HUAWEI 510

EchoLife HG510 Home Gateway User Manual

HUAWEI TECHNOLOGIES CO., LTD.

Free Communication, Wonderful Life

Thank you for choosing EchoLife HG510 Home Gateway

of Huawei Technologies Co., Ltd.

EchoLife HG510 Home Gateway

User Manual

Issue 02

Product Version V100R001C05

Date 2006-10-14

No. 202012

Copyright © Huawei Technologies Co., Ltd. 2006. All rights reserved.

No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.

All other trademarks and trade names mentioned in this document are the property of their respective holders.

Notice

The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute the warranty of any kind, express or implied.

Caution

The HG510 is used indoors only. Pay attention to the following when installing and using the HG510.

Basic requirements

Take waterproof measures during the storage, transportation and running of the device.

Before installing and using the HG510, read this manual carefully. In case of failure, this equipment must be returned to HUAWEI

Authorized Service Station for servicing to ensure compliance with safety requirements.

If not granted by Huawei beforehand, any company or individual shall not change the HG510 in terms of its structure and safety design and shall be solely responsible for any effect resulted from unapproved modification.

Power supply

The voltage of the power supply shall meet the requirement of the input voltage of the power adapter.

The equipment only can use the AC/DC adaptor that provided with the equipment.

In the case of thundering, unplug the power adapter and all cables.

If the HG510 is not in use for a long time, unplug the power adapter.

Huawei Technologies Proprietary

Placement

Place the HG510 on a stable table. Leave over 10 cm distance around the HG510 for heat dissipation.

Do not place heavy objects on the HG510.

Cleaning

Before cleaning the HG510, switch off the power supply. Clean it using a piece of soft cloth. Do not use liquid or gas

solution.

Note:

The surface of the terminal may become hot if the terminal is used for a long time. However, this is normal. The terminal can still work normally.

About This Manual

After reading this manual, you will know the functions, features, and operations of EchoLife HG510. The whole manual consists of six chapters.

To know about… See…

Features, network application and hardware structure of HG510 Chapter 1 Overview

Installation of HG510 Chapter 2 Installation

Operations of HG510 Chapter 3 Using HG510

Configuration of HG510, including quick setup, and advanced setup Chapter 4 Configuration



To know about… See…

Routine maintenance and troubleshooting of HG510 Chapter 5 Maintenance

Technical terms and abbreviations mentioned in the manual Chapter 6 Appendix

Conventions

Convention Description

Arial Normal paragraphs are in Arial.

Boldface Headings are in Boldface.

Courier New Terminal Display is in Courier New.

Environmental Protection

This product has been designed to comply with the requirements on environmental protection. For the proper storage, use and disposal of this product, national laws and regulations must be observed.

User Manual EchoLife HG510 Home Gateway Table of Contents


i

Table of Contents

Chapter 1 Overview .......................................................................1-1 1.1 System Features................................................................1-1 1.2 Network Application ...........................................................1-1 1.3 Appearance........................................................................1-2

1.3.1 Front Panel ..............................................................1-2 1.3.2 Rear Panel...............................................................1-4

Chapter 2 Installation ....................................................................2-1 2.1 Unpacking Check...............................................................2-1 2.2 Connecting HG510 ............................................................2-1

Chapter 3 Before Using HG510 ....................................................3-1 3.1 Configuration Preparations ................................................3-1 3.2 Establishing the Connection ..............................................3-1

Chapter 4 Configuration................................................................4-1 4.1 Advanced Setup.................................................................4-1

4.1.1 Configuring WAN.....................................................4-1 4.1.2 Configuring LAN ......................................................4-2 4.1.3 Configuring NAT......................................................4-3 4.1.4 Configuring Security ................................................4-5 4.1.5 Configuring Routing.................................................4-9 4.1.6 Configuring DNS....................................................4-12 4.1.7 Configuring DSL ....................................................4-12 4.1.8 Configuring Port Mapping......................................4-13

4.2 Quick Setup......................................................................4-14

User Manual EchoLife HG510 Home Gateway Table of Contents


ii

4.2.1 Configuring PPPoE................................................4-15 4.2.2 Configuring IPoA ...................................................4-20 4.2.3 Configuring Bridge.................................................4-25 4.2.4 Configuring MER ...................................................4-29 4.2.5 Configuring PPPoA................................................4-35

