JOB 318 INSTALLATION & MAINTENANCE GUIDE Horizontally Opening Product Line SIDE OPENING Landing Door and Car Door REFER TO GUIDE 315 HSD DOOR OPERATOR FREIGHT DOORS I CAR GATES I CAR ENCLOSURES THE PEELLE COMPANY ® T 1 800 787 5020 F 1 905 846 2161 www.peelledoor.com COMPANY LTD. HSD HORIZONTALLY SLIDING DOORS 04/27/2011
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
JOB 3
18 INSTALLATION& MAINTENANCE GUIDE
Horizontally Opening Product Line
SIDE OPENINGLanding Door and Car Door
REFER TO GUIDE 315HSD DOOR OPERATOR
FREIGHT DOORS I CAR GATES I CAR ENCLOSURESTHE PEELLE COMPANY
®
T 1 800 787 5020 F 1 905 846 2161 www.peelledoor.com
FREIGHT DOORS I CAR GATES I CAR ENCLOSURESTHE PEELLE COMPANY LTD.
® HSD HORIZONTALLY SLIDINGDOORS
04/27/2011
FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
TECHNICAL SUPPORT 1-800-787-5020 ext 244
THE PEELLE COMPANY
®318
INSTALLATION &MAINTENANCE GUIDE
SIDE OPENING
CopyrightCopyright 2006, The Peelle Company Ltd. All Rights Reserved. This document may not be reproduced, electronically or mechanically, in whole or in part, without written permission from The Peelle Company Ltd.
TrademarksAll trademarks or registered product names appearing in this document are the exclusive property of the respective owners.
Warning and DisclaimerAlthough every effort has been made to make this document as complete and accurate as possible, The Peelle Company Ltd. and the document authors, publishers, distributors, and representatives have neither liability nor responsibility for any loss or damage arising from information contained in this document or from informational errors or omissions. Information contained in this document shall not be deemed to constitute a commitment to provide service, equipment, or software by The Peelle Company Ltd. or the document authors, publishers, distributors, or representatives.
Limited WarrantyPeelle warrants to the Customer that goods and services sold will be free from defects in material, workmanship and title and will conform to any mutually agreed upon specifications. If any failure to meet this warranty appears within one year from the date of shipment of the goods or completion of the services, on the condition that Peelle be promptly notified in writing, Peelle will correct any such failure by re-performing any defective portion of the services furnished and supplying conforming goods. If the contract covers installation, repair or maintenance, Peelle will correct the failure by re-performing any defective service, and either repairing or replacing (at its option) any defective goods furnished and any damaged equipment upon which the service was performed resulting from defective service. If re-performance is not practicable, Peelle will furnish without charge services in an amount essentially equal to those which, in Peelle’s sole judgment, would have been required for re-performance.The preceding paragraph a. sets for the exclusive remedy for all claims based on failure of, defect in, goods or services sold hereunder, whether the failure or defect arises before or during the warranty period, and whether a claim, however instituted, is based on contract, indemnity, warranty, tort (including negligence), strict liability or otherwise. The foregoing warranty is exclusive and is in lieu of all other warranties whether written, oral, implied or statutory.
AS TO ALL GOODS SOLD, NO IMPLIED STATUTORY WARRANTEE OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE SHALL APPLY.
FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
TECHNICAL SUPPORT 1-800-787-5020 ext 244
THE PEELLE COMPANY
®318
INSTALLATION &MAINTENANCE GUIDE
SIDE OPENING
Table of ContentsCar Sill InstallationPg 1
Landing Door InstallationPg 2
Car Door InstallationPg 13
WiringPg 25
MaintenanceLook for the Blue Box
Job Site InspectionBefore beginning the installation, ensure that the structural opening is the correct size and that there is adequate support for the entrance sill and header. The entrance must attach to masonry or heavy steel struts. Drywall and light steel studs are not sufficient support.
Also, the elevator must be assembled to a “working platform” stage which can be operated by temporary buttons mounted on the car.
�FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
TECHNICAL SUPPORT 1-800-787-5020 ext 244
THE PEELLE COMPANY
®318
INSTALLATION &MAINTENANCE GUIDE
SIDE OPENING
Car Door Sill Installation HSD Car Door
CLEAR OPENING WIDTH
PLATFORM WIDTH
27 mm [1 1/16"]
DRILL HOLES FOR MOUNTING IN CENTER OF SLOTS USE EXTRALARGE OUTSIDE DIAMETER WASHERS WHEN ASSEMBLING
PLATFORM / CAR
CAR SILL ASSY
INSTALLCAR DOORSILL FIRST
�FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
TECHNICAL SUPPORT 1-800-787-5020 ext 244
THE PEELLE COMPANY
®318
INSTALLATION &MAINTENANCE GUIDE
SIDE OPENING
HEADER ASSEMBLY
HANGER ASSEMBLY
STRUT
LINKAGE
FRAME
STRUT/COUNTERWEIGHT
DOOR PANELS
SILL ASSEMBLYTOE GAURD
LOCK ASSEMBLY
BOTTOM PANELRETAINERS
DOORPANEL CLIPS
UNLOCKINGDEVICE
Landing Door Assembly HSD Landing Door
�FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
TECHNICAL SUPPORT 1-800-787-5020 ext 244
THE PEELLE COMPANY
®318
INSTALLATION &MAINTENANCE GUIDE
SIDE OPENING
Landing Door Frame HSD Landing Door
ALIGNMENT SETTINGALIGNMENT SETTING
32 mm[1 1/4"]
DRILL HOLES IN CENTER OF SLOTS USE EXTRALARGE OUTSIDE DIAMETER WASHERS
PIN SILL TO WALL USING CONCRETE ANCHORSAFTER FINAL ALIGNMENT CHECK BETWEENCAR SILL AND LANDING DOOR SILL IS COMPLETE
Maintenance Ensure there is no more then 1.5 mm gap on either side of the shoes. If gap is greater than 1.5 mm its time to replace the shoes.
1.5 mm (1/16 in)
Maintenance Ensure rollerdiameters are ±2 mm. Ensure rollers are not split or broken.
Ø38.1 mm (1 1/2 in)
Ø31.75 mm (1 1/4 in)
Maintenance Ensure cable is taught (no sag)
Maintenance if bearings are broken or split, replace the connecting point bearings.
Bushing
CarDoor Sill
DIM A + 60mm = 90mm DIM A + 2 3/8 in = 3 9/16 in
Landing Door Track
Landing Door Sill
DIM A = 30mm DIM A = 1 3/16 in
Maintenance Ensure Traction Rollers are in good condition. If Rollers are warn, replace
CLE
AR O
PEN
ING
+262m
m (
10 in)
Maintenance Ensure the Door Clips are installed
Maintenance Ensure there is no more then 1.5 mm gap on either side of the shoes. If gap is greater than 1.5 mm its time to replace the shoes.
1.5 mm (1/16 in)
Maintenance Ensure rollerdiameters are ±2 mm. Ensure rollers are not split or broken.
Ø38.1 mm (1 1/2 in)
Ø31.75 mm (1 1/4 in)
Maintenance Ensure cable is taught (no sag)
Maintenance if bearings are broken or split, replace the connecting point bearings.
Bushing
CarDoor Sill
DIM A + 60mm = 90mm DIM A + 2 3/8 in = 3 9/16 in
Landing Door Track
Landing Door Sill
DIM A = 30mm DIM A = 1 3/16 in
Maintenance Ensure Traction Rollers are in good condition. If Rollers are warn, replace
CLE
AR O
PEN
ING
+262m
m (
10 in)
Maintenance Ensure the Door Clips are installed Maintenance
Ensure there is no more then 1.5 mm gap on either side of the shoes. If gap is greater than 1.5 mm its time to replace the shoes.
1.5 mm (1/16 in)
Maintenance Ensure rollerdiameters are ±2 mm. Ensure rollers are not split or broken.
Ø38.1 mm (1 1/2 in)
Ø31.75 mm (1 1/4 in)
Maintenance Ensure cable is taught (no sag)
Maintenance if bearings are broken or split, replace the connecting point bearings.
Bushing
CarDoor Sill
DIM A + 60mm = 90mm DIM A + 2 3/8 in = 3 9/16 in
Landing Door Track
Landing Door Sill
DIM A = 30mm DIM A = 1 3/16 in
Maintenance Ensure Traction Rollers are in good condition. If Rollers are warn, replace
CLE
AR O
PEN
ING
+262m
m (
10 in)
Maintenance Ensure the Door Clips are installed
�FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
TECHNICAL SUPPORT 1-800-787-5020 ext 244
THE PEELLE COMPANY
®318
INSTALLATION &MAINTENANCE GUIDE
SIDE OPENING
FAST PANEL BRACKET
LINKAGE ASSEMBLY
END BRACKETATTACH TO STRUT
Landing Door Linkage HSD Landing Door
Maintenance Ensure there is no more then 1.5 mm gap on either side of the shoes. If gap is greater than 1.5 mm its time to replace the shoes.
