SUMMARYIEEE & IEC STANDARDSSr. NoStandard
ReferenceDescriptionCost in SARPOWER SYSTEM DESIGN AND ANALYSIS1399
- 1997( Brown Book )IEEE recommended practise for Industrial &
Commercial power system analysis ( Industrial and Commercial
Facilities )2551 - 2006 ( Voilet Book )IEEE recommended practise
for Calculating Short circuit current in Industrial and Commercial
Power System ( Industrial and Commercial Facilities )3605 -
1998IEEE Guide for design of Substation rigid - bus structures (
Power Substations )500.004738 - 2006IEEE Standard for Calculating
the Current Temparature of Bare Overhead Conductors ( Power
Transmission & Distribution )5835 -1994IEEE Standard Power
cable Ampacity Table ( Insulated Conductors )6837 - 2002IEEE
Standard for qualifying permanent connections used in substation
Grounding ( Power Substations )285.007848 - 1996IEEE Standard
Procedure for the Determiantion of Ampacity , Derating of Fire
Protected cables ( Insulated Condictors )81127 - 1998IEEE guide for
the Design, construction & operation of eleectric power
substations for community acceptance and environmental
compatability (Power substations )91189 - 1996IEEE guide for
selection of Valve - Regulated Lead - Acid ( VRLA) batteries for
station Applicatios ( Energy Devolopment & Power Generation
)10IEC - 60865-1 (1993-10)Short Circuit Currents - Caculation of
Effects Part 1 - Defenitions and Calculation Methods11IEC - 60865-2
(1994-06)Short Circuit Currents - Caculation of Effects Part 2 -
Examples of Calculations12IEC - 60909-0 (2001-07)Short Circtuit
Currents in 3 Phase AC Systems Part 0 - Caculation of CurrentsPOWER
GENERATION & DISTRIBUTION SYSTEM285.0013141 - 1993 ( Red Book
)IEE recommended practise for Electric Power Distribution for Power
plants ( Industrial and Commercial Facilities )14242 - 2001 ( Buf
Book )IEE recommended practise for Protection and Coordination of
Industrial and Commercial Power Systems ( Industrial and Commercial
Facilities )15367 - 1996IEE recommended practise for determining
the Electric Power station ground potential rise and induced
voltage from a power fault ( Communications , Power System
Communications )16643 - 2004IEE Guide for Power - Line Carrier
Applications ( Power System Communications )245.0017665 - 1995IEE
Guide for generating station Grounding [ Energy Devolopment / Power
Generation ]0.0018979 - 1994IEEE guide for Substation Fire
Protection (Power substations )315.00191050 - 2004IEEE guide for
Instrumentation & Control Equipment Grounding I Generating
stations ( Energr Development & Power Generation )201185 -
1994IEEE guide for installation methods for generating station
cables ( Insulated conductors )21487 - 2000IEE recommended practise
for the protestion of wire-line communication facilities serving
electric supply locations ( Power System Communications )22524 -
2003IEE Guide to the Installation of Overhead transmission line
conductors ( Power Transmission & Distribution )345.0023951 -
1996IEEE guide to Assembly & Erection of metal Transmission
structures ( Power Transmission & Distribution )410.0024977 -
1991IEEE guide to Installation of Foundation for Transmission Line
Structures ( Power Transmission & Distribution )525.0025979 -
1994IEEE guide for Substation Fire Protection (Power substations
)315.00261050 - 2004IEEE guide for Instrumentation & Control
Equipment Grounding I Generating stations ( Energr Development
& Power Generation )271300- 1996IEEE guide for cable
connections for Gas - Insulated Substations ( Insulated conductors
)281441 - 2004IEEE guide for Inspection of Overhead Transmission
line construction ( Power Transmission & Distribution
)29C37.104 - 2002IEEE guide for automatic reclosing of line circuit
breakers for AC distribution and Transmission Lines ( Protective
Relaying )415.0030C37.113 - 1999IEEE guide for protective Relay
Applications to Transmission Lines ( Protective Relaying
)400.0031C37.114 - 2004IEEE guide for Determining Fault Location on
AC Transmission and Dstribution Lines ( Protective Relaying
)245.00EQUIPMENTS3,215.0032484 - 2002IEE recommended practise for
Installation Design and Installation of Vented Lead Acid Batteries
for Stationary Applications [ Energy Devolopment / Power Generation
Nuclear Engineering ]33485 - 1997IEE recommended practise for
sizing Lead Acid Batteries for Stationary applications [ Energy