Chapter 5 Maintenance .................................................................5-1 5.1 Querying Information .........................................................5-1 5.2 Managing Device Settings .................................................5-2

5.2.1 Backing Settings......................................................5-3 5.2.2 Updating Settings ....................................................5-4 5.2.3 Restoring to Factory Defaults..................................5-4

5.3 Configuring Access Control ...............................................5-5 5.3.1 Services...................................................................5-5 5.3.2 IP Address ...............................................................5-6 5.3.3 Password.................................................................5-7

5.4 Upgrading Software ...........................................................5-8 5.5 Configuring Diagnostics .....................................................5-9

Chapter 6 Appendix.......................................................................6-1

User Manual EchoLife HG510 Home Gateway Chapter 1 Overview


1-1

Chapter 1 Overview

Thank you for purchasing the EchoLife HG510 Home Gateway device (hereinafter referred to as HG510). With HG510, you can access the Internet using your high-speed ADSL connection.

This user manual will show you how to install and set up HG510.

1.1 System Features HG510 provides the following functions:

Internal ADSL modem for high-speed internet access. 10/100Base-T Ethernet router to provide Internet

connectivity to all computers on your LAN. Network Address Translation (NAT) and IP filtering functions

to provide firewall protection for your computers. Network configuration through DHCP. Compliant with ANSI T1.413 Issue 2, ITU-T G.992.1

(G.DMT), G.992.2 (G.Lite), G.992.3 (ADSL 2) and G.992.5 (ADSL 2+).

Supporting bridging, routing, and PPP modes. Configuration program you access through an HTML

browser.

1.2 Network Application HG510 is a terminal located at the access layer of the network. It

enables medium- and small-sized enterprise users and home users to



1-2

access the IP network through ADSL ports. Figure 1-1 shows a typical networking scheme.

HGW

IPTV

NGN

Internet

Carrier's OSS

IADMS/CPEMS NMS

PC

TV

Ephone

DSLAM

BRAS

CDNIP

Network

F igure 1-1 Networking of HG510

1.3 Appearance The following sections describe the front panel and rear panel of

HG510.

1.3.1 Front Panel

POWER LAN1 LAN2 LAN3 LAN4 ADSL INTERNET

Figure 1-2 Front Panel



1-3

There are several indicators on the front panel of HG510. They indicate the running status of the device. Table 1-1 describes these indicators.

Table 1-1 Indicators on the front panel

Label Color Function

On: The device is powered on. POWER Green

Off: The device is powered off.

On: The Ethernet link is normal.

Blinking: Some data is being transmitted through the Ethernet. LAN 1–4 Green

Off: connection failure between line and Ethernet interface

On: The ADSL link is normal.

Blinking: The ADSL line is being activated. ADSL Green Off: The ADSL connection is not available yet.

On: The connection is set up

Blinking: data is transmitting. INTERNET Green

Off: The connection is broken in the bridging mode or the routing mode, or the connection is not available in the routing mode.



1-4

1.3.2 Rear Panel

ADSL RESET LAN4 LAN3 LAN2 LAN1 POWER ON/OFF

F igure 1-3 Rear Panel

There are several external interfaces on the rear panel. Table 1-2 describes these interfaces.

Table 1-2 Interfaces on the rear panel

Interface Function

ADSL ADSL interface, used to connect the device to a wall-mounted telephone port or a splitter.

RESET A button, used to reset the devices settings to factory defaults.

LAN 1 – 4 Ethernet interface, used to connect the device to a PC or a switch.

POWER Power interface, used to connect the device to the power adapter.

ON/OFF Power switch

Note:

The IP address for equipment management is 192.168.1.1. You can access the IP address through the LAN 1 interface.

User Manual EchoLife HG510 Home Gateway Chapter 2 Installation


2-1

Chapter 2 Installation

2.1 Unpacking Check Before you install HG510, check the parts according to the

packing list.

2.2 Connecting HG510 You need to connect the device to the following objects:

A telephone port A power socket A PC or HUB

Caution:

Before you connect any of the cables, turn off all the devices, including the PC, HUB or switch.

Figure 2-1 shows the connection of every interface on HG510.



