-
2010 ASME Boiler and Pressure Vessel CodeA N I N T E R N A T I O
N A L C O D E
II Part CSpecifications for Welding Rods, Electrodes, and Filler
Metals
Materials
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
-
INTENTIONALLY LEFT BLANK
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
标准分享网 www.bzfxw.com 免费下载
-
A N I N T E R N A T I O N A L C O D E
2010 ASME Boiler &Pressure Vessel Code2010 Edition July 1,
2010
IIPart CSpecifications for WeldingRods, Electrodes, and
FillerMetals
MATERIALSASME Boiler and Pressure Vessel Committee on
Materials
Three Park Avenue • New York, NY • 10016 USA
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
-
www.bzfxw.com
Date of Issuance: July 1, 2010(Includes all Addenda dated July
2009 and earlier)
This international code or standard was developed under
procedures accredited as meeting the criteria for American
NationalStandards and it is an American National Standard. The
Standards Committee that approved the code or standard was
balancedto assure that individuals from competent and concerned
interests have had an opportunity to participate. The proposed
codeor standard was made available for public review and comment
that provides an opportunity for additional public input
fromindustry, academia, regulatory agencies, and the
public-at-large.
ASME does not “approve,” “rate,” or “endorse” any item,
construction, proprietary device, or activity.ASME does not take
any position with respect to the validity of any patent rights
asserted in connection with any items
mentioned in this document, and does not undertake to insure
anyone utilizing a standard against liability for infringement
ofany applicable letters patent, nor assume any such liability.
Users of a code or standard are expressly advised that
determinationof the validity of any such patent rights, and the
risk of infringement of such rights, is entirely their own
responsibility.
Participation by federal agency representative(s) or person(s)
affiliated with industry is not to be interpreted as governmentor
industry endorsement of this code or standard.
ASME accepts responsibility for only those interpretations of
this document issued in accordance with the established
ASMEprocedures and policies, which precludes the issuance of
interpretations by individuals.
The footnotes in this document are part of this American
National Standard.
ASME collective membership mark
The above ASME symbols are registered in the U.S. Patent
Office.
“ASME” is the trademark of the American Society of Mechanical
Engineers.
The Specifications published and copyrighted by the American
Welding Societyare reproduced with the Society’s permission.
No part of this document may be reproduced in any form, in an
electronic retrieval system orotherwise, without the prior written
permission of the publisher.
Library of Congress Catalog Card Number: 56-3934Printed in the
United States of America
Adopted by the Council of the American Society of Mechanical
Engineers, 1914.Revised 1940, 1941, 1943, 1946, 1949, 1952, 1953,
1956, 1959, 1962, 1965, 1968, 1971, 1974, 1977, 1980, 1983,
1986,
1989, 1992, 1995, 1998, 2001, 2004, 2007, 2010
The American Society of Mechanical EngineersThree Park Avenue,
New York, NY 10016-5990
Copyright © 2010 byTHE AMERICAN SOCIETY OF MECHANICAL
ENGINEERS
All Rights Reserved
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
标准分享网 www.bzfxw.com 免费下载
-
www.bzfxw.com
2010 ASMEBOILER AND PRESSURE VESSEL CODE
SECTIONS
I Rules for Construction of Power Boilers
II MaterialsPart A — Ferrous Material SpecificationsPart B —
Nonferrous Material SpecificationsPart C — Specifications for
Welding Rods, Electrodes, and Filler MetalsPart D — Properties
(Customary)Part D — Properties (Metric)
III Rules for Construction of Nuclear Facility
ComponentsSubsection NCA — General Requirements for Division 1 and
Division 2Division 1Subsection NB — Class 1 ComponentsSubsection NC
— Class 2 ComponentsSubsection ND — Class 3 ComponentsSubsection NE
— Class MC ComponentsSubsection NF — SupportsSubsection NG — Core
Support StructuresSubsection NH — Class 1 Components in Elevated
Temperature ServiceAppendices
Division 2 — Code for Concrete Containments
Division 3 — Containments for Transportation and Storage of
Spent Nuclear Fueland High Level Radioactive Material and Waste
IV Rules for Construction of Heating Boilers
V Nondestructive Examination
VI Recommended Rules for the Care and Operation of Heating
Boilers
VII Recommended Guidelines for the Care of Power Boilers
VIII Rules for Construction of Pressure VesselsDivision
1Division 2 — Alternative RulesDivision 3 — Alternative Rules for
Construction of High Pressure Vessels
IX Welding and Brazing Qualifications
X Fiber-Reinforced Plastic Pressure Vessels
XI Rules for Inservice Inspection of Nuclear Power Plant
Components
XII Rules for Construction and Continued Service of Transport
Tanks
iii
(10)
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
-
www.bzfxw.com
ADDENDA
Addenda, which include additions and revisions to indi-vidual
Sections of the Code, will be sent automatically topurchasers of
the applicable Sections up to the publicationof the 2013 Code. The
2010 Code is available only in theloose-leaf format; accordingly,
the Addenda will be issuedin the loose-leaf, replacement-page
format.
INTERPRETATIONS
ASME issues written replies to inquiries
concerninginterpretation of technical aspects of the Code. The
Inter-pretations for each individual Section will be
publishedseparately and will be included as part of the update
serviceto that Section. Interpretations of Section III, Divisions
1
iv
and 2, will be included with the update service to Subsec-tion
NCA.
Interpretations of the Code are posted in January andJuly at
www.cstools.asme.org/interpretations.
CODE CASES
The Boiler and Pressure Vessel Committee meets regu-larly to
consider proposed additions and revisions to theCode and to
formulate Cases to clarify the intent of existingrequirements or
provide, when the need is urgent, rulesfor materials or
constructions not covered by existing Coderules. Those Cases that
have been adopted will appearin the appropriate 2010 Code Cases
book: “Boilers andPressure Vessels” and “Nuclear Components.”
Supple-ments will be sent automatically to the purchasers of
theCode Cases books up to the publication of the 2013 Code.
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
标准分享网 www.bzfxw.com 免费下载
-
www.bzfxw.com
CONTENTS
List of Sections . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . iiiForeword . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
viiStatements of Policy . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . ixPersonnel . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . xAWS
Personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . xxiiSubmittal of Technical Inquiries . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . xxvGuideline on Approval of
New Material . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . xxviiPreface . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . xxixSummary of Changes . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . xxxList of Changes in
BC Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xxxi
SpecificationsSFA-5.01 Filler Metal Procurement Guidelines . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1SFA-5.02/SFA-5.02M Filler Metal Standard Sizes, Packaging, and
Physical Attributes . . . . . . . . . 11SFA-5.1/SFA-5.1M Carbon
Steel Electrodes for Shielded Metal Arc Welding. . . . . . . . . .
. . . . . 21SFA-5.2/SFA-5.2M Carbon and Low-Alloy Steel Rods for
Oxyfuel Gas Welding . . . . . . . . . . . 61SFA-5.3/SFA-5.3M
Aluminum and Aluminum-Alloy Electrodes for Shielded Metal Arc
Welding. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
71SFA-5.4/SFA-5.4M Stainless Steel Electrodes for Shielded Metal
Arc Welding . . . . . . . . . . . . . 85SFA-5.5/SFA-5.5M Low-Alloy
Steel Electrodes for Shielded Metal Arc Welding . . . . . . . . . .
. 117SFA-5.6/SFA-5.6M Copper and Copper-Alloy Electrodes for
Shielded Metal Arc
Welding. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
167SFA-5.7/SFA-5.7M Copper and Copper-Alloy Bare Welding Rods and
Electrodes . . . . . . . . . . 187SFA-5.8/SFA-5.8M Filler Metals
for Brazing and Braze Welding. . . . . . . . . . . . . . . . . . .
. . . . . . . 199SFA-5.9/SFA-5.9M Bare Stainless Steel Welding
Electrodes and Rods . . . . . . . . . . . . . . . . . . . . .
227SFA-5.10/SFA-5.10M Bare Aluminum and Aluminum-Alloy Welding
Electrodes and Rods . . . . 251SFA-5.11/SFA-5.11M Nickel and
Nickel-Alloy Welding Electrodes for Shielded Metal Arc
Welding. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
277SFA-5.12/SFA-5.12M Tungsten and Oxide Dispersed Tungsten
Electrodes for Arc Welding
and Cutting . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 307SFA-5.13
Surfacing Electrodes for Shielded Metal Arc Welding. . . . . . . .
. . . . . . . . . . 319SFA-5.14/SFA-5.14M Nickel and Nickel-Alloy
Bare Welding Electrodes and Rods. . . . . . . . . . . . 339SFA-5.15
Welding Electrodes and Rods for Cast Iron . . . . . . . . . . . . .
. . . . . . . . . . . . . . 359SFA-5.16/SFA-5.16M Titanium and
Titanium-Alloy Welding Electrodes and Rods . . . . . . . . . . . .
377SFA-5.17/SFA-5.17M Carbon Steel Electrodes and Fluxes for
Submerged Arc Welding. . . . . . . . 393SFA-5.18/SFA-5.18M Carbon
Steel Electrodes and Rods for Gas Shielded Arc Welding . . . . . .
. 419SFA-5.20/SFA-5.20M Carbon Steel Electrodes for Flux Cored Arc
Welding . . . . . . . . . . . . . . . . . . 443SFA-5.21 Bare
Electrodes and Rods for Surfacing . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 477SFA-5.22 Stainless Steel Electrodes
for Flux Cored Arc Welding and Stainless
Steel Flux Cored Rods for Gas Tungsten Arc Welding. . . . . . .
. . . . . . . . 501SFA-5.23/SFA-5.23M Low-Alloy Steel Electrodes
and Fluxes for Submerged Arc Welding . . . . 537SFA-5.24/SFA-5.24M
Zirconium and Zirconium-Alloy Welding Electrodes and Rods. . . . .
. . . . . 573SFA-5.25/SFA-5.25M Carbon and Low-Alloy Steel
Electrodes and Fluxes for Electroslag
Welding. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
583SFA-5.26/SFA-5.26M Carbon and Low-Alloy Steel Electrodes for
Electrogas Welding . . . . . . . . 607SFA-5.28/SFA-5.28M Low-Alloy
Steel Electrodes and Rods for Gas Shielded Arc Welding. . . .
631
v
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
-
www.bzfxw.com
SFA-5.29/SFA-5.29M Low-Alloy Steel Electrodes for Flux Cored Arc
Welding. . . . . . . . . . . . . . . 661SFA-5.30/SFA-5.30M
Consumable Inserts . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . 699SFA-5.31
Fluxes for Brazing and Braze Welding . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . 717SFA-5.32/SFA-5.32M Welding
Shielding Gases. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . 727SFA-5.34/SFA-5.34M
Nickel-Alloy Electrodes for Flux Cored Arc Welding . . . . . . . .
. . . . . . . . . . 741
MANDATORYAPPENDIX
I Standard Units for Use in Equations. . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . 765
vi
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
标准分享网 www.bzfxw.com 免费下载
-
www.bzfxw.com
FOREWORD
The American Society of Mechanical Engineers set up acommittee
in 1911 for the purpose of formulating standardrules for the
construction of steam boilers and other pres-sure vessels. This
committee is now called the Boiler andPressure Vessel
Committee.
The Committee’s function is to establish rules of
safety,relating only to pressure integrity, governing the
construc-tion1 of boilers, pressure vessels, transport tanks
andnuclear components, and inservice inspection for
pressureintegrity of nuclear components and transport tanks, andto
interpret these rules when questions arise regarding theirintent.
This code does not address other safety issues relat-ing to the
construction of boilers, pressure vessels, transporttanks and
nuclear components, and the inservice inspectionof nuclear
components and transport tanks. The user ofthe Code should refer to
other pertinent codes, standards,laws, regulations, or other
relevant documents. With fewexceptions, the rules do not, of
practical necessity, reflectthe likelihood and consequences of
deterioration in servicerelated to specific service fluids or
external operating envi-ronments. Recognizing this, the Committee
has approveda wide variety of construction rules in this Section to
allowthe user or his designee to select those which will providea
pressure vessel having a margin for deterioration in ser-vice so as
to give a reasonably long, safe period of use-fulness. Accordingly,
it is not intended that this Sectionbe used as a design handbook;
rather, engineering judgmentmust be employed in the selection of
those sets of Coderules suitable to any specific service or
need.
