HINIKER AR-2000 SHREDDER 3/13 PART NUMBER 79202348 Rev. C HINIKER AR-2000 SHREDDER PARTS BOOK SECTION 1 PTO SHAFTS SECTION 2 GEARBOX SECTION 3 HITCH ASSEMBLIES SECTION 4 BODY ASSEMBLIES SECTION 5 COMPONENT PARTS SECTION 6 OPTIONAL EQUIPMENT
Page I
HINIKER AR-2000 SHREDDER
3/13
PART NUMBER 79202348 Rev. C
HINIKERAR-2000 SHREDDER
PARTS BOOK
SECTION 1 PTO SHAFTSSECTION 2 GEARBOXSECTION 3 HITCH ASSEMBLIESSECTION 4 BODY ASSEMBLIESSECTION 5 COMPONENT PARTSSECTION 6 OPTIONAL EQUIPMENT
It is the policy of Hiniker Company to constantly improve its products whenever it is practical to do so.
Hiniker Company must therefore reserve the right to redesign or change its equipment or component parts thereof without incurring the obligation to install or furnish such changes on the equipment previously delivered.
INSTRUCTIONS FOR ORDERING PARTS
1. The reference numbers (Ref. No.) in the illustrations correspond to the same refer-ence numbers (Ref. No.) in the description list. An assembly having a part number can be ordered. All other parts must be ordered individually. The quantity in the (Qty.) col-umn is the number of parts used in this area of the machine. The term “A/R” for number required indicates “as required” where the quantity may vary. Order all parts by their part number and description. Do not use the reference number (Ref. No.).
2. All references to left and right, front and rear apply to the machine as viewed from the rear of the machine, facing forward in the direction of travel.
3. Always mention the identification number of the model and serial numbers found on the name plate of the unit on which the part is to be used. Much delay and confusion can be avoided when correct numbers are specified on parts order and correspondence.
HINIKER COMPANY58766 240th St.P.O. BOX 3407
MANKATO, MN 56002-3407 USAPhone: (800) 433-5620
Fax: (800) 637-3991e-mail: [email protected]
PARTSPart Number 79202348 Rev. C March 2013 Parts Books/Hiniker/79202348RevC
Page 1
HINIKER AR-2000 SHREDDER
3/13
SEC
1
SECTION 1PTO SHAFTS
PAGE 2 3-POINT HITCH PTO 1 3/8-21PAGE 3 3-POINT HITCH PTO 1 3/4-20PAGE 4 1 3/8-21 1000 RPM CV PTOPAGE 5 1 3/4-20 1000 RPM CV PTOPAGE 6 OVERRUNNING CLUTCH, 1000 RPM
Page 2
HINIKER AR-2000 SHREDDER
3/13
3-POINT HITCH PTO 1 3/8-21
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
123456789
10
520-03158520-03128520-03124520-03159520-03118520-03134520-03129520-03137520-03135520-03138
Yoke 1 3/8 - 21 SplineCross & Bearing KitSpring Pin 10 x 90Inboard YokeOverrunning Clutch (See Section 1 Page 6)Shield Cone 7 RibBearing RingChainScrewOuter Decal
1211122121
111213141516171819
520-03139520-03136520-03140520-03165520-03162520-03163520-03164520-03141520-03142520-02157
Inner DecalSupport BearingGrease ZerkInner ProfileInboard Yoke OuterOuter Shield TubeInner Shield TubeCollar KitCollar KitComplete PTO Shaft Assembly
111111100
DWG. NO. 2509
SEC
1
520-02157 3-Point PTO Shaft Assembly
Page 3
HINIKER AR-2000 SHREDDER
3/13
3-POINT HITCH PTO 1 3/4-20
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
123456789
10
520-03170520-03128520-03124520-03159520-03165520-03127520-03172520-03118520-03134520-03173
Yoke 1 3/4-20 SplineCross & Bearing KitSpring PinInboard YokeInner ProfileInboard YokeOuter ProfileOverrunning Clutch (See Section 1 Page 6)Shield ConeOuter Shield Tube
1221111121
111213141516171819
520-03174520-03129520-03137520-03135520-03138520-03139520-03136520-03140520-03142520-02159
Inner Shield TubeBearing RingChainScrewDanger DecalDanger DecalSupport BearingGrease ZerkCollar KitComplete 3 Point PTO Assembly
121211112
DWG. NO. 2515
SEC
1
520-02159 3-Point PTO Shaft Assembly
Page 4
HINIKER AR-2000 SHREDDER
3/13
1 3/8-21 1000 RPM CV PTO
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
123456789
1011121314
520-03119520-03120520-0312152003230520-03123520-03124520-03144520-03176520-03127520-03118520-03128520-031295200323152003232
Yoke, 1 3/8-21 SplineDouble YokeGrease ZerkInboard Yoke S4Cross & Bearing KitSpring Pin 10 x 90Inner ProfileProfile & Sleeve WeldmentInboard Yoke S5Overrunning Clutch (See Section 1, Page 6)Cross & Bearing KitBearing RingOut Shield Tube OVLIn Shield Tube Round
11111111111211