2-2

ADSL RESET LAN4 LAN3 LAN2 LAN1 POWER ON/OFF

Splitter

Line Port

Phone Port

Phone

Modem PortPhoneJack

STB

PC

PowerAdapter

Hub

PC1 PC2 PC3

F igure 2-1 Connecting HG510

To connect the device, follow this procedure.

Step Action

1 Connect the DSL interface of HG510 and the Modem port of a splitter by using a telephone cable.

2

Connect the LINE interface of the splitter and the telephone interface on the wall by using another telephone cable. Connect the PHONE interface of the splitter and a telephone set by using a third telephone cable.

3 Connect the LAN interface of HG510 and the network port of a PC (or a HUB) by using a network cable.

4 Connect the power interface of HG510 and the power socket by using the power adapter.



2-3

Caution:

Although you use the same type of cable, The ADSL and PHONE ports are not interchangeable. Do not route the ADSL connection through the PHONE port.

User Manual EchoLife HG510 Home Gateway Chapter 3 Before Using HG510


3-1

Chapter 3 Before Using HG510

3.1 Configuration Preparations To use HG510 ADSL/Ethernet router, you need to have the

following:

ADSL service up and running on your telephone cable, with at least one public Internet address for your LAN.

One or more computers each containing an Ethernet 10Base-T/100Base-T network interface card (NIC).

For system configuration using the supplied web-based program: a web browser such as Internet Explorer V5.0 or later, or Netscape V4.7 or later.

Before you configure HG510, make the following preparations:

Connect the LAN 1 interface of the HG510 with the Ethernet interface of the user' computer by using the network cable.

Power on HG510.

3.2 Establishing the Connection To establish the connection of HG510, do the following:

1) Enter the IP address (default is 192.168.1.1) of HG510 in the Web Browser.

2) Enter the user name and password（default is admin/admin）. Then click OK.

User Manual EchoLife HG510 Home Gateway Chapter 3 Before Using HG510


3-2

If authentication succeeds, the Device Info page is displayed as shown in Figure 3-1.

F igure 3-1 HG510 home page

User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration


4-1

Chapter 4 Configuration

This chapter introduces the configuration of HG510 through Web, including the following contents:

Advanced Setup Quick Setup

4.1 Advanced Setup Advanced Setup allows system administrator to configure the

following:

WAN LAN NAT Security Routing DNS DSL Port Mapping

4.1.1 Configuring WAN

HG510 provides a default PVC. You can choose operation models through Advanced Setup to configure related parameters and establish connection with the network. Figure 4-1 shows the configuration page.



4-2

Note:

If default PVC is deleted, you can set up PVC through Quick Setup. To do this, refer to “4.2 Quick Setup”.

F igure 4-1 Advanced Setup – WAN

This page shows the existing WAN interfaces in the system. To configure a PVC, click Add or Edit. To remove a PVC, click Remove. For details, refer to “4.2 Quick Setup".

4.1.2 Configuring LAN

You can configure the IP address and subnet mask for the LAN interface.



4-3

F igure 4-2 Advanced Setup – LAN

1) Enter the IP address and subnet mask. 2) Select Enable DHCP Server to enable the DHCP function

and configure the related parameters. Alternatively, select Disable DHCP Server as required.

3) Select Enable IGMP Snooping to enable the IGMP Snooping function.

4) If necessary, configure the second IP address and subnet mask for the LAN interface.

5) Click Save to save the settings.

4.1.3 Configuring NAT

NAT settings include Virtual Servers, and DMZ Host function settings.

I. Virtual Servers

Virtual server allows you to direct incoming traffic from WAN side (identified by Protocol and External port) to the internal server with private IP address on the LAN side.



4-4

The internal port is required only if the external port needs to be converted to a different port number used by the server on the LAN side. You can configure up to 32 port conversion rules.

Figure 4-3 shows the configuration page.

F igure 4-3 Advanced Setup – NAT – Virtual Servers

1) Click Add, and select the service you need for this server. 2) Select the service name, and enter the server IP address. 3) Then enter the external/internal port and protocol rules

(system will show the default configuration for this service). 4) Click Save/Apply to finish and apply the new settings.

F igure 4-4 Advanced Setup – NAT – Add new Virtual Server



4-5

II. DMZ Host

HG510 can automatically forward the packets from the applications that do not belong to the Virtual Servers table to a DMZ host.