This Code contains mandatory requirements, specificprohibitions,
and nonmandatory guidance for constructionactivities. The Code does
not address all aspects of theseactivities and those aspects which
are not specificallyaddressed should not be considered prohibited.
The Codeis not a handbook and cannot replace education,
experi-ence, and the use of engineering judgment. The
phraseengineering judgment refers to technical judgments madeby
knowledgeable designers experienced in the applicationof the Code.
Engineering judgments must be consistentwith Code philosophy and
such judgments must neverbe used to overrule mandatory requirements
or specificprohibitions of the Code.
1 Construction, as used in this Foreword, is an all-inclusive
term com-prising materials, design, fabrication, examination,
inspection, testing,certification, and pressure relief.
vii
The Committee recognizes that tools and techniquesused for
design and analysis change as technology prog-resses and expects
engineers to use good judgment in theapplication of these tools.
The designer is responsible forcomplying with Code rules and
demonstrating compliancewith Code equations when such equations are
mandatory.The Code neither requires nor prohibits the use of
comput-ers for the design or analysis of components constructedto
the requirements of the Code. However, designers andengineers using
computer programs for design or analysisare cautioned that they are
responsible for all technicalassumptions inherent in the programs
they use and theyare responsible for the application of these
programs totheir design.
The Code does not fully address tolerances. Whendimensions,
sizes, or other parameters are not specifiedwith tolerances, the
values of these parameters are consid-ered nominal and allowable
tolerances or local variancesmay be considered acceptable when
based on engineeringjudgment and standard practices as determined
by thedesigner.
The Boiler and Pressure Vessel Committee deals withthe care and
inspection of boilers and pressure vessels inservice only to the
extent of providing suggested rules ofgood practice as an aid to
owners and their inspectors.
The rules established by the Committee are not to beinterpreted
as approving, recommending, or endorsing anyproprietary or specific
design or as limiting in any way themanufacturer’s freedom to
choose any method of designor any form of construction that
conforms to the Code rules.
The Boiler and Pressure Vessel Committee meets regu-larly to
consider revisions of the rules, new rules as dictatedby
technological development, Code Cases, and requestsfor
interpretations. Only the Boiler and Pressure VesselCommittee has
the authority to provide official interpreta-tions of this Code.
Requests for revisions, new rules, CodeCases, or interpretations
shall be addressed to the Secretaryin writing and shall give full
particulars in order to receiveconsideration and action (see
Mandatory Appendix cov-ering preparation of technical inquiries).
Proposed revi-sions to the Code resulting from inquiries will be
presentedto the Main Committee for appropriate action. The actionof
the Main Committee becomes effective only after con-firmation by
letter ballot of the Committee and approvalby ASME.
(10)
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
-
www.bzfxw.com
Proposed revisions to the Code approved by the Commit-tee are
submitted to the American National Standards Insti-tute and
published at
http://cstools.asme.org/csconnect/public/index.cfm?PublicReviewpRevisions
to invite com-ments from all interested persons. After the allotted
timefor public review and final approval by ASME, revisionsare
published in updates to the Code.
Code Cases may be used in the construction of compo-nents to be
stamped with the ASME Code symbol begin-ning with the date of their
approval by ASME.
After Code revisions are approved by ASME, they maybe used
beginning with the date of issuance. Revisions,except for revisions
to material specifications in SectionII, Parts A and B, become
mandatory six months after suchdate of issuance, except for boilers
or pressure vesselscontracted for prior to the end of the six-month
period.Revisions to material specifications are originated by
theAmerican Society for Testing and Materials (ASTM) andother
recognized national or international organizations,and are usually
adopted by ASME. However, those revi-sions may or may not have any
effect on the suitability ofmaterial, produced to earlier editions
of specifications, foruse in ASME construction. ASME material
specificationsapproved for use in each construction Code are listed
inthe Guidelines for Acceptable ASTM Editions and in theGuidelines
for Acceptable Non-ASTM Editions, in SectionII, Parts A and B.
These Guidelines list, for each specifica-tion, the latest edition
adopted by ASME, and earlier andlater editions considered by ASME
to be identical forASME construction.
The Boiler and Pressure Vessel Committee in the formu-lation of
its rules and in the establishment of maximumdesign and operating
pressures considers materials, con-struction, methods of
fabrication, inspection, and safetydevices.
The Code Committee does not rule on whether a compo-nent shall
or shall not be constructed to the provisions ofthe Code. The Scope
of each Section has been establishedto identify the components and
parameters considered bythe Committee in formulating the Code
rules.
Questions or issues regarding compliance of a specificcomponent
with the Code rules are to be directed to theASME Certificate
Holder (Manufacturer). Inquiries con-cerning the interpretation of
the Code are to be directed
viii
to the ASME Boiler and Pressure Vessel Committee.ASME is to be
notified should questions arise concerningimproper use of an ASME
Code symbol.
The specifications for materials given in Section II
areidentical with or similar to those of specifications publishedby
ASTM, AWS, and other recognized national or interna-tional
organizations. When reference is made in an ASMEmaterial
specification to a non-ASME specification forwhich a companion ASME
specification exists, the refer-ence shall be interpreted as
applying to the ASME materialspecification. Not all materials
included in the materialspecifications in Section II have been
adopted for Codeuse. Usage is limited to those materials and grades
adoptedby at least one of the other Sections of the Code for
applica-tion under rules of that Section. All materials allowed
bythese various Sections and used for construction within thescope
of their rules shall be furnished in accordance withmaterial
specifications contained in Section II or referencedin the
Guidelines for Acceptable Editions in Section II,Parts A and B,
except where otherwise provided in CodeCases or in the applicable
Section of the Code. Materialscovered by these specifications are
acceptable for use initems covered by the Code Sections only to the
degreeindicated in the applicable Section. Materials for Code
useshould preferably be ordered, produced, and documentedon this
basis; Guidelines for Acceptable Editions inSection II, Part A and
Guidelines for Acceptable Editionsin Section II, Part B list
editions of ASME and year datesof specifications that meet ASME
requirements and whichmay be used in Code construction. Material
produced toan acceptable specification with requirements
differentfrom the requirements of the corresponding
specificationslisted in the Guidelines for Acceptable Editions in
Part Aor Part B may also be used in accordance with the
above,provided the material manufacturer or vessel
manufacturercertifies with evidence acceptable to the Authorized
Inspec-tor that the corresponding requirements of
specificationslisted in the Guidelines for Acceptable Editions in
Part Aor Part B have been met. Material produced to an
acceptablematerial specification is not limited as to country of
origin.
When required by context in this Section, the singularshall be
interpreted as the plural, and vice-versa; and thefeminine,
masculine, or neuter gender shall be treated assuch other gender as
appropriate.
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---标准分享网
www.bzfxw.com 免费下载
-
STATEMENT OF POLICY (10)
ON THE USE OF CODE SYMBOLS AND
CODE AUTHORIZATION IN ADVERTISING
ASME has established procedures to authorize
qualifiedorganizations to perform various activities in
accordancewith the requirements of the ASME Boiler and
PressureVessel Code. It is the aim of the Society to provide
recogni-tion of organizations so authorized. An organization
hold-ing authorization to perform various activities inaccordance
with the requirements of the Code may statethis capability in its
advertising literature.
Organizations that are authorized to use Code Symbolsfor marking
items or constructions that have been con-structed and inspected in
compliance with the ASME Boilerand Pressure Vessel Code are issued
Certificates of Autho-rization. It is the aim of the Society to
maintain the standingof the Code Symbols for the benefit of the
users, theenforcement jurisdictions, and the holders of the
symbolswho comply with all requirements.
Based on these objectives, the following policy has
beenestablished on the usage in advertising of facsimiles of
thesymbols, Certificates of Authorization, and reference toCode
construction. The American Society of Mechanical
STATEMENT OF POLICY
ON THE USE OF ASME MARKING
TO IDENTIFY MANUFACTURED ITEMS
The ASME Boiler and Pressure Vessel Code providesrules for the
construction of boilers, pressure vessels, andnuclear components.
This includes requirements for mate-rials, design, fabrication,
examination, inspection, andstamping. Items constructed in
accordance with all of theapplicable rules of the Code are
identified with the officialCode Symbol Stamp described in the
governing Sectionof the Code.
Markings such as “ASME,” “ASME Standard,” or anyother marking
including “ASME” or the various Code
ix
Engineers does not “approve,” “certify,” “rate,” or“endorse” any
item, construction, or activity and there shallbe no statements or
implications that might so indicate. Anorganization holding a Code
Symbol and/or a Certificate ofAuthorization may state in
advertising literature that items,constructions, or activities “are
built (produced or per-formed) or activities conducted in
accordance with therequirements of the ASME Boiler and Pressure
VesselCode,” or “meet the requirements of the ASME Boiler
andPressure Vessel Code.” An ASME corporate logo shall notbe used
by any organization other than ASME.
The ASME Symbol shall be used only for stamping andnameplates as
specifically provided in the Code. However,facsimiles may be used
for the purpose of fostering theuse of such construction. Such
usage may be by an associa-tion or a society, or by a holder of a
Code Symbol whomay also use the facsimile in advertising to show
thatclearly specified items will carry the symbol. General usageis
permitted only when all of a manufacturer’s items areconstructed
under the rules.
Symbols shall not be used on any item that is not con-structed
in accordance with all of the applicable require-ments of the
Code.
Items shall not be described on ASME Data ReportForms nor on
similar forms referring to ASME that tendto imply that all Code
requirements have been met when,in fact, they have not been. Data
Report Forms coveringitems not fully complying with ASME
requirements shouldnot refer to ASME or they should clearly
identify all excep-tions to the ASME requirements.
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
-
PERSONNELASME Boiler and Pressure Vessel Standards
Committees,
Subgroups, and Working GroupsAs of January 1, 2010
TECHNICAL OVERSIGHT MANAGEMENT COMMITTEE (TOMC)
J. G. Feldstein, Chair J. F. HenryT. P. Pastor, Vice Chair C. L.
HoffmannJ. S. Brzuszkiewicz, Staff G. G. Karcher
Secretary W. M. LundyR. W. Barnes J. R. MacKayR. J. Basile U. R.
MillerJ. E. Batey P. A. MolvieD. L. Berger W. E. NorrisM. N.
Bressler G. C. ParkD. A. Canonico M. D. RanaR. P. Deubler B. W.
RobertsD. A. Douin S. C. RobertsD. Eisberg F. J. Schaaf, Jr.R. E.
Gimple A. SelzM. Gold R. W. SwayneT. E. Hansen
HONORARY MEMBERS (MAIN COMMITTEE)
F. P. Barton M. H. JawadR. J. Cepluch A. J. JustinL. J. Chockie
W. G. KnechtT. M. Cullen J. LeCoffW. D. Doty T. G. McCartyJ. R.
Farr G. C. MillmanG. E. Feigel R. A. MoenR. C. Griffin R. F.
ReedyO. F. Hedden K. K. TamE. J. Hemzy L. P. Zick, Jr.
ADMINISTRATIVE COMMITTEE
J. S. Brzuszkiewicz, Staff J. G. FeldsteinSecretary J. F.
Henry
R. W. Barnes P. A. MolvieJ. E. Batey G. C. ParkD. L. Berger T.
P. PastorD. Eisberg A. Selz
HONORS AND AWARDS COMMITTEE
M. Gold, Chair W. L. Haag, Jr.F. E. Gregor, Vice Chair S. F.
Harrison, Jr.T. Schellens, Staff Secretary R. M. JesseeD. R. Sharp,
Staff Secretary W. C. LaRochelleR. J. Basile T. P. PastorJ. E.
Batey A. SelzD. L. Berger R. R. StevensonJ. G. Feldstein
x
MARINE CONFERENCE GROUP
H. N. Patel, Chair G. PallichadathJ. G. Hungerbuhler, Jr. J. D.
Reynolds
CONFERENCE COMMITTEE
R. J. Aben, Jr. — Michigan M. R. Klosterman — Iowa(Chair) M.
Kotb — Quebec, Canada
R. D. Reetz — North Dakota K. J. Kraft — Maryland(Vice Chair) B.
Krasiun — Saskatchewan,
D. A. Douin — Ohio Canada(Secretary) K. T. Lau — Alberta,
Canada
J. S. Aclaro — California G. Lemay — Ontario, CanadaJ. T. Amato
— Minnesota W. McGivney — New YorkB. P. Anthony — Rhode Island T.
J. Monroe — OklahomaR. D. Austin — Arizona G. R. Myrick —
ArkansasE. W. Bachellier — Nunavut, S. V. Nelson — Colorado
Canada W. R. Owens — LouisianaB. F. Bailey — Illinois R. P. Pate
— AlabamaJ. E. Bell — Michigan R. L. Perry — NevadaW. K. Brigham —
New H. D. Pfaff — South Dakota
Hampshire A. E. Platt — ConnecticutM. A. Burns — Florida J. F.
Porcella — West VirginiaJ. H. Burpee — Maine M. R. Poulin — IdahoC.
B. Cantrell — Nebraska D. C. Price — YukonD. C. Cook — California
Territory, CanadaJ. A. Davenport — R. S. Pucek — Wisconsin
Pennsylvania T. W. Rieger — Manitoba,S. Donovan — Northwest
Canada
Territories, Canada A. E. Rogers — TennesseeD. Eastman —
Newfoundland D. E. Ross — New Brunswick,
and Labrador, Canada CanadaE. Everett — Georgia K. A. Rudolph —
HawaiiC. Fulton — Alaska M. J. Ryan — IllinoisJ. M. Given, Jr. —
North G. Scribner — Missouri
Carolina J. G. Siggers — BritishM. Graham — Oregon Columbia,
CanadaR. J. Handy — Kentucky T. Stewart — MontanaJ. B. Harlan —
Delaware R. K. Sturm — UtahE. G. Hilton — Virginia M. J. Verhagen —
WisconsinK. Hynes — Prince Edward P. L. Vescio, Jr. — New York
Island, Canada M. Washington — New JerseyD. T. Jagger — Ohio K.
L. Watson — MississippiD. J. Jenkins — Kansas L. Williamson —
WashingtonA. P. Jones — Texas D. J. Willis — IndianaE. S. Kawa, Jr.
—
Massachusetts
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
标准分享网 www.bzfxw.com 免费下载
-
INTERNATIONAL INTEREST REVIEW GROUP
V. Felix C. MinuY.-G. Kim Y.-W. ParkS. H. Leong R. ReynagaW. Lin
P. WilliamsonO. F. Manafa
PROJECT TEAM ON HYDROGEN TANKS
M. D. Rana, Chair C. T. I. WebsterA. P. Amato, Staff Secretary
R. C. Biel, ContributingF. L. Brown MemberD. A. Canonico J.
Birdsall, ContributingD. C. Cook MemberJ. Coursen M. Duncan,
ContributingJ. W. Felbaum MemberB. D. Hawkes D. R. Frikken,
ContributingN. L. Newhouse MemberA. S. Olivares L. E. Hayden, Jr.,
ContributingG. B. Rawls, Jr. MemberB. F. Shelley K. T. Lau,
ContributingJ. R. Sims, Jr. MemberN. Sirosh K. Oyamada,
ContributingJ. H. Smith MemberS. Staniszewski C. H. Rivkin,
ContributingR. Subramanian MemberT. Tahara C. San Marchi,
ContributingD. W. Treadwell MemberE. Upitis B. Somerday,
ContributingY. Wada Member
COMMITTEE ON POWER BOILERS (I)
D. L. Berger, Chair T. C. McGoughR. E. McLaughlin, Vice Chair P.
A. MolvieU. D’Urso, Staff Secretary Y. OishiJ. L. Arnold J. T.
PillowS. W. Cameron B. W. RobertsD. A. Canonico R. D. Schueler,
Jr.K. K. Coleman J. P. Swezy, Jr.P. D. Edwards J. M. TanzoshP.
Fallouey R. V. WielgoszinskiJ. G. Feldstein D. J. WillisG. W.
Galanes G. Ardizzoia, DelegateT. E. Hansen H. Michael, DelegateJ.
F. Henry E. M. Ortman, AlternateJ. S. Hunter D. N. French,
HonoraryW. L. Lowry MemberJ. R. MacKay R. L. Williams, HonoraryF.
Massi Member
Subgroup on Design (BPV I)
P. A. Molvie, Chair B. W. MooreJ. Vattappilly, Secretary R. D.
Schueler, Jr.D. I. Anderson J. L. SeigleP. Dhorajia J. P. Swezy,
Jr.J. P. Glaspie S. V. TorkildsonG. B. Komora G. Ardizzoia,
DelegateJ. C. Light
xi
Subgroup on Fabrication and Examination (BPV I)J. T. Pillow,
Chair C. T. McDarisG. W. Galanes, Secretary T. C. McGoughJ. L.
Arnold R. E. McLaughlinD. L. Berger Y. OishiS. W. Cameron J. P.
Swezy, Jr.J. Hainsworth R. V. WielgoszinskiT. E. Hansen
Subgroup on General Requirements (BPV I)R. E. McLaughlin, Chair
J. T. PillowF. Massi, Secretary D. TompkinsP. D. Edwards S. V.
TorkildsonT. E. Hansen D. E. TuttleW. L. Lowry R. V.
WielgoszinskiT. C. McGough D. J. WillisE. M. Ortman
Subgroup on Materials (BPV I)B. W. Roberts, Chair K. L. HayesJ.
S. Hunter, Secretary J. F. HenryS. H. Bowes O. X. LiD. A. Canonico
J. R. MacKayK. K. Coleman F. MasuyamaP. Fallouey D. W. RahoiG. W.
Galanes J. M. Tanzosh
Subgroup on Piping (BPV I)T. E. Hansen, Chair W. L. LowryD. L.
Berger F. MassiP. D. Edwards T. C. McGoughG. W. Galanes D.
TompkinsT. G. Kosmatka E. A. Whittle
Subgroup on Heat Recovery Steam Generators (BPV I)T. E. Hansen,
Chair E. M. OrtmanD. Dziubinski, Secretary R. D. Schueler, Jr.L. R.
Douglas J. C. Steverman, Jr.J. Gertz D. TompkinsG. B. Komora S. V.
TorkildsonC. T. McDaris B. C. TurczynskiB. W. Moore
COMMITTEE ON MATERIALS (II)J. F. Henry, Chair R. C. SutherlinM.
Gold, Vice Chair R. W. SwindemanN. Lobo, Staff Secretary J. M.
TanzoshF. Abe B. E. ThurgoodA. Appleton D. Kwon, DelegateM. N.
Bressler O. Oldani, DelegateH. D. Bushfield W. R. Apblett, Jr.,
ContributingJ. Cameron MemberD. A. Canonico E. G. Nisbett,
ContributingA. Chaudouet MemberP. Fallouey E. Upitis,
ContributingJ. R. Foulds MemberD. W. Gandy T. M. Cullen, HonoraryM.
H. Gilkey MemberJ. F. Grubb W. D. Doty, HonoraryC. L. Hoffmann
MemberM. Katcher W. D. Edsall, HonoraryP. A. Larkin MemberF.
Masuyama G. C. Hsu, Honorary MemberR. K. Nanstad R. A. Moen,
HonoraryM. L. Nayyar MemberD. W. Rahoi C. E. Spaeder, Jr.,
HonoraryB. W. Roberts MemberE. Shapiro A. W. Zeuthen, HonoraryM. H.
Skillingberg Member
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
-
Subgroup on External Pressure (BPV II)
R. W. Mikitka, Chair M. KatcherJ. A. A. Morrow, Secretary D. L.
KurleL. F. Campbell C. R. ThomasD. S. Griffin C. H. Sturgeon,
ContributingJ. F. Grubb MemberJ. R. Harris III
Subgroup on Ferrous Specifications (BPV II)
A. Appleton, Chair L. J. LavezziR. M. Davison W. C. MackB. M.
Dingman J. K. MahaneyM. J. Dosdourian R. J. MarciniecP. Fallouey A.
S. MelilliT. Graham E. G. NisbettJ. F. Grubb K. E. OrieK. M. Hottle
J. ShickD. S. Janikowski E. UpitisD. C. Krouse R. Zawierucha
Subgroup on International Material Specifications (BPV II)
A. Chaudouet, Chair W. M. LundyD. Dziubinski, Secretary A. R.
NyweningS. W. Cameron R. D. Schueler, Jr.D. A. Canonico E. UpitisP.
Fallouey D. Kwon, DelegateA. F. Garbolevsky O. Oldani, DelegateD.
O. Henry H. Lorenz, ContributingM. Ishikawa MemberO. X. Li
Subgroup on Strength, Ferrous Alloys (BPV II)
C. L. Hoffmann, Chair F. MasuyamaJ. M. Tanzosh, Secretary S.
MatsumotoF. Abe H. MurakamiW. R. Apblett, Jr. D. W. RahoiD. A.
Canonico B. W. RobertsA. Di Rienzo M. S. SheltonP. Fallouey J. P.
ShingledeckerJ. R. Foulds M. J. SlaterM. Gold R. W. SwindemanJ. A.
Hall B. E. ThurgoodJ. F. Henry T. P. Vassallo, Jr.K. Kimura
Subgroup on Nonferrous Alloys (BPV II)
M. Katcher, Chair H. MatsuoR. C. Sutherlin, Secretary J. A.
McMasterW. R. Apblett, Jr. D. W. RahoiM. H. Gilkey E. ShapiroJ. F.
Grubb M. H. SkillingbergA. Heino D. TylerJ. Kissell R. ZawieruchaP.
A. Larkin H. D. Bushfield, ContributingT. M. Malota MemberS.
Matsumoto
Subgroup on Physical Properties (BPV II)
J. F. Grubb, Chair P. FalloueyH. D. Bushfield E. Shapiro
xii
Subgroup on Strength of Weldments (BPV II & BPV IX)
J. M. Tanzosh, Chair K. L. HayesW. F. Newell, Jr., Secretary J.
F. HenryS. H. Bowes D. W. RahoiK. K. Coleman B. W. RobertsP. D.
Flenner J. P. ShingledeckerJ. R. Foulds W. J. SperkoD. W. Gandy B.
E. Thurgood
Special Working Group on Nonmetallic Materials (BPV II)
C. W. Rowley, Chair P. S. HillF. L. Brown M. R. KesslerS. R.
Frost F. WorthM. Golliet
COMMITTEE ON CONSTRUCTION OF NUCLEAR FACILITYCOMPONENTS
(III)
R. W. Barnes, Chair J. D. StevensonR. M. Jessee, Vice Chair K.
R. WichmanC. A. Sanna, Staff Secretary C. S. WithersW. H. Borter Y.
H. Choi, DelegateM. N. Bressler T. Ius, DelegateT. D. Burchell C.
C. Kim, ContributingJ. R. Cole MemberR. P. Deubler E. B. Branch,
HonoraryB. A. Erler MemberG. M. Foster G. D. Cooper, HonoraryR. S.
Hill III MemberC. L. Hoffmann W. D. Doty, HonoraryV. Kostarev
MemberW. C. LaRochelle D. F. Landers, HonoraryK. A. Manoly MemberW.
N. McLean R. A. Moen, HonoraryM. N. Mitchell MemberD. K. Morton C.
J. Pieper, HonoraryR. F. Reedy Member
Subgroup on Containment Systems for Spent Fueland High-Level
Waste Transport Packagings (BPV III)
G. M. Foster, Chair P. E. McConnellG. J. Solovey, Vice Chair I.
D. McInnesD. K. Morton, Secretary A. B. MeichlerD. J. Ammerman R.
E. NickellW. G. Beach E. L. PleinsG. Bjorkman T. SaegusaW. H.
Borter H. P. ShrivastavaG. R. Cannell N. M. SimpsonE. L. Farrow R.
