I TEC TRAINING This training session will explain how to use ITEC equipment and support learning in the classroom setting. Presented by: R. Schmid.

ITEC TRAINING

This training session will explain how to use ITEC equipment and support learning in the classroom setting.

Presented by: R. Schmid

TABLE OF CONTENTS

1. LCD Projector2. Select audio/video source3. Power Screen4. Volume Control5. Picture Mute6. DVD/VCR Control Panel7. Document Camera8. Laptop setup9. Touch Screen Panel10. OIT Help Desk

The intended use of this tutorial is to help you learn how to use all of the ITEC Equipment on SJFC campus.

STEP 1: TURN ON LCD PROJECTOR From the control panel, within the Display Section, press the ON or OFF

button.

Button will flash while it is warming up or cooling down.

Flashing stops, LCD projector is ready for use—select a source to display.

** Remember to turn off the projector when finished using**

STEP 3: POWERED PROJECTION SCREEN

In classrooms with a powered projection screen, the screen control switch can be located on the wall behind the presenter’s station.

STEP 4: VOLUME CONTROL Use the volume knob on the control panel to

adjust the volume of the selected device. Troubleshooting steps….

NO SOUND ???

If using a PC or Laptop: From the task bar, click on the sound icon Ensure that Mute isn’t checked Raise or lower the volume control bar to adjust the

sound

WHAT IS PICTURE MUTE?

To mute or “hide” what is being displayed through the projector.

Press the PIC MUTE button, located in the middle of the control panel.

DVD/ VCR CONTROL PANEL

After selecting DVD or VCR as your source, use this control panel just like you would a remote control.

STEP 2: DISPLAY DEVICE THROUGH LCD PROJECTOR

From the input button section, select device to be displayed.

Showing a DVD to your class, press the DVD

button

CHOOSE A MODEL Three different models on campus, click on the

picture for instructions.

STEP 1 OF 4: POWER ON

Power on, hold down button until the red light flashes.

Ready to use when the light turns green.

Step 2

Back

STEP 2 OF 4: SELECT DOC CAM AS SOURCE

From the control panel, press the DOC CAM button.

Step 3

Back

STEP 3 OF 4: FOCUS AND ZOOM Press the AF button to Auto Focus Digital Zoom press the Zoom + or – button Manual Zoom raise the camera neck to position the

camera

Back Step 4

STEP 4 OF 4: POWER OFF Hold down the Power button until the green light

flashes, light turns red when the document camera is off.

Back Choose a model

STEP 1 OF 4: POWER ON Slide the POWER button up or down. Ready to use when the light is on.

Back Step 2

STEP 2 OF 4: SELECT DOC CAM AS SOURCE

From the control panel, press the DOC CAM button.

Back Step 3

STEP 3 OF 4: ZOOM Digital Zoom sliding your finger across the zoom

wheel, you can zoom in or out.

Back Step 4

STEP 4 OF 4: POWER OFF Slide the Power button down to turn off.

Back Choose a model

STEP 1 OF 4: POWER ON Power on, hold down button until the red light

flashes. Ready to use when the light turns green.

Back Step 2

STEP 2 OF 4: SELECT DOC CAM AS SOURCE

From the control panel, press the DOC CAM button.

Back Step 3

STEP 3 OF 4: ZOOM AND BRIGHTNESS

Press the Zoom + or – button to zoom in or out. With the arm lights on, press the Brightness + or – button.

Back Step 4

STEP 4 OF 4: POWER OFF

Hold down the Power button until the green light flashes.

The document camera is off when the light turns red.

Back Choose a model

HOW DO I CONNECT A LAPTOP?

Attach the VGA and audio cables if necessary to your laptop.

Enable the Monitor Out Function on your laptop

VGA

Audio

MONITOR OUT FUNCTION On your laptop use the “Monitor Out” key in

conjunction with the Function Button (Fn). The Monitor Out key is usually labeled with a “|

|”symbol or says CRT/LCD” and is usually the F4, F5, or F8 key

TOUCH SCREEN PANEL The projector will power on once a source is selected. All

sources are located on the left of the touch screen. Note: The projector will take about 30 seconds for the

lamp to warm up. 

Sources

Volume

Help

NEED ASSISTANCE – CONTACT HELP DESK

Contact the OIT Help Desk By phone: 385-8016 –please feel free to leave a

message By e-mail: [email protected] In person: Kearney 053 (adjacent to the computer lab)

ITEC classrooms on SJFC campus- View pictures and instructions online at http://oit.sjfc.edu/Labs/lab_intro.asp