1.5 mm (1/16 in)
Maintenance Ensure rollerdiameters are ±2 mm. Ensure rollers are not split or broken.
Ø38.1 mm (1 1/2 in)
Ø31.75 mm (1 1/4 in)
Maintenance Ensure cable is taught (no sag)
Maintenance if bearings are broken or split, replace the connecting point bearings.
Bushing
CarDoor Sill
DIM A + 60mm = 90mm DIM A + 2 3/8 in = 3 9/16 in
Landing Door Track
Landing Door Sill
DIM A = 30mm DIM A = 1 3/16 in
Maintenance Ensure Traction Rollers are in good condition. If Rollers are warn, replace
CLE
AR O
PEN
ING
+262m
m (
10 in)
Maintenance Ensure the Door Clips are installed
BUSHING
�FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
TECHNICAL SUPPORT 1-800-787-5020 ext 244
THE PEELLE COMPANY
®318
INSTALLATION &MAINTENANCE GUIDE
SIDE OPENING
ENSURE BRACKETS ARE IN LINEWHILE DOORS ARE IN THE OPEN
AND CLOSED POSITION
ENSURE BRACKETS ARE IN LINEWHILE DOORS ARE IN THE OPEN
AND CLOSED POSITION
USE SLOTSFOR ADJUSTMENT
ENSURE DOOR PANELS ARE FLUSH WITH THE FRAMEWHILE IN THE OPEN POSITION.
Landing Door Linkage Adjustment HSD Landing Door
Maintenance Ensure there is no more then 1.5 mm gap on either side of the shoes. If gap is greater than 1.5 mm its time to replace the shoes.
1.5 mm (1/16 in)
Maintenance Ensure rollerdiameters are ±2 mm. Ensure rollers are not split or broken.
Ø38.1 mm (1 1/2 in)
Ø31.75 mm (1 1/4 in)
Maintenance Ensure cable is taught (no sag)
Maintenance if bearings are broken or split, replace the connecting point bearings.
Bushing
CarDoor Sill
DIM A + 60mm = 90mm DIM A + 2 3/8 in = 3 9/16 in
Landing Door Track
Landing Door Sill
DIM A = 30mm DIM A = 1 3/16 in
Maintenance Ensure Traction Rollers are in good condition. If Rollers are warn, replace
CLE
AR O
PEN
ING
+262m
m (
10 in)
Maintenance Ensure the Door Clips are installed
�FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
TECHNICAL SUPPORT 1-800-787-5020 ext 244
THE PEELLE COMPANY
®318
INSTALLATION &MAINTENANCE GUIDE
SIDE OPENING
Interlock Mounting
7 mm [1/4"]ENGAGE DISTANCE
2 mm[1/16"]
SIDE TO SIDE ADJUSTMENTIN AND OUT ADJUSTMENT
HSD Landing Door
Maintenance Ensure there is no more then 1.5 mm gap on either side of the shoes. If gap is greater than 1.5 mm its time to replace the shoes.
1.5 mm (1/16 in)
Maintenance Ensure rollerdiameters are ±2 mm. Ensure rollers are not split or broken.
Ø38.1 mm (1 1/2 in)
Ø31.75 mm (1 1/4 in)
Maintenance Ensure cable is taught (no sag)
Maintenance if bearings are broken or split, replace the connecting point bearings.
Bushing
CarDoor Sill
DIM A + 60mm = 90mm DIM A + 2 3/8 in = 3 9/16 in
Landing Door Track
Landing Door Sill
DIM A = 30mm DIM A = 1 3/16 in
Maintenance Ensure Traction Rollers are in good condition. If Rollers are warn, replace
CLE
AR O
PEN
ING
+262m
m (
10 in)
Maintenance Ensure the Door Clips are installed
Maintenance Ensure there is no more then 1.5 mm gap on either side of the shoes. If gap is greater than 1.5 mm its time to replace the shoes.
1.5 mm (1/16 in)
Maintenance Ensure rollerdiameters are ±2 mm. Ensure rollers are not split or broken.
