This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
CATALOG | 08312018
199-PVR Poly-V Belt DrivenLive Roller Conveyor
The Model 199-PVR is a medium-duty poly-v belt driven live roller conveyor. The roll-to-roll belt drive makes this conveyor ideal for light duty pallet handling where little maintenance or a quieter conveyor is desirable.
• 11 Bed Widths• Shaft Mounted Drive• Reversible• Poly-V Belt Driven Rollers• Adjustable MSN-Type Floor Supports Available
• All weights in catalog are conveyor weights only. Accessories, crating, etc. are not included• Motors will slave a maximum of 40 rollers, 20 rollers per side.
CATALOG | 08312018
199-PVRBED–Roller bed with 1.9 in. x 9 ga. wall unplated tread rollers spaced every 3 in, 4 in, or 6 in mounted in 7 ga. powder painted formed steel channel frame bolted together with butt couplings.
SHAFT MOUNTED DRIVE–Shaft mounted gearmotor to the side of the bed section.
POLY-V BELT–4-rib J-Profile roller to roller GUARD–Mounted to top of channel frame to totally enclose drive belts.
BEARINGS–Sealed, pre-lubricated ball bearings on drive roller shaft.
MOTOR–1/2 HP–208/230/460/575V–3 Ph. 60 Hz. Gearmotor.
CONVEYING SPEED–Constant 35 FPM.
CAPACITY–Maximum load per linear foot of conveyor 150 lbs with supports on 10’ centers, 250 lbs with supports on 5’ centers. 600 lbs total load.
FLOOR SUPPORTS–Now supplied as optional equipment.
CONVEYOR LENGTH–Maximum 10’ per drive.
• OPTIONAL EQUIPMENT
FLOOR SUPPORTS–MSN Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MSN-6 support.
CONVEYING SPEED–Other constant and variable speeds. NOTE: Capacity affected with speed change.
GUARD RAILS–Adjustable Universal Channel Guard Rail, (both sides) fixed channel (both sides) or angle (one side). See Accessory section .
POLY-TIER SUPPORTS–36 in. to 120 in. support heights in 6 in. increments. Knee braces supplied.
CEILING HANGERS–5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available.
MOTORS–Other HP gearmotors available.
ELECTRICAL CONTROLS–Non-reversing magnetic starters and push-button stations. AC variable frequency drive.
TRANSFERS–Chain transfers available. See accessories.
GUARD REMOVED TO ILLUSTRATE ROLL TO ROLL DRIVE BELT.
WARNING: DO NOT OPERATE CONVEYOR WITH GUARD REMOVED.
• STANDARD SPECIFICATIONS
CATALOG | 08312018
25-PVR Poly-V Belt Driven Live RollerConveyor (Roll-to-Roll Type)
The heavy design of the 25-PVR allows it to be used for conveying higher load capacities such as loaded pallets and drums. Poly-V belt driven rollers make it ideal for conveying heavier parts where little maintenance or a quieter conveyor is required.
• 15 Bed Widths• Shaft Mounted Drive• Reversible• Poly-V Belt Driven Rollers• Adjustable HSN-Type Floor Supports Available
• All weights in catalog are conveyor weights only. Accessories, crating, etc. are not included• Motors will slave a maximum of 40 rollers, 20 rollers per side.
Conveyor shown with optional floor
supports
VIEW A-ASCALE 1:5
OVERALL LENGTH
OVERALL LENGTH
OVERALLFRAME WIDTH
BETWEENRAIL WIDTH
CONVEYINGSURFACE
7/8
8
45
2 19/32
6 1/8
1 3/4
3/8 2 19/32
Optional HSN Supports Shown
Optional HSN Supports Shown
CATALOG | 08312018
25-PVRBED–Roller bed with 2 1/2 in. dia. x 11 ga. unplated tread rollers spaced every 3 in., 4 in., or 6 in. roller centers only. Tread rollers mounted in 4 in. x 4 ga. powder painted formed steel channel on side opposite guard and 5 in. x 4 ga. powder painted formed steel channel on guard side.
SHAFT MOUNTED DRIVE–Shaft mounted drive to the side of the bed section.
