relative instructions and keeping it aligned between the superior

border of the drain and the bottom surface of the tray.



OK

IMPORTANT

IMPORTANT


NOcenter

center


90°90°

20 cm

90°90°

7,5 cm

INSTALLATION INSTRUCTIONS FOR SHOWER TRAY ZEROMATT_ML ENCASED VERSION

WARNING:The installation must be done according to National code and regulations regarding civil plumbing waterworks. Thus installation mustbe done by specialized professionals only who should certify the work done. Antonio Lupi Design declines all responsibility of anymalfunctioning if such documentation is not presented. The material used is of great quality however can still be damaged if in contactwith aggressive chemical agents such as acetone or solvents in general. In such a case remove immediately. During installation protectthe surface to avoid damaging it.

1. Dig the trench in the fl oor according to the dimensions of the shower tray keeping in mind that the total height of the tray is approx. 5 cm. The ground must be completely fl at and level on all sides.

3. When the concrete is completely dry lay the basin of the shower with care and silicone it or glue it with tile adhesive in

modest quantities.



(drawing n.2).





OK

IMPORTANT

IMPORTANTNO

center

center


b

a

c

d

INSTALLATION ART. AGUA

a. adjusting screwb. bolts for fi xingc. chemical fi xingsd. fi ttings ½G


Art. SBALZO INSTALLATION


Art. PRISMA INSTALLATION


45 cmA

B

C

1. Fix the stainless steel supports to the wall at 45cm in height using the screws provided. The installer should make sure that the screws provided are suitable for the type of wall. We will not be held responsible for eventual damages if installed incorrectly.

3. Tighten the screws between the stool and the supports.

2. Insert the stool on the supports and block it in the up right position.

4. To recline the stool, slightly push upwards (A) then outwards (B) and rotate downwards (C).

CLEANINGClean with a soft damp cloth and neutral soap. Do not use abrasive sponges or abrasive cleaners containing alcohol or acids.

Art. TAO INSTALLATION


Ø 40 mm Ø 40 mm

OK5 cm

1. Prepare the holes for the fi xings in the wall depending on the type of sink selected. The sinks are supplied with integrated supports in stainless steel (Fig. 1). Carefully align the holes so the supports are perfectly leveled.

P.S.The position of the drain is off center 7 cm. (see image).

3. Apply a lubricant to the rubber connecting pipe attached to the drain pipe. Fix an extension muff to the drain pipe of the sink and cut to the length needed for insertion into the wall.

2. Fix the sink to the wall with the appropriate screws provided and to the connecting drain pipe. It is advisable to not exag-gerate when tightening the screws so as not to damage the sink.

IMPORTANT: Because of the particular conformation of the incorporated drainage system the sink must be installed completely leveled in each direction.

4. After having installed the sink verify its correct operation and that the cap is fastened tightly A.

Single sink with incorporated trapThe sink must be connected to the drain calculating the necessary ventilation (see Plumbing Scheme). In the case that this is not possible we advise using Art.MYSLOT.

Double sink with incorporated trapThe sinks must be connected individually to the central drain as if they were independent, calculating the ventilation for each singular element (see Plumbing Scheme). In the case that this is not possible we advise using Art. MYSLOT

INSTALLATION DIAGRAM SLOT 21/22/23/AD/BD/XL SINKS WITH HIDDEN DRAIN

level

Fig. 1drain Ø 40 mm


PLUMBING SCHEME ART. SLOT AD - SLOT BD

Top with double integrated sink and integrated siphon

The sinks must be connected individually to the central drain as if they were independent, calculating the ventilation for each singular element (see Plumbing Scheme). In the case that this is not possible we advise using Art. MYSLOT.

1. Wrong installation

2. Correct installation

3. Suggested installation

Ventilation piping

Drain piping


PLUMBING SCHEME FOR ART. SLOT 21/22/23/XL

Ventilation piping

Condotte scarico

Single sink with incorporated trap

The sink must be connected to the drain calculating the necessary ventilation. In the case it is not possible to give the necessary ventila-tion, in the case this is not possible we advise using Art. MYSLOT

1. Wrong installation

2. Correct installation

3. Suggested installation


EXAMPLE OF HOW TO FIX A SINK TO THE FLOOR

1. Please note the position of the holes on the bottom of the sink and mark the surface where mounting. Drill accordingly and insert into the surface where mounting, the bolts provided, after which simply match up the holes with the bolts in the surface and rest the basin on these.


1130

600

410

896

630

600

410

89637,8

77,7

INSTALLATION GUIDLINES FOR ART.H12

2-3. install the support considering the characteristics of the wall covering to be used as well as the position of the sink. (Fig. 2 and 3)

4. Apply silicone to the support. Install the basin by resting it on the support.

Support for art.H12144 e H121144

Support for art.H1290 e H12190


INSTALLATION GUIDLINES FOR ART.STRAPPO


ELECTRIC DIAGRAM ART. STRAPPO


ELECTRIC DIAGRAM OIO3L


ELECTRIC DIAGRAM OIO4L


Remote controller

BASIC PARAMETERFrequency 433.92 MHzSupport DC 12/24V input,max power 216W. Electrical device not protected from water or humidity (this is a non waterproof device)Operating Instructions (remote control is touching button)Touch ON/OFF (1-2) button, you can switch on/off the RGB strip.Slide the color ring (5), RGB strip will show the same color.Increasing color button (3) can adjust the current color to the most vivid, decreasing color button (4) is contrary, until pure white.You can adjust the brightness by dimming function (6-7), to brighten and dim the light.Gradual change mode: Touch on button again under monochrome mode condition, RGB strip will be changed into gradual change mode. Increasing color button will speed up the color change, decreasing color button will slowdown. Hopping mode: under gradual change mode condition, touch on button, the RGB strip will be changed into hopping mode. Increasing color button will speed up the hopping, decreasing color button will slowdown (3-4). Under Gradual change or hopping mode, touching on switch will change one to the other. Close the RGB strip and restart it if you want to enter monochrome mode.AttentionsMatch the color of output wiring when connecting .When the color doesn’t match, for example, it displays blue when touching green,or displays green when touching blue, please check whether the wiring is correct. In this case, exchange blue and green.

