How To Turn An Old Router Into A Wireless Bridge You may some day encounter a situation in which you will require a wireless internet connection for a desktop computer. Perhaps you have decided to move your office from one room to another in your home. However, the new room does not have the cable or telephone connection you need to bring that computer online. Before you go out and buy a wireless network card or attempt to run wire through your attic, you might be able to save yourself time and money if you have an old wireless router lying around. You may be able to upgrade your old router with a different firmware that will allow it to act as a wireless bridge . That is, turn your old router into wireless bridge. A wireless bridge allows you to connect one network to another over the airwaves, rather than having to run wire from one room to another.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
How To Turn An Old Router Into A Wireless Bridge
You may some day encounter a situation in which you will require a wireless internet connection for a desktop computer. Perhaps you have decided to move your office from one room to another in your home. However, the new room does not have the cable or telephone connection you need to bring that computer
online.
Before you go out and buy a wireless network card or attempt to run wire
through your attic, you might be able to save yourself time and money if
you have an old wireless router lying around. You may be able to upgrade
your old router with a different firmware that will allow it to act as
a wireless bridge. That is, turn your old router into wireless bridge. A
wireless bridge allows you to connect one network to another over the
airwaves, rather than having to run wire from one room to another.
The free firmware that makes this possible is called DD-WRT. Before
reading further, check the DD-WRT supported device list to see if your
router is supported. If it is supported, be sure to check out the notes for
running DD-WRT on the supported device page. You’ll need to refer to
the recommended installation method later.
Requirements
- Broadband internet connection.
- Two wireless routers:
o One connected to your broadband internet connection to serve as the
access point.
o One connected to other machine(s) that need to connect to web. This one
will need to support DD-WRT.
Initial Setup
1. Make sure your main internet router is working properly. Verify the
wireless connection is working properly by connecting a laptop or some
other device.
2. Set up the remote computer at the remote location.
3. Connect the remote computer to the router you will be installing DD-
WRT onto. Just plug it into one of the ports on the hub (i.e. not the internet
port or uplink port).
4. Open your browser and connect to the router’s web configuration page.
If you’re not sure what the address is, you may need to refer to the
router’s manual. If the router is running DHCP, it is likely to be the address
of the computer’s gateway. In Windows XP, go to the Control Panel and
then Network Connections. There Double-click on your LAN connection
and go to the Support tab. The default gateway will be listed there. You
can also check it on CIRT.netalong with other details such default
username and password for the router.
Download DD-WRT
Now, you need to download the DD-WRT.
1. Go to the DD-WRT download page and Navigate to
the stable directory.
2. Navigate to the latest version (you can sort by date descending).
3. Navigate to the Consumer directory.
4. Navigate to the proper directory for your router’s manufacturer and
then the model/version of the router. You should be able to find the model
and version number printed somewhere on the router. http://www.dd-
wrt.com/wiki/index.php/Supported_Devices
6. Download the .bin file of your choice.
The notes for running DD-WRT on the supported device list may
mandate you use a specific version. If not, I recommend you select either
the mini or the standard. If you want to know the differences between the
different versions, check out the File Versions section of the What is DD-
WRT? page of the DD-WRT wiki.
Install DD-WRT
If you downloaded DD-WRT from your main internet connection, you may
need to copy it to a USB drive to install it on the remote router from the
remote computer. The remaining instructions are to be run from the
remote computer connected to the remote router where DD-WRT is to be
installed.
Install DD-WRT according to the installation instructions on the wiki. Use
the installation method recommended for your device in the notes on the
supported device page (if applicable).
Warning: It is possible to brick your router when you install the new
firmware (i.e. render it useless). Please take caution in reading the
installation instructions carefully. I recommend you install DD-WRT on an
old router that you are currently not using, so that if something does go
awry there is no major loss.
Configuring DD-WRT as a Client Bridge
1. Once you have DD-WRT installed, open your browser to
http://192.168.1.1 and log into the router. In older versions of DD-WRT,
the default username is root and the default password is admin. Be sure
to change the default password to secure your router.
2. Next, click on the Wireless tab at the top.
3. Set the Wireless Mode to Client Bridge. Then click Apply.
4. Set the SSID to that of your main wireless router that is connected to
the Internet. In my case, my main wireless router SSID is sierra. Then
click Apply.
