DTMF BASED INDUSTRIAL AUTOMATION Presented by: B.VINAY KUMAR (407) A.MANOHAR REDDY (4A8) P.SANTHOSH (450) Internal guide:
Aug 28, 2014
DTMF BASED INDUSTRIAL
AUTOMATION
Presented by:
B.VINAY KUMAR (407) A.MANOHAR REDDY (4A8) P.SANTHOSH (450)
Internal guide: MS.Sameera snehanz
CONTENTS
INTRODUCTION
BLOCK DIAGRAM
WORKING
ADVANTAGES
APPLICATIONS
CONCLUSION
FUTURE SCOPE
INTRODUCTION
Industrial automation is the application of automation techniques
for the comfort and security of its parts.
In the present world of wireless technology every thing is going
to be digital and wireless, and the cell phone is the key player in
wireless technology today.
Today the working is going on how to develop remote devices
with out the presence of man and to reduce time and labor, and
our project belongs to that race and by using it we can control
any electronic devices through a cell phone, with one sms.
What is DTMF ?
• Dual tone multiple frequency signaling (DTMF).
• Multiple-frequency signaling consists of a combination of two tones with frequencies within the speech band.
• Each combination of two frequencies representing a single digit.
• The tones are in two groups : 1 Low Band 2 High Band
DTMF(Dual tone multiple frequency signaling)
Low High 1209 HZ 1336 HZ 1447 HZ 1633
HZ 697 HZ 1 2 3 A 770 HZ 4 5 6 B 852 HZ 7 8 9 C 941 HZ * 0 # D
MAIN BLOCKS OF INDUSTRIAL AUTOMATION
MICRO-CONTROLLER
GSM MODEM
RELAY CIRCUITS
BLOCK DIAGRAM
Power Supply
(5V)
Micro Controller
GSM
Modem
HT9170B
RELAY
DriverCKT
Relay1
Relay2
Relay3
L C D
Device
Device
Device
MICROCONTROLLER
Microcontroller is a small computer.
Microcontroller consists of on-chip RAM, ROM, I/O Ports etc.
Microcontroller controls the electronic devices using the program that is provided to the controller.
A Single Chip
microcontroller
BLOCK DIAGRAM OF MICRO-CONTROLLER
PIN DIAGRAM OF MICRO-CONTROLLER
GSM MODEM
GSM (Global System for Mobile
communications) continues to assert
itself as the world's leading cellular
communications technology.
The GSM Modems can be used for
setting up a kind of M2M
communication either using CALL or
SMS services. This can be
effectively used for the automation of
various homes, offices and
industries.
RELAY CIRCUITS
• A relay circuit is designed to control
operation of electrical equipment.
• Relays are used where it is
necessary to control a circuit by a
low-power signal (with complete
electrical isolation between control
and controlled circuits), or where
several circuits must be controlled
by one signal.
WORKING ?
MICRO-CONTROLLER
GSM MODEM
MOBILE
RELAY 1 RELAY 2 RELAY 3
DEVICE 1 DEVICE 2 DEVICE 3
APPLICATIONS
Applications in industrial
Electronic appliances
Household Applications
Machines etc.
Can also be used for security purpose
after modification
ADVANTAGES
Wireless technology.
It is cheaper
It uses low power
Acknowledgement to the user to know the
work is done or not.
CONCLUSION
The SMS from the master unit was
successfully processed by mobile unit and
sent to micro-controller through interfaces
and successfully controlled the electronic
devices connected to micro controller.
FUTURE SCOPE
To ensure proper maintenance of machines:
By using some extra devices we can
check the status of machines whether they are
working or not and also the part which is not
working properly(sensors) .
• Enter the password.
• When the password has been incorrectly entered four times in a row, the interface an error sound is produced and the receiver replaced on-hook this function finds any attempt by 'hackers' to quickly try a large number of codes in a sequence.
• If password is correct enter in to the main menu .• Main menu : Enter Command * < 1 – 8 > * - operate one of the four relays 1 to 8. # < 1 – 8 > # - release one of the four relays 1 to 8. 123 – Read EPROM 456 – Change password 789 – Read relay status * 0 # - Line disconnected
THANKS!!
Special thanks to all of you for your Patience