1516171819202122232425262728
520032335200323452003235520-03135520-03136520-03137520-03138520-03139520-03140520032365200323752003242520-03142520-03141
CV Cone & Bearing AssemblyShield Cone 4 RibShield Cone 7 RibScrewSupport BearingSafety ChainOuter DecalInner DecalGrease ZerkLubrication DecalCross & Bearing KitSpring Pin 10 x 75Collar Kit (In Item 10)Collar Kit (In Item 1)
11181111111111
DWG. NO. 5936
SEC
1
79202278 PTO 1 3/8-21 GKN 395564
Page 5
HINIKER AR-2000 SHREDDER
3/13
1 3/4-20 1000 RPM CV PTO
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
123456789
1011121314
520-03143520-03120520-0312152003230520-03123520-03124520-03144520-03176520-03127520-03118520-03128520-031295200323152003232
Yoke, 1 3/4-20 SplineDouble YokeGrease ZerkInboard Yoke S4Cross & Bearing KitSpring Pin 10 x 90Inner ProfileProfile & Sleeve WeldmentInboard Yoke S5Overrunning Clutch (See Section 1, Page 6)Cross & Bearing KitBearing RingOut Shield Tube OvalInn Shield Tube Round
11111111111211
15161718192021222324252627
520032335200323452003235520-03135520-03136520-03137520-03138520-03139520-03140520032365200323752003242520-03142
CV Cone & Bearing AssemblyShield Cone 4 RibShield Cone 7 RibScrewSupport BearingSafety ChainOuter DecalInner DecalGrease ZerkLubrication DecalCross & Bearing KitSpring Pin 10 x 75Collar Kit
1118111111112
DWG. NO. 5937
SEC
1
79202277 PTO 1 3/4-20 GKN 396073
Page 6
HINIKER AR-2000 SHREDDER
3/13
OVERRUNNING CLUTCH 1000 RPM
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
12345
520-03146520-03147520-03148520-03149520-03150
Clutch HousingKeyLeaf SpringSupporting RingRetaining Ring
12221
678
520-03151520-03121520-03142520-03118
Hub, 1 3/4 - 20 SplineGrease ZerkCollar KitComplete Overrunning Clutch Assembly
111
DWG. NO. 2512
SEC
1
520-03118 Overrunnig Clutch
Page 2
HINIKER AR-2000 SHREDDER
3/13
GEARBOX ASSEMBLY, 1000 RPM
DWG. NO. 5938
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
123456789
400-17205400-172065010648850106489601-05002601-02075601-05001601-03003650-06056
Casting (Tapped Holes)Casting (Thru Holes)Pinion Shaft/GearCross Shaft/GearBearing Cup (Large) #3720Bearing Cone (Large) #3782Bearing Cup (Small) #25520Bearing Cone (Small) #25581Seal (1 3/4 Shaft)
111111323
10111213141516
702-05093950-011-032203-51156203-51074203-50308601-020017920141251700216
Retaining Ring (1 3/4 Shaft)Socket Head Cap Screw 3/8-16 x 2 1/4Plug, 1/2 NPT Socket Head HexBushing, 1/2 NPT - 1/8 NPTPressure ReliefCone Timken #25580Plug 1/4 NPTGearbox Assembly
11211111
SEC
2
51700216 1000 RPM Gear Box Assembly
Page 1
HINIKER AR-2000 SHREDDER
3/13
SEC
3
SECTION 3HITCH ASSEMBLIES
PAGE 2 TRAIL HITCH ASSEMBLYPAGE 3 3 - POINT HITCH ASSEMBLYPAGE 4 TRAIL HITCH ASSEMBLY 30 FT.
Page 2
HINIKER AR-2000 SHREDDER
3/13
TRAIL HITCH ASSEMBLY
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
123456
035-420657920099379201772031-06459952-001-009951-001-011
Cotter Pin, 1/4 x 1 3/4Hitch PinBar LevelHex Head Cap Screw 1-8 x 3 Gr. 5Lock Washer 1 InchHex Nut 1-8
422222
789
1011
7150517279201776850-001-28585501787850-001-305
Decal, “Warning”Hitch AssemblyTape-Yellow ReflectorDecal, “Caution”Tape-Red Reflector
11111
DWG. NO. 3174
SEC
3
79201775 Trail Hitch Assembly
Page 3
HINIKER AR-2000 SHREDDER
3/13
3-POINT HITCH ASSEMBLYNOT AVAILABLE ON 30 FT. MACHINE
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
123456789
101112
792033262501031979203173117-010-008117-010-009875-001-123890-001-00979200965952-002-0107920099079200964035-42064
3-Point Hitch WeldmentKlik PinLower Pin AssemblySmall SpacerLarger SpacerTop Link PinSpacerSpacer CollarFlat Washer 1 InchPTO Chain AssemblyCenter Link PinCotter Pin 1/4 x 1 1/2
142222122114
1314151617181920212223
7920088079200881034-05172950-001-147792009937920108379201081953-002-021953-005-001850-001-305850-001-28579203325
Top LinkLinkStover Lock Nut 5/8-11Hex Head Cap Screw 5/8-11 x 2 1/2 Gr. 5Lower Trail Hitch PinStand Mount WeldmentStand Tube WeldmentClevis Pin 5/8 x 3 1/2Cotter Pin .120 x 2 3/8Tape Red Reflector (Side Opposite)Tape Yellow Reflector Complete 3-Point Hitch Assembly
12221111111
DWG. NO. 2494A
SEC
3
79203325 3-Point Hitch Assembly
Page 4
HINIKER AR-2000 SHREDDER
3/13
TRAIL HITCH ASSEMBLY 30 FT.
