HP0-J51

For interactive and self-paced preparation of exam HP0-J51, try our practice exams. Practice exams also include self assessment and reporting features! 1 www.selftestengine.com

HP EXAM HP0-J51

Installing HP StorageWorks Solutions

Total Questions: 140

http://www.selftestengine.com/�


Question: 1 The HP P2000 G3 FC Storage Array supports both the MSA70 and D2700 disk enclosures. When connecting these enclosures to the P2000 G3 FC controller, where can the MSA70 enclosure be cabled without limiting performance? A. any location B. before all D2700 enclosures C. after all D2700 enclosures D. after the first D2700 enclosure

Answer: C Question: 2 A consultant meets with a customer to define a Disaster Recovery plan based on HP VLS technology. What are the most important parameters the consultant must obtain from the customer? (Select two.) A. Recovery Point Objective B. Restore Point Objective C. Recovery Time Objective D. Retention Point Objective E. Retention Time Objective

Answer: AC Question: 3 Which D2D network configuration mode will improve the availability of overall network bandwidth? A. Single Port Configuration B. Dual Port Configuration C. High Availability (Port Failover) Configuration D. High Availability (Link Aggregation) Configuration

Answer: D



Question: 4 What is the recommended minimum block size that should be configured when backing up to D2D systems? A. 64KB B. 128KB C. 256KB D. 1MB

Answer: A Question: 5 Which HP P4000 management tool should you use to gather storage system status information? A. Centralized Management Console (CMC) B. HP Integrated Lights Out (ILO) C. Web Based Enterprise Management (WBEM) D. System Management Homepage (SMH)

Answer: A Question: 6 A consultant is discussing with a customer how to create a four node multi-site cluster with the P4000 G2 family of products. The customer wants two physical sites, one being the primary. What is the minimum total number of managers that should be run to guarantee quorum? A. 2 B. 3 C. 4 D. 5

Answer: B



Question: 7 Which method of deduplication is used in the HP StoreOnce D2D devices? A. fixed-length data segmenting B. variable-length data segmenting C. object-level differencing D. hash-based chunking

Answer: D Question: 8 When running diagnostics on a P4000 system you notice that the "BBU Capacity Test" is unchecked by default. Why is this? (Select two.) A. The test is not supported on any P4000 system. B. The test can take up to 24 hours to complete. C. The test can overwrite HDD data. D. The test sends data to HP via the Internet. E. The test turns off the controller's cache.

Answer: BE Question: 9 A customer has two HP P2000 G3 FC arrays. One is located at a remote branch office. You have been asked to configure a replication set between the two arrays. Which components are required to form a replication set? (Select two.) A. external view volume B. primary view volume C. host accessible remote volume D. destination snap pool E. source snapshot

Answer: AD



Question: 10 Which browser is supported to access X1000 Windows Server Remote Administration Applet from a non-Microsoft computer? A. Apple Safari B. Google Chrome C. Microsoft Internet Explorer D. Mozilla Firefox

Answer: D Question: 11 In the Storage Management Utility for a P2000 G3, which wizards are available to allow you to quickly and easily set up the system? (Select two.) A. Drive Wizard B. Configuration Wizard C. Replication Setup Wizard D. Hosts Wizard E. Physical Setup Wizard

Answer: BC Question: 12 Where can you find the DHCP-assigned IP address on your D2D system during initial configuration? A. Web Management Interface B. VGA Console C. Telnet D. CommandView TL

Answer: B



Question: 13 Which P2000 G3 Combo FC/iSCSI controller ports would be most suitable for replicating snapshots to remote locations? A. 1GbE iSCSI B. 10GbE iSCSI C. 4Gb FC D. 8Gb FC

Answer: A Question: 14 You are meeting with a customer who has many different backup applications and operating systems. To identify which operating systems are supported with each backup application by VLS and D2D, which HP document should you consult? A. Storage Compatibility Matrix B. EBS Compatibility Matrix C. Backup Solutions Guide D. Storage Backup Matrix

Answer: B Question: 15 What information is displayed in the Configuration View panel overview of the P2000 SMU about the status of any FC hosts attached to it? (Select two.) A. connection type B. WWPN C. HBA Firmware revision D. operating system E. profile

Answer: BE



Question: 16 A customer wants to add a drive enclosure to his existing P2000 G3 system. What is the maximum distance allowed between enclosures? A. 1m B. 2m C. 5m D. 10m

Answer: B Question: 17 Which CLI command is used to verify the setting of the IP address of a P2000 G3 Storage Array? A. show ip-address B. show network-parameters C. show network-address D. show network

Answer: B Question: 18 Your customer wants to monitor the performance of a P4000 G2 system. What is the minimum time sample interval that can be set using the Performance Monitor? A. 1 second B. 5 seconds C. 30 seconds D. 1 minute

Answer: B



Question: 19 What is a feature of P4000 snapshots? A. Snapshots are thin provisioned but can be made fully provisioned after being created. B. As the original volume data changes the snapshot remains the same as the volume at its creation time. C. The same amount of space is reserved for the snapshot as the original volume. D. The snapshot is thinly provisioned and requires no reserve space.