Devolopment / Power Generation Nuclear Engineering ]POWER SYSTEM
PROTECTION0.0034C37 - 91 - 2000IEEE guide for protective Relay
Application to Power Transformers ( Protective Relaying
)385.0035C37.96 - 2000IEEE guide for AC Motor Protection (
Protective Relaying )36C37.97 - 1979IEEE guide for protective Relay
Application to Power System Buses ( Protective Relaying
)315.0037C37.101 - 1993IEEE guide for Generator Ground Protection (
Protective Relaying )435.0038C37.102 - 2006IEEE guide for AC
Generator Protection ( Protective Relaying )39C37.106 - 2003IEEE
guide for Abnormal Frequency Protection for power generating plants
( Protective Relaying )285.00GIS1,420.0040C37.122 - 1993IEEE
standard for Gas Insulated Substations ( Power Substations
)570.0041C37.123 - 1996IEEE guide to specifications for gas -
insulated , electric power substation equipment ( Power Substations
)400.00TESTING970.00424 - 1995IEE Standard Techniques for High
Voltage Testing ( Testing , Instrumentation & Measurement, and
Metric Practise )434a - 2001Amendment to IEE Standard Techniques
for High Voltage Testing ( Testing , Instrumentation &
Measurement, and Metric Practise )4443 - 2000IEE recommended
practise for Testing Insulation Resistance of rotating machinery (
Electric Machinery )4548 - 1996IEE Standard Test Procedures and
requirements for Alternating Current cable terminations 2.5 KV
through 756 KV [Insulated conductors]4662 - 1995IEE Guide for
diagnostic field testing of electric power apparatus . Part 1 : Oil
filled Power Transformers, Regulators and Reactors [ Power
Transformers (Distribution & Regulating) Testing ,
Instrumentation & Measurement, and Metric Practise ]4781 -
1983IEE Guide for measuring earth resistivity , ground impedance
and earth surface potentials of Grounding system ( Testing ,
Instrumentation & Measurement, and Metric Practise )4882 -
2002IEE Standard Test Procedure for Impulse Voltage Test on
insulated conductors49450 - 2002IEE recommended practise for
maintanance , Testing and replacement of Vented Lead Acid Batteries
for Stationary Applications [ Energy Devolopment / Power Generation
]50576 - 2000IEE recommended practise for installatiion ,
termination & testing ofInsulated Power cables as used in
Industrial and Commercial Power System ( Industrial and Commercial
Facilities )51691 - 2001IEE Guide for Transmission Structure
Foundation Design and Testing ( Power Transmission &
Distribution )345.00521125 - 1993IEEE guide for moisture
measurement and control in SF / sub 6/Gas- Insulated
Equipment531291 - 1993IEEE guide for partial discharge measurement
in power switchgear ( Power Switchgear , Circuits & Fuses
)54C37.34 - 1994IEEE std test code for high - voltage Air Switches
( Power Switchgear , Circuits & Fuses )55C37.103 - 2004IEEE
guide for Differential & Polarising Relay curcuit Testing (
Protective Relaying )340.0056C57.12.91 - 2001IEEE std test code for
dry - type distribution & power transformers [ Power
Transformers ( Distribution & Regulating ) ]57C57.19.00 -
2004IEEE Standard General Requirement & Test Procedure for
Power apparatus Bushings [ Power Transformers ( Distribution &
Regulating ) ]58C57.113 - 1991IEEE guide for partial Discharge
measurement in Liquid - filled Power Transformers and shunt
reactors ( Power Switchgear , Circuits & Fuses )59C135.61 -
1997IEEE Standard for the testing of Overhead Transmission &
Distribution line Hardware ( Power Transmission & Distribution
)370.00POWER TRANSMISSION SYSTEM1,055.0060487 - 2000IEE recommended
practise for the protestion of wire-line communication facilities
serving electric supply locations ( Power System Communications
)61524 - 2003IEE Guide to the Installation of Overhead transmission
line conductors ( Power Transmission & Distribution
)345.0062951 - 1996IEEE guide to Assembly & Erection of metal
Transmission structures ( Power Transmission & Distribution
)410.0063977 - 1991IEEE guide to Installation of Foundation for
Transmission Line Structures ( Power Transmission &
Distribution )525.0064979 - 1994IEEE guide for Substation Fire
Protection (Power substations )315.00651050 - 2004IEEE guide for
Instrumentation & Control Equipment Grounding I Generating
stations ( Energr Development & Power Generation )661300-
1996IEEE guide for cable connections for Gas - Insulated
Substations ( Insulated conductors )671441 - 2004IEEE guide for