PRESENTATION MODE1. Gradual Change Mode

Under powered condition, press No.2 button, RGB controller will be changed into gradual change mode. Touch 3/4 button, (show as bellow) you can control the speed of gradual change, 3 to speed, 4 to slowdown. Changing them into normal mode need close the RGB controller and restart it.

2. Hopping modeUnder gradual change mode condition, touch No.2 button, the RGB controller will be changed to hopping mode. Touch 3/4 button can control the speed of it, 3 to speed, 4 to slowdown. Changing them to normal mode need restart the RGB controller.

Pay attention: The change of the above two presentation mode need 4 seconds.

1. OFF

2. ON

3. color saturation +

4. color saturation -

5. color ring

6.dimmer +

8. indicator

7.dimmer -

keep away from water


ELECTRIC DIAGRAM OIO3B


ELECTRIC DIAGRAM OIO4B


s

b

AC

H

1. To fix the wall cabinet at the height desired A, insert B with S found on the back of the cabinet and measure distance H from the top border of the mirror to the center of the holes on the support S.

3. Place the cabinet as in the diagram above.

2. Fix S to the wall making sure the center of the holes is at height C (C= A-H). In the case you should have more than one bar due to the length of the cabinet fix it to the wall level with the first.

INSTALLATION GUIDLEINES FOR ART. TEATRO


A C

H

1. To fix the wall cabinet at the desired height A insert the bracket s in the attachment b found on the back of the cabinet. Measure distance H between the top of the cabinet and the center of the holes of the bracket.

3. Hook the cabinet to the bracket as shown.

2. Fix the bracket s on the wall where the holes are at height C (C=A-H), place the eventual second bracket level with the first and fix on the wall.

4. Cabinet hung on the wall

ASSEMBY DIAGRAM FOR WALL HANGING CABINETS


INSTALLATION GUIDLEINES FOR ART. SEGRETO


INSTALLATION GUIDLEINES FOR ART. SEGRETO


INSTALLATION GUIDLEINES FOR ART. FRATAK


ASSEMBLY DIAGRAM FOR SINK DISPLAY

1. Follow the assembly instructions of the display cabinet as per fi g.1 for the single model or as in fi g.2 for the double model making sure to tighten all the screws.

CAUTION: Do not use ethyl alcohol or solvents of any kind to clean the logo.


ASSEMBLY DIAGRAM FOR art. ONDA

1 WC plate2 Tank fi xing mask3 Adjustable mounting bracket4 Magnetic blocks - permanent neodymium magnet kg 24 x 25 Fixing nuts for tank mask**6 Button adaptor nuts 7 Button adaptor gafts8 Distance elements for mask*

*Only for tank mod. UNICA+ art 111.329.00.5 56 (export)**Only for tank mod. UNICA+ for the model UNICA art 109.760.001 use the screws provided

The fl ush plate art. Onda is compatible with encased toilet cisterns of the company Geberit in the Unica model as well as art. 109.760.00.1 - art. 109.770.00.1 – art. 111.329.00.5.56


1 2

3 4

max 5 mm

max 5 mm


permanent neodymium magnet kg 24 x 2

element not included

from 1.5 to 4 cm of plaster / fi nish


5 6

7 8


hook position – 1mm

allign upper support bracket (3) to lower magnetic fastening elements (4) at 1mm maintain graft panel (7) at 3mm border wall covering

0,0 wall covering limit


INSTALLATION ART. ONDA FOR EXPOSURE


CLEANING/INSPECTION SIPHON

Art. MICRO Art. PLUS

1. Remove the bottom of the siphon, using the allen wrench

2. Proceed with inspection

3. Replace cover

1. Remove bottom part of the siphon

2. Proceed with inspection

3. Replace bottom part of siphon


A

CLEANING/INSPECTION SIPHON ART. SINTESI

To clean the inside of the siphon (A), unscrew the siphon base simply using a coin. Clean inside with water only. Do not use corrosive substances.


Exelen Collection

MATERIALS USED USAGE AND MAINTENANCE INSTRUCTIONS

Warning:The current product information complies with law n.126 of the 10th of April 1991 “Regulations for consumer information” and to ordinance n.101 of the 8th of February 1997 “Fulfi lment Regulations”

PRODUCT DESCRIPTION

LACQUERED VERSION – WOOD VERSION

StructureGrey laminated medium density fi berboard 18 mm thick.

WOOD VERSION

FrontsPoplar plywood with phenolic adhesive veneered with 6 tenths oak.

End panelsMedium density fi berboard 12 mm thick veneered with 6 tenths oak.

Open cabinetsFinnish birch plywood with a phenolic adhesive veneered with 6 tenths oak.

LacqueringVarious colours open pore painted with acrylic paints.

LACQUERED VERSION

TopMedium density fi berboard lacquered with polyurethane paint.

Fronts, open cabinets and end panelsMedium density fi berboard lacquered with polyurethane paint.

WOOD VERSION – LACQUERED VERSION

Internal selve8 mm fl oat glass

DrawersGuides and painted steel sides with an automatic stopping device with bottom panel of particle board laminated grey.

SupportsGalvanized steel

HingesNickel plated steel

CLEANING

Wood version

Clean the furniture with a non abrasive soft damp cloth only. Do not use cleaning products which may damage the matt fi nish. Use exclusively the product CLEANWOOD, purchasable through our company.Apply with a soft cloth and distribute evenly over the surface to be treated.

Lacquered version

Clean the furniture with a soft damp cloth or non abrasive sponge or with diluted acetyl alcohol. All cleaning should be done with great care so as not to scratch the surface. Avoid the usage of products containing ammonia, acetone, chlorine, solvents as well as abrasive products.

The laquering of glass tops and mirrors are done by hand Speks or slight difference with the sample-board colours may not give rise to any disputes. To avoid damaging the fi nish, installation is required utilizing the non acidic silicone supplied.

ATTENTIONAvoid the use of detergents containing ammonia and or solvents and alcohol. Coffe or tea stain the product permanently.

SECURITY

Do not make any modifi cations to the furniture which could cause the structure to become unstable.

TOXICITY

The product does not result to be toxic to humans, animals or to the environment.The panels in fi bre wood, particle boards and plywood used conform to regulation EN120 CLASSE E1, with limited emission of formaldehyde.

ECOLOGY

Only discard in appropriate disposals according to rules and regulations in your area.


