IEC LAB ASSIGNMENT-1 NAME:MADHUKAR AGARWAL ENTRY NO-2011EEN2477 Question-1: For minimum length =.18micron and width=.24 micron of NMOS ,the graph of log10(i) vs VDS for NMOS is shown at values of VDS=0.5, 1 ,1.5 and 1.8. 3333 Question-2: 1) Boundary point between the exponential and quadratic regions for NMOS At the boundary point of exponential and quadratic regions we have VGS=Vt(threshold voltage) and the corresponding value of drain current Id=Id(st).These points are clearly depicted on the graph.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
IEC LAB ASSIGNMENT-1
NAME:MADHUKAR AGARWAL
ENTRY NO-2011EEN2477
Question-1:
For minimum length =.18micron and width=.24 micron of NMOS ,the graph of log10(i) vs VDS for NMOS is shown at values of VDS=0.5, 1 ,1.5 and 1.8.
3333
Question-2:
1) Boundary point between the exponential and quadratic regions for NMOS At the boundary point of exponential and quadratic regions we have VGS=Vt(threshold voltage) and the corresponding value of drain current Id=Id(st).These points are clearly depicted on the graph.
Question-2: Slope of curve in the exponential region
We find that slope in units of volts/decade is equal to .089498(approx).
Question-2: Finding n- factor
S=n(KT/q)ln(10)
Here the slope is measured in mV/decade. For an ideal transistor (KT/q)ln(10) equals to 60 mV/decade. By Using this formula
We find that the approximate value of n-factor =1.5
Question-2: Plot of Vt vs VDS BY using MATLAB tool
Question-2: Identifying the boundary between the linear and quadratic regions
Boundary point between the regions(linear,exponential and quadratic) can be easily identified by the plot of derivative of drain current (Id) versus VGS for different values of VDS=0.5,1.0,1.5 and 1.8.Boundary points are shown in the figure below.
TABULATION OF VOLTAGE RANGES FOR DIFFERENT OPERATIONS OF NMOS
LINEAR REGION VDS VGS 1.8V 1.284-1.8V 1.5V 1.164-1.8V 1.0V .9508-1.8V 0.5V .7995-1.8V
For minimum length =.18micron and width=.24 micron of PMOS ,the graph of log10(i) vs VDS for PMOS is shown at values of VDS=0.5, 1 ,1.5 and 1.8.
Question-2:
1) Boundary point between the exponential and quadratic regions for PMOS At the boundary point of exponential and quadratic regions we have VGS=Vt(threshold voltage) and the corresponding value of drain current Id=Id(st).These points are clearly depicted on the graph.
Question-2: Slope of curve in the exponential region
We find that slope in units of volts/decade is equal to .09730(approx).
Question-2: Finding n- factor
S=n(KT/q)ln(10)
Here the slope is measured in mV/decade. For an ideal transistor (KT/q) ln(10) equals to 60 mV/decade. By Using this formula
We find that the approximate value of n-factor =1.62.
Question-2: Plot of Vt vs VDS BY using MATLAB tool
Question-2: Identifying the boundary between the linear and quadratic regions
Boundary point between the regions(linear,exponential and quadratic) can be easily identified by the plot of derivative of drain current (Id) versus VGS for different values of VDS=0.5,1.0,1.5 and 1.8.Boundary points are shown in the figure below.
TABULATION OF VOLTAGE RANGES FOR DIFFERENT OPERATIONS OF PMOS
LINEAR REGION VDS VGS 1.8V 1.42-1.8V 1.5V 1.297-1.8V 1.0V 1.143-1.8V 0.5V 1.0-1.8V
Now computing capacitance of oxide per unit area=3.9*8.85*10^-12/4.2*10^-9
Now computing the value of CGCS in all the three regions
In cutoff mode CGCS=0
In resistive mode CGCS= capacitance of oxide per unit area*W*L/2
In saturation mode CGCS=(2/3) *capacitance of oxide per unit area*W*L
Now computing the value of CGCD in all the three regions
In cutoff mode CGCD=0
In resistive mode CGCD= capacitance of oxide per unit area*W*L/2
In saturation mode CGCD=0
Now we can easily comput the value of capacitances CGS and CGD as follows:
CGS=CGCS + CGS0
CGD=CGCD + CGD0
Region of Operation CGS CGD Cut-off 0.564 x 10^-16 0.564 x 10^-16 Resistive 0.2334 x 10^-15 0.2334 x 10^-15 Saturation 0.2924 x 10^-15 0.564 x 10^-16
Question-5: Plot of Cg vs VGS charachtersticks for NMOS
Taking current source at gate = .1 mili ampere and the voltage at the gate terminal to be -3 volts,
So for the given test method and circuit the plot of VGS versus time (transient response) and also the plot of Cg versus VGS Charachtersticks will look like as shown in the figure.
Question-5: Plot of Cg vs VGD charachtersticks for PMOS
Taking current source at gate = .1 mili ampere and the voltage at the gate terminal to be -3 volts,
So for the given test method and circuit the plot of VGD versus time (transient response) and also the plot of Cg versus VGD Charachtersticks will look like as shown in the figure.
Question-5: Plot of Cd vs VDS charachtersticks for NMOS
In order to find out the value of aCd, taking the help of test method so for VGS=0 and by applying a current source between drain and source. Taking current source at drain = .1 mili ampere and the voltage at the drain terminal to be -3 volts,
So for the given test method and circuit the plot of VDS versus time (transient response) and also the plot of Cd versus VDS Charachtersticks will look like as shown in the figure.
Question-5: Plot of Cs vs VSD charachtersticks for PMOS
In order to find out the value of Cs, taking the help of test method so for VGD=0 and by applying a current source between drain and source. Taking current source at source terminal = .1 mili ampere and the voltage at the source terminal to be -3 volts,
So for the given test method and circuit the plot of VSD versus time (transient response) and also the plot of Cs versus VSD Charachtersticks will look like as shown in the figure.