Inspection of Overhead Transmission line construction ( Power
Transmission & Distribution )68C37.104 - 2002IEEE guide for
automatic reclosing of line circuit breakers for AC distribution
and Transmission Lines ( Protective Relaying )415.0069C37.113 -
1999IEEE guide for protective Relay Applications to Transmission
Lines ( Protective Relaying )400.0070C37.114 - 2004IEEE guide for
Determining Fault Location on AC Transmission and Dstribution Lines
( Protective Relaying )245.0071IEC - 60050-466International
Electrotechnical Vocabulary - Overhead lines72IEC - 60652
(2002-06)Loading Tests on Overhead line structures73IEC - 60826
(2003-10)Design Criteria for Overhead Transmission line74IEC -
61773-2 (1996-11)Overhead Lines - Testing of Foundation for
Structures75C37.114 - 2004IEEE guide for Determining Fault Location
on AC Transmission and Dstribution Lines ( Protective Relaying
)245.00Total of the available costs6,945.00ESTIMATED TOTAL
COST20,000.00
&R&P of &N
Sheet1IEEE STANDARDShttp://eeexplore.ieee.orgSr. NoStandard
ReferenceDescriptionCost in SARRemarks14 - 1995IEE Standard
Techniques for High Voltage Testing ( Testing , Instrumentation
& Measurement, and Metric Practise )Testing24a - 2001Amendment
to IEE Standard Techniques for High Voltage Testing ( Testing ,
Instrumentation & Measurement, and Metric Practise )Testing343
- 2000IEE recommended practise for Testing Insulation Resistance of
rotating machinery ( Electric Machinery )Testing448 - 1996IEE
Standard Test Procedures and requirements for Alternating Current
cable terminations 2.5 KV through 756 KV [Insulated
conductors]Testing562 - 1995IEE Guide for diagnostic field testing
of electric power apparatus . Part 1 : Oil filled Power
Transformers, Regulators and Reactors [ Power Transformers
(Distribution & Regulating) Testing , Instrumentation &
Measurement, and Metric Practise ]Testing681 - 1983IEE Guide for
measuring earth resistivity , ground impedance and earth surface
potentials of Grounding system ( Testing , Instrumentation &
Measurement, and Metric Practise )Testing782 - 2002IEE Standard
Test Procedure for Impulse Voltage Test on insulated
conductorsTesting8141 - 1993 ( Red Book )IEE recommended practise
for Electric Power Distribution for Power plants ( Industrial and
Commercial Facilities )Power Gen. & Dist. System9242 - 2001 (
Buf Book )IEE recommended practise for Protection and Coordination
of Industrial and Commercial Power Systems ( Industrial and
Commercial Facilities )Power Gen. & Dist. System10367 - 1996IEE
recommended practise for determining the Electric Power station
ground potential rise and induced voltage from a power fault (
Communications , Power System Communications )Power Gen. &
Dist. System11386 - 2006IEE Standard for Seperable Insulated
connected system for Power Distribution Systems Above 600 V (
Insulated conductors Power Transmission & Distribution )12399 -
1997( Brown Book )IEE recommended practise for Industrial &
Commercial power system analysis ( Industrial and Commercial
Facilities )Power System Analysis13400.3 - 2006IEE Guide for
Partial Discharge testing of Shielded power cable Systems in a
field Environment ( Insulated Conductors Nuclear Engineering )14450
- 2002IEE recommended practise for maintanance , Testing and
replacement of Vented Lead Acid Batteries for Stationary
Applications [ Energy Devolopment / Power Generation ]Testing15484
- 2002IEE recommended practise for Installation Design and
Installation of Vented Lead Acid Batteries for Stationary
Applications [ Energy Devolopment / Power Generation Nuclear
Engineering ]Equipments16485 - 1997IEE recommended practise for
sizing Lead Acid Batteries for Stationary applications [ Energy
Devolopment / Power Generation Nuclear Engineering ]Equipments17487
- 2000IEE recommended practise for the protestion of wire-line
communication facilities serving electric supply locations ( Power
System Communications )Power Transmission system18524 - 2003IEE
Guide to the Installation of Overhead transmission line conductors
( Power Transmission & Distribution )345.00Power Transmission
system19551 - 2006 ( Voilet Book )IEE recommended practise for
Calculating Short circuit current in Industrial and Commercial
Power System ( Industrial and Commercial Facilities )Design20576 -
2000IEE recommended practise for installatiion , termination &