Figure 4-5 shows the configuration page.

F igure 4-5 Advanced Setup – NAT – DMZ Host

Enter the IP address of the DMZ host and click Save/Apply to activate the DMZ host.

Clear the IP address field and click Save/Apply to deactivate the DMZ host.

4.1.4 Configuring Security

The device provides three functions to ensure the security: outgoing IP filtering, incoming IP filtering and parental control.



4-6

I. Outgoing IP Filtering

F igure 4-6 Advanced Setup – Firewall – Outgoing IP FilteringSetup

By default, all outgoing IP traffic from the LAN is allowed, but some IP traffic will be blocked by setting up filters.

Click Add or Remove to configure outgoing IP filters.

Figure 4-7 Advanced Setup – Firewall – Add new Outgoing IP Filter

1) the outgoing IP traffic by specifying at least one condition. Click Add to create a filter to identify



4-7

If multiple conditions are specified, all conditions must be satisfied in packet filtering.

2) Click Save/Apply to validate the settings.

II. Incoming IP Filtering

By default, all incoming IP traffic from the WAN is blocked when the firewall is enabled. However, some IP traffic will be accepted by setting up filters.

F igure 4-8 Advanced Setup – Firewall – Incoming IP FilteringSetup

1) Click Add to create a filter by specifying at least one condition in the list. If multiple conditions are specified, all the conditions must be satisfied for the filter rule to take effect.



4-8

Figure 4-9 Advanced Setup – Firewall – Add new Incoming IP Filter

) Click Save/Apply to validate the configuration.

those matching with any of the specified rules in the following table

those matching with any of the specified rules in the following table.

2

III. MAC Filtering

MAC Filtering is only effective on ATM PVCs configured in Bridge mode. FORWARD means that all MAC layer frames will be forwarded except

.

BLOCKED means that all MAC layer frames will be blocked, except



4-9

F igure 4-10 Advanced Setup – Firewall – MAC Filtering Setup

Click Add to create a filter to identify the MAC layer frames by specifying at least one condition below. If multiple conditions are specified, all of them take effect.

F igure 4-11 Advanced Setup – Firewall – Add new MAC Filter

4.1.5 Configuring Routing

Two options related to routing information are included.



4-10

I. Default Gateway

1) As shown in Figure 4-12, if you select the Enable Automatic Assigned Default Gateway checkbox, HG510 will assign the first activated PVC from PPPoA, PPPoE, IPoA or MER/DHCP to the default gateway.

2) If the checkbox is not selected, enter the static default gateway and/or a WAN interface.

3) Click Save/Apply to save it.

F igure 4-12 Advanced Setup – Routing – Default Gateway

Note:

After you select the Automatic Assigned Default Gateway checkbox, you need to reboot the router.



4-11

II. Static Route Setup

F igure 4-13 Advanced Setup – Routing – Static Route

1) Click Add to display the Static Route Add page as shown in Figure 4-14.

2) Enter the destination network address, subnet mask, gateway and/or available WAN interface.

3) Click Save/Apply to add the entry to the routing table.

F igure 4-14 Advanced Setup – Routing – Add new Static Route



4-12

4.1.6 Configuring DNS

You can configure the DNS server through this operation. Figure 4-15 shows the configuration page.

F igure 4-15 Advanced Setup – DNS Server

1) If the Enable Automatic Assigned DNS checkbox is selected, HG510 gets the IP address of the DNS Server from one of the activated PVC(s) from PPPoA, PPPoE, IPoA or MER/DHCP.

2) If the checkbox is not selected, enter the IP addresses of the primary DNS server and the secondary DNS server.

3) Click Save to save the settings.

You need to reboot the router to make the new configuration effective.

4.1.7 Configuring DSL

The DSL configuration page allows you to select the DSL modulation support, telephone cable pair setting, and DSL capability.

DSL knowledge is required to configure these settings.



4-13

Consult your Internet Service Provider (ISP) and make sure that these settings match the settings provided by the ISP. Figure 4-16 shows the configuration page.

F igure 4-16 Advanced Setup – DSL

1) Select the parameters and click Save/Apply. 2) Click Advanced Setting to configure the ADSL testing

mode.

4.1.8 Configuring Port Mapping

Port Mapping supports multiple ports to PVC and bridging groups. Each group will perform as an independent network.