Answer: D Question: 20 In an HP P2000 storage array, the Drive Spin Down (DSD) feature can reduce power consumption by powering down drive spindles. Which statements correctly describe the DSD feature? (Select two.) A. Disk scrubbing is disabled when DSD is enabled. B. Only RAID configured vdisks can be spun down. C. Drive Spin Down delay defaults to 15 minutes. D. Default state is enabled. E. Only drives that reside in vdisks can be spun down.

Answer: AC Question: 21 A customer has an MSA2000 G2 storage array and is upgrading it by replacing the controllers with the new P2000 G3 combo controllers. Which statement is true about the upgraded array? (Select two.) A. Disk shelves will use 6Gb/s SAS bandwidth. B. The vdisk configuration from the old array will be detected and preserved. C. The new volume configuration will overwrite old volumes. D. Snapshot and Volume Copy features will be enabled.

Answer: BD



Question: 22 Which P4000 SmartClone characteristic cannot be changed? A. size B. name C. provisioning (thin/full) D. type (primary/remote)

Answer: B Question: 23 What must you determine about the server and the D2D before running the Installation Wizard? A. They are running on a dedicated 1GbE network. B. They are running on an IPv6 network. C. They are on the same subnet. D. They both have static IP addresses.

Answer: C Question: 24 Which data management features are provided by HP SAN/iQ software? (Select two.) A. data tiering B. Network RAID C. automated archiving D. accelerated deduplication E. automated failover

Answer: BE



Question: 25 Which statement is true about HP P4000 Remote Copy? A. It uses a RAID10 mechanism to mirror all data to a remote system. B. It uses a snapshot mechanism to asynchronously copy a minimum of incremental changes to a remote system. C. It uses a snapshot mechanism to synchronously copy a minimum of incremental changes to a remote system. D. It relies on Continuous Access software to asynchronously copy a minimum of incremental changes to a remote system.

Answer: B Question: 26 A customer wants to use Volume Snapshot/ShadowCopy Service (VSS) to help protect data on an HP Network Storage Server system. Which statements are true about VSS? (Select two.) A. ShadowCopy data is accessible within a share. B. VSS is a replacement for backup. C. Any application can use VSS. D. Once deleted, a ShadowCopy cannot be restored. E. VSS protects against array or volume failure.

Answer: AD Question: 27 Which NIC bonding method is supported on the P4800 SAN? A. network fault tolerant B. active-passive C. link aggregation dynamic mode D. adaptive load balancing

Answer: D



Question: 28 Which HP product utilizes deduplication technology independent of backup software? A. Data Protector Advanced Backup to Disk B. X1000 C. MSL8096 D. D2D4112

Answer: D Question: 29 Which HP Storage product is ideally suited to virtualized environments providing scalable performance and optional 10GbE support? A. EVA4400 B. P2000 G3 C. MSA2000 G2 D. P4500

Answer: D Question: 30 Which statement is true about licensing of HP D2D systems? A. A replication license is required for both the source and the target devices. B. Only one license is required for the replication target. C. D2D replication functionality is included as standard. D. Dynamic deduplication is a licensable feature at extra cost.

Answer: B



Question: 31 Which statement describes HP P4000 SAN/iQ? A. a Centralized Management Console (CMC) that provides an intuitive GUI-based administrative interface B. an operating system that virtualizes multiple storage modules into a flexible, redundant storage pool that is simple to manage C. a Solution Pack for Windows clients that provides VSS and MPIO D. an iSCSI client driver for Windows systems that enables connection to Ethernet storage devices

Answer: B Question: 32 Which D2D Tape Library Emulation type is preferred because it is clearly identifiable as a D2D device if supported by your backup software vendor? A. D2DEML Generic Library B. ESL E Series Library C. MSL G3 Series Library D. D2DBS Generic Library

Answer: D Question: 33 What should you do prior to replacing an HP X1000 system non-hot-swappable FRU? (Select two.) A. Make sure the power cord is connected to the electrical outlet to provide a good ground connection. B. Remove the air filters and store them for reuse. C. Put on your electrostatic discharge (ESD) wrist strap. D. Replace the air filters. E. Disconnect the power cord from the electrical outlet and then from the system.