H. SmithR. S. Hill III J. D. StevensonS. Horowitz C. J. TemusD. W.
Lewis A. D. WatkinsC. G. May
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
标准分享网 www.bzfxw.com 免费下载
-
www.bzfxw.com
Subgroup on Design (BPV III)
R. P. Deubler, Chair D. F. LandersR. S. Hill III, Vice Chair K.
A. ManolyA. N. Nguyen, Secretary R. J. MastersonT. M. Adams W. N.
McLeanS. Asada J. C. MinichielloM. N. Bressler M. MorishitaC. W.
Bruny E. L. PleinsJ. R. Cole I. SaitoR. E. Cornman, Jr. G. C.
SlagisA. A. Dermenjian J. D. StevensonP. Hirschberg J. P. TuckerR.
I. Jetter K. R. WichmanR. B. Keating J. YangJ. F. Kielb T. Ius,
DelegateH. Kobayashi
Working Group on Supports (SG-D) (BPV III)
R. J. Masterson, Chair A. N. NguyenF. J. Birch, Secretary I.
SaitoK. Avrithi J. R. StinsonU. S. Bandyopadhyay T. G. TerryahR. P.
Deubler G. Z. TokarskiW. P. Golini C.-I. Wu
Working Group on Core Support Structures (SG-D) (BPV III)
J. Yang, Chair H. S. MehtaJ. F. Kielb, Secretary J. F.
MulloolyF. G. Al-Chammas A. TsirigotisJ. T. Land
Working Group on Design Methodology (SG-D) (BPV III)
R. B. Keating, Chair J. D. StevensonS. D. Snow, Secretary A.
TsirigotisK. Avrithi T. M. WigerM. Basol J. YangD. L. Caldwell D.
F. Landers, CorrespondingH. T. Harrison III MemberP. Hirschberg M.
K. Au-Yang, ContributingH. Kobayashi MemberH. Lockert R. D.
Blevins, ContributingJ. F. McCabe MemberA. N. Nguyen W. S. Lapay,
ContributingD. H. Roarty MemberE. A. Rodriguez
Working Group on Design of Division 3 Containments(SG-D) (BPV
III)
E. L. Pleins, Chair H. P. ShrivastavaD. J. Ammerman C. J.
TemusG. Bjorkman I. D. McInnes, ContributingS. Horowitz MemberD. W.
Lewis R. E. Nickell, ContributingJ. C. Minichiello MemberD. K.
Morton
xiii
Working Group on Piping (SG-D) (BPV III)
P. Hirschberg, Chair E. R. NelsonG. Z. Tokarski, Secretary A. N.
NguyenT. M. Adams N. J. ShahG. A. Antaki M. S. SillsC. Basavaraju
G. C. SlagisJ. Catalano N. C. SutherlandJ. R. Cole E. A. WaisM. A.
Gray C.-I. WuR. W. Haupt D. F. Landers, CorrespondingJ. Kawahata
MemberR. B. Keating R. D. Patel, ContributingV. Kostarev MemberY.
Liu E. C. Rodabaugh, ContributingJ. F. McCabe MemberJ. C.
Minichiello
Working Group on Probabilistic Methods in Design(SG-D) (BPV
III)
R. S. Hill III, Chair M. MorishitaT. Asayama P. J. O’ReganK.
Avrithi N. A. PalmB. M. Ayyub I. SaitoA. A. Dermenjian M. E.
SchmidtM. R. Graybeal A. TsirigotisD. O. Henry J. P. TuckerS. D.
Kulat R. M. WilsonA. McNeill III
Working Group on Pumps (SG-D) (BPV III)
R. E. Cornman, Jr., Chair R. A. LadefianP. W. Behnke J. W.
LeavittM. D. Eftychiou R. A. PatrickA. Fraser J. R. RajanR.
Ghanbari R. UdoM. Higuchi A. G. WashburnC. J. Jerz
Working Group on Valves (SG-D) (BPV III)
J. P. Tucker, Chair J. O’CallaghanG. A. Jolly J. D. PageW. N.
McLean S. N. ShieldsT. A. McMahon H. R. SondereggerC. A. Mizer J.
C. Tsacoyeanes
Working Group on Vessels (SG-D) (BPV III)
G. K. Miller, Secretary O.-S. KimC. Basavaraju K. MatsunagaC. W.
Bruny D. E. MatthewsJ. V. Gregg C. TuryloW. J. Heilker W. F.
WeitzeA. Kalnins R. M. WilsonR. B. Keating
Special Working Group on Environmental Effects (SG-D) (BPV
III)
W. Z. Novak, Chair C. L. HoffmannR. S. Hill III Y. H. Choi,
Delegate
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
-
www.bzfxw.com
Subgroup on General Requirements (BPV III & 3C)
W. C. LaRochelle, Chair M. R. MinickL. M. Plante, Secretary B.
B. ScottA. Appleton C. T. SmithJ. R. Berry W. K. Sowder, Jr.J. V.
Gardiner D. M. VickeryW. P. Golini D. V. WalsheG. L. Hollinger C.
S. WithersE. A. Mayhew H. Michael, DelegateR. P. McIntyre
Working Group on Duties and Responsibilities (SG-GR) (BPV
III)
J. V. Gardiner, Chair A. T. KeimG. L. Hollinger, Secretary M. A.
LockwoodJ. R. Berry L. M. PlanteM. E. Jennings D. J. RoszmanK. A.
Kavanagh S. Scardigno
Working Group on Quality Assurance, Certification, andStamping
(SG-GR) (BPV III)
C. T. Smith, Chair M. R. MinickC. S. Withers, Secretary R. B.
PatelA. Appleton S. J. SalvadorB. K. Bobo W. K. Sowder, Jr.S. M.
Goodwin M. F. SullivanJ. W. Highlands G. E. SzabaturaR. P. McIntyre
D. M. Vickery
Subgroup on Materials, Fabrication, and Examination (BPV
III)
C. L. Hoffmann, Chair C. C. KimW. G. Beach M. LauW. H. Borter H.
MurakamiG. R. Cannell N. M. SimpsonR. H. Davis W. J. SperkoD. M.
Doyle J. R. StinsonG. M. Foster J. F. StrunkB. D. Frew K. B.
StuckeyG. B. Georgiev A. D. WatkinsS. E. Gingrich H. Michael,
DelegateR. M. Jessee
Subgroup on Pressure Relief (BPV III)
J. F. Ball, Chair A. L. SzeglinE. M. Petrosky D. G. Thibault
Subgroup on Strategy and Management(BPV III, Divisions 1 and
2)
R. W. Barnes, Chair E. V. ImbroC. A. Sanna, Staff Secretary R.
M. JesseeB. K. Bobo K. A. ManolyN. Broom D. K. MortonJ. R. Cole J.
RamirezB. A. Erler R. F. ReedyC. M. Faidy C. T. SmithJ. M. Helmey
W. K. Sowder, Jr.M. F. Hessheimer Y. UrabeR. S. Hill III
xiv
Special Working Group on Editing and Review (BPV III)
R. F. Reedy, Chair B. A. ErlerW. H. Borter W. C. LaRochelleM. N.
Bressler J. D. StevensonR. P. Deubler
Special Working Group on Polyethylene Pipe (BPV III)
J. C. Minichiello, Chair P. KrishnaswamyT. M. Adams E. LeverW.
I. Adams E. W. McElroyG. A. Antaki D. P. MunsonC. Basavaraju T. M.
MustoD. Burwell L. J. PetroffJ. M. Craig C. W. RowleyR. R. Croft F.
J. Schaaf, Jr.E. L. Farrow C. T. SmithE. M. Focht H. E. SvetlikM.
Golliet D. M. VickeryA. N. Haddad Z. J. ZhouR. S. Hill III
Working Group on Nuclear High-TemperatureGas-Cooled Reactors
(BPV III)
N. Broom, Chair T. R. LupoldT. D. Burchell D. L. MarriottM. F.
Hessheimer D. K. MortonR. S. Hill III T.-L. ShamE. V. Imbro Y.
TachibanaR. I. Jetter T. YuharaY. W. Kim
Subgroup on Graphite Core Components (BPV III)
T. D. Burchell, Chair M. P. HindleyC. A. Sanna, Staff Secretary
Y. KatohR. L. Bratton M. N. MitchellS.-H. Chi N. N. NemethM. W.
Davies T. OkuS. W. Doms T. ShibataS. F. Duffy M. SrinivasanO.
Gelineau A. G. SteerG. O. Hayner S. Yu
Subgroup on Industry Experience for New Plants(BPV III & BPV
XI)
G. M. Foster, Chair K. MatsunagaJ. T. Lindberg, Chair R. E.
McLaughlinH. L. Gustin, Secretary A. McNeill IIIM. L. Coats H.
MurakamiA. A. Dermenjian R. D. PatelJ. Fletcher J. C. PoehlerE. B.
Gerlach D. W. SanduskyH. L. Gustin R. R. SchaeferD. O. Henry D. M.
SwannE. V. Imbro E. R. WillisC. C. Kim C. S. WithersO.-S. Kim S. M.
Yee
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
标准分享网 www.bzfxw.com 免费下载
-
www.bzfxw.com
Subgroup on Magnetic Confinement Fusion Energy Devices(BPV
III)
W. K. Sowder, Jr., Chair S. LeeR. W. Barnes G. LiM. Higuchi X.
LiK. H. Jong D. RoszmanK. A. Kavanagh S. J. SalvadorH.-J. Kim
Subgroup on Nuclear High-Temperature Reactors (BPV III)
M. Morishita, Chair G. H. KooR. I. Jetter, Vice Chair D. K.
MortonT.-L. Sham, Secretary J. E. NestellN. Broom
Working Group on Fusion Energy Devices (BPV III)
W. K. Sowder, Jr., Chair
Working Group on Liquid Metal Reactors (BPV III)
T.-L. Sham, Chair G. H. KooT. Asayama, Secretary M. LiR. W.
Barnes S. MajumdarC. M. Faidy M. MorishitaR. I. Jetter J. E.
Nestell
Special Working Group on Bolted Flanged Joints (BPV III)
R. W. Mikitka, Chair W. J. KovesG. D. Bibel M. S. SheltonW.
Brown
Subgroup on Design Analysis (BPV III)
G. L. Hollinger, Chair W. J. KovesS. A. Adams K. MatsunagaM. R.
Breach G. A. MillerR. G. Brown W. D. ReinhardtT. M. Damiani D. H.
RoartyR. J. Gurdal G. SannazzaroB. F. Hantz T. G. SeippC. F.
Heberling II G. TaxacherC. E. Hinnant W. F. WeitzeD. P. Jones R. A.
WhippleA. Kalnins K. Wright
Subgroup on Elevated Temperature Design (BPV III)
R. I. Jetter, Chair A. B. HullJ. J. Abou-Hanna M. H. JawadT.
Asayama G. H. KooC. Becht W. J. KoovesF. W. Brust D. L. MarriottP.
Carter T. E. McGreevyJ. F. Cervenka J. E. NestellB. Dogan W. J.
O’DonnellD. S. Griffin T.-L. ShamB. F. Hantz R. W. Swindeman
xv
Subgroup on Fatigue Strength (BPV III)
W. J. O’Donnell, Chair D. P. JonesS. A. Adams G. KharshafdjianG.
S. Chakrabarti S. MajumdarT. M. Damiani S. N. MalikP. R. Donavin D.
H. RoartyR. J. Gurdal G. TaxacherC. F. Heberling II A. TsirigotisC.
E. Hinnant K. WrightP. Hirschberg H. H. Ziada
JOINT ACI-ASME COMMITTEE ONCONCRETE COMPONENTS FOR NUCLEAR
SERVICE (BPV 3C)
A. C. Eberhardt, Chair O. JovallC. T. Smith, Vice Chair N.-H.
LeeM. L. Vazquez, Staff Secretary J. MunshiN. Alchaar N. OrbovicJ.