WOOD VERSION

Structure, fronts and open shelved cabinetsFinnish birch phenolic adhesive plywood and 6 tenths wood veneered.

Back panelPoplar ply oak veneered. LacqueringOpen pore painting in various colours with an acrylic fi nish.

LACQUERED VERSION

Structure, fronts and open shelved cabinetsMedium density fi bre board lacquered with polyurethane paints.

Rubber fi nish Lacquered with paints with a polyurethane base.

WOOD VERSION - LACQUERED VERSION

Internal shelves8 mm fl oat glass.

DrawersRunners and sides in painted steel with automatic recall and internal shock absorber with the bottom panel in a melamine laminated grey fi nish particle board.

Shelf holdersNickel plated metal


PlinthMedium density fi bre board lacquered with acrylic and polyester paints.

“LUNARIA” collection


CLEANING

Wood version


Lacquered version



Cleaning rubber fi nish

For dry dirt (i.e. dust) use only a damp cloth with water.For greasy dirt (i.e. fi nger prints) use fi rst a wet sponge with water and liquid detergent, after which eliminate the detergent with a damp cloth with water.


SECURITY


TOXICITY


ECOLOGY



PRODUCT DESCRIPTION



Piana Collection



PRODUCT DESCRIPTION

LACQUERED VERSION – WOOD VERSION

StructureGrey laminated medium density fi berboard 18 mm thick.

WOOD VERSION

FrontsPoplar plywood with phenolic adhesive veneered with 6 tenths oak.

End panelsMedium density fi berboard 12 mm thick veneered with 6 tenths oak.

Open cabinetsFinnish birch plywood with a phenolic adhesive veneered with 6 tenths oak.

LacqueringVarious colours open pore painted with acrylic paints.

LACQUERED VERSION

TopMedium density fi berboard lacquered with polyurethane paint.

Fronts, open cabinets and end panelsMedium density fi berboard lacquered with polyurethane paint.

WOOD VERSION – LACQUERED VERSION

Internal selve8 mm fl oat glass

DrawersGuides and painted steel sides with an automatic stopping device with bottom panel of particle board laminated grey.

SupportsGalvanized steel


CLEANING

Wood version


Lacquered version




SECURITY


TOXICITY


ECOLOGY



WOOD VERSION

TopsFinnish birch phenolic adhesive plywood and 6 tenths wood veneered. Structure, fronts and open shelved cabinetsFinnish birch phenolic adhesive plywood and 6 tenths wood veneered.


LACQUERED VERSION

TopsMedium density fi bre board lacquered with polyester paints.









“Panta rei” collection


CLEANING

Wood version


Lacquered version






SECURITY


TOXICITY


ECOLOGY



PRODUCT DESCRIPTION



WOOD VERSION

TopsFinnish birch phenolic adhesive plywood and 6 tenths wood veneered. Structure, fronts and open shelved cabinetsFinnish birch phenolic adhesive plywood and 6 tenths wood veneered.


LACQUERED VERSION










“Planeta” collection


CLEANING

Wood version


Lacquered version






SECURITY


TOXICITY


ECOLOGY



PRODUCT DESCRIPTION


WOOD VERSION

TopsFinnish birch phenolic adhesive plywood and 6 tenths wood veneered. Structure, fronts and open shelved cabinetsPoplar phenolic adhesive plywood 6 tenths wood veneered.

Back panelPoplar ply oak veneered in wood essence. LacqueringOpen pore painting in various colours with an acrylic fi nish.

LACQUERED VERSION


StructureMedium density fi bre board 18 mm. thick laminated and bordered grey fi nish, lacquered externally with polyurethane paints.

Fronts and open shelved cabinetsMedium density fi bre board lacquered with polyurethane paints.

Back panelWood fi bre panel laminated grey fi nish.

Shaped frontsHard expansion polyurethane or medium density fi bre board lacquered with polyurethane paints.







StemsPACO – Stainless steelRITTO – Chrome plated brass

HandlesRAIL – Oak HardwoodFREE – Stainless steelSIGN – Chrome plated metalRIGO – Chrome plated brass

“Materia” collection


CLEANING

Wood version


Lacquered version






SECURITY


TOXICITY


ECOLOGY



PRODUCT DESCRIPTION


VERSIONE LEGNO

Vetro fl oat 19 o 15 mm verniciato con vernici acriliche.

PannelloPannello di fi bra di legno a media densità laccato con vernici poliuretaniche.

StrutturaAcciaio inox

PortasalvietteAcciaio inox

MascherinaAlluminio anodizzato

“Aero” collection


CLEANING

Clean the glass tops with diluted acetyl alcohol or commonly used cleaners. Clean the stainless steel parts with diluted acetyl alcohol.Avoid the usage of solvents, abrasive and acidic products.For installation do not use acidic silicone which could stain the surface. Strictly use non acidic silicone.The top is made of glass, a fragile material, and so must be handled with care.

TOXICITY

The product does not result to be toxic to humans, animals or to the environment. The panels in fi bre wood conform to regulation EN120 CLASSE E1, with limited emission of formaldehyde.

ECOLOGY



PRODUCT DESCRIPTION


Top 16 mmExtra clear fl oat glass 15 mm thick painted with acrylic paints.The 16 mm thickness is obtained with the paint.

Top 20 mmFloat glass 19 mm thick painted with acrylic paints. The 20 mm thickness is obtained with the paint.

16 mm acid glass topultra clear 15 mm acid fl oat glass lacquered with acrylic paints.

LAQUERING


Glass tops


CLEANING

Clean with diluted acetyl alcohol or commonly used glass cleaners.Avoid the usage of solvents, abrasive and acidic products.For installation do not use acidic silicone as it may stain the surface. Use only the silicone provided.

As noted glass is a fragile material, and so must be handled with care.

Advise for cleaning glass tops with an acid fi nish

To remove eventual stains which may be caused during the cleaning of such, follow the following procedures:Evenly scatter the dry cleaning product provided with the glass top over the stain to be removed and by using the palm of your hand rub hard.Wash out thoroughly with hot water and with a cotton cloth remove he excess product.Repeat a second time if after this procedure the stain remains

ATOXICITY

The product does not appear toxic to humans, animals or to the environment.