Answer: CE



Question: 34 When a D2D license is generated, what is needed to register the LTU? A. iLO MAC address B. serial number C. system name D. IP address

Answer: B Question: 35 When setting up a P4000 G2 system for the first time, what must you set up first in the SAN/iQ console? (Select two.) A. host name B. volume letter C. cluster address D. IP address E. host bandwidth

Answer: AD Question: 36 How are external D2D4312 disk shelves identified in the Web Management Interface? A. serial number and port address of the shelf B. MAC address and FQDN of the monitoring unit C. shelf ID and SCSI ID of the I/O module D. card slot and port on the RAID card it is connected to

Answer: D



Question: 37 What is a standard configuration for a P2000 G3 FC? A. snapshot (64), clone, no remote snap B. snapshot (512), clone, remote snap C. snapshot (512), no clone, remote snap D. snapshot (64), no clone, remote snap

Answer: A Question: 38 On which applications can you use storage-allocation wizards to allocate and configure storage on the X1000 and X3000 Network Storage System? (Select three.) A. user-defined applications B. Microsoft Share Point C. Microsoft SQL Server D. Microsoft Exchange E. Lotus Notes

Answer: ACD Question: 39 When managing an HP X1000 Unified Storage Server, which predefined storage reports are available to view? (Select two.) A. Files Backed Up B. Storage Unit Access C. Most Common File Type D. Directory Quota Usage E. Large Files

Answer: DE



Question: 40 Which statement is true about the Remote Snap functionality with the P2000 G3 FC Array? A. Remote Snap utilizes synchronous replication to replicate snapshots to either a remote system or to a different volume on the local system. B. Remote Snap provides support for up to 32 replication sets. C. Remote Snap uses a push operation so the source site will be pushing the information to the target site. D. Remote Snap supports a single system hosting both external view volumes and replication destination volumes.

Answer: D Question: 41 How can you make optimal use of available bandwidth when replicating? A. Use link throttling. B. Minimize the amount of data to replicate. C. Use the tape offload option. D. Make use of concurrency.

Answer: D Question: 42 Which P4000 Network RAID level is recommended for use for applications that primarily perform sequential read operations such as file shares and archives? A. 0 B. 5 C. 6 D. 10+1

Answer: B



Question: 43 When troubleshooting a P2000 G3 array you notice that the health of a particular RAID 6 vdisk is "Degraded." What does this mean? A. The vdisk can perform I/O functions for hosts, but is not fault tolerant. B. The vdisk has degraded performance due to one failed disk, but remains fault tolerant. C. Health status for the vdisk is not available. D. The vdisk has degraded performance due to two failed disks, but remains fault tolerant.

Answer: B Question: 44 Which connector is used for the CLI port on the P2000 G3 FC/iSCSI controller? A. RS232 9 pin connector B. USB mini 5 male connector C. RJ-45 8 pin connector D. RJ-11 6 pin connector

Answer: B Question: 45 Which D2D4312 G2 network port must be connected to run the Installation Wizard and discover the HP D2D on your network? A. 1GbE port 3 B. 10GbE port 1 C. 1GbE port 4 D. 10GbE port 2

Answer: A



Question: 46 Under which device can the Performance Monitoring tool for the P4000 G2 systems be selected? A. each volume B. each cluster C. each node D. each server

Answer: B Question: 47 An HP Network Storage Server is being added to a network, which does not have a DHCP server. To access the Network Storage Server, which access method must be used? A. Remote Server B. Remote Browser C. Direct Attach mode D. Remote Desktop

Answer: C Question: 48 What is the maximum duration of support coverage that can be added with an HP Care Pack for an HP P2000 G3 FC array? A. 1 year B. 3 years C. 5 years D. 7 years

Answer: C



Question: 49 A customer has an HP All-in-One Storage System purchased several years ago. The customer now wants to add more systems of the same type to his environment. Which Network Storage Server is the modern equivalent of the customer's All-In-One system? A. X3000 B. X3800sb C. X5000 D. X1000

Answer: D Question: 50 What should you type into your web browser address field to access the HP X1000 Storage Server Management Console? (Select two.) A. https://<your_machine_serial_number_with_hyphen>/SMC B. https://<IP_Address>/SMC C. https://<IP_Address>/ILO D. https://<IP_Address>:3202 E. https://<your_machine_serial_number_with_hyphen>:3202

Answer: DE Question: 51 Which HP management solution can monitor a P2000 system by using SNMP? A. System Management Utility (SMU) B. P2000 Command View (CV) C. SNMP Trap Adviser (STA) D. System Insight Manager (SIM)