F. Artuso B. B. ScottH. G. Ashar R. E. ShewmakerC. J. Bang J. D.
StevensonB. A. Erler M. K. ThummF. Farzam M. L. WilliamsP. S.
Ghosal T. D. Al-Shawaf, ContributingJ. Gutierrez MemberJ. K.
Harrold T. Muraki, ContributingG. A. Harstead MemberM. F.
Hessheimer M. R. Senecal, ContributingT. C. Inman MemberT. E.
Johnson
Working Group on Materials, Fabrication, and Examination(BPV
3C)
J. F. Artuso, Chair J. GutierrezP. S. Ghosal, Vice Chair B. B.
ScottM. L. Williams, Secretary C. T. SmithA. C. Eberhardt
Working Group on Modernization (BPV 3C)
N. Alchaar, Chair J. F. ArtusoO. Jovall, Vice Chair J. K.
HarroldC. T. Smith, Secretary
COMMITTEE ON HEATING BOILERS (IV)
P. A. Molvie, Chair D. J. JenkinsT. L. Bedeaux, Vice Chair P. A.
LarkinG. Moino, Staff Secretary K. M. McTagueJ. Calland B. W.
MooreJ. P. Chicoine T. M. ParksC. M. Dove J. L. SeigleB. G. French
R. V. WielgoszinskiW. L. Haag, Jr. H. Michael, DelegateJ. A. Hall
E. A. Nordstrom, AlternateA. Heino
Subgroup on Care and Operation of Heating Boilers (BPV IV)
K. M. McTague P. A. Molvie
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
-
www.bzfxw.com
Subgroup on Cast Iron Boilers (BPV IV)
K. M. McTague, Chair A. P. JonesT. L. Bedeaux, Vice Chair V. G.
KleftisJ. P. Chicoine J. KliessB. G. French P. A. LarkinJ. A. Hall
E. A. Nordstrom
Subgroup on Materials (BPV IV)
P. A. Larkin, Chair B. J. IskeJ. A. Hall, Vice Chair J. KliessA.
Heino J. L. Seigle
Subgroup on Water Heaters (BPV IV)
W. L. Haag, Jr., Chair K. M. McTagueJ. Calland, Vice Chair O. A.
MissoumJ. P. Chicoine R. E. OlsonB. G. French F. J. SchreinerT. D.
Gantt M. A. TaylorB. J. Iske T. E. TrantA. P. Jones
Subgroup on Welded Boilers (BPV IV)
T. L. Bedeaux, Chair E. A. NordstromJ. Calland, Vice Chair R. E.
OlsonC. M. Dove J. L. SeigleB. G. French R. V. WielgoszinskiA. P.
Jones H. Michael, Delegate
COMMITTEE ONNONDESTRUCTIVE EXAMINATION (V)
J. E. Batey, Chair A. B. NagelF. B. Kovacs, Vice Chair C. A.
NoveJ. Brzuszkiewicz, Staff T. L. Plasek
Secretary F. J. SattlerS. J. Akrin G. M. Gatti, DelegateC. A.
Anderson B. H. Clark, Jr., HonoraryJ. E. Aycock MemberA. S. Birks
H. C. Graber, HonoraryP. L. Brown MemberN. Y. Faransso O. F.
Hedden, HonoraryA. F. Garbolevsky MemberG. W. Hembree J. R. MacKay,
HonoraryR. W. Kruzic MemberJ. R. McGimpsey T. G. McCarty,
HonoraryM. D. Moles Member
Subgroup on General Requirements/Personnel Qualifications and
Inquiries (BPV V)
F. B. Kovacs, Chair G. W. HembreeC. A. Anderson J. W. HoufJ. E.
Batey J. R. MacKayA. S. Birks J. P. Swezy, Jr.N. Y. Faransso
xvi
Subgroup on Surface Examination Methods (BPV V)
A. S. Birks, Chair G. W. HembreeS. J. Akrin R. W. KruzicP. L.
Brown C. A. NoveB. Caccamise F. J. SattlerN. Y. Faransso F. C.
TurnbullN. Farrenbaugh G. M. Gatti, DelegateN. A. Finney
Subgroup on Volumetric Methods (BPV V)
G. W. Hembree, Chair F. B. KovacsS. J. Akrin R. W. KruzicJ. E.
Aycock J. R. McGimpseyJ. E. Batey M. D. MolesP. L. Brown A. B.
NagelB. Caccamise C. A. NoveN. Y. Faransso T. L. PlasekA. F.
Garbolevsky F. J. SattlerR. W. Hardy G. M. Gatti, DelegateR. A.
Kellerhall
Working Group on Acoustic Emissions (SG-VM) (BPV V)
N. Y. Faransso, Chair J. E. BateyJ. E. Aycock R. K. Miller
Working Group on Radiography (SG-VM) (BPV V)
F. B. Kovacs, Chair G. W. HembreeS. J. Akrin R. W. KruzicJ. E.
Aycock J. R. McGimpseyJ. E. Batey R. J. MillsP. L. Brown A. B.
NagelB. Caccamise C. A. NoveN. Y. Faransso T. L. PlasekA. F.
Garbolevsky F. C. TurnbullR. W. Hardy D. E. Williams
Working Group on Ultrasonics (SG-VM) (BPV V)
R. W. Kruzic, Chair R. A. KellerhallJ. E. Aycock M. D. MolesB.
Caccamise A. B. NagelN. Y. Faransso C. A. NoveN. A. Finney F. J.
SattlerO. F. Hedden
COMMITTEE ON PRESSURE VESSELS (VIII)
T. P. Pastor, Chair D. T. PetersU. R. Miller, Vice Chair M. J.
PischkeS. J. Rossi, Staff Secretary M. D. RanaT. Schellens, Staff
Secretary G. B. Rawls, Jr.R. J. Basile S. C. RobertsJ. Cameron C.
D. RoderyD. B. DeMichael A. SelzJ. P. Glaspie J. R. Sims, Jr.M.
Gold D. A. SwansonJ. F. Grubb K. K. TamL. E. Hayden, Jr. S.
TeradaG. G. Karcher E. UpitisK. T. Lau P. A. McGowan, DelegateJ. S.
Lee H. Michael, DelegateR. Mahadeen K. Oyamada, DelegateS. Malone
M. E. Papponetti, DelegateR. W. Mikitka D. Rui, DelegateK.
Mokhtarian T. Tahara, DelegateC. C. Neely W. S. Jacobs,
ContributingT. W. Norton MemberD. A. Osage
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
标准分享网 www.bzfxw.com 免费下载
-
www.bzfxw.com
Subgroup on Design (BPV VIII)
U. R. Miller, Chair C. D. RoderyR. J. Basile, Vice Chair A.
SelzM. D. Lower, Secretary S. C. ShahO. A. Barsky J. C. SowinskiM.
R. Breach C. H. SturgeonF. L. Brown D. A. SwansonJ. R. Farr K. K.
TamC. E. Hinnant J. VattappillyM. H. Jawad R. A. WhippleR. W.
Mikitka A. H. Gibbs, DelegateK. Mokhtarian K. Oyamada, DelegateD.
A. Osage M. E. Papponetti, DelegateT. P. Pastor W. S. Jacobs,
CorrespondingM. D. Rana MemberG. B. Rawls, Jr. E. L. Thomas, Jr.,
HonoraryS. C. Roberts Member
Subgroup on Fabrication and Inspection (BPV VIII)
C. D. Rodery, Chair J. S. LeeJ. P. Swezy, Jr., Vice Chair D. A.
OsageB. R. Morelock, Secretary M. J. PischkeJ. L. Arnold M. J.
RiceW. J. Bees B. F. ShelleyL. F. Campbell P. L. SturgillH. E.
Gordon T. TaharaW. S. Jacobs K. Oyamada, DelegateD. J. Kreft R.
Uebel, Delegate
Subgroup on General Requirements (BPV VIII)
S. C. Roberts, Chair C. C. NeelyD. B. DeMichael, Vice Chair A.
S. OlivaresF. L. Richter, Secretary D. B. StewartR. J. Basile D. A.
SwansonD. T. Davis K. K. TamJ. P. Glaspie A. H. Gibbs, DelegateL.
E. Hayden, Jr. K. Oyamada, DelegateK. T. Lau R. Uebel, DelegateM.
D. Lower
Subgroup on Heat Transfer Equipment (BPV VIII)
R. Mahadeen, Chair D. L. KurleT. W. Norton, Vice Chair B. J.
LerchG. Aurioles S. MayeuxS. R. Babka U. R. MillerJ. H. Barbee R.
J. StastnyO. A. Barsky K. Oyamada, DelegateI. G. Campbell F.
Osweiller, CorrespondingA. Chaudouet MemberM. D. Clark S. Yokell,
CorrespondingJ. I. Gordon MemberM. J. Holtz S. M. Caldwell,
HonoraryF. E. Jehrio MemberG. G. Karcher
xvii
Subgroup on High-Pressure Vessels (BPV VIII)
D. T. Peters, Chair S. C. MordreA. P. Maslowski, Staff E. A.
Rodriguez
Secretary E. D. RollL. P. Antalffy J. R. Sims, Jr.R. C. Biel D.
L. StangP. N. Chaku F. W. TatarR. Cordes S. TeradaR. D. Dixon R.
WinkD. M. Fryer K. Oyamada, DelegateR. T. Hallman L. Fridlund,
CorrespondingA. H. Honza MemberM. M. James M. D. Mann,
ContributingP. Jansson MemberJ. A. Kapp G. J. Mraz, ContributingJ.
Keltjens MemberD. P. Kendall D. J. Burns, Honorary MemberA. K.
Khare E. H. Perez, Honorary
Member
Subgroup on Materials (BPV VIII)
J. F. Grubb, Chair K. Oyamada, DelegateJ. Cameron,Vice Chair E.
E. Morgenegg,P. G. Wittenbach, Secretary Corresponding MemberA. Di
Rienzo E. G. Nisbett, CorrespondingM. Gold MemberM. Katcher G. S.
Dixit, ContributingW. M. Lundy MemberD. W. Rahoi J. A. McMaster,
ContributingR. C. Sutherlin MemberE. Upitis
Subgroup on Toughness (BPV II & BPV VIII)
D. A. Swanson, Chair C. C. NeelyJ. L. Arnold M. D. RanaR. J.
Basile F. L. RichterJ. Cameron J. P. Swezy, Jr.H. E. Gordon E.
UpitisW. S. Jacobs J. VattappillyK. Mokhtarian K. Oyamada,
Delegate
Special Working Group on Graphite Pressure Equipment(BPV
VIII)
S. Malone, Chair R. W. DickersonE. Soltow, Vice Chair B.
LukaschT. F. Bonn M. R. MinickF. L. Brown A. A. Stupica
Task Group on Impulsively Loaded Vessels (BPV VIII)
R. E. Nickell, Chair D. HildingG. A. Antaki K. W. KingJ. K.
Asahina R. KitamuraD. D. Barker R. A. LeishearR. C. Biel P.
LeslieD. W. Bowman F. OhlsonA. M. Clayton D. T. PetersJ. E.
Didlake, Jr. E. A. RodriguezT. A. Duffey C. RomeroB. L. Haroldsen
J. E. ShepherdH. L. Heaton
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
-
www.bzfxw.com
COMMITTEE ON WELDING AND BRAZING (IX)
J. G. Feldstein, Chair M. J. PischkeW. J. Sperko, Vice Chair M.
J. RiceS. J. Rossi, Staff Secretary M. B. SimsD. A. Bowers M. J.
StankoR. K. Brown, Jr. J. P. Swezy, Jr.M. L. Carpenter P. L. Van
FossonP. D. Flenner R. R. YoungR. M. Jessee S. Raghunathan,
ContributingJ. S. Lee MemberW. M. Lundy S. D. Reynolds, Jr.,T.