testing ofInsulated Power cables as used in Industrial and
Commercial Power System ( Industrial and Commercial Facilities
)Testing21605 - 1998IEE Guide for design of Substation rigid - bus
structures ( Power Substations )500.00Design22637 - 1985IEE Guide
for the reclamation of Insulating Oil and criteria of it's use [
Power Transformers (Distribution & Regulating) ]Equipments23643
- 2004IEE Guide for Power - Line Carrier Applications ( Power
System Communications )245.00Power Gen. & Dist. System24665 -
1995IEE Guide for generating station Grounding [ Energy Devolopment
/ Power Generation ]Power Gen. & Dist. System25691 - 2001IEE
Guide for Transmission Structure Foundation Design and Testing (
Power Transmission & Distribution )345.00Testing26738 - 2006IEE
Standard for Calculating the Current Temparature of Bare Overhead
Conductors ( Power Transmission & Distribution )Design27835
-1994IEEE Standard Power cable Ampacity Table ( Insulated
Conductors )Design28837 - 2002IEEE Standard for qualifying
permanent connections used in substation Grounding ( Power
Substations )285.00Design29848 - 1996IEEE Standard Procedure for
the Determiantion of Ampacity , Derating of Fire Protected cables (
Insulated Condictors )Design30951 - 1996IEEE guide to Assembly
& Erection of metal Transmission structures ( Power
Transmission & Distribution )410.00Power Transmission
system31977 - 1991IEEE guide to Installation of Foundation for
Transmission Line Structures ( Power Transmission &
Distribution )525.00Power Transmission system32979 - 1994IEEE guide
for Substation Fire Protection (Power substations )315.00Power Gen.
& Dist. System331050 - 2004IEEE guide for Instrumentation &
Control Equipment Grounding I Generating stations ( Energr
Development & Power Generation )Power Gen. & Dist.
System341125 - 1993IEEE guide for moisture measurement and control
in SF / sub 6/Gas- Insulated EquipmentTesting351127 - 1998IEEE
guide for the Design, construction & operation of eleectric
power substations for community acceptance and environmental
compatability (Power substations )Design361185 - 1994IEEE guide for
installation methods for generating station cables ( Insulated
conductors )Power Gen. & Dist. System371189 - 1996IEEE guide
for selection of Valve - Regulated Lead - Acid ( VRLA) batteries
for station Applicatios ( Energy Devolopment & Power Generation
)Design381291 - 1993IEEE guide for partial discharge measurement in
power switchgear ( Power Switchgear , Circuits & Fuses
)Testing391300- 1996IEEE guide for cable connections for Gas -
Insulated Substations ( Insulated conductors )Power Transmission
system401441 - 2004IEEE guide for Inspection of Overhead
Transmission line construction ( Power Transmission &
Distribution )Power Transmission system41C2 - 2007National Electric
Safety Code 2007 Edition [ National Electric Safety Code ( NESC )
]e42C37 - 91 - 2000IEEE guide for protective Relay Application to
Power Transformers ( Protective Relaying )385.00Protection43C37.34
- 1994IEEE std test code for high - voltage Air Switches ( Power
Switchgear , Circuits & Fuses )Testing44C37.96 - 2000IEEE guide
for AC Motor Protection ( Protective Relaying )Protection45C37.97 -
1979IEEE guide for protective Relay Application to Power System
Buses ( Protective Relaying )315.00Protection46C37.101 - 1993IEEE
guide for Generator Ground Protection ( Protective Relaying
)435.00Protection47C37.102 - 2006IEEE guide for AC Generator
Protection ( Protective Relaying )Protection48C37.103 - 2004IEEE
guide for Differential & Polarising Relay curcuit Testing (
Protective Relaying )340.00Testing49C37.104 - 2002IEEE guide for
automatic reclosing of line circuit breakers for AC distribution
and Transmission Lines ( Protective Relaying )415.00Power
Transmission system50C37.106 - 2003IEEE guide for Abnormal
Frequency Protection for power generating plants ( Protective
Relaying )285.00Protection51C37.110 - 1996IEEE guide for the
Application of Current Transformer used for Protective Relaying
Purposes ( Protective Relaying )435.0052C37.112 - 1996IEEE standard
inverse - time charcteristics equations for over current relays (
Protective Relaying )375.0053C37.113 - 1999IEEE guide for
protective Relay Applications to Transmission Lines ( Protective
Relaying )400.00Power Transmission system54C37.114 - 2004IEEE guide