Answer: D



Question: 52 A customer wants to add an HP virtual library to his existing heterogeneous environment. Which reference source should be consulted to check for operating system compatibility and general design guidelines? A. HP Enterprise Backup Solutions website B. StorageWorks Sizer tool C. Data Sheet D. User Guide

Answer: A Question: 53 Which features, only available in Windows Storage Server (WSS) 2008 Enterprise Edition, are included in the X3000 Network Storage System? (Select two.) A. Microsoft Clustering Services B. Storage Manager for SANs C. transportable snapshots D. Single Instance Storage E. Automated Storage Manager

Answer: AC Question: 54 When configuring HP Storage X1000 Data Protection Manager, what information is required to create a Protection Group? (Select three.) A. Protection Group name B. encryption method C. group members D. email address for DPM reports E. job name of DPM-aware backup application F. protection schedule

Answer: ACF



Question: 55 What is the minimum number of storage systems required when choosing a Network RAID 6 data protection level in a P4000 SAN? A. 3 B. 4 C. 5 D. 6

Answer: C Question: 56 A customer has a central data center as well as a number of remote branch offices. The customer is interested in a low-cost entry level virtual library solution for replicating and backing up data from the branch offices to the central data center. Which HP solution best meets the needs of this customer? A. D2D B. NAS C. VLS D. ESL

Answer: A Question: 57 A customer wants to filter the kind of information that can be stored on an HP Network Storage Server system's volumes. Which feature of the Storage Server operating system software must be used to accomplish this? A. file sorter B. print services C. file checking D. file screening

Answer: D



Question: 58 Which P2000 feature performs asynchronous replication of block-level data from a volume on a local storage system to a volume that can be on the same system or on a second, independent system? A. Array Mirror B. Virtual Replicator C. Continuous Access D. Remote Snap

Answer: D Question: 59 Which role can you assign to a D2D Virtual Tape Device? A. snap receiver B. offload device C. primary device D. replication target

Answer: D Question: 60 Which statement is true about the P4000 Multi-Site SANs high availability functionality? A. Failover operations are manually managed via P4000 SAN Storage Manager. B. Clusters cannot traverse multiple subnets. C. 2-way replication can keep data redundant even after a site failure. D. Clusters are geographically aware and use that to optimize the data path.

Answer: D



Question: 61 Which protocols can be used to share data from X1000 storage servers? (Select three.) A. FC B. CIFS C. SCSI D. NFS E. FTP F. SATA

Answer: BDE Question: 62 You are monitoring the performance statistics via the management console of an HP P4000 storage system. Which file format can be exported? A. CSV B. XLS C. PDF D. RPT

Answer: A Question: 63 Which HP solution is ideally suited for low-cost consolidation while providing a 6Gb SAS backend and Remote Snap functionality? A. EVA4400 B. P4500 C. MSA2000i G2 D. P2000 G3

Answer: D



Question: 64 A consultant is trying to identify the source of performance problems within a customer's backup environment. Which HP tools can the consultant use to identify the potential bottlenecks? (Select two.) A. Dev Perf B. Perf Dev C. Sys Perf D. Tape Perf E. Perf Sys

Answer: AC Question: 65 A SmartClone on a P4000 storage system shares a common parent volume with other SmartClones. Which characteristics are shared among all sibling SmartClones? (Select two.) A. cluster B. mirroring level C. size D. type E. provisioning

Answer: AB Question: 66 You have just finished the installation of two P2000 G3 FC/iSCSI Arrays and your customer expresses interest in being able to use Remote Snap Replication. What should you do? A. Emphasize that Remote Snap is not included in the purchase price. B. Inform the customer that Remote Snap functionality is not supported on this array. C. Install a Remote Snap temporary license so they can try it out. D. Explain that Remote Snap functionality only works on a separate subnet.

Answer: C



Question: 67 How does data deduplication work? A. It references files that have been previously stored and only backs up files that have changed since they were last backed up. B. It references blocks of data that have been previously stored and only stores new backup data that is unique. C. It identifies rarely-accessed data on SSD and migrates it to HDD. D. It automatically moves data between RAID levels to conserve disk space.