Melfi Contributing MemberW. F. Newell, Jr. W. D. Doty, HonoraryB.
R. Newmark MemberA. S. Olivares
Subgroup on Brazing (BPV IX)
M. J. Pischke, Chair M. L. CarpenterE. W. Beckman A. F.
GarbolevskyL. F. Campbell J. P. Swezy, Jr.
Subgroup on General Requirements (BPV IX)
B. R. Newmark, Chair H. B. PorterE. W. Beckman P. L. SturgillP.
R. Evans K. R. WillensR. M. Jessee E. Molina, DelegateA. S.
Olivares
Subgroup on Materials (BPV IX)
S. E. Gingrich C. E. SainzR. M. Jessee W. J. SperkoC. C. Kim M.
J. StankoT. Melfi R. R. YoungS. D. Reynolds, Jr. V. Giunto,
Delegate
Subgroup on Performance Qualification (BPV IX)
D. A. Bowers, Chair K. L. HayesV. A. Bell J. S. LeeL. P. Connor
W. M. LundyR. B. Corbit E. G. ReicheltP. R. Evans M. B. SimsP. D.
Flenner G. W. Spohn III
Subgroup on Procedure Qualification (BPV IX)
D. A. Bowers, Chair M. B. SimsM. J. Rice, Secretary W. J.
SperkoM. Bernasek S. A. SpragueR. K. Brown, Jr. J. P. Swezy, Jr.J.
R. McGimpsey P. L. Van FossonW. F. Newell, Jr. T. C. WiesnerA. S.
Olivares E. Molina, DelegateS. D. Reynolds, Jr.
xviii
COMMITTEE ONFIBER-REINFORCED PLASTIC PRESSURE VESSELS (X)
D. Eisberg, Chair D. L. KeelerP. J. Conlisk, Vice Chair B. M.
LinnemannP. D. Stumpf, Staff Secretary N. L. NewhouseF. L. Brown D.
J. PainterJ. L. Bustillos G. RamirezT. W. Cowley J. R. RichterI. L.
Dinovo J. A. RolstonT. J. Fowler B. F. ShelleyM. R. Gorman F. W.
Van NameD. H. Hodgkinson D. O. Yancey, Jr.L. E. Hunt P. H.
Ziehl
COMMITTEE ONNUCLEAR INSERVICE INSPECTION (XI)
G. C. Park, Chair D. A. ScarthR. W. Swayne, Vice Chair F. J.
Schaaf, Jr.R. L. Crane, Staff Secretary J. C. Spanner, Jr.W. H.
Bamford, Jr. G. L. StevensC. B. Cantrell K. B. ThomasR. C. Cipolla
E. W. Throckmorton IIIM. L. Coats D. E. WaskeyD. D. Davis R. A.
WestR. L. Dyle C. J. WirtzE. L. Farrow R. A. YonekawaJ. Fletcher K.
K. YoonE. B. Gerlach T. YuharaR. E. Gimple Y.-S. Chang, DelegateF.
E. Gregor J. T. Lindberg, AlternateK. Hasegawa L. J. Chockie,
HonoraryD. O. Henry MemberJ. C. Keenan C. D. Cowfer, HonoraryR. D.
Kerr MemberS. D. Kulat O. F. Hedden, HonoraryG. L. Lagleder
MemberD. W. Lamond L. R. Katz, Honorary MemberG. A. Lofthus P. C.
Riccardella, HonoraryW. E. Norris MemberK. Rhyne
Executive Committee (BPV XI)
R. W. Swayne, Chair W. E. NorrisG. C. Park, Vice Chair K.
RhyneR. L. Crane, Staff Secretary J. C. Spanner, Jr.W. H. Bamford,
Jr. K. B. ThomasR. L. Dyle R. A. WestR. E. Gimple R. A. YonekawaJ.
T. Lindberg
Subgroup on Evaluation Standards (SG-ES) (BPV XI)
W. H. Bamford, Jr., Chair K. KoyamaG. L. Stevens, Secretary D.
R. LeeH.-D. Chung H. S. MehtaR. C. Cipolla J. G. MerkleG. H. DeBoo
M. A. MitchellR. L. Dyle K. MiyazakiB. R. Ganta S. RanganathT. J.
Griesbach D. A. ScarthK. Hasegawa T.-L. ShamK. Hojo K. R. WichmanD.
N. Hopkins K. K. YoonY. Imamura Y.-S. Chang, Delegate
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
标准分享网 www.bzfxw.com 免费下载
-
www.bzfxw.com
Working Group on Flaw Evaluation (SG-ES) (BPV XI)
R. C. Cipolla, Chair H. S. MehtaG. H. DeBoo, Secretary J. G.
MerkleW. H. Bamford, Jr. K. MiyazakiM. Basol R. K. QashuB. Bezensek
S. RanganathJ. M. Bloom D. L. RudlandH.-D. Chung P. J. RushB. R.
Ganta D. A. ScarthR. G. Gilada W. L. ServerT. J. Griesbach N. J.
ShahH. L. Gustin T. V. VoF. D. Hayes K. R. WichmanP. H. Hoang G. M.
WilkowskiK. Hojo S. X. XuD. N. Hopkins K. K. YoonK. Koyama V. A.
ZilbersteinD. R. Lee
Working Group on Operating Plant Criteria (SG-ES) (BPV XI)
T. J. Griesbach, Chair M. A. MitchellW. H. Bamford, Jr. R.
PaceH. Behnke S. RanganathB. A. Bishop W. L. ServerT. L. Dickson E.
A. SiegelR. L. Dyle D. V. SommervilleS. R. Gosselin G. L. StevensM.
Hayashi D. P. WeaklandH. S. Mehta K. K. Yoon
Working Group on Pipe Flaw Evaluation (SG-ES) (BPV XI)
D. A. Scarth, Chair K. HojoG. M. Wilkowski, Secretary D. N.
HopkinsT. A. Bacon K. KashimaW. H. Bamford, Jr. R. O. McGillB.
Bezensek H. S. MehtaH.-D. Chung K. MiyazakiR. C. Cipolla D. L.
RudlandN. G. Cofie P. J. RushJ. M. Davis T.-L. ShamG. H. DeBoo T.
V. VoB. Dogan B. S. WasilukB. R. Ganta S. X. XuL. F. Goyette K. K.
YoonK. Hasegawa V. A. ZilbersteinP. H. Hoang
Subgroup on Nondestructive Examination (SG-NDE) (BPV XI)
J. C. Spanner, Jr., Chair D. O. HenryG. A. Lofthus, Secretary D.
KurekC. A. Anderson G. L. LaglederT. L. Chan J. T. LindbergC. B.
Cheezem G. R. PerkinsD. R. Cordes A. S. ReedF. E. Dohmen F. J.
Schaaf, Jr.M. E. Gothard C. J. Wirtz
xix
Working Group on Personnel Qualification and SurfaceVisual and
Eddy Current Examination (SG-NDE) (BPV XI)
A. S. Reed, Chair J. W. HoufD. R. Cordes, Secretary J. T.
LindbergC. A. Anderson D. R. Quattlebaum, Jr.B. L. Curtis D.
SpakeN. Farenbaugh J. C. Spanner, Jr.D. O. Henry M. C. WeatherlyK.
M. Hoffman C. J. Wirtz
Working Group on Procedure Qualificationand Volumetric
Examination (SG-NDE) (BPV XI)
M. E. Gothard, Chair R. A. KellerhallG. R. Perkins, Secretary D.
KurekM. T. Anderson G. A. LofthusC. B. Cheezem C. E. MoyerA. D.
Chockie S. A. SaboS. R. Doctor R. V. SwainF. E. Dohmen S. J. ToddK.
J. Hacker
Subgroup on Repair/Replacement Activities (SG-RRA) (BPV XI)
R. A. Yonekawa, Chair J. C. KeenanE. V. Farrell, Jr., Secretary
R. D. KerrS. B. Brown S. L. McCrackenR. E. Cantrell B. R. NewtonP.
D. Fisher J. E. O’SullivanJ. M. Gamber R. R. StevensonE. B. Gerlach
R. W. SwayneR. E. Gimple D. E. WaskeyD. R. Graham J. G. WeicksR. A.
Hermann E. G. Reichelt, AlternateK. J. Karwoski
Working Group on Welding and Special Repair Processes(SG-RRA)
(BPV XI)
D. E. Waskey, Chair M. LauD. J. Tilly, Secretary S. L.
McCrackenR. E. Cantrell D. B. MeredithS. J. Findlan B. R. NewtonP.
D. Fisher J. E. O’SullivanM. L. Hall G. R. PolingR. A. Hermann R.
E. SmithK. J. Karwoski J. G. WeicksC. C. Kim K. R. Willens
Working Group on Design and Programs (SG-RRA) (BPV XI)
E. B. Gerlach, Chair D. R. GrahamS. B. Brown, Secretary G. F.
HarttraftO. Bhatty T. E. HissJ. W. Collins M. A. PyneR. R. Croft R.
R. StevensonG. G. Elder R. W. SwayneE. V. Farrell, Jr. A. H.
TaufiqueS. K. Fisher T. P. Vassallo, Jr.J. M. Gamber R. A.
Yonekawa
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
-
www.bzfxw.com
Subgroup on Water-Cooled Systems (SG-WCS) (BPV XI)
K. B. Thomas, Chair S. D. KulatN. A. Palm, Secretary D. W.
LamondJ. M. Agold A. McNeill IIIV. L. Armentrout T. NomuraJ. M.
Boughman W. E. NorrisS. T. Chesworth G. C. ParkM. L. Coats J. E.
StaffieraD. D. Davis E. W. Throckmorton IIIH. Q. Do R. A. WestE. L.
Farrow G. E. WhitmanM. J. Ferlisi H. L. Graves III, AlternateO. F.
Hedden
Working Group on Containment (SG-WCS) (BPV XI)
J. E. Staffiera, Chair H. L. Graves IIIH. M. Stephens, Jr.,
Secretary H. T. HillS. G. Brown R. D. HoughR. C. Cox C. N.
KrishnaswamyJ. W. Crider D. J. NausM. J. Ferlisi F. Poteet IIIP. S.
Ghosal G. ThomasD. H. Goche W. E. Norris, Alternate
Working Group on ISI Optimization (SG-WCS) (BPV XI)
D. R. Cordes, Chair A. H. MahindrakarS. A. Norman, Secretary S.
A. SaboW. H. Bamford, Jr. S. R. ScottJ. M. Boughman E. A. SiegelJ.
W. Collins K. B. ThomasM. E. Gothard G. E. WhitmanR. E. Hall Y.
Yuguchi
Working Group on Implementation of Risk-Based
Examination(SG-WCS) (BPV XI)
S. D. Kulat, Chair K. M. HoffmanS. T. Chesworth, Secretary A. T.
KeimJ. M. Agold D. W. LamondB. A. Bishop J. T. LewisC.
Cueto-Felgueroso R. K. MattuH. Q. Do A. McNeill IIIR. Fougerousse
P. J. O’ReganM. R. Graybeal N. A. PalmJ. Hakii M. A. PyneK. W. Hall
J. C. Younger
Working Group on Inspection of Systems and Components(SG-WCS)
(BPV XI)
J. M. Agold, Chair S. D. KulatV. L. Armentrout, Secretary T. A.
MeyerC. Cueto-Felgueroso D. G. NaujockH. Q. Do T. NomuraM. J.
Ferlisi C. M. RossR. Fougerousse K. B. ThomasK. W. Hall G. E.
Whitman
xx
Working Group on Pressure Testing (SG-WCS) (BPV XI)
D. W. Lamond, Chair R. E. HallJ. M. Boughman, Secretary A.
McNeill IIIY.-K. Chung B. L. MontgomeryJ. J. Churchwell P. N.
PassalugoT. Coste E. J. Sullivan, Jr.J. A. Doughty E. W.