POLY-V BELT–8-rib J-Profile roller to roller.
GUARD–Formed steel, upper and lower guard mounted to top and bottom of channel frame to totally enclose drive belts.
BEARINGS–Sealed, pre-lubricated ball bearings.
MOTOR–1 HP–208/230/460/575V–3 Ph. 60 Hz. gearmotor.
CONVEYING SPEED–Constant 30 FPM.
CAPACITY–– Maximum load per linear foot of conveyor 300 lb. with supports on 10 ft. centers, 1000 lb. with supports on 5 ft. centers. Total load 3000 lbs.
FLOOR SUPPORTS–Now supplied as optional equipment.
CONVEYOR LENGTHS–Maximum 10’ per drive.
• OPTIONAL EQUIPMENTFLOOR SUPPORTS–HSN Type floor supports are available with a wide range of adjustment. Specify top or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above HSN-3 support.
CONVEYING SPEED–Other constant and variable speeds. NOTE: Capacity affected with speed change.
GUARD RAILS–Fixed angle (2 in. high x 1/4 in. steel) guard bolts to top flange of channel opposite guard.
CHANNEL END STOP–6” x 8.2 lb. structural channel end stop.
TRANSFERS–Chain transfers available. See Accessory section.
MOTORS–Other HP gearmotors available.
ELECTRICAL CONTROLS–Non-reversing magnetic starter – push-button stations. AC variable frequency drive.
• STANDARD SPECIFICATIONS
GUARD REMOVED TO ILLUSTRATE ROLL TO ROLL DRIVE BELT.
WARNING: DO NOT OPERATE CONVEYOR WITH GUARD REMOVED.
CATALOG | 08312018
199-PVEZD Medium DutyAccumulating Conveyor
(Zero Pressure Accumulating Type)The Model 199-PVEZD is a chain driven live roller conveyor designed for zero pressure accumulation of products. This conveyor is designed to handle cartons or pallets. Products may be accumulated in zones and released upon request.
• EZDriveTM System (Individual zone drive)• EZLogic® Accumulation System• Poly-V Belt Driven Rollers• Shaft Mounted Drive• Adjustable MSN-Type Floor Supports Available
Conveyor shown with optional floor
supports
HOW IT WORKSThe conveyor is made up of accumulation zones. Each zone contains an individual zone drive interfaced to Hytrol’s EZLogic® Zone Controllers, which sense product presence and control the accumulation and release of the zones by starting and stopping the zone drives.
• Total Weight = (Number of Zones x 30) + (OAL x Weight Per Foot)• All weights in catalog are conveyor weights only. Accessories, crating, etc. are not included.• Motors will slave a maximum of 40 rollers, 20 rollers per side.
DISCONNECT PANEL(SINGLE OUTPUT SHOWN)
EZDriveZONE STARTER BOX
IOPSECTION LENGTH
OVERALL LENGTH
OPTIONAL MSNSUPPORTS SHOWN
8 1/8OVERALLFRAMEWIDTH
BETWEENFRAMEWIDTH
CONVEYINGSURFACE
11 1/16
7 1/21/4
3 1/2
U.S. Patent Numbers7,243,781 • 7,591,366 7,905,345 • 6,860,381
Other Patents Pending.
CATALOG | 08312018
199-PVEZDBED–Roller bed with 1.9 in. dia. x 9 ga. unplated rollers spaced every 3, 4, or 6 in. Tread rollers mounted in 3 1/2 in. x 7 ga. formed channel on side opposite guard and 4 1/2 in. x 7 ga. formed channel on guard side. Bolted together with butt couplings.
EZDriveTM System–Shaft mounted gearmotor located near center of each zone. 1/2 HP - 3 PH 60 Hz. Totally enclosed fan cooled. 230/460 V (specify voltage). Includes EZDriveTM Disconnect Panel. Power is distributed zone to zone through pluggable cordsets. Power is connected from the starter box to the motor via “SO” type cord. Please contact factory if local code requires other than the standard power distribution techniques described.
ACCUMULATION ZONES–4 in. roller centers, 32 in. to 120 in. on 4 in. increments. 3in. and 6 in. centers, 30 in. to 120 in. on 3in. or 6 in. increments. Frame length changes with zone length.
