INFINITE 7 - 8 POWER AMPLIFIERS OWNER'S MANUAL
Dec 14, 2015
OWNER'S MANUAL
Technical and design specifications are
subject to change without notice
INFINITE 7 - 8POWER AMPLIFIERS
Page 3
Infinite Series Power Amplifiers
TO PREVENT ELECTRIC SHOCK, DO NOT REMOVE TOP OR BOTTOM COVERS. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. DISCONNECT POWER CORD BEFORE REMOVING REAR PANEL COVER TO ACCESS GAIN SWITCH.
Shock Hazard - Do Not EnterChoc Hasard - N*entrentSchocke Hazard - Test Nicht BetreteUrto Hazard - Do Non Entrano
WARNINGTO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT EXPOSE THISEQUIPMENT TO RAIN OR MOISTURE!
Magnetic FieldCAUTION: Do not locate sensitive high-gain equipment such as preamplifiers or tape decks directly above or below this unit. Because this amplifier has a high power density, it has a strong magnetic field which can induce hum into unshielded devices that are located nearby. This field is strongest just above and below the unit. If an equipment rack is used, we recommend locating the amplifier(s) at the bottom of the rack and the preamplifier or other sensitive equipment at the top.
The lightning bolt triangle is used alert the user to the risk of electric shock
The exclamation point triangle is used to alert the user to important operating and/or maintenance instructions.
Printed on recycled paper.
IMPORTANTTHE PRODUCT REQUIRESCLASS 2 OUTPUT WIRING.
Page 4
Infinite Series Power Amplifiers
Features
Rugged, touring grade chassis. E.I.A. Standard 19" (48.3cm) rack-mountable.
Ultra reliable Infinite series 'Logic Output Stages' provide maximum stability even into 2 ohm loads.
Relay control power switch with soft start for loudspeaker protection.
Stereo, parallel and bridge modes for optimal load matching.
Anti Clip limit protection prevents harmful signals from damaging loudspeakers.
Output Device Emulation circuitry helps keep the amplifier working under extreme conditions.
High damping factor provides greater control over low frequency drivers for a clean and accurate low end.
Balanced XLR inputs with direct XLR outputs.
Complete protection against shorted outputs, mismatched loads, overheating and DC input/output.
Efficient heat sinks and self-contained forced air cooling system.
One year warranty and guarantee.
Precautions
Although your amplifier is protected from external faults, the following safety precautions are recommended:
1. Do not change the position of the stereo/mono mode switch unless the amplifier is first turned off.
2. There are important differences between the Stereo, Parallel and Bridge modes. Please refer to page 7 for a detailed description of the different modes and there uses.
3. Switch off the amplifier or turn down the inputs before connecting to the in/out XLR's.
4. Do not short the ground lead of an output cable to the input signal ground. This will form a ground loop and may cause oscillations.
5. Do not connect both channels positive outputs together in parallel or stereo modes. And never connect any channels positive output to chassis ground.
6. Do not operate the amplifier from AC mains in excess of 10% variation above or below the selected line voltage, and only at the specified line frequency.
Page 5
Infinite Series Power Amplifiers
Front Panel
1.Power Switch To turn the amplifier ON or OFF.2.Level Controls To control the output levels.3.Power LED The Power LED shows that the amplifier has been turned on.4.Signal LEDs When illuminated the LEDs indicate an audio signal is present at the channel's output.5.Limit LED The Limit LED indicates when the limiter is active. The limiter circuit examines the audio signal to prevent the amplifier from clipping6.Protect LED The protect LED lights up when the amplifier detects dangerous subsonic frequencies, DC or thermal overload. 7.Bridge LED Indicates when the amplifier is in bridge mode.