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
123456789
1011
79203529792035458550152785501526950-001-192951-003-010950-001-1210620417920263879203434950-001-200
Trail Hitch Weldment, 30 Ft ARPTO Shaft HolderHitch CTD PPI-331-VHDouble Clevis 1 3/8Hex Head Cap Screw 3/4-10 x 5 1/2 Gr. 5Nut-Nylon Insert 3/4-10Hex Head Cap Screw 1-8 x 6 1/2 Gr. 8Nut-Nylon Insert 1”Mount PlateHose StopHex Head Cap Screw 5/16-18 x 1 1/4 Gr. 5
11111122111
1213141516171819202122
950-002-009951-005-00379203444953-001-007850-001-28585501787850-001-305951-005-064000-0406779203583953-001-010
Hex Head Flange Bolt 3/8-16 x 1Lock Nut 3/8-16 Mac LocCompression SpringCotter Pin 3/16 x 1 1/2 EP Square CutTape-Yellow ReflectorDecal CautionTape-Red ReflectorLock Nut 5/16-18, 2-WayRatchet Jack AssemblyHandle Extension1/4 x 1 1/2 EP Square Cut
22111111111
DWG. NO. 689179203546 Trail Hitch Assembly 30 FT.
SEC
3
Page 1
HINIKER AR-2000 SHREDDER
3/13
SEC
4
SECTION 4BODY ASSEMBLIES
PAGE 2 15, 18, & 20 FT. BODY ASSEMBLYPAGE 4 25 FT. BODY ASSEMBLYPAGE 6 30 FT. BODY ASSEMBLYPAGE 8 ROTOR BEARING 2 3/16” SHAFT
Page 3
HINIKER AR-2000 SHREDDER
3/13
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
123456789
1011
12131415161718192021222324252627282930313233343536373839404142
434445464748495051
000-20179000-20192000-24063952-004-067792023217920232079202318000-64011000-65186000-652237920097679201071000-65627950-003-054031-06113034-05168034-05170034-0517279202337952-001-004035-60063203-51251203-51254400-27039400-340745170021679203223
6040052460400525203-5000371505170792023297920232871504133715-03174850-001-305850-001-2857920302371504126715051717150413171504136792023417920232571505168720-02399953-001-0027920307779203259792008367920086079200866792009117920091379200914
1 3/8 Machinery BushingAdapter Fitting 1/4-28 To 1/8 NPTLock NutFlat Washer 1/2 Inch SAEV-Belt 4 Rib BandedSheave 5VL 15” DiameterCylinder Sheave 5VL 7 1/2” DiameterShield PlateSpring AnchorThreaded HandleFlipper Shield Rod (15 Ft Shredder)Flipper Shield Rod (18 Ft Shredder)Flipper Shield Rod (20 Ft Shredder)Carriage Bolt 3/8-16 x 3/4 Short Shank Gr. 5Hex Head Cap Screw 3/8-16 x 3 Gr. 5Lock Nut 3/8-16 Uni-TorqueLock Nut 1/2-13 Uni-TorqueLock Nut 5/8-11 Uni-Torque“AR-2000” DecalLock Washer 1/2 Inch1/2 x 2 3/4 Woodruff Key45° Elbow Lube Line 1/4-28 To 1/8 NPT45° Elbow 1/8 NPT To 1/8 NPTQ.D. Hub Type “E” 2” BoreJack1000 RPM Gearbox Assembly2” Spherical Bearing W/Lock CollarFlange Bearing 2 3/16” Shaft (See Page 8, Sec 4)Relube Flange W/O FittingRelube Flange W/FittingZerk 1/4-28 NPT StraightWarning DecalWasher 2 3/16 x 10 GaWasher 2 3/16 x 16 GaImportant DecalLift Here DecalTape-Red ReflectorTape-Yellow ReflectorBelt Tension DecalImportant DecalWarning DecalDanger DecalImportant DecalEnd Flipper Shield (18 Ft Shredder)End Flipper Shield (20 Ft Shredder)“Hiniker” Decal3/8 Cable ClampSquare Cut Cotter Pin 1/8 x 1” Rotor Guard WeldmentGrease DecalSplined Coupling W/FittingBearing SupportTake-Up Bar15’ Solid Line Shaft (15 Ft Shredder)18’ Solid Line Shaft (18 Ft Shredder)20’ Solid Line Shaft (20 Ft Shredder)
2A/R45222
A/R24222622
3216284
A/RA/R21144445135123321212224468
A/R222222
5253
5455
5657585960
616263646566676869
707172
73747576777879808182838485868788899091