5. Click on the Wireless Security tab in the second row of tabs, and
configure the router to match the security settings as your main router. In
my case, my main wireless router has WPA security mode with TKIP
shared key, so I set up DD-WRT to match it.
6. Click Apply.
7. Click the Setup (very first tab in the upper left) to configure the LAN
settings.
8. Assign the router a Local IP Address on the same subnet as your main
router, but give it a different address. That means that all the numbers
for the address will be the same as the main router except for the
numbers in the fourth box. For example, the address of my main router is
192.168.1.1 so I gave my DD-WRT router an IP of 192.168.1.2.
9. Set the Subnet Mask to 255.255.255.0.
10. Set the Gateway and Local DNS to the address of the main router.
11. Click Apply.
Your DD-WRT router should now allow you to connect your remote
computer to your main internet router through the airwaves! If you ever
need to reconfigure the DD-WRT router, just be sure to remember the new
IP address that you assigned in step number 8. You could always use a
nice label maker and slap it right onto the router.
How to connect my BRAVIA® Internet TV with Wireless LAN Ready or Built-in Wireless LAN to a Internet network?
Article ID:403899(modified 11 Jan 2012)
Applicable Models
Question
Connect my BRAVIA® Internet TV with Wireless LAN Ready or Built-in Wireless LAN to a high-speed Internet
network.
Answer
This solution begins by explaining the difference between wireless LAN-ready and built-in wireless LAN. For
information regarding which of these your Sony® TV is equipped with, refer to the iManual supplied with the TV.
Manuals also are available online through the Manuals link on this page.
Wireless LAN-ready:
Bring wireless Internet access to your Wi-Fi® ready BRAVIA HDTV with the UWA-BR100 wireless LAN adapter.
This adapter plugs into your USB input on your TV, and with WPS (Wi-Fi Protected Setup) functionality, it's
simple to get your TV connected to your home network no matter what type of Wi-Fi you are using.
NOTE: The USB wireless LAN adapter is available as an optional accessory. The USB Wireless LAN adapter
may not be available in some areas. KDL EX700, HX700, HX800, HX900 Series are Wireless LAN-ready.
Built-in wireless LAN:
The built-in Wireless LAN device allows you to access the Internet and your home network without having to
connect a separate adapter. With this feature, you can easily connect to a wireless LAN and enjoy the benefits of
networking in a cable-free environment. KDL LX900, NX700, NX800 Series are Wi-Fi Integrated.
Network Setup:
IMPORTANT:
If you are using a wireless hub, router or game adapter, you must select Wired Setup instead of Wireless
Setup. The Wireless Setup is only for use with Sony Wireless LAN Ready TVs (with USB Wireless LAN Adapter
UWA-BR100) or Built-in Wireless LAN TVs.
For the Wireless LAN Ready TVs, only the UWA-BR100 is supported. PC USB Wireless LAN adapters are not
supported.
Using the network feature, you can connect your TV to the Internet. The setup procedure differs depending on
the type of network and LAN router. Before setting up your Internet connection, be sure to set up a wireless LAN
router.
1. Using the supplied remote, press the HOME button.
2. Select Settings.
3. Select Network Set-up.
4. Select View Network Status.
5. Press ENTER to confirm network status.
6. Select either Wireless Set-up or Wired Set-up.
7. Select Scan. Scan can be used to set up any type of wireless network. You will need to know your
network SSID andsecurity key or password for secured networks. If using a secure network follow the correct
sub step.
* A WPS (Push Button) W-Fi Protected Setup (WPS) makes network setup as easy as the touch of a button.
* A WPS (PIN) Allows for WPS setup of your TV by providing a PIN that you will set in your wireless router.
* Secured Network without Wi-Fi Protected Setup (WPS)
Secured Network without Wi-Fi Protected Setup (WPS)
NOTE: For setting up a wireless LAN, SSID (wireless network name) and security key (WEP or WPA key) will be
required. If you do not know them, consult the instruction manual of your router or contact you Intersent Service
Provider (ISP).