1
3 4
5
6 2
7
acoustics
BRIDGE POWER
Page 6
Infinite Series Power Amplifiers
1
34
56 27
8
Rear Panel
1.Input XLR The input impedance of the balanced XLR is 20Kohms.2.Output XLR Linked output from the inputs3.Stereo, Parallel & Bridge Mode Switch Selects Stereo, Parallel or Bridge Mode. See notes below.4.Limiter switch Turns the limiter on and off. Best left in the on position.5.CH1 Speakon Outputs In stereo mode use 1+ and 1-. CH2 output is also on 2+ and 2-6.CH2 Speakon Outputs In stereo mode use 1+ and 1-7.Bridge Speakon Outputs In bridge mono mode use 1+ and 1-. Min 4 ohm load8.Power Cable AC power in 230 VAC 50/60 Hz
CautionRisk Of Electric Shock
Do Not Open
Warning-To Reduce The Risk Of FireOr Electrical Shock, Do Not Expose This Equipment To Rain Or Moisture.No User Serviceable Parts Inside Refer Servicing To Qualified Service Personal
Speaker Output:Class 2 Wiring PermittedClass 1 Wiring RequiredIn Bridge Mono Connection
Output AssignmentOut1:Pin1+:Signal Ch1 Pin1-:Ground Ch1 Pin2+:Signal Ch2 Pin2-:Ground Ch2Out2:Pin1+:Signal Ch2 Pin1-:Ground Ch2 Pin2+ Pin2-
Bridge Mono Output
Pin2+:GroundOut1:Pin1+:Signal
SERIAL NO.:
Stereo
Bridge
Mode
Parallel
Direct Out
CH2CH1
Input
Limit
OffOn
Page 7
Infinite Series Power Amplifiers
Stereo, Parallel & Bridge Modes
Stereo mode
Input 1 is the input to CH1's output and input 2 is the input to CH2's output. Just like a normal stereo amp.
Bridge mode
Connect to input 1 only and use the two dedicated bridge output speakons. Minimum impedance in Bridge mode must be 4 ohms, so one 8 ohm load from each speakon. Be aware that each 8 ohm load will receive 3700 watts rms. The amplifier is mono when running in bridge mode and both CH1 and CH2 bridge output speakons output the same signal.
Parallel mode
Input 1 is linked to input 2. Connect to input 1 only, the same signal will output from both CH1 and CH2 outputs. The amplifier is mono in this mode. The same effect could be achieved by connecing to input 1 and connecting input 1's link out to input 2 with a short XLR lead.
In parallel mode CH 1's level control is used to control the level for both outputs.
Note the parallel mode on Infinite amplifers is not like the parallel mode on some amplifers that allow you to drive into very low impedances. Parallel mode on the Infinite series amps just makes both inputs receive the same signal.
4
8
4
8
1kHz 1kHz10Hz-20kHz 10Hz-20kHz
0.1%THD+N 0.1%THD+N 0.1%THD+N
Infinite 7
Mode
Stereo(Both CH Driven)
Bridge Mode(Both CH Driven)
Impedance RMS Output Power per ch
0.1%THD+N
both ch - 2 ohms 42 AmpsMaximum Current Draw
RMS Output Power per ch
Infinite 8
Maximum Current Drawboth ch - 2 ohms 29 Amps
1500 1490 2400 2388
900 890 1300 1290
4600 4585 7400 7386
3000 2987 4800 4787
TECHNICAL SPECIFICATIONS For Infinite models 7 - 8
Page 8
Infinite Series Power Amplifiers
Dimensions : 48.3 cm (19") wide, 13.5 cm (5.3") high and 44.9 cm (17.7") deep.
Weight:
Infinite 7 : 31.5 Kg (69.4 pounds) net. 35.0 Kg (77.2 pounds) shipping weight. Infinite 8 : 37.5 Kg (82.6 pounds) net. 41.0 Kg (90.4 pounds) shipping weight.
TECHNICAL SPECIFICATIONS
S/N 20Hz-20kHz, ref full output
20kΩ balanced
LIMITER COMPRESSION RATIO
INPUT SENSITIVITY
FREQUENCY RESPONSE ref.100W@8Ω 20Hz - 20kHz +0.1 dB / -0.2 dBTOTAL HARMONIC DISTORTION (THD)
230 VAC 50/60Hz +/- 10%VOLTGE RANGE
AMPLIFIER PROTECTION
1.0 Vrms
CROSSTALK
SLEW RATE
CMRR
INPUT IMPEDANCE
DAMPING FACTOR 1kHz and Below
CONNECTORS
COOLING
Infinite 7 45V/us - Infinite 8 20V/us
20:1Input: balanced XLR output: Speakon
Variable speed fans
Full short circuit, open circuit, thermal, ultrasonic, and RF protection, stable into reactive or mismatched loads
0.01%
>90dB>70dB
Infinite 7 >800 - Infinite 8 >600
103 dB
For Infinite models 7 - 8
Page 9
Infinite Series Power Amplifiers
ServiceThis unit has very sophisticated circuitry and should only be serviced by a fully trained technician.