Answer: B Question: 68 When setting up a replication set using the Replication Wizard with the P2000 G3, which option should be selected to check the link between the systems? A. Verify IP B. Verify Host Link C. Check Links D. Poll system

Answer: C Question: 69 The HP X1000 Unified Storage Server uses the Volume ShadowCopy Service (VSS) to manage snapshots. What does VSS provide? A. file level snapshots B. difference area fully allocated during first snapshot C. necessary administrator privileges for restore D. block level snapshots

Answer: D



Question: 70 Which forms of file serving can be emulated by X1000 and X3000 Network Storage Systems for Windows and UNIX hosts? (Select two.) A. NTFS B. SAMBA C. SIS D. NFS E. SMB

Answer: DE Question: 71 To set up the Network NIC team settings on an HP Network Server system, which utility should be used? A. HP Network Teaming and Configuration Utility B. HP Remote Network Utility C. MPIO Teaming Configuration Utility D. ASM Configuration Utility

Answer: A Question: 72 Which methods can be used to download logs, update firmware and install licenses on the HP P2000 G3 array? (Select two.) A. File Transfer Protocol (FTP) B. System Management Homepage (SMH) C. Remote Copy (RCP) D. System Management Utility (SMU) E. Secure Copy (SCP)

Answer: AD



Question: 73 Which hardware and software combination is required to perform a non-disruptive, on-line controller code upgrade, on a P2000 G3 array? A. single combo controller with multipathing software B. dual iSCSI controllers with Microsoft iSCSI initiator software C. single FC controller with multipathing software D. dual FC controllers with multipathing software

Answer: D Question: 74 During testing of a P4000 installation you suspect that there might be duplicate iSCSI IQNs. On which tab of the iSCSI Initiator Properties window can you check the IQNs? A. Targets B. Discovery C. Volumes and Devices D. Configuration

Answer: D Question: 75 Where should you look for HP D2D backup compatibility information? A. www.hp.com/go/ebs B. www.hp.com/go/spock C. www.hp.com/go/ci D. www.hp.com/go/backup

Answer: A



Question: 76 A consultant is trying to identify the source of performance problems within a customer's backup environment. Which HP tools can the consultant use to identify the potential bottlenecks? (Select two.) A. Dev Perf B. Perf Dev C. Sys Perf D. Tape Perf E. Perf Sys

Answer: AC Question: 77 You are configuring two HP P2000 G3 FC arrays with RemoteSnap. What is required to allow replication between arrays? A. host connected to arrays via Fibre Channel B. host connected to both arrays C. both arrays connected via Fibre Channel D. both arrays connected via Ethernet

Answer: C Question: 78 An HP P4000 storage system is being used with VMware vSphere. An existing 1.75TB volume currently hosts virtual machines (VMs) running an Exchange email environment and has 200GB of free space. A VM for a test application needs to be brought online. Based on best practice, when should a new VM be added to the existing volume? A. when SAN snapshots are being used for both applications, but at different times B. when Exchange is using remote snapshots and the test application is using local snapshots C. when a test application needs to be restored from snapshots weekly and uses only 50GB D. when a test application does not utilize snapshots and will use less than 100GB of disk space

Answer: D



Question: 79 When setting up a replication set using the Replication Setup Wizard with the P2000 G3, which link types can be selected? (Select two.) A. FC B. SAS C. DAS D. iSCSI E. WAN

Answer: AD Question: 80 Which technology does HP P4000 SmartClone Volumes use to minimize space used on the SAN? A. thin provisioning B. striping with parity C. asynchronous scrubbing D. deduplication

Answer: A Question: 81 Which P4000 Network RAID level is recommended only for applications with a requirement for synchronous replication between two sites or locations that must remain fully redundant even after an entire site failure? A. 5 B. 6 C. 10+1 D. 10+2

Answer: D



Question: 82 You have just finished the installation of a P2000 G3 SAS Array and your customer expresses interest in additional functionality. Which functionality would prompt you to seek assistance from your sales/presales representative? A. Drive Spin Down B. Storage Mirroring C. Snapshot D. Volume Copy

Answer: B Question: 83 In an HP P4000 SAN, you can choose the level of data protection by specifying a Network RAID redundancy level. Which Network RAID levels can be configured by the administrator? (Select two.) A. 0 B. 4+1 C. 5+2 D. 6+2 E. 10+2

Answer: AE Question: 84 Which protocols can be used to share data from X1000 storage servers? (Select three.) A. FC B. CIFS C. SCSI D. NFS E. FTP F. SATA

Answer: BDE



Question: 85 Which power saving feature is available with the P2000 G3 array? A. drive spin down B. pooled power backplane C. active cool fans D. platinum efficiency FIO power supply

Answer: A Question: 86 A customer wants to set up protection for his data on an HP Network Storage Server system using Data Protection Manager. The customer's data changes rapidly therefore it is necessary to take many copies of the data during each day. What is the maximum number of recovery points per volume that can be kept? A. 16 B. 32 C. 64 D. 512

Answer: C Question: 87 For the X1000 Network Storage System, the HP Storage Server Management Console provides access to which function? A. Telnet Remote Console B. File Server Resource Manager C. Quick Setup Wizard D. Desktop Indexing Control