1. Using the supplied remote, press the HOME button.
2. Select Settings.
3. Select Network Set-up.
4. Select Wireless Set-up.
5. Select Scan.
6. Select your network from the list.
7. Follow the instructions that appear on the setup screen.
Unsecured Network with Any Type of Wireless LAN Router:
NOTE: For setting up a wireless LAN, the SSID (wireless network name) will be required. Security key (WEP or
WPA key) will not be required because you need to select no security method in this procedure.
1. Using the supplied remote, press the HOME button.
2. Select Settings.
3. Select Network Set-up.
4. Select Wireless Set-up.
5. Select Scan.
6. Select your network from the list.
7. Follow the instructions that appear on the setup screen.
Secured Network with Wi-Fi Protected Setup (WPS):
NOTE: The WPS standard makes setup of a secure wireless home network as simple as pressing the WPS
button on the wireless LAN router. Before setting up a wireless LAN, check the location of the WPS button on the
router and verify how to use it.
1. Using the supplied remote, press the HOME button.
2. Select Settings.
3. Select Network Set-up.
4. Select Wireless Set-up.
5. Select WPS (Push Button) for Push Button method or WPS (PIN) for PIN method.
6. Follow the instructions that appear on the setup screen.
NOTE: To connect to a wireless LAN with WPS, your wireless LAN router needs to support the WPS standard.
Manually Setting the IP Address and Proxy Settings:
NOTE: Enter the respective alphanumeric values for your router if necessary. The items that need to be set (e.g.
IP Address, Subnet Mask, DHCP) may differ depending on the Internet service provider or router. For details,
refer to the instruction manuals provided by your Internet service provider, or those supplied with the router.
1. Select Auto to set the IP Address and proxy server automatically or “Custom” to set them manually.
2. Follow the instructions that appear on the setup screen.
NOTE: If you use WPS for network setup, the security settings of the wireless LAN router activate, and any
equipment previously connected to the wireless LAN in a non-secure status will be disconnected from the
network. In this case, activate the security settings of the disconnected equipment and then reconnect. Or, you
can deactivate the security settings of the wireless LAN router, and then connect the equipment to a TV in a non-
secure status.
Feedback
Please select an option after reviewing the solution above.
This solution helped to resolve my issue
The solution is not related to the title
The solution is not detailed enough to resolve my issue
This solution is too complex or too confusing
I tried this solution but it could not solve my issue
Internet TV Box
Breakthroughs in technology are creating opportunities for consumers to expand the capabilities
of their television-viewing experiences. One notable technological development is the
introduction ofinternet-capable TVs. To connect the Internet to a TV, owners need to have an
Internet-ready TV, Internet access, an Ethernet or wireless connection, and a remote device that
can initialize the Internet menus on the televisions. A number of other devices and services are
valuable to enhance a user’s experience, but these items are not mandatory for operating an
Internet-ready TV. Buyers can find the tools they need to access the Internet through their TVs at
local big-box stores, mass retail and department stores, and electronic shops. For buyers that
favor the convenience and variety of online shopping, eBay is a great option that carries Internet-
ready TVs and accessories from a wide range of manufacturers.
Connecting a TV Directly to the InternetA distinction must be made when discussing connecting a TV directly to the Internet versus
connecting a computer or laptop to a TV. Direct Internet access supplies users with more options
that are uniquely tailored to the TV-viewing experience. In contrast, a computer or laptop can be
connected to a TV, which turns the television into a type of projector. Doing this provides users
with limited functions and might compromise the integrity of the TV’s picture resolution.
People who opt to use their standard TVs as projectors will typically employ computers or laptops
that have an HDMI output that can be connected to an HDMI input on the back of their TVs. The
connection is made using an HDMI cable. Once the connection is established, users might need
does not feature wireless connections, an external TV wireless adapter can be added to the TV
to support wireless connectivity. Wireless connections are beneficial because they free users
from the spatial constraints often associated with connections maintained via Ethernet cables.
There might be problems, however, with streaming HD video through a wireless connection
without video stutters occurring.
4. Remote Device for Initiating Internet AccessWhen buyers purchase an Internet-ready TV, a proprietary remote control will be included as part
of the TV package. These remote controls typically feature a button that launches the Smart TV’s
Internet menus. Each Smart TV manufacturer has a different user interface for accessing the
Internet. Some employ a system of windows that allow users to choose options, while others
utilize a dashboard or vertical menu scheme.