EZLOGIC® ZONE CONTROLLER–Located in each zone (Retro-Reflective). NEMA 1, 2, IP 62. UL Approved.
IOP–Provides 27VDC, 100 watt power for EZLogic® accumulation system - contains slots for 4 input/output boards. Should be located near disconnect panel. See chart for maximum quantity of zones. Requires 120VAC or 230VAC single phase input.
CONVEYING SPEED–Constant 35 FPM.
CAPACITY–Maximum load per linear foot of conveyor 150 lbs. with supports on 10 ft. centers and 250 lbs with supports on 5 ft. centers. Maximum unit load 1000 lbs. per zone. Zones longer than 6 ft. may require an additional floor support depending on product load.
FLOOR SUPPORTS–Now supplied as optional equipment.
• OPTIONAL EQUIPMENTFLOOR SUPPORTS–MSN Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MSN-6 support.
CONVEYING SPEED–Other constant and variable speeds. Note: Capacity affected with speed change.
POLY-TIER SUPPORTS–36 in. to 120 in. support heights in 6 in. increments. Knee braces supplied.
CEILING HANGERS–5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available.
EZDriveTM System:• Variable Frequency Drive–for adjusting conveying speed or adjusting acceleration and
deceleration time.
EZLogic® – See EZLogic® Components Page.
EZLOGIC® ACCUMULATION SYSTEMHytrol’s EZLogic®, or “Electronic Zero-pressure Logic” Accumulation System, combines the sensing accuracy of photo-electronics with discrete electronic logic control without the use of a PLC or pneumatic logic components. The EZLogic® Accumulation System provides many features including:
Zero-Pressure Accumulation of Product
Zone Stop - Function is built in. Any zone may be transformed into a workstation by connecting a dry contact switching device to the auxiliary port of the EZLogic® Zone Controller. This feature is always used at the discharge end of the conveyor line, and may be used at any other location where a zone stop is required.
Dynamic Zone Allocation – Automatically adjusts the conveyor’s zone length to accommodate the length of the product being conveyed. Improves conveyor efficiency and system flexibility.
Sleep Feature – Stops tread rollers from turning when no product is present, reducing noise, reducing energy consumption and extending roller bearing life.
Unloading Zone Feature - Zone On Delay – Timer delays the zone immediately upstream from a removed load, preventing it from driving for a set time. This feature is ideal where loads are routinely removed from the conveyor with a lift truck.
Loading Zone Feature – Zone detects load being placed onto the conveyor with a fork truck and stops the zone from driving and automatically prevents any loads in zones upstream from entering loading area.
SINGLE OUTPUT DISCONNECT PANEL
DUAL OUTPUT DISCONNECT PANEL (MUST BE LOCATED AT THE CENTER OF CONVEYOR)
ZONE GEARMOTOR
ZONE GEARMOTOR
INFEED EYE EZLOGIC® ZONE CONTROLLER
INFEED EYE EZLOGIC® ZONE CONTROLLER
EZDRIVE™ ZONE STARTER BOX
EZDRIVE™ ZONE STARTER BOX
IOP
IOP
† Note: Infeed Wake-Up Eye used only on terminating infeed end of conveyor. Not used when connecting to upstream EZLogic® conveyor through power supply isolation cable.
DISCONNECTPANEL
230V 460V3 Ph. 60 Hz 3 Ph. 60 Hz
SINGLE OUTPUT 1-8 ZONES 1-15 ZONESDUAL OUTPUT 9-16 ZONES 16-22 ZONES
FLOW
FLOW
RH CHAIN GUARD
(STANDARD)
LH CHAIN GUARD
FLOW
FLOW
• STANDARD SPECIFICATIONS
CATALOG | 08312018
The Model 25-PVEZD is a Poly-V Belt driven live roller conveyor designed for zero pressure accumulation of products. This conveyor is designed to handle loads such as pallets, drums, containers, etc. Products may be accumulated in zones and released upon request.
• EZDriveTM System (Individual zone drive)• EZLogic® Accumulation System• Poly-V Belt Driven Rollers• Shaft Mounted Drive• Adjustable HSN-Type Floor Supports Available
Conveyor shown with optional floor supports25-PVEZD Heavy Duty Accumulating Conveyor
(Zero Pressure Accumulating Type)
OAW–3 in., 4 in., and 6 in. Roller Centers.Conveying
• Total Weight = (Number of Zones x 30) + (OAL x Weight per Foot)• All weights in catalog are conveyor weights only. Accessories, crating, etc. are not included.• Motors will slave a maximum of 40 rollers, 20 rollers per side.
8 1/8OVERALL
FRAMEWIDTH
BETWEENFRAMEWIDTH
CONVEYINGSURFACE
3/8
4
7 13/16
11 1/16
SECTION LENGTH
OVERALL LENGTH
DISCONNECT PANEL(SINGLE OUTPUT SHOWN)
EZDriveZONE STARTER BOX
OPTIONAL HSNSUPPORTS SHOWN
IOP
U.S. Patent Numbers7,243,781 • 7,591,366 7,905,345 • 6,860,381
Other Patents Pending.
CATALOG | 08312018
SINGLE OUTPUT DISCONNECT PANEL
DUAL OUTPUT DISCONNECT PANEL (MUST BE LOCATED AT THE CENTER OF CONVEYOR)
ZONE GEARMOTOR
ZONE GEARMOTOR
INFEED EYE EZLOGIC® ZONE CONTROLLER
INFEED EYE EZLOGIC® ZONE CONTROLLER
EZDRIVE™ ZONE STARTER BOX
EZDRIVE™ ZONE STARTER BOX
IOP
IOP
25-PVEZDBED–Roller bed with 2 1/2 in. dia. x 11 ga. unplated rollers spaced every 3, 4, or 6 in. Tread rollers mounted in 4 in. x 4 ga. formed channel on side opposite chain guard and 5 in. x 4 ga. formed channel on chain guard side. Bolted together with butt couplings.
EZDriveTM System–Shaft mounted gearmotor located near center of each zone. 1/2 HP - 3 PH 60 Hz. Totally enclosed fan cooled. 230/460 V (specify voltage). Includes EZDriveTM Disconnect Panel. Power is distributed zone to zone through pluggable cordsets. Power is connected from the starter box to the motor via “SO” type cord. Please contact factory if local code requires other than the standard power distribution techniques described.
ACCUMULATION ZONES–4 in. roller centers, 32 in. to 120 in. on 4 in. increments. 3 in. and 6 in. roller centers, 30 in. to 120 in. on 6 in. increments. Frame length changes with zone length.
EZLOGIC® ZONE CONTROLLER–Located in each zone (Retro-Reflective). NEMA 1, 2, IP 62. UL Approved.
IOP–Provides 27VDC, 100 watt power for EZLogic® accumulation system - contains slots for 4 input/output boards. Should be located near disconnect panel. See chart for maximum quantity of zones. Requires 120VAC or 230VAC single phase input.
CONVEYING SPEED–Constant 28 FPM.
CAPACITY–Maximum load per linear foot of conveyor 300 lbs. with supports on 10 ft. centers and 1000 lbs. with supports on 5 ft. centers. Maximum unit load 3000 lbs per zone. Zones longer than 6 ft. may require an additional floor support depending on product load.
FLOOR SUPPORTS–Now supplied as optional equipment.
• OPTIONAL EQUIPMENTFLOOR SUPPORTS–HSN Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above HSN-6 support.
CONVEYING SPEED–Other constant and variable speeds available, contact factory.
GUARD RAIL – Angle type only
EZDrive® System: • Variable Frequency Drive-for adjusting conveying speed or adjusting acceleration and
deceleration time.
EZLogic® – See EZLogic® Components Page.
EZLOGIC® ACCUMULATION SYSTEMHytrol’s EZLogic®, or “Electronic Zero-pressure Logic” Accumulation System, combines the sensing accuracy of photo-electronics with discrete electronic logic control without the use of a PLC or pneumatic logic components. The EZLogic® Accumulation System provides many features including:
Zero-Pressure Accumulation of Product
Zone Stop - Function is built in. Any zone may be transformed into a workstation by connecting a dry contact switching device to the auxiliary port of the EZLogic® Zone Controller. This feature is always used at the discharge end of the conveyor line, and may be used at any other location where a zone stop is required.