79200920792009237920337779202287792017947920181879201820792017587920230279200967950-002-02979201793792018177920181979202331792023307150413279201780715041297150516979202299520-031387920325079202336792023357920177979201778792032497920319579203196953-001-01079201037792023047920230379202316792023017920229379201120950-001-111950-001-112950-001-301952-003-006950-001-024950-002-009950-002-010950-002-014950-003-028951-005-003792012137920121879201216
Shield RodBottom Cover (7” Wide Drive Shield)Bottom Cover (8” Wide Drive Shield)Hose Shield RH (Shown)Inside Shield Assembly (15 Ft Shredder)Inside Shield Assembly (18 Ft Shredder)Inside Shield Assembly (20 Ft Shredder)Bearing SupportBelt Idler AssemblyLower Hitch PinHex Head Flanged Whiz Lock Bolt 3/8-16 x 2Outer Shield Assembly (15 Ft Shredder)Outer Shield Assembly (18 Ft Shredder)Outer Shield Assembly (20 Ft Shredder)Shield Spacer 1/16”Shield Spacer 1/8”Warning DecalCylinder LugCaution DecalWarning DecalAR-2000 DecalOuter Decal15’ AR-2000 Body Weldment18’ AR-2000 Body Weldment20’ AR-2000 Body WeldmentRH Line ShieldLH Line ShieldRotor Assembly 5/16 Knife (15 Ft Shredder)Rotor Assembly 5/16 Knife (18 Ft Shredder)Rotor Assembly 5/16 Knife (20 Ft Shredder)Square Cut Cotter Pin 1/4 x 1 1/2Shield Assembly 1000 RpmRH Cover AssemblyLH Cover AssemblyGrease Hose 27 1/2”QD Hub SF Type 2 3/16Hose Shield LHShield BumperHex Head Cap Screw 1/2-13 x 1 1/4 Gr. 5Hex Head Cap Screw 1/2-13 x 2 Gr. 5Hex Head Cap Screw 1/2-13 x 4 1/4 Gr. 5Flat Washer 3/8 Inch SAEHex Head Cap Screw 5/8-11 x 2 1/2 Gr. 8Hex Head Flanged Whiz Lock Bolt 3/8-16 x 1 Hex Head Flanged Whiz Lock Bolt 3/8-16 x 1 1/2Hex Head Flanged Whiz Lock Bolt 3/8-16 x 1 1/4 Carriage Bolt 1/2-13 x 1 1/4Mac Lock Nut 3/8-16Rockshaft Repair Kit 15 Ft.Rockshaft Repair Kit 18 Ft.Rockshaft Repair Kit 20 Ft.
22212222224222
A/RA/R1
A/R12221111122241114214884
486
264
122052111
SEC
4
Page 5
HINIKER AR-2000 SHREDDER
3/13
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
123456789
101112131415161718192021222324252627282930313233343536373839404142434445464748495051
79203071000-20179000-24063715-03174792029367920296579202966000-64011000-65186000-6522379203081950-003-054031-06113034-05168034-05170034-051727920308279203083035-60063950-001-111203-51254400-27039400-340745170021679203223
6040052460400525203-50003951-003-0047920232979202328792030807920288979202868394-002-11579203086792030847920308579202803950-001-284850-001-305720-02399850-001-2857920181979203076792030777920083679200860792008667920307879203115
Housing Weldment 25’1 3/8 Machinery BushingLock NutLift Here DecalV-Belt 5 Rib BandedSheave 5 Groove 15 ODCylinder Sheave 5 Groove 7.5 ODShield PlateSpring AnchorThreaded HandleRod 25’Carriage Bolt 3/8-16 x 3/4 Gr. 5Hex Head Cap Screw 3/8-16 x 3 Gr. 5Lock Nut 3/8-16 Uni-TorqueLock Nut 1/2-13 Uni-TorqueLock Nut 5/8-11 Uni-TorqueRH Bracket GuardLH Bracket Guard1/2 x 2 3/4 Woodruff KeyHex Head Cap Screw 1/2-13 x 1 1/4 Gr. 545o Elbow 1/8 NPT To 1/8 NPTQ.D. Hub Type “E” 2” BoreJack1000 RPM Gearbox Assembly2” Spherical BearingFlange Bearing 2 3/16” Shaft (See Page 8 Sec 4)Relube Flange W/O FittingRelube Flange W/FittingZerk 1/4-28 NPT StraightLock Nut 1/2-20 Fine Thread, NylonWasher 2 3/16 x 16 GaWasher 2 3/16 x 10 GaMid Shield 25’Rotor Shaft WeldmentCoupler, Case HardenedO-RingBearing Support Plate WeldmentRotor Assembly 5’ BalancedRotor Assembly 7’ BalancedFlange Bearing 2 7/16 ShaftHex Head Cap Screw 1/2-13 x 4 3/4 Gr. 5Tape-Red Reflector3/8 Cable ClampTape-Yellow ReflectorOutside Shield AssemblyInside Shield AssemblyRotor Guard WeldmentSplined Coupler W/FittingsBearing SupportTake-Up Bar25’ Splined Line Shaft25’ Shaft (Keyway Both Ends)
