INST99-8205 · 2010. 7. 11. · The 2002-2005 Kia Sedona and the 2001-2003 Kia Spectra will use the tabs marked by the number 2 on the brackets. Note: For the 2001-2003 Kia Spectra
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.
1
Unclip and remove entire panel sur-rounding radio and climate controls.(Figure A)
2
2004-2006 KIA SPECTRA
Remove (4) Phillips screws securingradio. (Figure B)
3
A
B
95-1005 KIT ASSEMBLY
6
You will need to cut and remove the tabs according to the chart and refer-ring to the diagram below:
The 2002-2005 Kia Sedona and the 2001-2003 Kia Spectra will use the tabsmarked by the number 2 on the brackets. Note: For the 2001-2003 KiaSpectra proceed to page 9 for Final Assembly.
The 2002-2005 Kia Rio will use the tabs marked by the number 3 on thebrackets.
The 2003-2006 Sorrento LX and the 2004-2006 Kia Spectra will use the tabsmarked by the number 1 on the brackets.
1 2 3 123
L R
TAB REMOVAL INSTRUCTIONS
95-1005 KIT ASSEMBLY
7
2
A
Slide the DDIN radio unit into thetrim plate bracket assembly andsecure the unit to the kit using thescrews supplied with the head unit.(Figure B)
Slide the appropriate bracket intothe trim plate aligning the holes inthe trim plate to the clips on thebracket. (Figure A)
1
B
DOUBLE DIN HEAD UNIT PROVISION
95-1005 KIT ASSEMBLY
8
2
A
Slide the stacked ISO DIN units intothe trim plate bracket assembly andsecure the units to the kit using thescrews supplied with the head units.(Figure B)
Slide the appropriate bracket intothe trim plate aligning the holes inthe trim plate to the clips on thebracket. (Figure A)
1
B
STACKED ISO DIN HEAD UNIT PROVISION
9
95-1005 FINAL ASSEMBLY
Place the 95-1005 into dash opening, do not bolt in. (Figure A)1
Snap trim bezel back into place and pressure fit kit into place.2
2001-2003 KIA SPECTRA
Reassemble dash in the reverse order of dash disassembly on page 4beginning with step #3.
3
A
10
FINAL ASSEMBLY1 Locate the factory wiring harness in the dash and make the connection as shown.
Metra recomends using the proper mating adapter and making the connections asshown. (Isolate and individually tape off the ends of any unused wires to preventelectrical short circuit.)
2 Re-connect the negative battery terminal and test the unit for proper operation.3 Reassemble radio and dash assemblies in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
Make wiring connections using the EIA color code chart shown below and the instructions included with the headunit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individuallytape off ends of any unused wires to prevent electrical short circuit.
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-) . . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.All colors may not be present on all leads due to manufacturer’s specifications.