To prevent electric shock, do not remove covers No user serviceable parts inside Refer servicing to a qualified technician
Worldwide Service
Service may be obtained from your local authorised service centre. To obtain service, simply present your sales receipt as proof of purchase along with the defective unit to an authorised service centre. They will handle the necessary paperwork and repair. Remember to transport your unit in the original factory packaging.
1. When sending an Infinite Series product to an authorised service centre for service, please write a detailed description of the fault and list any other equipment used in conjunction with the faulty product. Send the fault description with the faulty product, do not send it separately.
2. Ensure safe transportation of your unit to the authorised service centre. Ship it in the original factory packaging if possible.
3. Do not ship the unit in any kind of rack. Ignoring this warning may result in extensive damage to the unit and the equipment rack. Accessories are not needed. Do not send the instruction manual, cables or any other hardware.
4. Before returning your faulty product for repair, please remember to get a return authorisation number from the dealer whom you purchased your product from. Failure to do so could delay the repair of your product.
Warranty Registration
Please take time to fill out the warranty registration form at the back of this manual and return it to Void Acoustics.
Page 10
Infinite Series Power Amplifiers
LIMITED WARRANTY THE WARRANTYFor a period of one (1) years from the date of delivery to the original purchaser (as shown on the original invoice or sales receipt), Void Acoustics (hereinafter "Void") warrants to the ORIGINAL OWNER of each new Infinite Series product (provided it was purchased at an Authorised Void Dealer) that it is free of defects in materials and workmanship and that each product will meet or exceed all factory published specifications for each respective model. Void agrees to repair or replace (at its discretion) all defective parts at no charge for labour or materials; subject to following provisions:
WARRANTY VIOLATIONSVoid shall take no responsibility for repair or replacement as specified under this warranty, if the damaged product has been subject to misuse, accident, neglect or failure to comply with normal maintenance procedures; or if the serial number has been defaced, altered or removed. Nor will Void accept responsibility for, or resulting from, improper alterations or unauthorised parts or repairs. This warranty does not cover any damage to speakers or any other consequential damage resulting from breach of any written or implied warranty.
VOID WARRANTY PROVISIONSVoid will remedy any defect, regardless of the reason for failure (except as excluded ) by repair, or replacement. Void will remedy the defect and ship the product within a reasonable time after receipt of the defective product at an Void Authorised Service Centre.
TO OBTAIN WARRANTY SERVICEIn the event that a Void product requires service, the Owner must contact Void or an Authorised Void Service Centre to receive an R.A.N. (Return Authorisation Number) and instructions on how to return the product to the Void Authorised Service Centre, or to the factory. Void (or its Authorised Service Centre) will initiate corrective repairs upon receipt of the returned product. Please save the original carton and all the packing materials in case shipping is required. All products being returned to the factory or service centre for repairs must be shipped prepaid.
If the repairs made by Void or the Void Authorised Service Centre are not satisfactory, the Owner is instructed to give written notice to Void. If the defect or malfunction remains after a reasonable amount of attempts by Void to remedy the defect or malfunction, the Owner shall then have the option to elect either a refund or replacement of said Void product free of charge. The refund shall be an amount equal to but not greater than the actual purchase price, not including any taxes, interest, insurance, closing costs and other finance charges (minus reasonable depreciation on the product). If a refund is necessary, the Owner must make the defective or malfunctioning product available to Void free and clear of all liens or other restrictions.
MODIFICATIONS OF EQUIPMENTVoid reserves the right to modify or change equipment (in whole or part) at any time prior to delivery thereof, in order to include therein electrical or mechanical improvements deemed appropriate by Void, but without incurring any liability to modify or change any equipment previously delivered, or to supply new equipment in accordance with any earlier specifications.
DISCLAIMER OF CONSEQUENTIAL AND INCIDENTAL DAMAGES YOU, THE OWNER, ARE NOT ENTITLED TO RECOVER FROM VOID ANY INCIDENTAL DAMAGES RESULTING FROM ANY DEFECT IN THE VOID PRODUCT. THIS INCLUDES ANY DAMAGE TO ANOTHER PRODUCT OR PRODUCTS RESULTING FROM SUCH A DEFECT.