for Determining Fault Location on AC Transmission and Dstribution
Lines ( Protective Relaying )245.00Power Transmission
system55C37.122 - 1993IEEE standard for Gas Insulated Substations (
Power Substations )570.00GIS56C37.123 - 1996IEEE guide to
specifications for gas - insulated , electric power substation
equipment ( Power Substations )400.00GIS57C57.12.91 - 2001IEEE std
test code for dry - type distribution & power transformers [
Power Transformers ( Distribution & Regulating )
]Testing58C57.13 - 1993IEEE std requirements for instrument
transformers [ Power Transformers ( Distribution & Regulating )
]59C57.19.00 - 2004IEEE Standard General Requirement & Test
Procedure for Power apparatus Bushings [ Power Transformers (
Distribution & Regulating ) ]Testing60C57.93 - 1995IEEE guide
for Installation of Liquid Immersed Power Transformers [ Power
Transformers ( Distribution & Regulating ) ]61C57.113 -
1991IEEE guide for partial Discharge measurement in Liquid - filled
Power Transformers and shunt reactors ( Power Switchgear , Circuits
& Fuses )Testing62C135.61 - 1997IEEE Standard for the testing
of Overhead Transmission & Distribution line Hardware ( Power
Transmission & Distribution )370.00TestingTotal7,940.00
&R&P of &Nhttp://eeexplore.ieee.org
TestingIEEE STANDARDShttp://eeexplore.ieee.orgSr. NoStandard
ReferenceDescriptionCost in SARRemarks14 - 1995IEE Standard
Techniques for High Voltage Testing ( Testing , Instrumentation
& Measurement, and Metric Practise )Testing24a - 2001Amendment
to IEE Standard Techniques for High Voltage Testing ( Testing ,
Instrumentation & Measurement, and Metric Practise )Testing343
- 2000IEE recommended practise for Testing Insulation Resistance of
rotating machinery ( Electric Machinery )Testing448 - 1996IEE
Standard Test Procedures and requirements for Alternating Current
cable terminations 2.5 KV through 756 KV [Insulated
conductors]Testing562 - 1995IEE Guide for diagnostic field testing
of electric power apparatus . Part 1 : Oil filled Power
Transformers, Regulators and Reactors [ Power Transformers
(Distribution & Regulating) Testing , Instrumentation &
Measurement, and Metric Practise ]Testing681 - 1983IEE Guide for
measuring earth resistivity , ground impedance and earth surface
potentials of Grounding system ( Testing , Instrumentation &
Measurement, and Metric Practise )Testing782 - 2002IEE Standard
Test Procedure for Impulse Voltage Test on insulated
conductorsTesting14450 - 2002IEE recommended practise for
maintanance , Testing and replacement of Vented Lead Acid Batteries
for Stationary Applications [ Energy Devolopment / Power Generation
]Testing20576 - 2000IEE recommended practise for installatiion ,
termination & testing ofInsulated Power cables as used in
Industrial and Commercial Power System ( Industrial and Commercial
Facilities )Testing25691 - 2001IEE Guide for Transmission Structure
Foundation Design and Testing ( Power Transmission &
Distribution )345.00Testing341125 - 1993IEEE guide for moisture
measurement and control in SF / sub 6/Gas- Insulated
EquipmentTesting381291 - 1993IEEE guide for partial discharge
measurement in power switchgear ( Power Switchgear , Circuits &
Fuses )Testing43C37.34 - 1994IEEE std test code for high - voltage
Air Switches ( Power Switchgear , Circuits & Fuses
)Testing48C37.103 - 2004IEEE guide for Differential &
Polarising Relay curcuit Testing ( Protective Relaying
)340.00Testing57C57.12.91 - 2001IEEE std test code for dry - type
distribution & power transformers [ Power Transformers (
Distribution & Regulating ) ]Testing58C57.13 - 1993IEEE std
requirements for instrument transformers [ Power Transformers (
Distribution & Regulating ) ]59C57.19.00 - 2004IEEE Standard
General Requirement & Test Procedure for Power apparatus
Bushings [ Power Transformers ( Distribution & Regulating )
]Testing60C57.93 - 1995IEEE guide for Installation of Liquid
Immersed Power Transformers [ Power Transformers ( Distribution
& Regulating ) ]61C57.113 - 1991IEEE guide for partial
Discharge measurement in Liquid - filled Power Transformers and
shunt reactors ( Power Switchgear , Circuits & Fuses
)Testing62C135.61 - 1997IEEE Standard for the testing of Overhead
Transmission & Distribution line Hardware ( Power Transmission
& Distribution )370.00TestingTotal1,055.00
http://eeexplore.ieee.org
Power Gen & DistIEEE STANDARDShttp://eeexplore.ieee.orgSr.