Ø38.1 mm (1 1/2 in)
Ø31.75 mm (1 1/4 in)
Maintenance Ensure cable is taught (no sag)
Maintenance if bearings are broken or split, replace the connecting point bearings.
Bushing
CarDoor Sill
DIM A + 60mm = 90mm DIM A + 2 3/8 in = 3 9/16 in
Landing Door Track
Landing Door Sill
DIM A = 30mm DIM A = 1 3/16 in
Maintenance Ensure Traction Rollers are in good condition. If Rollers are warn, replace
CLE
AR O
PEN
ING
+262m
m (
10 in)
Maintenance Ensure the Door Clips are installed
7 mm [1/4"]ENGAGE DISTANCE
2 mm[1/16"]
SIDE TO SIDE ADJUSTMENTIN AND OUT ADJUSTMENT
Maintenance Ensure there is no more then 1.5 mm gap on either side of the shoes. If gap is greater than 1.5 mm its time to replace the shoes.
1.5 mm (1/16 in)
Maintenance Ensure rollerdiameters are ±2 mm. Ensure rollers are not split or broken.
Ø38.1 mm (1 1/2 in)
Ø31.75 mm (1 1/4 in)
Maintenance Ensure cable is taught (no sag)
Maintenance if bearings are broken or split, replace the connecting point bearings.
Bushing
CarDoor Sill
DIM A + 60mm = 90mm DIM A + 2 3/8 in = 3 9/16 in
Landing Door Track
Landing Door Sill
DIM A = 30mm DIM A = 1 3/16 in
Maintenance Ensure Traction Rollers are in good condition. If Rollers are warn, replace
CLE
AR O
PEN
ING
+262m
m (
10 in)
Maintenance Ensure the Door Clips are installed
�FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
TECHNICAL SUPPORT 1-800-787-5020 ext 244
THE PEELLE COMPANY
®318
INSTALLATION &MAINTENANCE GUIDE
SIDE OPENING
USE SCREWDRIVER TO HOLDCOUNTERWEIGHT WHILEFASTENING THE CABLE
ATTACH CABLE TO DOOR FAST DOOR PANEL
COUNTERWEIGHT
CABLE
Counterweight Roping HSD Landing Door
Maintenance Ensure there is no more then 1.5 mm gap on either side of the shoes. If gap is greater than 1.5 mm its time to replace the shoes.
1.5 mm (1/16 in)
Maintenance Ensure rollerdiameters are ±2 mm. Ensure rollers are not split or broken.
Ø38.1 mm (1 1/2 in)
Ø31.75 mm (1 1/4 in)
Maintenance Ensure cable is taught (no sag)
Maintenance if bearings are broken or split, replace the connecting point bearings.
Bushing
CarDoor Sill
DIM A + 60mm = 90mm DIM A + 2 3/8 in = 3 9/16 in
Landing Door Track
Landing Door Sill
DIM A = 30mm DIM A = 1 3/16 in
Maintenance Ensure Traction Rollers are in good condition. If Rollers are warn, replace
CLE
AR O
PEN
ING
+262m
m (
10 in)
Maintenance Ensure the Door Clips are installed
Maintenance Ensure there is no more then 1.5 mm gap on either side of the shoes. If gap is greater than 1.5 mm its time to replace the shoes.
1.5 mm (1/16 in)
Maintenance Ensure rollerdiameters are ±2 mm. Ensure rollers are not split or broken.
Ø38.1 mm (1 1/2 in)
Ø31.75 mm (1 1/4 in)
Maintenance Ensure cable is taught (no sag)
Maintenance if bearings are broken or split, replace the connecting point bearings.
Bushing
CarDoor Sill
DIM A + 60mm = 90mm DIM A + 2 3/8 in = 3 9/16 in
Landing Door Track
Landing Door Sill
DIM A = 30mm DIM A = 1 3/16 in
Maintenance Ensure Traction Rollers are in good condition. If Rollers are warn, replace
CLE
AR O
PEN
ING
+262m
m (
10 in)
Maintenance Ensure the Door Clips are installed
SELF CLOSE FEATUREAFTER COUNTERWEIGHT ROPING IS COMPLETE, REMOVE THE SCREWDRIVER AND LET THE DOORS CLOSE.
THE DOORS SHOULD CLOSE FULLY AND LOCK.