Other Remote Options
A Smart TV’s Internet menus can be highly personalized to each owner. To make managing the
menus easier, some Internet TV manufacturers offer users options to supplement operating the
TV via remote control.
Wireless LAN Ready
Provides a wireless network connection for your TV by inserting a USB Wireless LAN Adapter into your TV’s USB port.
Wireless LAN Ready lets you easily access the Internet and your home network with the USB Wireless LAN Adapter UWA-BR100 (as of January 2010). By inserting the USB Wireless LAN Adapter into your TV’s USB port, you can easily create a cable-free network.
Before setting up the wireless LAN function of the TV, be sure to set up a wireless LAN
router.
The USB Wireless LAN Adapter is supplied or available as an optional accessory,
depending on your TV model. In some regions/countries, the USB Wireless LAN Adapter
may not be available.Connecting to Your Wireless LAN
Using the Wireless LAN Ready feature you can connect the TV to your wireless LAN. The set-up procedure differs depending on the type of wireless LAN and wireless LAN router.
Before setting up a wireless LAN, check your wireless LAN environment using the following chart.
Secure wireless LAN?
Do you use a wireless LAN router compatible with Wi-Fi Protected Set-up (WPS)?
YES
NO
(3)
(2)
(1)
(1) Follow the configuration for “Network Set-up” and “Secured Network with Wi-Fi Protected Set-up (WPS)”.
(2) Follow the configuration for “Network Set-up” and “Secured Network without Wi-Fi Protected Set-up (WPS)”.
(3) Follow the configuration for “Network Set-up” and “Unsecured Network with Any Type of Wireless LAN Router”.
Network Set-up
“Network Set-up” helps you configure network settings with the settings wizard. Follow the instructions on the screen.
Press HOME, then select > Network > Network Set-up.
The start-up screen allows you to select a setting procedure according to your network environment.
“View Network Status”: Select to confirm your network status.
“Wired Set-up”: Use to connect to a wired network.
“Wireless Set-up”: Use to connect to a wireless network.
Secured Network with Wi-Fi Protected Set-up (WPS)
The WPS standard makes set-up of a secure wireless home network as straightforward as pressing the WPS button on the wireless LAN router. Before setting up a wireless LAN, check the position of the WPS button on the router and verify how to use it.
1. Select “Wireless Set-up” from the “Network Set-up” start-up screen.2. Select “WPS (Push Button)” for Push Button method or “WPS (PIN)” for PIN
method.3. Follow the instructions that appear on the set-up screen.
To connect to a wireless LAN with WPS, your wireless LAN router needs to support the
WPS standard.Secured Network without Wi-Fi Protected Set-up (WPS)
For setting up a wireless LAN, SSID (wireless network name) and security key (WEP or WPA key) will be required. If you do not know them, consult the instruction manual of your router.
1. Select “Wireless Set-up” from the “Network Set-up” start-up screen.2. Select “Scan”, then select a network from the list of scanned wireless networks.3. Follow the instructions that appear on the set-up screen.Unsecured Network with Any Type of Wireless LAN Router
For setting up a wireless LAN, SSID (wireless network name) will be required. Security key (WEP or WPA key) will not be required because you need to select no security method in this procedure.
1. Select “Wireless Set-up” from the “Network Set-up” start-up screen.2. Select “Scan”, then select a network from the list of scanned wireless networks.3. Follow the instructions that appear on the set-up screen.
BRAVIA™ HD TV (LED & LCD)
Download For KDL-46EX700
System Software Update (Version PKG4.110GAL) For Asia
Article ID:495170(modified 17-Apr-2012)
Applicable Models
Please read all information thoroughly before downloading and installing any files.
What does this download do?
IMPORTANT: This software is only for use with the products identified and sold in Australia, India,
Indonesia, Malaysia,Middle East & Africa, New Zealand, Philippines, Singapore, South Africa, Thailand or
Vietnam. Not all models are sold in all countries.
What does this do?
Sony has designed the BRAVIA® Televisions software update process to be customer friendly. This software
update (version 4.110GAL) provides the following benefits: