Hub Drive Cable Puller - Dejana

Hub Drive Cable Puller

• Patented drive system capable of deliv-ering up to 400,000 in lbs. of pulling power!

• Directly connected hydraulic cylinders without toggle linkages for longer ser-vice life.

• Reel unit with 34” lateral (L-R) move-ment for quick, easy pulling and spool-ing.

• Optional “Freewheel Mode” for both underground and overhead applications.

Dejana’s Hub Drive Cable Puller offers a a wide range of unique features for the removal of underground wire and ca-ble in the utility industry. Developed in close cooperation with public utility companies, these units offer a variety of pat-ented design features to increase capacity, provide trouble-free performance, and improve service life. In addition, the new design is 2,500 lbs. lighter than its predecessor! The patented reel drive system is unique in that it is all hydraulic with a direct drive crankshaft powered by two hydraulic cylinders on each arm. The hydraulic lifting cylinders are directly con-nected to the arms without any linkage providing less parts, less breakage, and longer service life. Both arms can deliver 200,000 inch-pounds of torque each (or a combined 400,000 inch-pounds of force), which means that using a 84” diameter reel, the drive system can pull up to 20,000 pounds. In addition, the reel drive, when fully extended and under full

power, can be moved laterally as much as 24 inches in either direction. This feature gives the operator much greater flexibility when positioning the truck on the job site by allowing him to avoid obstacles with the reel unit. It also facilitates even spooling and provides off-set or side-pull capability when installing and removing cable. The winch is designed with an over-wound winch cable that is free from any obstacles on the deck for better operator visibility. Incorporated with the winch is a unique winch line pulling sheave that can be hydraulically adjusted and features a built-in slack tension rollers to take up cable slack for operator safety. The reel and winch systems are designed with a proportional controlled modular hydraulic system that incorporates a variable flow, pres-sure compensated pump with a low volume hydraulic system that requires only 30 gallons of hydraulic fluid. Overall, the truck is designed for heavy-duty operation with a low deck height that is clear of obstacles, convenient compartments with large storage capacity and complete safety features. Hub Drive can be positioned

24” L-R

Features & Specifications Chassis • 60,000 lbs. GVWR. • 14,600 lbs. front axle capacity. • 46,000 lbs. capacity rear axle, single speed, full floating. • 224” wheelbase. • 156” CT. • 120,000-PSI inverted “L” frame reinforcement. • Diesel engine, 250 HP, 800 lb/ft minimum. • Allison automatic transmission, overdrive 6-speed. • Engine-driven, water cooled, air compressor. Body Specifications • Heavy-duty steel platform body, all welded construction. • Outside body dimensions: 95˝ W x 225˝ L. • Long sill construction: 6˝ x 3˝ x ½˝ structural rectangular steel tubing, 32” on center. • Cross sill construction: 6˝ structural steel on 12” centers. • Body floor construction: 1/8” thick removable steel thread plate panels. • Deck height: 58”. Hub Drive • Lift arm capacity:16,000 lbs. min.(32,000 lbs. on the deck) • Reel size capacity (diameter): 5’ to 9’. • Reel size capacity (width): 40” to 72”. • Reel rotational power: 400,000 inch-lbs. @ 10 RPM min. • Hydraulic reel drivers. • Hydraulically powered traversing lift arms, operated independently with a travel of 26”, swing 160˚ from 30˝ from the ground to 30˝ above the deck. • Lift arm cylinders are directly attached to the lift arms and mounted above the deck for easy repair & maintenance, and to protect from road debris.

Remote Control • 2 radio remote controls provided with each vehicle. • Functions: Lift arm (load/unload), motor spin (CW/CCW),

Reel (L&R), Winch (PAY IN/ PAY OUT), Kill switch. • Cab mounted battery charger included. Winch • Bare drum rated capacity: 50,000 lbs. • 875’ of 9/16” Dyform 6 wire rope. • (Winch option of up to 2800’ of 9/16”wire rope.) • Location: Bed mounted at front center of body at the

bulkhead. • Slim design center, rear mounted swivel sheave, hydrau-

lically extendable to 8” and reinforced to the sub struc-ture of the truck body.

• Sheave capacity: 30,000 lbs. min. Hydraulic Specifications: • Direct Mounted load sense, pressure compensating pis-

ton pump rated at 40 GPM at 1300 engine RPM • Hot shift 890 series with ratio of 129% of engine speed • 30 gallon hydraulic reservoir/cooler assembly rated for

40 GPM • Low oil, high temperature and filter change indicator

lights and alarms • Hydraulic valves are of modular design Electrical • Chassis, body lights & reflectors to meet or exceed all

applicable FMVSS108, State, OSHA & local regulations. • LED chassis and platform lighting.

CORPORATE HEADQUARTERS 490 Pulaski Road • Kings Park, NY 11754 Phone: 631-544-9000 • Fax: 631-544-0942

Email: [email protected]

Reel can be used for pulling and placing of cable for underground and overhead applications! • Reel will lock in pulling mode and can be pulled off in

freewheel mode • Immediate STOP and HOLD feature to hydraulically hold

drive motors and prevent cable from going slack • Free Spool feature so reel can pay-off for aerial stringing

Optional Freewheel Mode

* 2500 lbs lighter than original design *