THE DOORS SHOULD CLOSE FULLY AND LOCK NO MATTER HOW MUCH THEY ARE OPEN.
�0FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
TECHNICAL SUPPORT 1-800-787-5020 ext 244
THE PEELLE COMPANY
®318
INSTALLATION &MAINTENANCE GUIDE
SIDE OPENING
FILLER
TOE GAURD SUPPORT
TOE GAURD
HEADER COVER
Landing Door Finishing HSD Landing Door
��FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
TECHNICAL SUPPORT 1-800-787-5020 ext 244
THE PEELLE COMPANY
®318
INSTALLATION &MAINTENANCE GUIDE
SIDE OPENING
DOOR CLIPS
ADJUSTABLE
Landing Door Sill & Header HSD Landing DoorMaintenance Ensure there is no more then 1.5 mm gap on either side of the shoes. If gap is greater than 1.5 mm its time to replace the shoes.
1.5 mm (1/16 in)
Maintenance Ensure rollerdiameters are ±2 mm. Ensure rollers are not split or broken.
Ø38.1 mm (1 1/2 in)
Ø31.75 mm (1 1/4 in)
Maintenance Ensure cable is taught (no sag)
Maintenance if bearings are broken or split, replace the connecting point bearings.
Bushing
CarDoor Sill
DIM A + 60mm = 90mm DIM A + 2 3/8 in = 3 9/16 in
Landing Door Track
Landing Door Sill
DIM A = 30mm DIM A = 1 3/16 in
Maintenance Ensure Traction Rollers are in good condition. If Rollers are warn, replace
Maintenance Ensure there is no more then 1.5 mm gap on either side of the shoes. If gap is greater than 1.5 mm its time to replace the shoes.
1.5 mm (1/16 in)
Maintenance Ensure rollerdiameters are ±2 mm. Ensure rollers are not split or broken.
Ø38.1 mm (1 1/2 in)
Ø31.75 mm (1 1/4 in)
Maintenance Ensure cable is taught (no sag)
Maintenance if bearings are broken or split, replace the connecting point bearings.
Bushing
CarDoor Sill
DIM A + 60mm = 90mm DIM A + 2 3/8 in = 3 9/16 in
Landing Door Track
Landing Door Sill
DIM A = 30mm DIM A = 1 3/16 in
Maintenance Ensure Traction Rollers are in good condition. If Rollers are warn, replace
CLE
AR O
PEN
ING
+262m
m (
10 in)
Maintenance Ensure the Door Clips are installed
Maintenance Ensure there is no more then 1.5 mm gap on either side of the shoes. If gap is greater than 1.5 mm its time to replace the shoes.
1.5 mm (1/16 in)
Maintenance Ensure rollerdiameters are ±2 mm. Ensure rollers are not split or broken.
Ø38.1 mm (1 1/2 in)
Ø31.75 mm (1 1/4 in)
Maintenance Ensure cable is taught (no sag)
Maintenance if bearings are broken or split, replace the connecting point bearings.
Bushing
CarDoor Sill
DIM A + 60mm = 90mm DIM A + 2 3/8 in = 3 9/16 in
Landing Door Track
Landing Door Sill
DIM A = 30mm DIM A = 1 3/16 in
Maintenance Ensure Traction Rollers are in good condition. If Rollers are warn, replace
CLE
AR O
PEN
ING
+262m
m (
10 in)
Maintenance Ensure the Door Clips are installed
Maintenance Ensure there is no more then 1.5 mm gap on either side of the shoes. If gap is greater than 1.5 mm its time to replace the shoes.
1.5 mm (1/16 in)
Maintenance Ensure rollerdiameters are ±2 mm. Ensure rollers are not split or broken.
Ø38.1 mm (1 1/2 in)
Ø31.75 mm (1 1/4 in)
Maintenance Ensure cable is taught (no sag)
Maintenance if bearings are broken or split, replace the connecting point bearings.
Bushing
CarDoor Sill
DIM A + 60mm = 90mm DIM A + 2 3/8 in = 3 9/16 in
Landing Door Track
Landing Door Sill
DIM A = 30mm DIM A = 1 3/16 in
Maintenance Ensure Traction Rollers are in good condition. If Rollers are warn, replace
CLE
AR O
PEN
ING
+262m
m (
10 in)
Maintenance Ensure the Door Clips are installed
Panel Installation HSD Car Door
��FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
TECHNICAL SUPPORT 1-800-787-5020 ext 244
THE PEELLE COMPANY
®318
INSTALLATION &MAINTENANCE GUIDE
SIDE OPENING
Maintenance Ensure there is no more then 1.5 mm gap on either side of the shoes. If gap is greater than 1.5 mm its time to replace the shoes.