F igure 4-17 Advanced Setup – Port Mapping



4-14

First, you need to create mapping groups between LAN and WAN by using the Add button. The Remove button is used to delete the groups. Refer to Figure 4-17.

F igure 4-18 Advanced Setup – Port Mapping – Add

4.2 Quick Setup The system administrator can configure HG510 remotely or

locally through a Web browser. Network configuration need to be planned and decided beforehand.

In different countries and regions, the PVC is different. When the default PVC is deleted, Quick setup will be displayed in left column of the configuration page. Quick setup allows system administrator to select the appropriate operation mode and set the corresponding parameters to establish connection with the network.

Table 4-1 describes the ADSL service modes and the related protocol types.



4-15

Table 4-1 ADSL service modes

Virtual Dialup Dedicated Line

Protocol Type

PPPoE PPPoA Pure bridge MER

RFC 2684 routing (IPoA)

WAN connection

WAN connection

WAN connection

WAN connection

WAN connection

PPPoE user name and password

PPPoA user name and password

VPI/VCI VPI/VCI VPI/VCI

VPI/VCI VPI/VCI None WAN IP WAN IP

None None None Subnet mask

Subnet mask

None None None Default gateway

Default gateway

Preparation None None None DNS DNS

The following sections describe the configuration of these five service modes in details.

4.2.1 Configuring PPPoE

Click Quick Setup in the left frame, and follow the steps below to create a PPPoE connection.

Follow the steps listed below to configure PPPoE.



4-16

Step Action Refer To

1 Configure ATM PVC. I.

2 Select Connection type and encapsulation mode. II.

3 Configure PPP username and password. III.

4 Enable IGMP multicast and WAN service. IV.

5 Configure LAN Service. V.

6 WAN setup-summary. VI.

I. Configure ATM PVC

F igure 4-19 Quick Setup – ATM PVC Configuration

1) Enter the VPI/VCI values. For more information about the actual parameters, contact your ISP.

2) Click Next to go to the next step.



4-17

II. Select Connection Type and Encapsulation Mode

F igure 4-20 Select Connection Type and Encapsulation Mode

1) Select PPP over Ethernet (PPPoE) as the connection type. 2) Select an appropriate encapsulation mode suggested by

your ISP. 3) Click Next to go to the next step.

III. Configure PPP Username and Password

F igure 4-21 Configure PPP Username and Password



4-18

1) As shown in Figure 4-21, enter the username and password of the PPP service and the PPPoE service name.

2) Select a proper authentication mode (AUTO, PAP, CHAP or MSCHAP). For more information about the actual parameters, contact your ISP.

The Dial on demand (with idle timeout timer) function, if checked, a new setup parameter Inactivity Timeout (minutes) [1-4320] will be displayed. This parameter defines the wait time for HG510 to disconnect the PPP link automatically if there is no outgoing packet.

The user is able to assign some specific ATM PVC(s) to run PPPoE, when HG510 has multiple ATM PVC connection.


IV. Enable IGMP Multicast and WAN Service

F igure 4-22 Enable IGMP Multicast and WAN service

1) Select Enable IGMP Multicast, Enable WAN Service, Enable NAT or Enable Firewall as required.




4-19

V. Configure LAN Service

F igure 4-23 Configure LAN Service

1) Enter the IP address (192.168.1.1 by default) and the subnet mask (255.255.255.0 by default).

2) Select Disable/Enable DHCP Server. If you enable DHCP server, configure the DHCP server parameters.

3) If you select Configure the second IP Address and Subnet Mask for LAN interface, configure the related settings.


Note:

The NAT function is enabled by default. It is not displayed on the configuration page, to prevent it from being disabled.



4-20

VI. WAN Setup – Summary

F igure 4-24 WAN Setup – Summary

The last page gives a summary of previous steps. Make sure that the settings match the one provided by your ISP. Then click Save/Reboot to complete the configuration procedure.

4.2.2 Configuring IPoA

Click Quick Setup in the left frame, and follow the steps below to create an IPoA connection.

Follow the steps listed below to configure.