12
102222
30242622
664114
24A/R21164665
24A/RA/R24242224834322
1622222
5253
54555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899
7920092079200923792033777920228779202293792017587920307979200967792017807920177879201779792011207920103779202304792023037920231679202301953-001-010953-001-002952-003-006952-004-067952-001-004951-005-003950-003-028950-002-014950-002-010950-002-009950-001-024950-001-301950-001-112792031057920311179203112950-008-0017150412671504131715051717150516879202337520-03138792030237920229971505169715051707150412971504133715041327920325971504136
Shield RodBottom Cover (7” Wide Drive Shield)Bottom Cover (8” Wide Drive Shield)Hose Shield RH (Shown)Hose Shield LHBearing SupportIdler AssemblyLower Hitch PinCylinder LugLH Line ShieldRH Line ShieldShield BumperShield Assembly 1000 RpmRH Cover AssemblyLH Cover AssemblyGrease Hose 27 1/2”QD Hub SF Type 2 3/161/4 x 1 1/2 Square Cut Cotter Pin1/8 x 1” Square Cut Cotter PinFlat Washer 3/8 Inch SAEStandard Flat Washer 1/2 Inch HardenedLock Washer 1/2 InchMac Lock Nut 3/8-16Carriage Bolt 1/2-13 x 1 1/4Hex Head Flanged Whiz Lock Bolt 3/8-16 x 1 1/4Hex Head Flanged Whiz Lock Bolt 3/8-16 x 1 1/2 Hex Head Flanged Whiz Lock Bolt 3/8-16 x 1Hex Head Cap Screw 5/8-11 x 2 1/2 Gr. 8Hex Head Cap Screw 1/2-13 x 4 1/4 Gr. 5Hex Head Cap Screw 1/2-13 x 2 Gr. 5Chain CouplingCoupling 1 3/4 Spline Weldment, Hardened2” Shaft Coupling Weldment, HardenedSocket Head Set Screw 3/8-16 x 3/8 Knurled CupImportant DecalDanger DecalWarning DecalHiniker Decal“AR-2000” DecalOuter DecalBelt Tension DecalAR-2000 DecalWarning DecalWarning DecalCaution DecalImportant DecalWarning DecalGrease DecalImportant Decal
222114222114111
10246898
4932174
2444822241124222222111
A/R2
SEC
4
Page 6
HINIKER AR-2000 SHREDDER
3/13
30 FT BODY ASSEMBLY
DWG. NO.6894
SEC
4
* See Section 5, Page 5 For Hub And Bearing Information.
Page 7
HINIKER AR-2000 SHREDDER
3/13
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
123456789
10111213141516171819202122232425262728293031323334353637383940414243444546474849505152535455565758596061626364656667686970717273747576777879
7920348279203218000-2406379203523792035287920351479203515000-6401179203512000-6522379203503950-003-054031-06113034-05168034-05170034-051727920308279203083035-60063950-001-111203-5125479203525792035245170021679203217792032196040052460400525203-50003951-003-0047920232979202328792035207920288979202868394-002-11579203086792030847920350279202803950-001-28471504132720-0239979203505034-0517579203129792030777920083679200860810045007920349979200920792033777920228779202293792017587920356779200967792017807920351679203580792011207920092579202304792023037920231679202301953-001-010953-001-002952-002-007952-004-067952-001-004951-005-003950-003-028950-002-014950-002-010950-002-009950-001-024950-001-124