Throckmorton IIIG. L. Fechter IV
Special Working Group on Editing and Review (BPV XI)
R. W. Swayne, Chair J. E. StaffieraC. E. Moyer D. J. TillyK. R.
Rao C. J. Wirtz
Special Working Group on Nuclear Plant Aging (BPV XI)
T. A. Meyer, Chair A. B. MeichlerD. V. Burgess, Secretary R. E.
NickellS. Asada K. SakamotoY.-K. Chung W. L. ServerD. D. Davis R.
L. TurnerF. E. Gregor G. G. YoungA. L. Hiser, Jr. G. E. Carpenter,
Alternate
Special Working Group on High-Temperature Gas-CooledReactors
(BPV XI)
J. Fletcher, Chair A. B. HullM. A. Lockwood, Secretary R. K.
MillerN. Broom M. N. MitchellC. Cueto-Felgueroso T. RoneyK. N.
Fleming F. J. Schaaf, Jr.S. R. Gosselin F. ShahrokhiM. R. Graybeal
R. W. Swayne
Working Group on General Requirements (BPV XI)
K. Rhyne, Chair E. L. FarrowE. J. Maloney, Secretary J. C.
KeenanG. P. Alexander R. K. MattuT. L. Chan S. R. ScottM. L. Coats
G. E. Szabatura
COMMITTEE ON TRANSPORT TANKS (XII)
M. D. Rana, Chair M. D. PhamS. Staniszewski, Vice Chair M.
PittsD. R. Sharp, Staff Secretary T. A. RogersA. N. Antoniou A.
SelzC. H. Hochman W. K. SmithG. G. Karcher A. P. VargheseN. J.
Paulick M. R. Ward
Subgroup on Design and Materials (BPV XII)
A. P. Varghese, Chair M. D. PhamR. C. Sallash, Secretary M. D.
RanaP. Chilukuri T. A. RogersT. Hitchcock A. SelzG. G. Karcher M.
R. WardS. L. McWilliams E. A. WhittleN. J. Paulick
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
标准分享网 www.bzfxw.com 免费下载
-
www.bzfxw.com
Subgroup on Fabrication and Inspection (BPV XII)
J. A. Byers D. J. KreftB. L. Gehl A. S. OlivaresL. D. Holsinger
L. H. Strouse
Subgroup on General Requirements (BPV XII)
C. H. Hochman, Chair J. L. RademacherA. N. Antoniou, Secretary
T. RummelT. W. Alexander R. C. SallashJ. L. Freiler W. K. SmithW.
L. Garfield S. StaniszewskiK. L. Gilmore L. H. StrouseM. Pitts
Subgroup on Nonmandatory Appendices (BPV XII)
T. A. Rogers, Chair S. L. McWilliamsS. Staniszewski, Secretary
M. PittsD. D. Brusewitz J. L. RademacherJ. L. Conley A. SelzT.
Eubanks D. G. SheltonB. L. Gehl A. P. VargheseT. Hitchcock M. R.
Ward
COMMITTEE ON BOILER ANDPRESSURE VESSEL CONFORMITY ASSESSMENT
(CBPVCA)
W. C. LaRochelle, Chair D. C. Cook, AlternateP. D. Edwards, Vice
Chair R. D. Danzy, AlternateK. I. Baron, Staff Secretary M. A.
DeVries, AlternateW. J. Bees G. L. Hollinger, AlternateS. W.
Cameron D. W. King, AlternateT. E. Hansen B. L. Krasiun,
AlternateD. J. Jenkins P. F. Martin, AlternateK. T. Lau K. McPhie,
AlternateL. E. McDonald G. P. Milley, AlternateK. M. McTague M. R.
Minick, AlternateD. Miller T. W. Norton, AlternateB. R. Morelock F.
J. Pavlovicz, AlternateJ. D. O’Leary M. T. Roby, AlternateT. M.
Parks J. A. West, AlternateB. C. Turczynski R. V. Wielgoszinski,
AlternateD. E. Tuttle A. J. Spencer, HonoraryE. A. Whittle MemberS.
F. Harrison, Jr., Contributing
Member
xxi
COMMITTEE ON NUCLEAR CERTIFICATION (CNC)
R. R. Stevenson, Chair M. F. Sullivan, ContributingW. C.
LaRochelle, Vice Chair MemberJ. Pang, Staff Secretary P. D.
Edwards, AlternateM. N. Bressler D. P. Gobbi, AlternateG. Deily J.
W. Highlands, AlternateS. M. Goodwin K. M. Hottle, AlternateK. A.
Huber K. A. Kavanagh, AlternateM. Kotb B. G. Kovarik, AlternateJ.
C. Krane B. L. Krasiun, AlternateR. P. McIntyre M. A. Lockwood,
AlternateM. R. Minick R. J. Luymes, AlternateH. B. Prasse L. M.
Plante, AlternateT. E. Quaka D. W. Stepp, AlternateD. M. Vickery E.
A. Whittle, AlternateC. S. Withers H. L. Wiger, Alternate
COMMITTEE ONSAFETY VALVE REQUIREMENTS (BPV-SVR)
J. A. West, Chair S. F. Harrison, Jr.D. B. DeMichael, Vice Chair
W. F. HartC. E. O’Brien, Staff Secretary D. MillerJ. F. Ball T. M.
ParksS. Cammeresi D. K. ParrishJ. A. Cox T. PatelR. D. Danzy D. J.
ScallanR. J. Doelling Z. WangJ. P. Glaspie
Subgroup on Design (BPV-SVR)
R. D. Danzy, Chair D. MillerC. E. Beair T. PatelJ. A. Conley T.
R. TarbayR. J. Doelling J. A. West
Subgroup on General Requirements (BPV-SVR)
D. B. DeMichael, Chair J. W. RamseyJ. F. Ball J. W. RichardsonG.
Brazier D. E. TuttleJ. P. Glaspie S. T. French, AlternateD. K.
Parrish
Subgroup on Testing (BPV-SVR)
J. A. Cox, Chair W. F. HartJ. E. Britt B. K. NutterS. Cammeresi
D. J. ScallanG. D. Goodson Z. Wang
U.S. Technical Advisory Group ISO/TC 185Safety Relief Valves
T. J. Bevilacqua, Chair D. B. DeMichaelC. E. O’Brien, Staff
Secretary D. MillerJ. F. Ball B. K. NutterG. Brazier J. A. West
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
-
www.bzfxw.com
PERSONNELOfficers of AWS Committee
(Cooperating in the Development of the Specifications
Herein)
As of January 5, 2010
A5 COMMITTEE ON FILLER METALS AND ALLIED MATERIALS
J. S. Lee, Chair L. G. KvidahlH. D. Wehr, 1st Vice Chair A. Y.
LauJ. J. DeLoach, Jr., 2nd Vice W. A. Marttila
Chair T. MelfiR. K. Gupta, Secretary R. MenonT. Anderson M. T.
MerloJ. M. Blackburn B. MosierJ. C. Bundy A. K. MukherjeeD. D.
Crockett T. C. MyersR. V. Decker C. L. NullD. A. DelSignore K. C.
PrudenJ. DeVito S. D. Reynolds, Jr.H. W. Ebert K. RoossinckD. M.
Fedor P. K. SalvesenJ. G. Feldstein K. SampathS. E. Ferree W. S.
SeveranceD. A. Fink M. J. SullivanG. L. Franke R. C. SutherlinR. D.
Fuchs R. A. SwainR. M. Henson K. P. ThornberryS. D. Kiser M. D.
TumuluruP. J. Konkol H. J. WhiteD. J. Kotecki
A5X EXECUTIVE SUBCOMMITTEE
J. S. Lee, Chair J. G. FeldsteinH. D. Wehr, Vice Chair D. A.
FinkJ. J. DeLoach, Jr., 2nd Vice R. D. Fuchs
Chair D. J. KoteckiR. K. Gupta, Secretary R. MenonD. A.
DelSignore R. A. SwainH. W. Ebert
A5A SUBCOMMITTEE ON CARBON AND LOW ALLOY STEELELECTRODES AND
RODS FOR SHIELDED METAL ARC AND
OXYFUEL GAS WELDING
G. L. Franke, Chair T. C. MyersR. A. Swain, Vice Chair J. S.
OgbornR. K. Gupta, Secretary M. P. ParekhJ. J. DeLoach, Jr. M. A.
QuintanaH. W. Ebert P. K. SalvesenK. K. Gupta K. SampathS. J.
Knostman M. S. SierdzinskiA. Y. Lau
xxii
A5B SUBCOMMITTEE ON CARBON AND LOW ALLOY STEELELECTRODES AND
FLUXES FOR SUBMERGED ARC WELDING
T. Melfi, Chair M. T. MerloR. K. Gupta, Secretary D. W. MeyerH.
P. Beck T. C. MyersH. W. Ebert P. J. NicklasS. Francis D. M.
ParkerR. D. Fuchs R. D. StrugarM. J. Ludwig R. A. Swain
A5C SUBCOMMITTEE ON ALUMINUM ALLOY FILLER METALS
T. Anderson, Chair R. M. HensonR. K. Gupta, Secretary G. M.
HergenratherB. E. Anderson J. S. LeeB. C. Boehringer D. A. WrightS.
A. Collins
A5D SUBCOMMITTEE ON STAINLESS STEEL FILLER METALS
D. A. DelSignore, Chair G. A. KuriskyD. J. Kotecki, Vice Chair
F. B. LakeR. K. Gupta, Secretary M. T. MerloR. E. Cantrell S. J.
MerrickJ. G. Feldstein R. A. SwainR. D. Fuchs J. G. WallinS. R.
Jana H. D. WehrS. J. Knostman J. M. Zawodny
A5E SUBCOMMITTEE ON NICKEL AND NICKEL ALLOY FILLERMETALS
R. D. Fuchs, Chair F. B. LakeS. D. Kiser, Vice Chair W. E.
LayoR. K. Gupta, Secretary J. S. LeeG. J. Bruck R. MenonG. S. Clark
S. J. MerrickJ. J. DeLoach, Jr. R. A. SwainS. R. Jana J. F.
TurnerD. D. Kiilunen H. D. WehrG. A. Kurisky H. J. White
A5F SUBCOMMITTEE ON COPPER AND COPPER ALLOY FILLERMETALS
K. Roossinck, Chair J. P. HuntA. R. Mertes, Vice Chair S. D.
Reynolds, Jr.R. K. Gupta, Secretary J. TurriffD. B. Holliday H. D.
Wehr
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
标准分享网 www.bzfxw.com 免费下载
-
www.bzfxw.com
A5G SUBCOMMITTEE ON HARD SURFACING FILLER METALS
R. Menon, Chair W. E. LayoR. K. Gupta, Secretary J. G. PostleF.
Broshjeit V. B. RajanJ. Dezelle A. P. YelistratovS. P. Iyer
A5H SUBCOMMITTEE ON FILLER METALS AND FLUXES FORBRAZING
R. M. Henson, Chair T. P. HirtheG. L. Alexy, Vice Chair M. J.
Lucas, Jr.S. Borrero, Secretary R. P. McKinneyR. K. Gupta,
Secretary W. MigliettiR. Aluru C. R. MoyerP. A. Baskin T. OyamaY.
Baskin J. P. SandsE. R. Boes A. E. ShapiroD. E. Budinger C. M.
VolpeC. F. Darling L. A. WolfgramW. J. Engeron
A5I SUBCOMMITTEE ON TUNGSTEN ELECTRODES
W. S. Severance, Chair M. E. GedgaudasR. K. Gupta, Secretary R.
A. SwainS. G. Caldwell
A5J SUBCOMMITTEE ON ELECTRODES AND RODS FORWELDING CAST IRON
S. D. Kiser, Chair R. A. BishelR. K. Gupta, Secretary R. A.
Bushey
A5K SUBCOMMITTEE ON TITANIUM AND ZIRCONIUM FILLERMETALS
R. C. Sutherlin, Chair B. KruegerJ. C. Monsees, Vice Chair S. D.
SparkowichS. Borrero, Secretary K. T. TranR. K. Gupta, Secretary G.