Answer: B



Question: 88 On which applications can you use storage-allocation wizards to allocate and configure storage on the X1000 and X3000 Network Storage System? (Select three.) A. user-defined applications B. Microsoft Share Point C. Microsoft SQL Server D. Microsoft Exchange E. Lotus Notes

Answer: ACD Question: 89 When is it useful to limit the maximum size of a virtual cartridge of a D2D system? A. when backup software vendors specify that only small cartridges are supported B. when there are only server image backups and you need one cartridge per server C. when you know you will be moving data to a physical tape with a smaller cartridge capacity D. when you only have small files to back up

Answer: C Question: 90 When running diagnostics on a P4000 system you notice that the "BBU Capacity Test" is unchecked by default. Why is this? (Select two.) A. The test is not supported on any P4000 system. B. The test can take up to 24 hours to complete. C. The test can overwrite HDD data. D. The test sends data to HP via the Internet. E. The test turns off the controller's cache.

Answer: BE



Question: 91 When installing an HP P2000 G3 Storage Array, which type of access is available to the storage system when a DHCP server is not currently available on the management LAN? A. serial cable to the controller B. web-based GUI C. crossover cable to the array management port D. no access

Answer: B Question: 92 Which sophisticated data management features does the HP SAN/iQ software provide for the P4000? (Select two.) A. inline deduplication B. zero downtime backup integration C. automated tiering D. automated failover E. storage pooling

Answer: DE Question: 93 A customer owns an HP MSA2000 G2 FC system. The customer wants to upgrade this system and take advantage of the extra functionality of the P2000 G3 system. What is the only item that must be upgraded in the existing array? A. chassis B. hard disks C. controller D. virtual volume

Answer: C



Question: 94 You have an HP P4000 Management Group with 5 storage systems running a manager process. How many manager systems can be offline without impacting access to this Management Group? A. 2 B. 3 C. 4 D. 5

Answer: A Question: 95 Which P2000 G3 Combo FC/iSCSI controller ports would be most suitable for replicating snapshots to remote locations? A. 1GbE iSCSI B. 10GbE iSCSI C. 4Gb FC D. 8Gb FC

Answer: A Question: 96 When configuring HP Storage X1000 Data Protection Manager, what information is required to create a Protection Group? (Select three.) A. Protection Group name B. encryption method C. group members D. email address for DPM reports E. job name of DPM-aware backup application F. protection schedule

Answer: ACF



Question: 97 When scheduling snapshots on an HP P4000 storage array, which criteria can you specify? (Select two.) A. minimum number of snapshots to retain B. maximum time to retain snapshot C. maximum size of snapshot D. free space required to create snapshot E. number of snapshots to retain

Answer: BE Question: 98 What is the name of the management software for the P4000 G2 SAN family of products? A. Central Monitoring Unit B. Storage Configurator C. Configuration Console D. Centralized Management Console

Answer: D Question: 99 Which statement is true about the Remote Snap functionality with the P2000 G3 FC Array? A. Remote Snap utilizes synchronous replication to replicate snapshots to either a remote system or to a different volume on the local system. B. Remote Snap provides support for up to 32 replication sets. C. Remote Snap uses a push operation so the source site will be pushing the information to the target site. D. Remote Snap supports a single system hosting both external view volumes and replication destination volumes.

Answer: D



Question: 100 What is a feature of P4000 snapshots? A. Snapshots are thin provisioned but can be made fully provisioned after being created. B. As the original volume data changes the snapshot remains the same as the volume at its creation time. C. The same amount of space is reserved for the snapshot as the original volume. D. The snapshot is thinly provisioned and requires no reserve space.

Answer: D Question: 101 Which D2D2500 port must be connected to enable connection to the Web Management Interface? A. LAN port 1 B. LAN port 2 C. LAN port 3 D. LAN port 4

Answer: A Question: 102 Which statement describes HP P4000 SAN/iQ? A. a Centralized Management Console (CMC) that provides an intuitive GUI-based administrative interface B. an operating system that virtualizes multiple storage modules into a flexible, redundant storage pool that is simple to manage C. a Solution Pack for Windows clients that provides VSS and MPIO D. an iSCSI client driver for Windows systems that enables connection to Ethernet storage devices

Answer: B



Question: 103 What is the maximum length SAS cable allowed in any HP P2000 G3 configuration? A. 0.5m B. 1.0m C. 2.0m D. 3.0m

Answer: C Question: 104 Which HP Network Storage Systems ship with the Enterprise version of Windows Storage Server 2008? (Select two.) A. X1000 B. X1008 C. X1800sb D. X3000 E. X3800sb

Answer: DE Question: 105 What is the status of the D2D4312 when you add a drive shelf to increase the capacity of the storage pool? A. rebuilding B. online C. suspended D. offline

Answer: D



Question: 106 You have just finished the installation of two P2000 G3 FC/iSCSI Arrays and your customer expresses interest in being able to use Remote Snap Replication. What should you do? A. Emphasize that Remote Snap is not included in the purchase price. B. Inform the customer that Remote Snap functionality is not supported on this array. C. Install a Remote Snap temporary license so they can try it out. D. Explain that Remote Snap functionality only works on a separate subnet.