Dynamic Zone Allocation – Automatically adjusts the conveyor’s zone length to accommodate the length of the product being conveyed. Improves conveyor efficiency and system flexibility.
Sleep Feature – Stops tread rollers from turning when no product is present, reducing noise, reducing energy consumption and extending roller bearing life.
Unloading Zone Feature - Zone On Delay – Timer delays the zone immediately upstream from a removed load, preventing it from driving for a set time. This feature is ideal where loads are routinely removed from the conveyor with a lift truck.
Loading Zone Feature – Zone detects load being placed onto the conveyor with a fork truck and stops the zone from driving and automatically prevents any loads in zones upstream from entering loading area.
† Note: Infeed Wake-Up Eye used only on terminating infeed end of conveyor. Not used when connecting to upstream EZLogic® conveyor through power supply isolation cable.
DISCONNECTPANEL
230V 460V3 Ph. 60 Hz 3 Ph. 60 Hz
SINGLE OUTPUT 1-5 ZONES 1-10 ZONESDUAL OUTPUT 6-10 ZONES 11-20 ZONES F
LOW
RH CHAIN GUARD
(STANDARD)
LH CHAIN GUARD
FLOW
FLOW
• STANDARD SPECIFICATIONS
CATALOG | 08312018
199-PVE24EZ24 Volt DC Horizontal
Power Conveyor(Zero Pressure
Accumulating Type)The Model 199-PVE24EZ Accumulating conveyor uses a 24 VDC motor/reducer to drive Poly-V Belt driven tread rollers. This conveyor is designed to handle cartons or pallets. Products may be accumulated in zones and released upon request.
• EZLogic® Accumulation System• Poly-V Belt Driven Rollers• Shaft Mounted 24 VDC Drive• Adjustable MSN-Type Floor Supports Available
Conveyor shown with optional floor
supports
HOW IT WORKSThe conveyor is made up of accumulation zones. Each zone contains an individual zone drive interfaced to Hytrol’s EZLogic® Zone Controllers, which sense product presence and control the accumulation and release of the zones by starting and stopping the zone drives.
• Total Weight = (Number of Zones x 30) + (OAL x Weight Per Foot)• All weights in catalog are conveyor weights only. Accessories, crating, etc. are not included. • Motors will slave a maximum of 40 rollers, 20 rollers per side.
OVERALLFRAMEWIDTH
BETWEENFRAMEWIDTH
CONVEYINGSURFACE
8 1/8
11 59/64
IOPPOWERBLOCK/E24 MOTOR
40 AMP POWER SUPPLY
RETRO-REFLECTIVEACCUMULATION CHANNEL
FLOW
SECTION LENGTHSECTION LENGTHSECTION LENGTH
OVERALL LENGTH
24TMe
U.S. Patent Numbers7,243,781 • 7,591,366 7,905,345 • 6,860,381
Other Patents Pending.
CATALOG | 08312018
199-PVE24EZBED–Roller bed with 1.9 in. dia. x 9 ga. unplated rollers spaced every 3, 4, or 6 in. Tread rollers mounted in 3 1/2 in. x 7 ga. formed channel on side opposite guard and 4 1/2 in. x 7 ga. formed channel on guard side. Bolted together with butt couplings.
ACCUMULATION ZONES–4 in. roller centers, 32 in. to 120 in. on 4 in. increments. 6 in. centers, 30 in. to 120 in. on 6 in. increments. Frame length changes with zone length.
MOTOR–One 24 VDC motor in each zone.
EZLOGIC® ZONE CONTROLLER–Located in each zone (Retro-Reflective). NEMA 1, 2, IP 62. UL Approved.
POWER SUPPLY (FOR MOTORS)—40 amp DC power supply, 28 volt fixed output. Maximum of 8 zones per power supply. 120 vac, 24 amp input. Mounted near center of conveyor.
IOP—Provides 27VDC, 100 watt power for EZLogic® accumulation system - contains slots for 4 input/output boards. Operates up to 50 zones with maximum of 25 on either side of IOP. Requires 120VAC or 230VAC single phase input.