1.5 mm (1/16 in)
Maintenance Ensure rollerdiameters are ±2 mm. Ensure rollers are not split or broken.
Ø38.1 mm (1 1/2 in)
Ø31.75 mm (1 1/4 in)
Maintenance Ensure cable is taught (no sag)
Maintenance if bearings are broken or split, replace the connecting point bearings.
Bushing
CarDoor Sill
DIM A + 60mm = 90mm DIM A + 2 3/8 in = 3 9/16 in
Landing Door Track
Landing Door Sill
DIM A = 30mm DIM A = 1 3/16 in
Maintenance Ensure Traction Rollers are in good condition. If Rollers are warn, replace
CLE
AR O
PEN
ING
+262m
m (
10 in)
Maintenance Ensure the Door Clips are installed
BUSHING
Panel Linkage HSD Car Door
DRAWING
STEP 14.iam
FAST PANEL BRACKET
LINKGE ASSEMBLY
END BRACKETATTACH TO STRUT
��FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
TECHNICAL SUPPORT 1-800-787-5020 ext 244
THE PEELLE COMPANY
®318
INSTALLATION &MAINTENANCE GUIDE
SIDE OPENING
ENSURE BRACKETS ARE IN LINEWHILE DOORS ARE IN THE OPEN
AND CLOSED POSITION
ENSURE BRACKETS ARE IN LINEWHILE DOORS ARE IN THE OPEN
AND CLOSED POSITION
USE SLOTSFOR ADJUSTMENT
ENSURE DOOR PANELS ARE FLUSH WITH THE FRAMEWHILE IN THE OPEN POSITION.
ENSURE BRACKETS ARE IN LINEWHILE DOORS ARE IN THE OPEN
AND CLOSED POSITION
ENSURE BRACKETS ARE IN LINEWHILE DOORS ARE IN THE OPEN
AND CLOSED POSITION
USE SLOTSFOR ADJUSTMENT
ENSURE DOOR PANELS ARE FLUSH WITH THE FRAMEWHILE IN THE OPEN POSITION.
ENSURE BRACKETS ARE IN LINEWHILE DOORS ARE IN THE OPEN
AND CLOSED POSITION
ENSURE BRACKETS ARE IN LINEWHILE DOORS ARE IN THE OPEN
AND CLOSED POSITION
USE SLOTSFOR ADJUSTMENT
ENSURE DOOR PANELS ARE FLUSH WITH THE FRAMEWHILE IN THE OPEN POSITION.
Maintenance Ensure there is no more then 1.5 mm gap on either side of the shoes. If gap is greater than 1.5 mm its time to replace the shoes.
1.5 mm (1/16 in)
Maintenance Ensure rollerdiameters are ±2 mm. Ensure rollers are not split or broken.
Ø38.1 mm (1 1/2 in)
Ø31.75 mm (1 1/4 in)
Maintenance Ensure cable is taught (no sag)
Maintenance if bearings are broken or split, replace the connecting point bearings.
Bushing
CarDoor Sill
DIM A + 60mm = 90mm DIM A + 2 3/8 in = 3 9/16 in
Landing Door Track
Landing Door Sill
DIM A = 30mm DIM A = 1 3/16 in
Maintenance Ensure Traction Rollers are in good condition. If Rollers are warn, replace
CLE
AR O
PEN
ING
+262m
m (
10 in)
Maintenance Ensure the Door Clips are installed
Panel Linkage Adjustment HSD Car Door
��FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
TECHNICAL SUPPORT 1-800-787-5020 ext 244
THE PEELLE COMPANY
®318
INSTALLATION &MAINTENANCE GUIDE
SIDE OPENING
REMOVE CLIPAFTER INSTAL
CLUTCH ASSEMBLY
MOUNTING STUDS
BELT
BELT CLAMP
KICK OUT CAM
LOCK SWITCHAND BRACKET
BELTTENSIONADJUSTMENT
Lock Mounting HSD Car Door
Maintenance Ensure there is no more then 1.5 mm gap on either side of the shoes. If gap is greater than 1.5 mm its time to replace the shoes.
1.5 mm (1/16 in)
Maintenance Ensure rollerdiameters are ±2 mm. Ensure rollers are not split or broken.
Ø38.1 mm (1 1/2 in)
Ø31.75 mm (1 1/4 in)
Maintenance Ensure cable is taught (no sag)
Maintenance if bearings are broken or split, replace the connecting point bearings.
Bushing
CarDoor Sill
DIM A + 60mm = 90mm DIM A + 2 3/8 in = 3 9/16 in
Landing Door Track
Landing Door Sill
DIM A = 30mm DIM A = 1 3/16 in
Maintenance Ensure Traction Rollers are in good condition. If Rollers are warn, replace
CLE
AR O
PEN
ING
+262m
m (
10 in)
Maintenance Ensure the Door Clips are installed
�0FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
TECHNICAL SUPPORT 1-800-787-5020 ext 244
THE PEELLE COMPANY
®318
INSTALLATION &MAINTENANCE GUIDE
SIDE OPENING
PINS TO PROTRUDE 6 mm [1/4 in]
ADJUSTMENT BOLTFOR PIN PROTRUSION
LOCKING ARM
DOOR OPERATOR CONTROLLER[WIRE BACK TO ELEVATOR CONTROLLER]
CAR DOOR LOCK SWITCH[RUN CABLELS BACK TO ELEVATOR CONTROLLER]
Lock and Operator HSD Car DoorMaintenance Ensure there is no more then 1.5 mm gap on either side of the shoes. If gap is greater than 1.5 mm its time to replace the shoes.
1.5 mm (1/16 in)
Maintenance Ensure rollerdiameters are ±2 mm. Ensure rollers are not split or broken.
Ø38.1 mm (1 1/2 in)
Ø31.75 mm (1 1/4 in)
Maintenance Ensure cable is taught (no sag)
Maintenance if bearings are broken or split, replace the connecting point bearings.
Bushing
CarDoor Sill
DIM A + 60mm = 90mm DIM A + 2 3/8 in = 3 9/16 in
Landing Door Track
Landing Door Sill
DIM A = 30mm DIM A = 1 3/16 in
Maintenance Ensure Traction Rollers are in good condition. If Rollers are warn, replace
CLE
AR O
PEN
ING
+262m
m (
10 in)
Maintenance Ensure the Door Clips are installed
��FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
TECHNICAL SUPPORT 1-800-787-5020 ext 244
THE PEELLE COMPANY
®318
INSTALLATION &MAINTENANCE GUIDE
SIDE OPENING
Clutch Assembly & How it Works HSD Car Door
Landing Door and Car Door in the LOCKED Position
��FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
TECHNICAL SUPPORT 1-800-787-5020 ext 244
THE PEELLE COMPANY
®318
INSTALLATION &MAINTENANCE GUIDE
SIDE OPENING
Clutch Assembly & How it Works HSD Car Door
Landing Door and Car Door in the UNLOCKED Position
��FREIGHT DOORS I CAR GATES I CAR ENCLOSURES
TECHNICAL SUPPORT 1-800-787-5020 ext 244
THE PEELLE COMPANY
®318
INSTALLATION &MAINTENANCE GUIDE
SIDE OPENING
FILLERLIGHT CURTAIN
TOE GUARD SUPPORT
LIGHT CURTAIN
TOE GUARD
DOOR CLIPS
ADJUSTABLE
Maintenance Ensure there is no more then 1.5 mm gap on either side of the shoes. If gap is greater than 1.5 mm its time to replace the shoes.
1.5 mm (1/16 in)
Maintenance Ensure rollerdiameters are ±2 mm. Ensure rollers are not split or broken.
Ø38.1 mm (1 1/2 in)
Ø31.75 mm (1 1/4 in)
Maintenance Ensure cable is taught (no sag)
Maintenance if bearings are broken or split, replace the connecting point bearings.
Bushing
CarDoor Sill
DIM A + 60mm = 90mm DIM A + 2 3/8 in = 3 9/16 in
Landing Door Track
Landing Door Sill
DIM A = 30mm DIM A = 1 3/16 in
Maintenance Ensure Traction Rollers are in good condition. If Rollers are warn, replace
CLE
AR O
PEN
ING
+262m
m (
10 in)
Maintenance Ensure the Door Clips are installed
Finishing Pieces HSD Car Door
Cable runs back to light curtain ControllerSee installation manual located inside the light curtain box