How to Install Power CCTV Thermal IP Camera (Bullet) IMPORTANT NOTE: Assuming that the location of the camera has been set the below instructions are to be followed. Hardware Preparation: 1. Check if the package is complete. 2. Inside the box it should have Bullet IP Camera, Screws, installation cd and the Manual. (if it is a wireless Bullet IP camera or a 4G Bullet it should include 2 high gain antenna to be attached on both side) 3. Network cable (UTP Cable Cat 5e) and RJ45 (connectors) used for power and network connection. For Wireless and 4G this will be used for configuration of the IP camera. 4. POE Switch or POE power injector for Wired ONLY.(see Accessories Page for recommended products) 5. DC 12 V power adaptor if POE injector or switch is not available (optional and purchased separately). 6. A ROUTER with an active internet connection. Hardware Installation: 1. First you need to check if the wall or ceiling is safe to drill and to attach the Bullet Camera. 2. Consider the length of the network cable and power cable that will run through the ceiling or wall for both network connection and power source. Measure the approximate size of the network cable or power cable prior to screwing the bullet camera in place. This way you will just connect everything once you find its fixed position. 3. After checking on step 1 and 2 you can proceed with drilling holes for the base of the Bullet camera. You should also consider the wired hole and where it will comfortably fit into the wall or ceiling. 4. Tighten and lock the screws and fix the bracket to where there will be a good view of the area where fire and smoke may occur. 5. Adjust the angle of the bullet camera by losing the screws and finding the right viewing angle of the camera. Once the right angel is found tighten the screws. 6. Once the camera has been attached to the wall or ceiling you need to power it using a POE Switch/POE power injector or a 12V DC power adaptor. (If it’s a wireless Bullet IP camera you will need only 12V DC power adaptor) 7. Connect the cables (network cable/power cable) needed to power up the Bullet camera.
10
Embed
How to Install Power CCTV Thermal IP Camera (Bullet)€¦ · How to Install Power CCTV Thermal IP Camera (Bullet) IMPORTANT NOTE: Assuming that the location of the camera has been
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
How to Install Power CCTV Thermal IP Camera (Bullet)
IMPORTANT NOTE: Assuming that the location of the camera has been set the below instructions are to
be followed.
Hardware Preparation:
1. Check if the package is complete.
2. Inside the box it should have Bullet IP Camera, Screws, installation cd and the Manual. (if it is a
wireless Bullet IP camera or a 4G Bullet it should include 2 high gain antenna to be attached on
both side)
3. Network cable (UTP Cable Cat 5e) and RJ45 (connectors) used for power and network
connection. For Wireless and 4G this will be used for configuration of the IP camera.
4. POE Switch or POE power injector for Wired ONLY.(see Accessories Page for recommended
products)
5. DC 12 V power adaptor if POE injector or switch is not available (optional and purchased
separately).
6. A ROUTER with an active internet connection.
Hardware Installation:
1. First you need to check if the wall or ceiling is safe to drill and to attach the Bullet Camera.
2. Consider the length of the network cable and power cable that will run through the ceiling or
wall for both network connection and power source.
Measure the approximate size of the network cable or power cable prior to screwing the bullet
camera in place. This way you will just connect everything once you find its fixed position.
3. After checking on step 1 and 2 you can proceed with drilling holes for the base of the Bullet
camera. You should also consider the wired hole and where it will comfortably fit into the wall
or ceiling.
4. Tighten and lock the screws and fix the bracket to where there will be a good view of the area
where fire and smoke may occur.
5. Adjust the angle of the bullet camera by losing the screws and finding the right viewing angle of
the camera. Once the right angel is found tighten the screws.
6. Once the camera has been attached to the wall or ceiling you need to power it using a POE
Switch/POE power injector or a 12V DC power adaptor. (If it’s a wireless Bullet IP camera you
will need only 12V DC power adaptor)
7. Connect the cables (network cable/power cable) needed to power up the Bullet camera.