NoStandard ReferenceDescriptionCost in SARRemarks8141 - 1993 ( Red
Book )IEE recommended practise for Electric Power Distribution for
Power plants ( Industrial and Commercial Facilities )Power Gen.
& Dist. System9242 - 2001 ( Buf Book )IEE recommended practise
for Protection and Coordination of Industrial and Commercial Power
Systems ( Industrial and Commercial Facilities )Power Gen. &
Dist. System10367 - 1996IEE recommended practise for determining
the Electric Power station ground potential rise and induced
voltage from a power fault ( Communications , Power System
Communications )Power Gen. & Dist. System23643 - 2004IEE Guide
for Power - Line Carrier Applications ( Power System Communications
)245.00Power Gen. & Dist. System24665 - 1995IEE Guide for
generating station Grounding [ Energy Devolopment / Power
Generation ]Power Gen. & Dist. System32979 - 1994IEEE guide for
Substation Fire Protection (Power substations )315.00Power Gen.
& Dist. System331050 - 2004IEEE guide for Instrumentation &
Control Equipment Grounding I Generating stations ( Energr
Development & Power Generation )Power Gen. & Dist.
System361185 - 1994IEEE guide for installation methods for
generating station cables ( Insulated conductors )Power Gen. &
Dist. SystemTotal560.00
http://eeexplore.ieee.org
PS AnalysisIEEE STANDARDShttp://eeexplore.ieee.orgSr. NoStandard
ReferenceDescriptionCost in SARRemarks12399 - 1997( Brown Book )IEE
recommended practise for Industrial & Commercial power system
analysis ( Industrial and Commercial Facilities )Power System
Analysis
http://eeexplore.ieee.org
EquipmentsIEEE STANDARDShttp://eeexplore.ieee.orgSr. NoStandard
ReferenceDescriptionCost in SARRemarks15484 - 2002IEE recommended
practise for Installation Design and Installation of Vented Lead
Acid Batteries for Stationary Applications [ Energy Devolopment /
Power Generation Nuclear Engineering ]Equipments16485 - 1997IEE
recommended practise for sizing Lead Acid Batteries for Stationary
applications [ Energy Devolopment / Power Generation Nuclear
Engineering ]EquipmentsTotal0.00
http://eeexplore.ieee.org
Power TransmissionIEEE STANDARDShttp://eeexplore.ieee.orgSr.