Answer: C Question: 107 A consultant meets with a customer who is interested in purchasing a P2000 G3 system with SATA drives. What is the standard warranty included for this type of disk? A. one year B. two years C. three years D. five years

Answer: A Question: 108 You are setting up a P2000 G3 system with redundant controllers for the first time in an environment where there is no DHCP server present. What is the default address of controller B? A. 10.0.0.1 B. 10.0.0.2 C. 10.0.0.3 D. 10.0.0.4

Answer: C



Question: 109 Which P2000 user has fixed permission options? A. Monitor B. Configure C. Manage D. Diagnose

Answer: C Question: 110 A consultant meets with a customer to identify how to improve his existing backup strategy by integrating a virtual backup solution. What is the most important factor to consider when analyzing the existing environment? A. what to optimize or improve B. data layout C. age of host systems D. number of tapes used to do the backup

Answer: A Question: 111 Which standard feature of Windows 2008 provides file level deduplication on the X1000 and X3000 Network storage systems? A. accelerated deduplication B. dynamic deduplication C. Single Instance Storage D. StoreOnce

Answer: C



Question: 112 What is the maximum number of concurrent backups you should configure for best performance on a D2D2500? A. 2 B. 4 C. 6 D. 8

Answer: B Question: 113 You are monitoring the performance statistics via the management console of an HP P4000 storage system. Which file format can be exported? A. CSV B. XLS C. PDF D. RPT

Answer: A Question: 114 What are benefits of an HP P4000 Storage IP SAN? (Select two.) A. Non-HP storage systems can be added to a cluster. B. Several clustered storage systems can be managed as one storage pool. C. Additional capacity can be added to a cluster with no downtime. D. Capital expenditure is lower than for an FC SAN, but operational expenditure is higher. E. Capital expenditure is higher than for an FC SAN, but operational expenditure is lower.

Answer: BC



Question: 115 What is the name of the storage area that is reserved when a P2000 snapshot is created? A. snap pool B. copy block C. spare space D. replication volume

Answer: A Question: 116 A customer has a 3-node HP P4000 SAN solution and has implemented Network RAID 0 on this system. The customer now must allocate new volumes, which contain critical dat a. Performance level is not important with these volumes. Which Network RAID level should you suggest for maximum data protection? A. 0 B. 6 C. 10+1 D. 10+2

Answer: C Question: 117 Where does deduplication take place in a non-replicated D2D environment? A. on the target only B. on the source only C. on both source and target D. on the host system

Answer: A



Question: 118 Two HP P2000 G3 FC Storage Arrays are configured for replication. Which fault condition will cause the loss of replication between the storage arrays in a RAID 5 configuration? A. removal of disk in a source array B. removal of disk in a destination array C. cable pull at a destination controller D. cable pull at a source controller

Answer: C Question: 119 What is a benefit of utilizing P4000 snapshots in a vSphere environment? A. It can be used to enhance vSphere's HA/DRS technology. B. It provides synchronous mirroring of volumes for automatic failover. C. It allows you to seamlessly migrate volumes between storage nodes. D. It is possible to snapshot all virtual machines on a single volume at once.

Answer: D Question: 120 The HP X1000/X3000 Unified Storage Servers provide support for sharing print functions. Which statements are true? (Select two.) A. USB connected printers can be shared to UNIX clients. B. Network attached printers can be shared to Windows clients. C. UNIX clients can access any supported shared printer. D. Windows clients can only access local or remote printers at one time. E. Printers listed in Active Directory are only accessible to Windows clients.