Step Action Refer to


2 Select Connection type. II.

3 Configure WAN IP settings. III.



4-21


4 Enable NAT, IGMP Multicast, and WAN service. IV.

5 Configure LAN service. V.

6 WAN setup–summary. VI.


F igure 4-25 Configure ATM PVC





4-22

II. Select Connection Type

F igure 4-26 Select Connection Type

1) Select IP over ATM (IPoA). 2) Select a proper encapsulation mode in the drop-down list

box. For more information about the actual parameters, contact your ISP.


III. Configure WAN IP Settings

F igure 4-27 Configure WAN IP Settings



4-23

1) Configure the WAN IP Address, WAN Subnet Musk, Default Gateway and DNS. For more information about the actual parameters, contact your ISP.


IV. Enable NAT, IGMP Multicast, and WAN Service

F igure 4-28 Enable NAT, IGMP Multicast, and WAN Service

1) Select/Deselect Enable NAT and Enable Firewall as required.

2) Use Advanced Setup > Firewall to assign filter rules. 3) Select/Deselect Enable IGMP Multicast and Enable WAN

Service as required. 4) Click Next to go to the next step.



4-24



1) Enter the IP address (192.168.1.1 by default) and subnet mask (255.255.255.0 by default).

2) Select Disable/Enable DHCP Server. If you enable DHCP server, configure the DHCP server parameters.

3) If you select Configure the second IP Address and Subnet Mask for LAN interface, configure related settings.




4-25

VI. WAN Setup – Summary


This page gives a summary of previous steps. Make sure that the settings match the settings provided by ISPs, and then click Save/Reboot to complete the configuration procedure.

4.2.3 Configuring Bridge

Click Quick Setup in the left frame, and follow the steps below to create a bridge connection.





3 Configure WAN service. III.

4 Configure IP address. IV.



4-26


5 WAN setup–summary. V.







4-27

II. Select Sonnection Type


1) Select Bridging, and a proper encapsulation mode. For more information about the actual parameters, contact your ISP.


III. Configure WAN Service

F igure 4-33 Configure WAN Service



4-28

1) Select Obtain an IP address automatically to enable this service.

2) Enter a service name and check the box to enable this WAN service.


IV. Configure IP Address

F igure 4-34 Configure IP Address

1) Enter the IP address (192.168.1.1 by default) and the subnet mask (255.255.255.0 by default).




4-29

V. WAN Setup – Summary


The last page gives a summary of previous steps. Make sure that the settings match the settings provided by ISPs, and then click Save/Reboot to complete the configuration procedure.

4.2.4 Configuring MER

Click Quick Setup in the left frame, and follow the steps below to create a MAC Encapsulation Routing (MER) connection.




2 Configure connection type and encapsulation mode. II.

3 Configure WAN IP settings. III.



4-30


4 Enable NAT, IGMP multicast, and WAN service. IV.




Figure 4-36 Configure ATM PVC





4-31

II. Configure Connection Type and Encapsulation Mode

Figure 4-37 Configure Connection Type and Encapsulation Mode

1) information about the actual

Select MAC Encapsulation Routing and a proper encapsulation mode. For more parameters, contact your ISP.




4-32

Configure WAN IP Settings III.

1)

ct Use the following IP address, you need to ask manually.

2) Configure the gateway. If you select Obtain default gateway automatically,

HG510 can get the IP address of the gateway automatically. If you select Use the following default gateway, you need

to enter the IP address of the gateway manually. 3) Enter the IP address of the DNS server.

If you select Obtain DNS server addresses automatically, HG510 can automatically get the IP address of the DNS server from the network.

Figure 4-38 Configure WAN IP Settings

Enter the WAN IP. If you select Obtain an IP address automatically, HG510

can get the IP address automatically from the DHCP server. If you seleenter the IP address and subnet m



4-33

dresses, server

If you select Use the following DNS server adyou need to enter the IP address of the DNS manually.


IV. Enable NAT, IGMP Multicast, and WAN Service

Figure 4-39 Enable NAT, IGMP Multicast, and WAN service

1) Select Enable NAT and Enable Firewall as required. 2) Enter the service name and select Enable WAN Service. 3) Click Next to go to the next step.



4-34



1) Configure the IP address and subnet mask of the LAN interface.

2) Select Disable/Enable DHCP Server as required. If you select Enable DHCP Server, enter the related DHCP parameters.

3) If you select Configure the second IP Address and Subnet Mask for LAN interface, configure related settings. This IP address is for management.