ECOLOGY

Only discard in appropriate disposals according to rules and

PRODUCT DESCRIPTION



Polyethylene sinks/bathtubs


PRODUCT DESCRIPTION

Toilet seat cover in thermosetting resin

MATERIALS USED INSTRUCTIONS FOR USE AND MAINTENANCE

POLYETHYLENESpecifi c low-density polyethylene for rotational molding

CLEANINGClean with a damp cloth or with common liquid detergents for domestic use.

Do not use aggressive chemical products such as acetone, trichlorethylene nor strong acids.

TOXICITYThe product does not appear toxic to humans, animals or to the environment.

ECOLOGYOnly discard in appropriate disposals according to rules and regulations in your area.


Main raw materials used:Urea

Secondary materials used:Hinges in stainless steel 18/10Buffers in polypropyleneFixing screws in stainless steel 18/10

Resistance to breakage:The maximum weight the cover can bear is equal to 250 kg (551 Lb). Above this amount the cover can break at any point or way depending on the weight distribution.

Fire resistance:The urea used for the production of the toilet seat cover in thermosetting resin is equal to 490°C (914 °F).

CLEANINGClean with a soft sponge or cloth.Make use of detergents commonly used for the home and avoid the use of steel wool and or products that contain acid, chlorine, ammonia, and are corrosive or abrasive.

CAUTION: if using specifi c products or which has a prolonged effect to clean ceramic avoid contact with the seat cover and hinges. If this should happen immediately rinse out thoroughly. Do not lower the seat or cover to avoid exposure to fumes which could alter the colour.

TOXICITYThe product does not appear to be toxic to humans, animals or environment.

ECOLOGYOnly discard in appropriate disposals as according to rules and regulations in your area.


Ceramic sanitary-ware / sinks


PRODUCT DESCRIPTION

Cristalplant® sinks, tops and tubs

MATERIALI IMPIEGATI ISTRUZIONI PER L’ USO E MANUTENZIONE

VITREOUS CHINA

OVOORBISTOYL910ABOLCUPOLAEVAKUOKOMODOMASCOLOSELLA

FIRE CLAY ECO2 ECO3 CARTER EVAKUOECO LAICOALBUMALBUM3FIUMEFIUME3FIUME4RELIGIORELIGIO3PIVOT1

CLEANING

Clean with warm water and non abrasive detergents.In case of heavy calcareous deposits use diluted hydrochloric acid.

Avoid striking with hard or sharp objects so as not to create chipping.

TOXICITY


ECOLOGY


CRISTALPLANT®

Cristalplant® is a patented composite material comprising mainly of natural minerals of aluminum hydrate bonded with a small percentage of resins.

CLEANING

Clean with a damp cloth or with common liquid detergents for domestic use. Particularly recommended are liquid detergents such as CIF® used with an abrasive sponge such as a SCOTCH BRITE® pad.

Do not use aggressive chemical products such as acetone, trichloroethylene nor strong acids.

Removing stubborn stains, scratches and burnsCristalplant® is a material homogeneous throughout its thickness and scratches, cigarette burns and stubborn stains can be removed returning the surface to its original beauty by following these instruction: For light superfi cial damage, the surface can be restored by using an abrasive Scotch-Brite® pad (trade mark of 3M) and household abrasive cleaner. For more deeper damage one can sand the damaged area. If the defect is still visible, repeat the sanding using very fi ne grain abrasive paper.

TOXICITY


ECOLOGY





PRODUCT DESCRIPTION


CERAMILUX®

Ceramilux® is a material composed of natural mineral charges (calcium carbonates and aluminium trihydrates) and polyester resin. The gelcoat fi lm that covers the surface of the material is of the iso/neopentilic polyester type which allow excellent characteristics of resistance to be obtained. Its appearance and its mechanical land chemical characteristics make this material perfectly suitable for furnishing bathrooms and public rooms.

ALABULBOCANYONCORNERDUNEFOGLIOGESTOGIROGIROSERVOTRIOTONDOTRIOVALEPIPER

WANDA

Ceramilux®

CLEANING

To remove stains such as from hard water and dirt from the surface use non abrasive common detergents and rinse well. Products we suggest are: ACE gel cream, CIF gel, AIAX, apply with a soft sponge or cotton cloth. Avoid the use of abrasive detergents or abrasive sponges. Do not use aggressive chemical products such as acetone, trichloroethylene nor strong acids. Some products such as ink, cosmetics and dye, if in contact with the material for long periods of time, can stain the Ceramilux® surface. Avoid cigarette burns and do not cut on the surface.

Remedies for incidentally occurred damagesImproper use can cause visible defects on CERAMILUX surfaceIt is often possible to eliminate scratches, stains or splinters easily at home. If the gelcoat isn’t damaged totally in its depths, it will be possible to uniform the surface by using very fi ne sandpaper (800 - 1000 grain). To regain original brilliance use polish products (i.e. car bodies polish wil be ok).

TOXICITY


ECOLOGY



Ceramilux opacoCeramilux opaco is a 70% natural mineral charges (calcium carbonates and aluminium trihydrates) composite blended with 30% polyester resin. The matt gelcoat fi lm that covers the surface of the material (800 – 1000 μm) is of the acrylate polyester type. This kind of coating can be restored, as a Solid Surface material, with a Scotch Brite® abrasive sponge.

Ceramilux opaco is a very versatile material which allows the development of a lot of shapes: wash basins, shower trays, tabletops, in many colours.

Ceramilux opaco


CLEANINGDaily maintenanceLooking after Ceramilux opaco is quick and easy.Simply clean the surface with soapy water or any common detergent in order to remove most of the stains and dirt that may be deposited. Gel or abrasive detergents in particular are recommended, together with an abrasive sponge such as a Scotch Brite® one, making sure to properly rinse the area treated. The original mat fi nish, the distinguishing mark of Ceramilux opaco, will thus be maintained.

How to prevent damageThe surface has a good resistance to stains in general; nonetheless, the use of harsh chemical products such as acetone, trichloroethylene or strong acids or bases is not recommended. Some substances such as ink, cosmetics and dyes may, under extended contact with Ceramilux opaco, release colouring onto its surface. The same applies for lit cigarettes. All of these can easily be removed by following the suggestions below.