WARRANTY ALTERATIONSNo person has the authority to enlarge, amend, or modify this Warranty. This Warranty is not extended by the length of time which the Owner is deprived of the use of product. Repairs and replacement parts provided pursuant to the Warranty shall carry only the non-expired portion of the Warranty.
THIS STATEMENT OF WARRANTY SUPERSEDES ALL OTHERS CONTAINED IN THIS MANUAL
War
rant
y C
opy
Ow
ner's Dat
e of
pur
chas
e
M
odel
Ser
ial n
umbe
r
Sup
plie
rs n
ame
and
addr
ess
Pos
t cod
e :
Tel :
Wh
at t
o d
o if
yo
ur V
oid
pro
du
ct n
eed
s re
pai
r
Con
tact
the
deal
er fr
om w
hom
you
pur
chas
ed th
e pr
oduc
tan
d ge
t a r
etur
n au
thor
isat
ion
num
ber.
Ret
urn
the
prod
uct (
pref
erab
ly in
its
orig
inal
box
) to
:
Voi
d A
cous
tics,
Uni
t 10B
, Daw
kins
Roa
d In
d E
st, P
oole
,D
orse
t, B
H15
4JD
, UK
.
Voi
d A
cous
tics
W
arra
nty
Thi
s V
oid
Aco
ustic
s pr
oduc
t is
guar
ante
ed a
gain
st d
efec
tsdu
e to
faul
ty m
ater
ials
or
wor
kman
ship
for
a pe
riod
of 3
ye
ars
from
the
date
of o
rigin
al p
urch
ase,
sub
ject
to th
efo
llow
ing
rest
rictio
ns.
1. T
his
war
rant
y is
onl
y va
lid in
the
coun
try
of p
urch
ase.
2. T
hat t
he p
rodu
ct h
as n
ot b
een
abus
ed o
r op
erat
ed in
conj
unct
ion
with
uns
uita
ble
or fa
ulty
app
arat
us.
3. T
hat t
he p
rodu
ct h
as n
ot b
een
mod
ified
, dis
asse
mbl
edor
tam
pere
d w
ith b
y an
y pe
rson
oth
er th
an V
oid
Aco
ustic
ste
chni
cal s
taff.
4. T
hat t
he p
rodu
ct h
as n
ot s
uffe
red
dam
age
in tr
ansi
t.
Do
not s
end
good
s to
Voi
d A
cous
tics
with
out f
irst o
btai
ning
a re
turn
aut
horis
atio
n nu
mbe
r.
Car
riage
cos
ts to
Voi
d A
cous
tics
will
be
retu
rned
to th
ecu
stom
er if
war
rant
y w
ork
prov
es n
eces
sary
. Pac
king
, in
sura
nce
and
frei
ght o
n th
e re
turn
jour
ney
will
be
paid
by
Voi
d A
cous
tics
or it
s au
thor
ised
dea
lers
.
Thi
s w
arra
nty
in n
o w
ay a
ffect
s yo
ur s
tatu
tory
rig
hts.
Voi
d A
cous
tics
Uni
t 10B
, Daw
kins
Roa
d In
d E
st, P
oole
, Dor
set,
BH
15 4
JDTe
l: +4
4 (0
)870
165
1 33
2
Fax:
+44
(0)
870
1651
352
Void AcousticsUnit 10B
Dawkins Road Ind Est
Poole
Dorset
BH15 4JD
UK
War
rant
y R
egis
trat
ion
Tha
nk y
ou fo
r pu
rcha
sing
this
Voi
d pr
oduc
t. P
leas
e co
mpl
ete
this
war
rant
y re
gist
ratio
n ca
rd a
nd c
ut o
ff th
is
part
and
sen
d it
to th
e ad
dres
s ov
erle
af.
Dat
e of
pur
chas
e
M
odel
Ser
ial n
umbe
r
Sup
plie
rs n
ame
and
addr
ess
Pos
t cod
e :
Tel :
Y
our
nam
e an
d ad
dres
s
Pos
t cod
e :
Tel :