4-35

VI. WAN Setup–Summary


The last page gives a summary of previous steps. Make sure that the settings match the settings provided by ISPs, and then click Save/Reboot to complete the configuration procedure.

4.2.5 Configuring PPPoA

Click Quick Setup in the left frame, and follow the steps below to create a PPPoA connection. The following setting steps are all the same as PPPoE steps.





3 Configure PPP username and password. III.



4-36


4 Enable IGMP multicast and WAN service. IV.




Enter the VPI/VCI values.


1) Enter the VPI/VCI. For more information about the actual parameters, contact your ISP.




4-37

II. Select Connection Type


1) Select PPP over ATM (PPPoA) and a proper encapsulation mode. For more information about the actual parameters, contact your ISP.


III. Configure PPP Username and Password

F igure 4-44 Configure PPP Username and Password



4-38

1) Enter the username and password of the PPP service. 2) Select a proper authentication mode (AUTO, PAP, CHAP or

MSCHAP). For more information about the actual parameters, contact your ISP.




4-39

IV. Enable IGMP Multicast and WAN Service Configuration

Figure 4-45 Enable IGMP Multicast and WAN service configuration

t Enable WAN Service.

vice IP address (LAN IP) and subnet mask, and DHCP

1) Select Enable NAT and Enable Firewall as required. 2) Enter the service name, and selec3) Click Next to go to the next step.


Set the derelated items.



4-40

AN Service

1) Enter the IP address and subnet mask for the LAN interface. d. If you

DHCP

and condary

ed for

Figure 4-46 Configure L

2) Select Disable/Enable DHCP Server as requireselect Enable DHCP Server, configure the relatedparameters.

3) If you select Configure the secondary IP AddressSubnet Mask for LAN Interface, configure the seIP address and subnet mask. This IP address is usmanagement.




4-41

VI. WAN Setup–Summary

re 4-47 WAN Setup – Summary

summary of previous steps. Make sure that the tings provided by ISPs, and then click Sav procedure.

Figu

The last page gives a settings match the sete/Reboot to complete the configuration

User Manual EchoLife HG510 Home Gateway Chapter 5 Maintenance


5-1

hap

5.1 InY y ice,

including:

WAN setting

Route informP settings

settin

Figure 5-1 ows

C ter 5 Maintenance

Querying formation ou can quer the configuration information of the dev

Summary s

Statistics ation

AR DHCP

gs

sh the querying page.

Figure 5-1 Querying device information

To query the device information, do as follows.



5-2

To query… Do…

Summary Select Device Info > Summary to display the Device Info page.

WAN settings Select Device Info > WAN to display the ge. WAN pa

LAN statistics Select Device Info > Statistics > LAN to display the LAN page.

WA evice Info > Statistics > WAN to N statistics Select Ddisplay the WAN page.

ATM elect Device Info > Statistics > ATM to statistics Sdisplay the ATM page.

ADSL statistics

Select Device Info > Statistics > ADSLdisplay the ADSL page.

to

Route information

Select Device Info > Route to display the Device Info-Route page.

ARP settings Select Device Info > ARP to display the Device Info-ARP page.

DHCP settings

display the age.

Select Device Info > DHCP toDevice Info-DHCP Leases p

5.2 Managing Device Settings System Administrator can back up, update and restore HG510

settings in this configuration page.

The settings can be saved from HG510 to computer. The saved setting file can also be loaded from computer to HG510.



5-3

he system administrator to manage large amou

default co

5.2.

x for file

3)

These functions can help tnt of HG510 efficiently.

By restoring default settings, you can set HG510 with the factory nfiguration.

1 Backing Settings

1) Click Backup to display the Settings-Backup page as shown in Figure 5-2.

2) Click Backup Settings to display the dialog bodownloading. Save the HG510 settings to a file on the local PC.

ttings Figure 5-2 Backing up se



5-4

Y

age as

dated accordin

5.2.2 Updating Settings

ou can load settings saved on the local PC to HG510.

1) Click Update to display the Tools-Update Settings pshown in Figure 5-3.

2) Click Browse to find the file containing the settings. 3) Click Update Settings. The HG510 settings will be up

g to the file you selected.

Figure 5-3 Updating settings

5.2.

estore the HG510 settings to factory defaults. It is a good way to restore all settings if many of them are changed improperly.