Body Weldment 30 Ft. ARFlange Bearing 2” ShaftLock Nut, Grease HoseSpring Cage WeldmentV-Belt Goodyear 6/5VL794Sheave 6 Groove 5V 15 ODSheave 6 Groove 5V 7 1/2 ODShield PlateCompression SpringThreaded HandleFlipper Shield RodCarriage Bolt 3/8-16 x 3/4 Gr. 5 SSHex Head Cap Screw 3/8-16 x 3 Gr. 5Lock Nut 3/8-16 Uni-TorqueLock Nut 1/2-13 Uni-TorqueLock Nut 5/8-11 Uni-TorqueRH Bracket GuardLH Bracket Guard1/2 x 2 3/4 Woodruff KeyHex Head Cap Screw 1/2-13 x 1 1/4 Gr. 545 Degree ElbowQD Bushing Type F 2” BoreTubular Mount Jack1000 RPM Gearbox AssemblyBearing 2” SphericalFlange Bearing 2 3/16” ShaftRelube Flange W/O FittingRelube Flange W/FittingZerk 1/4-28 Tapered Thread StraightLock Nut 1/2-20 NylonWasher 2 3/16 x 16 GaWasher 2 3/16 x 10 GaRod WeldmentRotor Shaft WeldmentCoupler, Case HardenedO-Ring #139-70 Buna-NBearing Support Plate WeldmentRotor Assembly 5’ BalancedOuter Rotor Assembly 10’ BalancedFlange Bearing 2 7/16 ShaftHex Head Cap Screw 1/2-13 x 4 3/4 Gr. 5Decal Warning3/8 Cable ClampLine Shaft Shield AssemblyLock Nut 1-8Wire HolderRotor Guard WeldmentSplined Coupler W/FittingsBearing SupportRingLine Shaft, 30 Ft. ARShield RodBottom CoverHose Shield RH (Shown)Hose Shield LHBearing SupportIdler AssemblyLower Hitch PinCylinder LugHitch Pin, End TransLine Shaft ShieldShield BumperShield 1000 RPMRH Cover AssemblyLH Cover AssemblyGrease Hose 27 1/2”QD Hub SF Type 2 3/16Cotter Pin 1/4 x 1 1/2 Square CutCotter Pin 1/8 x 1” Square CutFlat Washer 5/8Flat Washer 1/2 Standard HardenedLock Washer 1/2Lock Nut 3/8-16 Mac LocCarriage Bolt 1/2-13 x 1 1/4Hex Head Flange Bolt 3/8-16 x 1 1/4Hex Head Flange Bolt 3/8-16 x 1 1/2Hex Head Flange Bolt 3/8-16 x 1Hex Head Cap Screw 5/8-11 x 2 1/2 Gr. 8Hex Head Cap Screw 1/2-13 x 4 Gr. 5
14
102222
36242826
844114
22421144445
24A/RA/R24242224814621
16221222116222124111
102
1084
168
522464
3844
8081828384858687888990919293949596979899
100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158
950-001-112951-001-008950-001-272951-003-0107920357679203518031-06212030-16132955-001-010951-005-064400-11027030-16041715041337150412979203259715-03174520-0313871505171850-001-305850-001-285715051687920233771504126715041317920354871504136952-003-010951-005-089950-001-233792033927920335179203368850-001-39685501557953-001-007792026697920341979203216850-002-669855015377920350779203436792034447920268179202368950-001-097957-001-017956-005-002956-007-02479203549950-001-166034-05173950-001-092792035597920351179203560950-001-12536100000792027257920312836100001956-008-036957-028-0118550153938809034950-001-132060756031-0600679203378956-007-023956-006-002957-001-035956-005-0017920341479203433952-002-010955-001-0027920335279203527
Hex Head Cap Screw 1/2-13 x 2 Gr. 5Hex Nut 5/8Hex Head Cap Screw 3/4-10 x 6 3/4 Gr. 5Nut-Nylon Insert 3/4-10End Trans Hitch WeldmentJack Clevis WeldmentHex Head Cap Screw 1/2-13 x 3 1/4 Gr. 5Carriage Bolt 1/2-13 x 1 1/2 Gr. 5Grease Fitting 1/8-27 NPT 90 DegreeLock Nut 5/16-18 2-WayBracketCarriage Bolt 5/16-18 x 3/4 Gr. 5Decal ImportantDecal CautionDecal GreaseLift Here DecalOuter DecalWarning DecalTape-Red ReflectorTape-Yellow ReflectorHiniker DecalAR-2000 DecalImportant DecalDanger DecalDecal Spring InstallationDecal ImportantFlat Washer 1/4 Inch SAENut 1/4-20 2-Way Gr. AHex Head Cap Screw 1/4-20 x 5/8 Gr. 5Operator Manual CanisterTire & Rim Assembly 9.5L x 15 12 PlyRim 8” x 15, 6 BoltTire ValveCylinder PinPin-Cotter 3/16 x 1 1/2 EP Square CutFront Wheel Leg AssemblyCylinder Stop WeldmentWheel Leg Assembly W/Hub9.5L x 15 Tire 8 PlyTire & Rim Assembly 9.5L 15Rear Wheel Leg Weldment (Does Not Include Hub)LatchCompression SpringPinHydraulic Cylinder 3 x 8Hex Head Cap Screw 5/16-18 x 2 1/2 Gr. 5Hose Assembly 3/8 x 72”Fitting Elbow 90 DegreesFitting Tee 3/4 ORB x 9/16 JICRear Trans Pivot WeldmentHex Head Cap Screw 3/4-10 x 2 Gr. 5Lock Nut 3/4-10 Uni-Torque Gr. BHex Head Cap