CONVEYING SPEED–Up to 35 FPM.
CAPACITY–Maximum load per linear foot of conveyor 150 lbs. supports on 10 ft. centers. 250 lbs. per ft. with supports on 5 ft. centers. Not to exceed 1000 lbs per zone. Zones longer than 6 ft. may require an additional floor support depending on product load.
FLOOR SUPPORTS–Now supplied as optional equipment.
• OPTIONAL EQUIPMENTFLOOR SUPPORTS–MSN Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MSN-6 support.
CONVEYING SPEED–Other constant and variable speeds. Note: Capacity affected with speed change.
POLY-TIER SUPPORTS–36 in. to 120 in. support heights in 6 in. increments. Knee braces supplied.
CEILING HANGERS–5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available.
EZLogic® – See EZLogic® Components Page.
EZLOGIC® ACCUMULATION SYSTEMHytrol’s EZLogic®, or “Electronic Zero-pressure Logic” Accumulation System, combines the sensing accuracy of photo-electronics with discrete electronic logic control without the use of a PLC or pneumatic logic components. The EZLogic® Accumulation System provides many features including:
Zero-Pressure Accumulation of Product
Zone Stop - Function is built in. Any zone may be transformed into a workstation by connecting a dry contact switching device to the auxiliary port of the EZLogic® Zone Controller. This feature is always used at the discharge end of the conveyor line, and may be used at any other location where a zone stop is required.
Dynamic Zone Allocation – Automatically adjusts the conveyor’s zone length to accommodate the length of the product being conveyed. Improves conveyor efficiency and system flexibility.
Sleep Feature – Stops tread rollers from turning when no product is present, reducing noise, reducing energy consumption and extending roller bearing life.
Unloading Zone Feature - Zone On Delay – Timer delays the zone immediately upstream from a removed load, preventing it from driving for a set time. This feature is ideal where loads are routinely removed from the conveyor with a lift truck.
Loading Zone Feature – Zone detects load being placed onto the conveyor with a fork truck and stops the zone from driving and automatically prevents any loads in zones upstream from entering loading area.
• STANDARD SPECIFICATIONS
† Note: Infeed Wake-Up Eye used only on terminating infeed end of conveyor. Not used when connecting to upstream EZLogic® conveyor through power supply isolation cable.
Power Supply
Max Number of Zones
20 AMP 440 AMP 8
FLOW
FLOW
RH GUARD
(STANDARD)
LH GUARD
FLOW
FLOW
IOPEZLOGIC® ZONE CONTROLLER
40 AMP POWER SUPPLY
MOTOR CONTROLLER
E24 MOTOR/POWERCUBE
INFEED EYE
CATALOG | 08312018
The Model 25-PVE24EZ Accumulating conveyor uses a 24 VDC motor/reducer to drive Poly-V Belt driven tread rollers. This conveyor is designed to handle loads such as pallets, drums, containers, etc. Products may be accumulated in zones and released upon request.
• EZLogic® Accumulation System• Poly-V Belt Driven Rollers• Shaft Mounted 24VDC Drive• Adjustable HSN-Type Floor Supports Available
Conveyor shown with optional floor supports25-PVE24EZ
24 Volt DC Horizontal Power Conveyor
(Zero Pressure Accumulating Type)
OAW–3 in., 4 in., and 6 in. Roller Centers.Conveying
• Total Weight = (Number of Zones x 30) + (OAL x Weight per Foot)• All weights in catalog are conveyor weights only. Accessories, crating, etc. are not included.• Motors will slave a maximum of 40 rollers, 20 rollers per side.
OVERALLFRAMEWIDTH
BETWEENFRAMEWIDTH
CONVEYINGSURFACE
17/32
8 1/8
12
IOPPOWERBLOCK/E24 MOTOR
40 POWER SUPPLY
RETRO-REFLECTIVEACCUMULATION CHANNEL
OPTIONAL "HSN"SUPPORTS SHOWN
SECTION LENGTH SECTION LENGTH SECTION LENGTH
OVERALL LENGTH
FLOW
24TMe
U.S. Patent Numbers7,243,781 • 7,591,366 7,905,345 • 6,860,381