Removing stubborn stains, scratches and burnsCeramilux opaco can be repaired of surface damage such as scratches, cigarette burns and stubborn stains, restoring the surface to its original splendour, by following these simple instructions: for minor damage, the surface can be repaired using an abrasive Scotch Brite® sponge (3M registered trademark) and any common abrasive detersive. If the defect is still visible, repeat the operation this time using very fi ne-grain sanding paper.

TOXICITY

The product does not appear toxic to humans, animals or to the environment. The panels in fi bre wood, particle boards and plywood used conform to regulation EN120 CLASSE E1, with limited emission of formaldehyde.

ECOLOGY


PRODUCT DESCRIPTION



CORIAN®Corian® is a solid, non-porous surfacing material homogeneously composed of ±1/3 acrylic resin (also known as PolyMethyl MethAcrylate or PMMA), and ±2/3 natural minerals. These minerals are composed of Aluminium TriHydrate(ATH) derived from bauxite, an ore from which aluminium is extracted.Being inherently “renewable” because it is solid and homogeneous all the way through. Most damage, including severe impact, heat or chemical damage, can usually be repaired on site to restore the original, smooth, hygienic solid surface integrity.

SHOWER TRAYS WITH TEAK FOOTBOARD

TEAK BURMA FEQ (fi rst European quality) from Myanmar, is presented in a golden brown or dark brown colour,naturally seasoned.

BATHTUBS WITH WOOD COVERING

Finish Birch plywood with phenolic adesive veneered in wood essence.

CUSHION

Expanded polyurethane

Corian® sinks / shower trays / tubs


CLEANING *

Clean with a damp cloth or with common liquid detergents for domestic use. Particularly recommended are liquid detergents such as CIF® used with an abrasive sponge such as a SCOTCH BRITE® pad. Do not use aggressive chemical products such as acetone, trichloroethylene nor strong acids. Warning: Level sinks, shower trays and tubs.

Cleaning of wood coveringAvoid using common products for cleaning the wood which can damage the matt fi nish. Use exclusively the CLEANWOOD product provided by our company. Use a damp cloth with this product and distribuite evenly over the surface to clean. Avoid the use of abrasive sponges.

TOXICITY

The product does not appear toxic to humans, animals or to the environment. Only discard in appropriate disposals according to rules and regulations in your area.

ECOLOGY


WARNING

The sinks, shower trays and tubs must be installed levelled.

PRODUCT DESCRIPTION


Common household spills Procedura

Everyday cleaning. A. B. C. E.

Vinegar, coffee, tea, lemon juice, vegetable, dyes, ketchup. grease, fat and oil residues A. B. C. D.

Water scale, soap, minerals. A. B. F.

Pollen, saffron, a light scratch, cigarette burns, shoe polish, Ink, marker pen. A. B. C. E.

Mercurochrome, blood, red wine, perfume. A. B. C. D. E.

Nail varnish spills. A. B. C. G.

Iron or rust. A. B. C. H.

Iodine, mildew. A. B. C. E.

A Remove excess with a soft cloth

B Rinse surface with warm water and dry with a soft cloth

C Use a damp cloth and a mild cream abrasive cleanser. (e.g. Jif active, Bar Keepers Friend);

D Use an abrasive plastic scouring pad (e.g. Scotch-Brite® type) and rub over the stain with detergent or an ammonia based hard-surface cleaner (e.g. Flash, Mr. Muscle, Comet)

E Use an abrasive plastic scouring pad (e.g. Scotch-Brite® type) and rub over the stain with some bleach** (Javel). Rinse several times with warm water and dry with a soft cloth **

F Use an abrasive plastic scouring pad (e.g. Scotch-Brite® type) and rub over the stain with standard household lime-scale remover or vinegar (e.g.Viakal type). Rinse several times with warm water and dry with a soft cloth

G Use an abrasive plastic scouring pad (e.g. Scotch-Brite® type) and rub over the stain with non-acetone based remover. Rinse several times with warm water and dry with a soft cloth

H Use an abrasive plastic scouring pad (e.g. Scotch-Brite® type) and rub over the stain with a metal cleaner or rust remover. Rinse several times with warm water and dry with a soft cloth

* Clean using a circular motion** La candeggina può scolorire il Corian® se non è rimossa completamente

risciacquare con abbondante acqua


PRODUCT DESCRIPTION


COLDSTONE TOP

BONDED LEATHER

Malts with a polymer-noble base in aqueous emulsion and natural inert fi llers absent from cement and resin epoxy applied on a panel of medium density fi ber board.

CLEANINGIt is advisable to use moderate amount of neutral non aggressive alkaline detergents or preferably with a quaternary ammonium salt base on a microfi ber cloth performing circular motions. Exert moderate pressure and do not rub vigorously.To disinfect use non aggressive disinfectants, should be diluted with warm water.After each cleaning process it is advisable to wash down the top with abundant water.Do not use cleaning solvents and concentrated acids.

WARNINGDo not use abrasive sponges.The surface should not come in contact with substances or bodies at high temperatures.Avoid uncontrolled and or prolonged exposure with liquids and dry with a soft cloth after each use.

COLDSTONE tops can be permanently damaged with the following products:

• Sodium Hydroxide• Sodium Hypochlorite (bleach)• Methylene Blue• Ethyl alcohol and alcoholic solutions with a alcohol content

superior to 10% (for example perfumes, colognes..)• Methylene chloride• Acetone and solvents for nails• Organic dyes and solutions containing organic dyes (for

example hair dye, coffee, make-up..)

In the case the surface should come in contact with any of the above mentioned it is advisable to quickly and thoroughly rinse with any of the mild detergents listed prior and use abundant water.

The warranty of the product is void in the case of exposure to any substance not specifi ed in the above list or due to improper use of the product.

ECOLOGYOnly discard in appropriate disposals according to rules and regulations in your area.



PRODUCT DESCRIPTION


Leather mat

BONDED LEATHER

Bonded leather is composed by 80% of grind and mixed leather with 20% of resins and ecological grease.

The different stitches are in 100% polyester..

NEOPRENE

Neoprene is the trading name for a family of synthetic rubbers based on polychloroprene ( polymer version of chloroprene)

The main characteristics of neoprene are fl exibility, resistance to cuts and treading, resistance to external agents aging and heat and furthermore this product results being inert towards most of the chemical agents, oils, solvents and liquids in general.