Answer: BC



Question: 121 A Windows 2008 Server needs to be connected to an HP P4000 SAN. Which step must be completed before you can connect this server to a volume on the SAN? A. install iSCSI Initiator B. format volume C. create server profile D. create disk partition

Answer: C Question: 122 Which tool should you use to verify the SAN/iQ network configuration? A. Network Configuration B. Device Manager C. iSCSI Initiator configuration tab D. Best Practice Analyzer

Answer: D Question: 123 On a P2000 G3 system you want to create multiple volumes with the same base name and size, and map them all in the same way. What should you create? A. a Volume Group B. a Vdisk Group C. a Volume Set D. a Snapshot Set

Answer: C



Question: 124 A consultant meets with a customer to define the level of support required in a new data center. The customer needs daily (including holidays) round-the-clock support but does not require any proactive services. Which Care Pack best matches the customer's requirement? A. Support Plus 24 B. Proactive 24 C. HP Support Plus D. Warranty Plus 24

Answer: A Question: 125 Which HP disk-based backup solution can provide support for Fibre Channel-based backups and utilizes HP StoreOnce technology? A. VLS9000 B. VLS12000 C. D2D4112 D. D2D4106i

Answer: C Question: 126 When managing an HP X1000 Unified Storage Server, which predefined storage reports are available to view? (Select two.) A. Files Backed Up B. Storage Unit Access C. Most Common File Type D. Directory Quota Usage E. Large Files

Answer: DE



Question: 127 What should you do prior to replacing an HP X1000 system non-hot-swappable FRU? (Select two.) A. Make sure the power cord is connected to the electrical outlet to provide a good ground connection. B. Remove the air filters and store them for reuse. C. Put on your electrostatic discharge (ESD) wrist strap. D. Replace the air filters. E. Disconnect the power cord from the electrical outlet and then from the system.

Answer: CE Question: 128 When installing an HP X1000 Unified Storage System, which type of access to the system is supported if a DHCP server is not available on the network? A. Web Browser B. Telnet C. Direct Attach D. Remote Desktop

Answer: C Question: 129 Your customer wants to control space allocated on an HP Network Server X3000 by using quotas. Which type of quotas can be set up? A. user-based B. volume-based C. directory-based D. disk-based

Answer: C



Question: 130 What is a dedicated slot that is used to hold a cartridge that is ready for exporting to or importing from the library? A. offload slot B. replication slot C. copy slot D. mail slot

Answer: D Question: 131 What is a P4000 Remote Copy? A. It is a SmartClone that is copied to a remote snapshot. B. It is a MirrorClone that is copied to a remote cluster. C. It is a snapshot that is copied to a dedicated host. D. It is a snapshot that is copied to a remote cluster.

Answer: D Question: 132 Which technology is leveraged by HP D2D Backup Systems, enabling customers to consolidate multiple remote sites into a single replication target using Low Bandwidth Replication (LBR)? A. advanced backup to disk B. change block tracking C. accelerated deduplication D. HP StoreOnce deduplication

Answer: D



Question: 133 Your customer is a small to medium-sized business using DL-based servers and wants to implement a network-based storage architecture with the possibility to cluster for high availability. Which HP X-series products will fit this customer's requirements? A. X3000 B. X5000 C. X1800sb D. X3800sb

Answer: A Question: 134 What is the maximum duration of support coverage that can be added with an HP Care Pack for an HP P2000 G3 FC array? A. 1 year B. 3 years C. 5 years D. 7 years

Answer: C Question: 135 What information is displayed in the Configuration View panel overview of the P2000 SMU about the status of any FC hosts attached to it? (Select two.) A. connection type B. WWPN C. HBA Firmware revision D. operating system E. profile

Answer: BE



Question: 136 How does data deduplication work? A. It references files that have been previously stored and only backs up files that have changed since they were last backed up. B. It references blocks of data that have been previously stored and only stores new backup data that is unique. C. It identifies rarely-accessed data on SSD and migrates it to HDD. D. It automatically moves data between RAID levels to conserve disk space.

Answer: B Question: 137 When configuring a Data Protection Manager (DPM) server, which entity is the same across all members of a protection group? A. protection schedule B. protection drive letter assignment C. protection source volume D. protection server name

Answer: A Question: 138 If an HP Network Storage Server system is deployed into a workgroup environment, where is the user and group information stored? A. on the domain controller B. locally on the device C. on the primary server in the workgroup D. locally on the clients in the workgroup

Answer: B



Question: 139 Which method of deduplication is used in the HP StoreOnce D2D devices? A. fixed-length data segmenting B. variable-length data segmenting C. object-level differencing D. hash-based chunking

Answer: D Question: 140 A volume on an HP P4000 SAN is being replicated to another HP P4000 SAN at a remote location. Once the volume has been created at the remote site, what is the next step in the Remote Copy process of making a copy of the data at the remote site? A. Data is copied from the production snapshot to the remote volume. B. A snapshot is created at the remote site. C. Data is copied from the production volume to the remote volume. D. A snapshot is created at the production site.

Answer: B


HP0-J51

Documents

hba firmware

single instance

iscsi client

made fully

good ground

x1000 storage

directory

centralized