Il corpo
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Il corpo
Le braccia e la gamba
22in.
11in. 11in.
18in.
18in.
Flip this board over to create the lowerpart of the leg.
This cut is ata 45° angle.
Mark and cut this board to 18 inchesfrom the top of the knee.
approx. 12in.
11in.
approx. 12in.
Flip this board over, measure and cut to 18 inches.
Use the remaining scrap for the top part of the leg.
Place these pices on the leg,measure and mark them at11 inches from the knee.
Make the cut using a 15° angle.
Flip this board over, measure and cut to approx. 12 inches.
This cut is ata 45° angle.
This cut is ata 45° angle.
18in.
18in.
scrap
Scrap board will be approximately 54 inches long if you started with an 8 foot board.
This cut is a15° angle.
1.
2.
3.
4.
Assemble leg using wood glue and screws.
Come fare i buchi per le braccia
e le gambe e come incastrare il
tutto
28"
14"
21"center
Straight Center Line
7"
Transfering your measurements to your dummy is a little tricky. Mostly because it's hard to find a log that is exactly 9 inches in diameter.
First: make a center line. I did this by laying a long straight edge along the body while it was on my saw horses.
Second: Find the center point. Measure the circumference of your body. I was lucky and it came out to be 28". Divide your measurement by 4 to comeup with quater marks. For example: 28 divided by 4 is 7. so I made a mark every 7 inches around the body. I then connected the dots. Where the lines intersect is the center point.
center
Distance to outsideof body.
Lengthof arms11.75"on my dummy
Transfer the locationof the centerline
marks to thebody of your
dummy.
Adjust arms of protractor tothe desired arm width
8.5" on my dummy
Third: Find the angles of your arms. Make a protractor out scrap 1x2s. Draw a center line down the center of each arm of the protractor. Attache the protractor to your dummy body at the center point.When i made my protractor I just used a long enough screw to go through the protractor and into the dummy center point.
Mark how long your dummy arms will beand adjust the distance between thearms until they are the desired distanceapart.
Transfer the the location of the centerline marks to your dummy body.These marks should be equaldistance away from the centerline.
center
These are the marks transfered fromyour protractor.
You now have the correct angle to
drill you arms holes.
These marks should be equaldistance from the center line.
Center Line for Arm hole.
Center Line for Arm hole.
Extend the marks down the length of the wooden dummy body. When youtransfer the markks for your arm holes make sure that you center the top arm holes on these lines. After you get all your makrs in place, double checkjust to make sure and then you can start drilling and chiseling.
A
BB
C
DA
B
B
A
C
D
Building the leg with an overlaping joint:
You will need 1 8' 2x3 and 1 8' 1x3.
The knee angle of the leg is 45° and the leg is inserted into the dummy at a 15° angle. So, only the two smaller 1x3s actually have a 15° angle cut on one side. All other cuts are at a 45° angle.
Get the measurements from theplans on this page:http://www.wckfc.com/news/dummy/
A. 1x3B. 1x3C. 2x3D. 2x3
D
C
A
Step 1. I used wood glue and screws to attachall the pieces.
Step 2.
Step 3.
Finished leg.
Related Documents