CLEANING

Bonded leather is waterproof, easy to wash with a wet sponge with water and natural soap.Do not use abrasive sponge and solvents of any kinds.Keep away from heat.

TOXICITY


ECOLOGY



Alabaster


AlabasterAlabaster is a natural stone and as such varies in shades and veins like all natural materials. Due to these characteristics of the material, each piece is unique and unrepeatable.Since it is natural stone worked by hand, any imperfections in the surface and small unevenness found on the surface shall be treated as a valuable characteristics of the craftsmanship.

EFFECTED TESTS

Waterproofi ng (UNI EN 1925:2000): from 2,46 to 0,3

Impact: 6 (excess of certain types of marble)

Water / Oil Repellent: contact test during 4 consecutive hours: No problems for water, oil, liquid soap. Slight stain for ethyl alcohol.

Stain Resistance: contact test during 126 consecutive hours: No problems for coffee, lemon or coke.

Heat Resistance: 80° C

CLEANING: Cleaning can be done using the product “CIF® cream” with a soft sponge.

Caution: Do not use sponges and / or emery paper, nor acids which could irreparably scratch your sink.If metal or non objects of signifi cant weight should accidentally fall on the item it may permanently damage your sink.

TOXICITY


ECOLOGY



Stone sinks and tubs


PRODUCT DESCRIPTION

Crystal lamps / sinks


SINK / TUB

Natural stoneGiven the natural characteristics of the stone, each piece can present veins, tonality differences, mineral intrusion or stucco-work.

CLEANING

Once installed, we advise a waterproofi ng treatment without modifying the original aspect.For treatment use product Clean Stone provided (see spec sheet).

Apply with a soft cloth or brush, treat the entire surface and wait 30 minutes for the product to have taken effect after which apply the second coat. Remove eventual residue of dust with a dry cloth.

Not advisable are strong abrasive cleaners, grease or calcareous removers, acids and alcohol.

TOXICITY


ECOLOGY


CRYSTAL

Crystal has a lead content of 26,06%.Each sink is made exclusively by hand and blown by mouth. Eventual apparent defects such as air bubbles or differences in thickness are due to the artistic and manual elaboration.

LAMP BASE

Stainless steel with levellers in chrome plated brass and rubber ends.

ELECTRICAL WIRING

Class A

CLEANING

Clean with a soft damp cloth.Avoid the usage of solvents, abrasive and acidic products.

TOXICITY


ECOLOGY




Shower enclosures


PRODUCT DESCRIPTION

Tap ware


GLASS

Tempered clear fl oat glass 8 mm. (UNI EN 12150-1)Float glass ultra clear 8mm. Tempered (UNI EN 12150-1)Acid fi nish fl oat glass 8 mm tempered (UNI EN 12150-1)

STRUCTURE

Stainless steel complete with silicone trim

CLEANING

Clean with diluted acetyl alcohol or commonly used glass cleaners.We advise after usage to dry the surfaces with a soft cloth.

TOXICITY


ECOLOGY


TAP WARE

Chromed brassBIKAPPA series

Stainless SteelAYATI series

CLEANING

Clean with warm water and non abrasive detergents.Do not use abrasive sponges which could damage the surface.Hard water may be removed by emerging for several hours the sink aerator in vinegar.

TOXICITY


ECOLOGY




POLISHED OR BEVELLED EDGE MIRROR

Silver plated fl oat glass 5 mm thick

FRAMEStainless steel or pre-painted zinc coated steel

MIRRORED CABINETS

Lacquered version

StructureParticle board 18 mm. thick laminated and bordered grey fi nish, lacquered externally with polyurethane paints.

FrontsMedium density fi breboard lacquered with polyurethane paints.

Back panelWood fi bre panel laminated grey

Wood version

Structure and frontsOak veneered poplar with continuous grain bordering and open pore painted.

Back panelOak veneered poplar plywood and open pore painted.

Mirrors with plywood frameFrame in oak veneered poplar with continuous grain bordering and open pore painted.

Mirrors with a wood frameSolid wood frame open pore painted or lacquered with paints with a polyurethane base.

Mirrors with stainless steel frameFrame in stainless steel.

MIRRORS WITH NEON LIGHTINGMirrors with stainless steel frame and neon lighting class IP21.

MIRRORS WITH LED LIGHTINGMirrors with stainless steel frame and led lighting class IP21.

LACQUERED MIRRORSMirrors lacquered with polyurethane paints.


DUROGLASS MIRRORSPatented method.

GLASS SHELF8 mm and 15 mm fl oat glass.

Mirrors


CLEANING

Clean with diluted acetyl alcohol or commonly used glass cleaners.Avoid the usage of solvents, abrasive and acidic products.

TOXICITY

The product does not appear toxic to humans, animals or to the environment. The panels in fi bre wood, particle boards and plywood used conform to regulation EN120 CLASSE E1, with limited emission of formaldehyde.

ECOLOGY


PRODUCT DESCRIPTION



Accessories


PRODUCT DESCRIPTION

JUST SERIES

Metal partsStainless steel

Acrylic partsNeutral polyester resin + coloured paste

Wood parts6 tenths wood veneered poplar plywood with phenolic adhesive, continuous grain bordering and open pore painted.

TAPE SERIES

Metal partsStainless steel

Corian® parts CORIAN® is an advanced of Aluminium Tri-Hydrate (ATH) and acrylic (PMMA) produced by DuPont

TENSOStainless steel

STEELStainless steel

SHELF

Wood version6 tenths wood veneered poplar plywood with phenolic adhesive, continuous grain bordering and open pore painted.

Lacquered versionMedium density fi breboard lacquered withpolyurethane paints.

LEGO20 mm fl oat glassSupports in chrome plated brass

TENAX8 mm fl oat glassSupports in chrome plated metal

BASIC -HOOKStainless steel

TANDEM - LINKStainless steel

TANDEM - UPStainless steel

CLEANING

Stainless steel.Clean with diluted acetyl alcohol.

Acrylics:Clean with water or neutral detergents. Use a dry cotton cloth.Do not use acetone based solvents.

CORIAN®:Clean® with a damp cloth or commonly used cleaners.Particularly recommended are liquid detergents such as CIF® used with an abrasive sponge such as a SCOTCH BRITE® pad. Do not use acetone based solvents.