Screw 3/8-16 x 1 3/4 Gr. 5Rockshaft Bearing CapBracket Pivot ClampBearing Rockshaft End TransHex Head Cap Screw 1/2-13 x 1 1/2 Gr, 5Light, Implement, LH AssemblyLight BracketLight BarLight, Implement, RH AssemblyConnector ISO Male Hydraulic 3/4 ORBHose Assembly 3/8 x 150”Safety Chain 10,000 LbHarness Lighting 30’ WindrowHex Head Cap Screw 5/8-11 x 1 3/4 Gr. 5Nut Lock 5/8-11 Nylon InsertHex Head Cap Screw 1/4-20 x 1 Gr. 5Front WeldmentFitting Tee Bulkhead 9/16 WCFitting Elbow 90 Degrees BulkheadHose Assembly 3/8 x 186”Fitting Elbow 90 Degree 9/16 JIC M x 3/4 ORBHydraulic Cylinder Control SegmentsCylinder Pin ExtendedWasher Flat 1 WRTGrease Fitting 1/4-28Tire 9.5L x 15, 12 PlyWheel Leg Assembly 30 Ft. AR
2441111242
121611
23222332211222
10212
A/RA/R24122
A/R61222444421334226411114411888122462222
SEC
4
Page 1
HINIKER AR-2000 SHREDDER
3/13
SEC
5
SECTION 5COMPONENT PARTS
PAGE 2 KNIFE & ROTOR ASSEMBLYPAGE 3 15, 18, AND 20 FT. IDLER ASSEMBLYPAGE 3 25 FT. IDLER ASSEMBLYPAGE 4 30 FT. IDLER ASSEMBLYPAGE 4 SMV SIGN ASSEMBLYPAGE 5 TIRE, RIM & WHEEL LEG ASSEMBLY
Page 2
HINIKER AR-2000 SHREDDER
3/13
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
1234
7920229079202291950-001-322060756
SS KnifeBushing 3/4”Hex Head Cap Screw 5/8-11 x 2 3/4 Gr. 8Lock Nut 5/8-11 Nylon Insert
A/RA/RA/RA/R
5678
79202889951-003-004394-002-11579202868
Rotor Shaft WeldmentLock Nut 1/2-20 Nylon InsertO-Ring #139-70 Buna-NCoupler Case Hardened
21221
DWG. NO. 5944
KNIFE & ROTOR ASSEMBLY
SEC
5
Page 3
HINIKER AR-2000 SHREDDER
3/13
15, 18, AND 20 FT. IDLER ASSEMBLY
DWG. NO. 5939
DWG. NO. 6480
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
12345
7920308879202935725-03047952-001-005951-005-044
Pivot Idler WeldmentIdler 8 OD x 2” W x 5/8Extension SpringLock Washer 5/8 Med Split SAELock Nut 2-Way 5/8-11
12132
6789
952-003-0038100402579203089950-001-163
Flat Washer 5/8 SAEPivot BushingSpacer Idler CenterHex Head Cap Screw 5/8-11 x 5 1/2 Gr. 5
2111
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
12345
7920230051599031725-03047031-06365951-005-037
Idler Weldment8” Idler PulleyExtension SpringHex Head Cap Screw 3/4-10 x 5Lock Nut 3/4-10 2-Way
11111
6789
10
033-12013400-10466951-001-009952-001-00679202310
Flat Washer 3/4SpacerHex Nut 3/4-10Lock Washer 3/4 InchSpacer 5/16 x 3/4 Conduit
12111
SEC
5
79202302 BT Idler Assembly
25 FT. IDLER ASSEMBLY
79203079 Idler Assembly
Page 4
HINIKER AR-2000 SHREDDER
3/13
SEC
5
2
5
3
4
6
1
SMV SIGN ASSEMBLY
DWG. NO. 2521REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
1234
400-22083 850-001-354031-10599951-001-002
MountSMV EmblemMachine Screw #10-24 x 1/2 Slotted Round HeadHex Nut #10-24
1122
56
033-22007 715-03056 790-41218
Lock Washer #10Caution Decal Complete SMV Sign Assembly
21
790-41218 Assembly SMV And Mount
30 FT. IDLER ASSEMBLY
DWG. NO.6892
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
1234
79203568792035697920357079203571
Idler WeldmentIdler Center Spacer BushingIdlerIdler Outer Spacer Bushing
1122
567
951-005-044203-50003950-001-027
Lock Nut 5/8-11 2-WayGrease Zerk 1/4-28 NPT StraightHex Head Cap Screw 5/8-11 x 6 1/2 Gr. 5
111
79203567 30 Ft. Idler Assembly
Page 5
HINIKER AR-2000 SHREDDER
3/13
DWG. NO. 6893
TIRE, RIM, & WHEEL LEG ASSEMBLY
SEC
5
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
123456789
1011121314
7920321079200827951-001-008952-001-005950-001-023850-001-164850-001-154850-003-053955-001-001950-011-006850-001-153802-000-007951-005-002953-001-017