NoStandard ReferenceDescriptionCost in SARRemarks17487 - 2000IEE
recommended practise for the protestion of wire-line communication
facilities serving electric supply locations ( Power System
Communications )Power Transmission system18524 - 2003IEE Guide to
the Installation of Overhead transmission line conductors ( Power
Transmission & Distribution )345.00Power Transmission
system30951 - 1996IEEE guide to Assembly & Erection of metal
Transmission structures ( Power Transmission & Distribution
)410.00Power Transmission system31977 - 1991IEEE guide to
Installation of Foundation for Transmission Line Structures ( Power
Transmission & Distribution )525.00Power Transmission
system32979 - 1994IEEE guide for Substation Fire Protection (Power
substations )315.00Power Gen. & Dist. System331050 - 2004IEEE
guide for Instrumentation & Control Equipment Grounding I
Generating stations ( Energr Development & Power Generation
)Power Gen. & Dist. System391300- 1996IEEE guide for cable
connections for Gas - Insulated Substations ( Insulated conductors
)Power Transmission system401441 - 2004IEEE guide for Inspection of
Overhead Transmission line construction ( Power Transmission &
Distribution )Power Transmission system49C37.104 - 2002IEEE guide
for automatic reclosing of line circuit breakers for AC
distribution and Transmission Lines ( Protective Relaying
)415.00Power Transmission system53C37.113 - 1999IEEE guide for
protective Relay Applications to Transmission Lines ( Protective
Relaying )400.00Power Transmission system54C37.114 - 2004IEEE guide
for Determining Fault Location on AC Transmission and Dstribution
Lines ( Protective Relaying )245.00Power Transmission
systemTotal2,655.00
http://eeexplore.ieee.org
DesignIEEE STANDARDShttp://eeexplore.ieee.orgSr. NoStandard
ReferenceDescriptionCost in SARRemarks19551 - 2006 ( Voilet Book
)IEE recommended practise for Calculating Short circuit current in
Industrial and Commercial Power System ( Industrial and Commercial
Facilities )Design21605 - 1998IEE Guide for design of Substation
rigid - bus structures ( Power Substations )500.00Design26738 -
2006IEE Standard for Calculating the Current Temparature of Bare
Overhead Conductors ( Power Transmission & Distribution
)Design27835 -1994IEEE Standard Power cable Ampacity Table (
Insulated Conductors )Design28837 - 2002IEEE Standard for
qualifying permanent connections used in substation Grounding (
Power Substations )285.00Design29848 - 1996IEEE Standard Procedure
for the Determiantion of Ampacity , Derating of Fire Protected
cables ( Insulated Condictors )Design351127 - 1998IEEE guide for
the Design, construction & operation of eleectric power
substations for community acceptance and environmental
compatability (Power substations )Design371189 - 1996IEEE guide for
selection of Valve - Regulated Lead - Acid ( VRLA) batteries for
station Applicatios ( Energy Devolopment & Power Generation
)DesignTotal785.00
http://eeexplore.ieee.org
Protection & GISIEEE STANDARDShttp://eeexplore.ieee.orgSr.
NoStandard ReferenceDescriptionCost in SARRemarks42C37 - 91 -
2000IEEE guide for protective Relay Application to Power
Transformers ( Protective Relaying )385.00Protection44C37.96 -
2000IEEE guide for AC Motor Protection ( Protective Relaying
)Protection45C37.97 - 1979IEEE guide for protective Relay
Application to Power System Buses ( Protective Relaying
)315.00Protection46C37.101 - 1993IEEE guide for Generator Ground
Protection ( Protective Relaying )435.00Protection47C37.102 -
2006IEEE guide for AC Generator Protection ( Protective Relaying
)Protection50C37.106 - 2003IEEE guide for Abnormal Frequency
Protection for power generating plants ( Protective Relaying
)285.00Protection55C37.122 - 1993IEEE standard for Gas Insulated
Substations ( Power Substations )570.00GIS56C37.123 - 1996IEEE
guide to specifications for gas - insulated , electric power
substation equipment ( Power Substations
)400.00GISTotal2,390.00
http://eeexplore.ieee.org
Sheet2IEC STANDARDSSr. NoStandard
ReferenceDescriptionCostRemarks1IEC - 60050-466International
Electrotechnical Vocabulary - Overhead lines2IEC - 60652
(2002-06)Loading Tests on Overhead line structures3IEC - 60826
(2003-10)Design Criteria for Overhead Transmission line4IEC -
61773-2 (1996-11)Overhead Lines - Testing of Foundation for
Structures5IEC - 60865-1 (1993-10)Short Circuit Currents -
Caculation of Effects Part 1 - Defenitions and Calculation
Methods6IEC - 60865-2 (1994-06)Short Circuit Currents - Caculation
of Effects Part 2 - Examples of Calculations7IEC - 60909-0
(2001-07)Short Circtuit Currents in 3 Phase AC Systems Part 0 -
Caculation of Currents89101112131415161718192021222324