Plywood:Clean the furniture with a soft cloth or damp non abrasive sponge.Do not use wood cleaners which can damage the matt fi nish. Exclusively use the product provided.

Glass:Clean with diluted acetyl alcohol or commonly used glass cleaners.Avoid the usage of solvents, abrasive and acidic products.

TOXICITY

The product does not appear toxic to humans, animals or to the environment.The panels in fi bre wood, particle boards and plywood used conform to regulation EN120 CLASSE E1, with limited emission of formaldehyde.

ECOLOGY




PRODUCT DESCRIPTION


MAINTENANCE OF STAINLESS STEEL SURFACES PRECAUTION

Stainless steel is an alloy composed by iron and carbon which combines the typical mechanical properties of carbon steels and peculiar characteristics of resistance to corrosion.

It is defi ned stainless steel because it resists to corrosion thanks to a thin oxide fi lm that forms on its surface.

The fi lm becomes a natural barrier against the effects of atmospheric agents.

It is therefore wrong to think that stainless steel is indestructible and does not corrode, stainless steel can also suffer considerable damage if not treated with care.

Its strength and durability, are closely related to proper use, good maintenance and use of appropriate cleaning products and materials in order to preserve the original characteristics.

Oxidation spots, limestone deposits and rust can appear on the surfaces if they are not cleaned and maintained properly.

MAIN CAUSES OF OXIDATION

Ferrous residuals left to settle on damp surfaces (not dry) carried by water or products used for cleaning (scrapers, steel wool, etc.)Limestone it contributes to weaken the steel in some spots or in areas where it has accumulated.

Encrustations they can accumulate in the less accessible parts.

Cleaners containing chlorine or ammonia not properly rinsed.

Salt if not dissolved in hot water or as dry residue of evaporated liquids etc..

It is important to know that the use of steel wool or similar tools used for removing solid residues, may leave microscopic particles that detach from these tools and remain deposited on the surface. For contact, these particles, trigger a rapid irreversible corrosion process or hardly restorable if action is not taken in a short time (an iron particle left in a humid environment takes a few hours to cause a major trigger of corrosion);

In order to avoid limestone deposits and encrustations, it is recommended to wash the product with a solution of warm water and vinegar, or with liquid soap diluted in water. Then dry with a soft cloth.

The use of detergent products containing chlorine, such as bleach or similar products normally available on the market must be avoided because they can produce serious effects of corrosion if not abundantly, quickly and appropriately rinsed;

The contact or vapors from acid (muriatic acid / hydrochloric acid) or alkaline (sodium hypochlorite / bleach ) or ammonia, used directly or diluted/contained in ordinary detergents for cleaning and sanitation of fl oors, tiles and washable surfaces, may cause a corrosive / oxidizing process on stainless steel;

Do not place on the surface of stainless steel rags, cleaning clothes, sponges or anything similar, imbued with common detergents containing chlorine or ammonia before having them neutralized and rinsed properly from this “contact” with a neutral detergent;

Rinse thoroughly and dry the surface.

WARNING Failure to observe these precautions will void the warranty.

STAINLESS STEEL


PRODUCT DESCRIPTION


MATERIALS USED INSTRUCTIONS FOR USE AND MAINTENACE

Transfer paper digitally printed with solvent based inks composed of acrylic vinyl and polyurethane resins containing alloys, anti-foamers, matte and surfactants with liner made of polyester transparent support 50 MY.C2: transparent glue made from synthetic resins to prepare the

surfaces to be decorated.F3: transparent opaque fi nish quartz based, made from epoxy resin

and polyamide in aqueous dispersion with relative catalyst.F6: transparent opaque fi nish composed of water based acrylic

emulsion polyurethane with relative catalyst.

The application of the frescoes on the surface must be strictly performed by highly trained personnel instructed by the company.

Methods of handling and storageDo not open the package and extract its contents until installed. Keep in a dry well ventilated area away from sources of heat at a temperature between 15°C and 28°C avoiding direct sunlight and making sure to not load weight on the packages.The application and fi nishing products must be used within 12 months.Handle packages with care avoiding shocks.

APPLICABILITY OF THE FRESCOThe Fresco can be applied to any fl at surface and on the front of sinks that are encased in the wall. In the case of different surfaces contact the company.The fresco can be applied on walls with shaved smooth plaster (stucco), textured plaster or bearing a coat of medium grain primer instead of the plaster.The fresco must be applied on a strong and consistent surface which do not tend to dust, chalk or crack. Do not apply on surfaces that are dirty, have cracks or several coats of paint mildew or humidity stains.Eventual imperfections in the decoration due to an uneven surface (roughness and imperfections in the plaster, stucco, patches, stains, etc.) cannot be grounds for claims.

WARNING: The fi nish F6 is a water repellent fi nish but cannot stay in long contact with water.

PREPARATION OF WALLS TO BE FRESCOED.The walls to be frescoed should be painted with white washable acrylic paint (do not use tempera paints) at least 48 hours before applying the fresco.Further informationIn the 24 hours following the application or until completely dry, carefully avoid that the surface become in contact with foreign objects.

CLEANINGDo not use aggressive detergents or or products for cleaning.In the case of application with F3, clean with a soft damp cloth.In the case of application with F6, clean with a soft damp cloth.

ECOLOGYAfter installation do not dispose of the products in the environment but in the manner prescribed by your municipal waste department.

FRESCO PRODUCT INFORMATION SHEET


SCHEDE PRODOTTO

Warning:The current product information complies with law n.126 of the 10th of April 1991 “Regulations for consumer information” and to ordi-nance n.101 of the 8th of February 1997 “Fulfi lment Regulations”


INFORMAZIONI ENERGETICHE - ENERGETIC INFORMATION - NERGIEEFFIZIENZKLASSE INFORMATIONS ÉNERGÉTIQUES - INFORMACIONES ENERGÉTICAS - ИНФОРМАЦИЯ ОБ ЭНЕРГОЭФФЕКТИВНОСТИ

Articoli muniti di lampade a led integrate di classe energetica A non sostituibili - Articles provided with integrated led bulbs of energy class A not replaceable - Diese Artikel enthalten eingebaute nicht austauschbare LED- Lampen der Energieklasse A - Articles munis des lampes aux LED intégrées de classe énergétique A non remplaçables - Artículos equipados con lámparas led de clase enrgética A no sustituibles Артикулы, оборудованные встроенными незаменяемыми светодиодными лампами класса энергоэффективности А