E. TrepusH. Kotaki M. E. Wells
xxiii
A5L SUBCOMMITTEE ON MAGNESIUM ALLOY FILLER METALS
K. P. Thornberry, Chair R. K. Gupta, Secretary
A5M SUBCOMMITTEE ON CARBON AND LOW ALLOY STEELELECTRODES FOR
FLUX CORED ARC WELDING
D. D. Crockett, Chair L. L. KuiperM. T. Merlo, Vice Chair A. Y.
LauR. K. Gupta, Secretary R. MenonJ. C. Bundy K. M. MerloJ. J.
DeLoach, Jr. J. M. MorseS. E. Ferree T. C. MyersG. L. Franke R. B.
SmithD. Haynie R. A. SwainM. James
A5MILSPEC AD-HOC COMMITTEE ON CONVERSION OFMILITARY
SPECIFICATIONS TO AWS FILLER METAL
SPECIFICATIONS
J. J. DeLoach, Jr., Chair M. J. LudwigR. K. Gupta, Secretary M.
T. MerloJ. C. Bundy T. C. MyersH. R. Castner C. L. NullS. E. Ferree
W. M. RuofD. A. Fink M. J. SulllivanJ. J. Gullotti H. D. WehrP. J.
Konkol
A5N SUBCOMMITTEE ON CONSUMABLE INSERTS
H. D. Wehr, Chair J. J. DeLoach, Jr.W. J. Sperko, Vice Chair W.
F. Newell, Jr.R. K. Gupta, Secretary C. D. Sierra
A5O SUBCOMMITTEE ON CARBON AND LOW ALLOY STEELELECTRODES AND
RODS FOR GAS SHIELDED ARC WELDING
J. C. Bundy, Chair T. C. MyersM. T. Merlo, Vice Chair D. M.
ParkerR. K. Gupta, Secretary V. B. RajanJ. J. DeLoach, Jr. K.
SampathK. W. Gerhart R. B. SmithP. J. Konkol R. D. StrugarL. L.
Kuiper D. A. WrightM. J. Ludwig
A5P SUBCOMMITTEE ON CARBON AND LOW ALLOY STEELELECTRODES FOR
ELECTROSLAG AND ELECTROGAS WELDING
J. S. Lee, Chair D. A. FinkR. K. Gupta, Secretary D. C.
PhillipsJ. H. Devletian R. B. Turpin
A5S SUBCOMMITTEE ON GASES FOR GAS SHIELDED ARCWELDING AND
CUTTING
J. DeVito, Chair B. C. GeorgeJ. M. Zawodny, Vice Chair D. B.
LeturnoR. K. Gupta, Secretary W. H. MeredithE. Colvin F. A.
Schweighardt
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
-
www.bzfxw.com
A5T SUBCOMMITTEE ON FILLER METAL PROCUREMENTGUIDELINES
R. A. Swain, Chair J. S. LeeH. D. Wehr, Vice Chair M. T. MerloR.
K. Gupta, Secretary P. K. SalvesenD. A. Fink K. Sampath
xxiv
A5W SUBCOMMITTEE ON MOISTURE AND HYDROGEN
D. M. Fedor, Chair J. L. KalpJ. M. Blackburn, Vice Chair J.
KeeganR. K. Gupta, Secretary J. S. LeeD. A. Fink M. A. QuintanaG.
L. Franke M. S. Sierdzinski
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---标准分享网
www.bzfxw.com 免费下载
-
www.bzfxw.com
GUIDELINE ON THE APPROVAL OF NEW WELDINGAND BRAZING MATERIAL
CLASSIFICATIONS UNDER
THE ASME BOILER AND PRESSURE VESSEL CODE
Code Policy. It is the policy of the ASME Boiler andPressure
Vessel Committee to adopt for inclusion in Sec-tion II, Part C,
only such specifications as have beenadopted by the American
Welding Society (AWS), and byother recognized national or
international organizations.
It is expected that requests for Code approval will nor-mally be
for welding and brazing materials (hereaftertermed “consumables”)
for which there is a recognizednational or international
specification. For consumablesmade to a recognized national or
international specificationother than those of the AWS, the
inquirer shall give noticeto the standards developing organization
that a request hasbeen made to ASME for adoption of their
specificationunder the ASME Code, and shall request that the
organiza-tion to grant ASME permission to reprint the standard.
Forother consumables, a request shall be made to the AWS,or a
recognized national or international organization, todevelop a
specification that can be presented to the CodeCommittee.
It is the policy of the ASME Boiler and Pressure VesselCommittee
to consider requests to adopt new consumablesfor use by boiler,
pressure vessel, or nuclear power plantcomponent Manufacturers or
end users. Further, suchrequests should be for consumables for
which there is areasonable expectation of use in a boiler, pressure
vessel,or nuclear power plant component constructed to the rulesof
one of the Sections of this Code.
Application. The inquirer shall identify to the Commit-tee all
product forms, size ranges, and specifications forwhich
incorporation is desired, and state whether or notthe consumable is
covered by patents, whether or not it islicensed, and if licensed,
any limitations on its manufacture.
Weldability/Brazability. The inquirer shall furnishcomplete data
on procedure qualification tests made inaccordance with the
requirements of Section IX. Such testsshall be made over the full
range of base metal thicknessin which the consumable is to be used.
Pertinent informa-tion on deposited metal, such as effects from
postweld heattreatment, susceptibility to air hardening, effects of
joiningprocesses, expected notch toughness values, and theamount of
experience in use of the consumable shall begiven.
xxv
Physical Changes. For new consumables, it is importantto know
the structural stability characteristics and thedegree of retention
of properties with exposure at tempera-ture. The influence of
welding or brazing and thermaltreatment operations on the
mechanical properties, ductil-ity, and microstructure of the
deposited metal are impor-tant, particularly where degradation in
properties mayoccur. Where particular temperature ranges of
exposure orheat treatment, cooling rates, combinations of
mechanicalworking and thermal treatments, fabrication
practices,exposure to particular environments, etc., cause
significantchanges in the mechanical properties,
microstructure,resistance to brittle fracture, etc., it is of prime
importanceto call attention to those conditions that should be
avoidedin service or in manufacture of parts or vessels using
theconsumable.
Requests for Additional Data. The Committee mayrequest
additional data, including data on properties ordeposited metal
behavior not explicitly treated in the con-struction Code in which
adoption is desired.
Code Case. The Code Committee will consider the issu-ance of an
ASME Code Case, to be effective for a periodof three years,
permitting the treatment of a new weldingor brazing material under
an existing ASME Section IXgrouping for qualification purposes,
provided that the fol-lowing conditions are met:
(a) The inquirer provides evidence that a request forcoverage of
the consumable in a specification has beenmade to the AWS or a
recognized national or internationalorganization;
(b) the consumable is commercially available and canbe purchased
within the proposed specification require-ments;
(c) the inquirer shows that there will be a reasonabledemand for
the consumable by industry and that thereexists an urgency for
approval by means of a Code Case;
(d) the request for approval of the consumable shallclearly
describe it in specification form, including applica-ble items as
scope, process, manufacture, conditions fordelivery, heat
treatment, chemical and tensile requirements,testing specifications
and requirements, workmanship, fin-ish, marking, inspection, and
rejection;
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
-
www.bzfxw.com
(e) all other requirements identified previously underCode
Policy and Application apply; and
(f) the inquirer shall furnish the Code Committee withall the
data specified in this Guideline.
Requirements for Requests for ASME Acceptance ofWelding and
Brazing Material Specifications to Recog-nized National or
International Standards Other Thanthe AWS. The Committee will
consider only requests inaccordance with the Boiler and Pressure
Vessel CommitteeOperating and Administrative Procedures, OP-8.6
(Englishlanguage: U.S. or SI/metric units). The Committee
willconsider accepting specifications of recognized national
orinternational organizations in accordance with OP-8.6 suchas, but
not limited to, AWS, CSA, CEN, DIN, and JIS.Consumable
specifications of other than national or interna-tional
organizations, such as those of consumable produc-ers and
suppliers, will not be considered for acceptance.
Requirements for Recognized National or Interna-tional
Specifications. Acceptable consumable specifica-tions will be
identified by date or edition. Approvededition(s) will be stated in
the subtitle of the ASME speci-fication. Minimum requirements that
must be contained ina consumable specification for which acceptance
is beingrequested include such items as name of national or
interna-tional organization, scope, reference documents,
process,manufacture, conditions for delivery, heat treatment,
chem-ical and tensile requirements, testing specifications
andrequirements, workmanship, finish, marking, inspection,and
rejection.
Publication of Recognized National or
InternationalSpecifications. Specifications for which ASME has
notbeen given permission to publish by the originating
organi-zation will be referenced on a cover sheet in
appropriateAppendices in Section II, Part C, along with
information
xxvi
on where to obtain a copy of those documents. Documentsthat are
referenced in non-AWS consumable specificationswill not be
published by ASME. However, information onwhere to obtain a copy of
those documents will be main-tained in Section II, Part C.
Additions and exceptions tothe consumable specification will be
noted in the subtitleof the specification.
New Welding and Brazing Materials Checklist. Toassist inquirers
desiring Code coverage for new consum-ables, or extending coverage
of existing consumables, theCommittee has developed the following
checklist of itemsthat ought to be addressed by each inquiry. The
Committeereserves the right to request additional data and
applicationinformation when considering new consumables.
(a) Has a qualified inquirer request been provided?(b) Has a
request for either revision to existing Code
requirements or for a Code Case been defined?(c) Has a letter to
the AWS been submitted requesting
coverage of the new consumable in a specification, andhas a copy
been submitted to the Committee? Alternatively,is this consumable
already covered by a specification issuedby a recognized national
or international organization, andhas an English language version
been provided?
(d) Has the Construction Code and Division coveragebeen
identified?
(e) Have mechanical property data been submitted (ulti-mate
tensile strength, yield strength, reduction of area, andelongation)
for each intended joining process?
(f) Have toughness considerations required by the Con-struction
Code been defined and has appropriate data beensubmitted?
(g) Have joining requirements been defined and hasprocedure
qualification test data been submitted?
(h) Has influence of fabrication practices on depositedmetal
properties been defined?
Copyright ASME International Provided by IHS under license with
ASME Licensee=Exterran Energy Loc 9-11/5967851004
Not for Resale, 07/25/2010 23:39:59 MDTNo reproduction or
networking permitted without license from IHS
--```,,````,`,,,``,,```,,,```-`-`,,`,,`,`,,`---
标准分享网 www.bzfxw.com 免费下载
-
www.bzfxw.com
SUBMITTAL OFTECHNICAL INQUIRIES TO THE BOILER
AND PRESSURE VESSEL COMMITTEE
1 INTRODUCTION
(a) This Section provides guidance to Code users forsubmitting
technical inquiries to the Committee. SeeGuideline on the Approval
of New Materials Under theASME Boiler and Pressure Vessel Code in
Section II, PartsC and D for additional requirements for requests
involvingadding new materials to the Code. Technical
inquiriesinclude requests for revisions or additions to the
Coderules, requests for Code Cases, and requests for Code
inter-pretations, as described below.
(1) Code Revisions. Code revisions are considered toaccommodate
technological developments, address admin-istrative requirements,
incorporate Code Cases, or to clarifyCode intent.
(2) Code Cases. Code Cases represent alternatives oradditions to
existing Code rules. Code Cases are writtenas a question and reply,
and are usually intended to beincorporated into the Code at a later
date. When used,Code Cases prescribe mandatory requirements in the
samesense as the text of the Code. However, users are cautionedthat
not all jurisdictions or owners automatically acceptCode Cases. The
most common applications for CodeCases are:
(a) to permit early implementation of an approvedCode revision
based on an urgent need
(b) to permit the use of a new material for Codeconstruction
(c) to gain experience with new materials or alter-native rules
prior to incorporation directly into the Code
(3) Code Interpretations. Code Interpretations pro-vide
clarification of the meaning of existing rules in theCode, and are
also presented in question and reply format.Interpretations do not
introduce new requirements. In caseswhere existing Code text does
not fully convey the meaningthat was intended, and revision of the
rules is required tosupport an interpret