1) Click Restore Default to display the Tools-Restore Default Settings page as shown in Figure 5-4.

2) Click Restore Default Settings to restore the settings.

3 Restoring to Factory Defaults

You can r



5-5

Figure 5-4 Restoring to factory defaults

5.3 Configuring Access Control ng:

Services

5.3.1 S

and TFTPto Figure 5-5.

You can configure the HG510 to support ACL rules, includi

IP Address Password

ervices

The Services lists the service daemons (including HTTP, ICMP, ) that can be enabled for LAN side, WAN side or both. Refer



5-6

Figure 5-5 Management-Access Control-Services

.

5.3.2 IP Address

ontrol mode is enabled, entities with the IP

nvalid by HG510.

N

1) Select to enable all the WAN and LAN services2) Click Save/Apply to validate the settings.

If Access Caddresses listed in the ACL are allowed to access the local services.

If Access Control mode is disabled, packets from the IP addresses listed in the ACL are deemed i

ote:

The rules in the Acess Contrl List only work on WAN.

This service is an application in Service Control List. Figure 5-6 shows the configuration page.



5-7

F

2) disable Access Control as required. from the ACL, select the Remove ss, and then click Remove.

5.3. P

user accounts: admin, support, and user.

can change and view the DSL tions.

DSL router.

statistics, and upgrade the router's software.

igure 5-6 Management-Access Control-IP Address

1) Click Add to add IP addresses in the ACL. Enable or

3) To delete an IP address option beside the IP addre

3 assword

Access to HG510 is controlled through three

With the admin account, yourouter settings without restric

With the support account, you maintain and diagnose the

With the user account, you access the DSL router, view settings and



5-8

Figure 5-7 Management-Access Control-Passwords

s

5) Click Save/Apply

te Software to display the Update Software page.

2) Click Browse to locate the software on the PC. 3) Click Update Software to start the upgrading process.

The upgrading process takes about two minutes. Do not shut down HG510 during this process.

1) As shown in Figure 5-7, select a “username” such a“admin”.

2) Enter the old password. 3) Enter the new password. 4) Enter the new password again to confirm. Make sure that it

is consistent with the new password. to validate the settings.

5.4 Upgrading Software You can upgrade the software of HG510 through a local PC or

Internet.

1) Click Upda



5-9

Figure 5-8 Update Software

After upgrading is finished, the device will auto-reboot.

Figure 5-9 Update Software

After rebooting, the new version will take effect.

5.5 Configuring Diagnostics This page allows users to test the Ethernet port connection, DSL

port connection, and connection to the ISP. Figure 5-10 shows the configuration page.



5-10

Figure 5-10 Diagnostics

If a test display ain to make sure the

the t ollow the troubleshooting procedure.

s a failure status, click Test ag failure status is consistent.

If est continues to fail, click Help to f

User Manual EchoLife HG510 Home Gateway Chapter 6 Appendix


6-1

Chapter 6 Appendix

ine

M Asynchronous Transfer Mode

CP Dynamic Host Configuration Protocol

LAM Digital Subscriber Line Access Multiplex

ML Hypertext Markup Language

A Internet Protocols Over ATM

ider

L

LAN Local Area Network

M

MAC Media Access Control

N

NIC Network Interface Card

A

ADSL Asymmetric Digital Subscriber L

AT

D

DH

DNS Domain Name Server

DS

H

HT

I

IP Internet Protocols

IPo

ISP Internet Service Prov

User Manual EchoLife HG510 Home Gateway Chapter 6 Appendix


6-2

P

PPP Point to Point Protocol

PPPoA PPP over ATM

PPPoE PPP over Ethernet

PVC Permanent Virtual Connection

R

RIP Routing Information Protocol

S

SNMP Simple Network Management Protocol

T

TCP Transfer Control Protocol

V

VCI Virtual Channel Identifier

VPI Virtual Path Identifier

W

WAN Wide Area Network

HUAWEI TECHNOLOGIES CO., LTD.Huawei Administration Building

Bantian, Longgang DistrictShenzhen, 518129

People’s Republic of China

www.huawei.com202012

HUAWEI 510

Documents

mac layer frames

incoming ip filtering

outgoing ip filtering

proper authentication mode

outgoing ip traffic

proper encapsulation mode

secondary ip address

huawei technologies proprietary