Articoli venduti con lampade di classe energetica C e compatibili con lampade di classe energetica C e D - Articles sold with bulbs of energy class C and compatible with bulbs of energy classes C and D - Diese Artikel werden mit Leuchten Energieklasse C verkauft und sind kompatibel mit Leuchten der Energieklassen C und D - Articles vendus avec des ampoules de classe énergétique C et compatibles avec des ampoules de classe énergétique C et D - Artículos vendidos con lámparas de clase energética C y compatibles con lámparas de clase energética C y D - Артикулы, продаваемые в комплекте с лампами класса энергоэффективности С и совместимые с лампами класса энергоэффективности C и D

Articoli venduti con lampade di classe energetica A e compatibili con lampade di classe energetica A+ e A - Articles sold with bulbs of energy class A and compatible with bulbs of energy classes A+ and A - Diese Artikel werden mit Leuchten Energieklasse A verkauft und sind kompatibel mit Leuchten der Energieklassen A+ und A - Articles vendus avec des ampoules de classe énergétique A et compatibles avec des ampoules de classe énergétique A+ et A - Artículos vendidos con lámparas de clase energética A y compatibles con lámparas de clase energética A+ y A - Артикулы, продаваемые в комплекте с лампами класса энергоэффективности А и совместимые с лампами класса энергоэффективности А+ и А

Articoli venduti con lampade di classe energetica A e compatibili con lampade di classe energetica A++, A+ e A - Articles sold with bulbs of energy class A and compatible with bulbs of energy classes A++, A+ and A - Diese Artikel werden mit Leuchten Energieklasse A verkauft und sind kompatibel mit Leuchten der Energieklassen A++, A+ und A - Articles vendus avec des ampoules de classe énergétique A et compatibles avec des ampoules de classe énergétique A++, A+ et A - Artículos vendidos con lámparas de clase energética A y compatibles con lámparas de clase energética A++, A+ y A - Артикулы, продаваемые в комплекте с лампами класса энергоэффективности А и совместимые с лампами класса энергоэффективности А++, А+ и А

Etichette energetiche disponibili su www.antoniolupi.it - Energy lables available on www.antoniolupi.it - EU- Energielabel- Etikett verfügbar auf www.antoniolupi.it Etiquette- énergie disponible sur www.antoniolupi.it - Etiquetas energéticas disponibles en www.antoniolupi.it - Энергетические этикетки доступны на сайте www.antoniolupi.it

LIGHT1LIGHT2LIGHT3RAGGIOSQUADRO36

OBLÒ2OBLÒ3OBLÒ50OBLÒ150

ASPI1ASPI2ASPI3ASPI4ASPI50ASPI75CIOK1CIOK2CIOK3CIOK4

CIOK50CIOK75CROSS1CROSS2CROSS3CROSS4CROSS50CROSS75CURVA_UPCURVA_DOWN

SFOGLIA175SPIO1SPIO2SPIO3SPIO4SPIO5SPIO50SPIO75SPIO150NSPIO175N

SPIO250SPIO275VANESIO1VANESIO2VISOVISO2

FLASH50NFLASH75NFLASH90NFLASH100NFLATFLÒ1FLÒ2FLÒ3FLÒ6FLÒ50

FLÒ75FOGLAMPO50NLAMPO75NPILL1PILL2PILL3PILL4PILL50PILL75

ASPI1WASPI2WASPI3WASPI4WASPI50WASPI75WCIOK1WCIOK2WCIOK3WCIOK4WCIOK50WCIOK75WCROSS1WCROSS2WCROSS3WCROSS4WCROSS50WCROSS75WCUPIDO72LCUPIDO126LDAMA75LDAMA75WDAMA108LDAMA108W

DIVO220LDIVO220WFLASH50LFLASH50WFLASH75LFLASH75WFLASH90LFLASH90WFLASH100LFLASH100WFLASH125LFLASH125WFLASH150LFLASH150WFLATWFLÒ1WFLÒ2WFLÒ3WFLÒ6WFLÒ50WFLÒ75WFOGWFUORIMETEO10FUORIMETEO20

FUORIMETEO20CIEGAIEGAWLAMPO50LLAMPO50WLAMPO75LLAMPO75WMANTRA150MANTRA175MANTRA190MANTRA250MANTRA275MANTRA290METEO1METEO2METEO2CMETEO3CMETEO_RAMETEOXXLOIO3BOIO3LOIO4BOIO4LOVIDIO50L

OVIDIO50WOVIDIO75LOVIDIO75WPERIPLOPILL1WPILL2WPILL3WPILL4WPILL50WPILL75WRIGA54RIGA63RIGA72RIGA81RIGA90RIGA99RIGA108RIGA117RIGA126RIGA135RIGA144RIGA153RIGA154RIGA162

RIGA163RIGA171RIGA172RIGA180RIGA181RIGA189RIGA190RIGA198RIGA199RIGA207RIGA216RIGA1108RIGA1117RIGA1126RIGA1135RIGA1144RIGA1153RIGA1162RIGA1171RIGA1180RIGA1189RIGA1198RIGA1207RIGA1216

RIGA_S154RIGA_S163RIGA_S172RIGA_S181RIGA_S190RIGA_S199RIGA_S1108RIGA_S1117RIGA_S1126RIGA_S1135RIGA_S1144RIGA_S1153RIGA_S1162RIGA_S1171RIGA_S1180RIGA_S1189RIGA_S1198RIGA_S1207RIGA_S1216SEGRETOSEGRETO1SFOGLIA75LSILENZIOLSOFFIOL

SOTTOQUADROSPIO1WSPIO2WSPIO3WSPIO4WSPIO5WSPIO50WSPIO75WSPIO150LSPIO150WSPIO175LSPIO175WSPIO250WSPIO275WSTRAPPOLTALK50LTALK50WTALK75LTALK75WVANESIO1WVANESIO2WVISOWVISO2W


INSTALLATION GUIDELINES PRODUCT DISCRIPTION ......INSTALLATION GUIDELINES MAINTENANCE PRODUCT DISCRIPTION WARNING!!! We decline all responsibility and eventual inaccuracy contained

Documents