Wheel Leg Weldment (See Drawing Above)Clamp PlateHex Nut 5/8-11 Lock Washer 5/8 Hex Head Cap Screw 5/8-11 x 2 Gr. 5Triple Lip SealCone JL69349Hub W/Wear Sleeve (Includes 16, 17, 18)Grease Fitting 1/8-27 NPT Wheel Bolt 1/2-20 x 1 Cone LM67048Flat Washer 7/8 InchSlotted Nut 7/8-14Square Cut Cotter Pin 5/32 x 1 1/2
11666111161111
1516171819
2021
2223
850-001-155850-001-159850-001-555850-001-158850-001-82879203368850-001-396805-001-154850-002-66979203513950-001-1417920321679203527
Dust CapRear Cup JL 69310Wear SleeveFront Cup LM 670105” x 15 Rim - 6 Bolt Black (Not Part Of Assembly)Rim 8” x 15”, 6-Bolt (Not Part Of Assembly)Tire Valve (Not Part Of Assembly)7.6 x 15 Tire 8 Ply9.5L x 15 Tire 8 PlySpacerHex Head Cap Screw 5/8-11 x 3 Gr. 5Wheel Leg Assembly (Includes Items 1-18)Wheel Leg Assembly (Includes Items 1-18, 22, 23) 30 Ft. Only
11111111126
Page 1
HINIKER AR-2000 SHREDDER
3/13
SEC
6
SECTION 6OPTIONAL EQUIPMENT
PAGE 2 RATCHET JACK ASSEMBLYPAGE 2 GRASS DIVIDERPAGE 3 MANUAL END TRANSPORT KITPAGE 4 MANUAL HUB & SPINDLE ASSEMBLYPAGE 4 HYDRAULIC CYLINDER STOP BLOCK SETPAGE 5 HYDRAULIC END TRANSPORTPAGE 6 PTO SHAFT HOLDERPAGE 7 SAFETY LIGHTING FIELD USE ONLYPAGE 7 SAFETY LIGHTING END TRANSPORT/FIELD USEPAGE 8 SKID PLATE KITPAGE 9 HYDRAULIC LIFT KIT 15’, 18’, 20’, AND 25’PAGE 10 HYDRAULIC CYLINDER 2 1/2 X 8 CYLINDERPAGE 10 HYDRAULIC CYLINDER 3 X 8 CYLINDER
Page 2
HINIKER AR-2000 SHREDDER
3/13
RACHET JACK ASSEMBLY
DWG. NO. 2502
GRASS DIVIDER
DWG. NO. 3172
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
12
79201851 950-002-013
Grass Divider WeldmentHex Head Flanged Lock Bolt 1/2-13 x 1 1/2
11
34
031-06208 951-005-055
Hex Head Cap Screw 1/2-13 x 2 1/4 Gr. 5Mac Lock Nut 1/2-13
12
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
1 000-04067 Complete Rachet Jack Assembly 1
SEC
6
000-04067 Ratchet Jack Assembly
79201854 Grass Divider Assembly
Page 3
HINIKER AR-2000 SHREDDER
3/13
1
�
�
�
�
�
�
��
�
�
1�
1�
11
11
11 1�
111�
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
123456
792010407920188779200977850-001-309000-20255950-001-246
Transport Tongue AssemblyFront Transport Mount WeldmentRear Transport WeldmentHitch Pin AssemblyClevis Pin AssemblyHex Head Cap Screw 1/2-13 x 7 1/2 Gr. 5
111212
789
101112
950-001-166034-05170034-05173952-003-00479201044850-001-828
Hex Head Cap Screw 3/4-10 x 2 Gr. 5UNI-Torque Lock Nut 1/2 -13 UNI-Torque Lock Nut 3/4-10 SAE Flat Washer 1/2 InchEnd Transport Spindle Assembly (Sec. 6 Page 4)5” x 15” Rim - 6-Bolt
323422
DWG. NO. 3186
MANUAL END TRANSPORT KIT15’ ALL SN
(18’ SN 2001-0011-100 AND BELOW)(20’ SN 2002-0065-100 AND BELOW)
SEC
6
1751 End Transport Kit
Page 4
HINIKER AR-2000 SHREDDER
3/13
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
1234567
79201028850-001-164850-001-154850-003-053955-001-001950-011-006850-001-153
Spindle End TransportTriple Lip SealCone JL69349Hub W/Wear Sleeve (Includes Item 12)Grease Fitting 1/8-27 NPT Wheel Bolt 1/2 - 20 x 1Cone LM67048
1111161
89
101112
802-000-007951-005-002953-001-017850-001-155850-001-55579201044
Washer 7/8 Slotted Nut 7/8-14Square Cut Cotter Pin 5/32 x 1 1/2 Dust CapWear SleeveComplete Spindle Assembly
11111
DWG. NO. 2519
MANUAL END TRANSPORT HUB & SPINDLE ASSEMBLYSEC
6
HYDRAULIC CYLINDER STOP BLOCK SET
DWG. NO. 6857
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
1 79203414 Hydraulic Cylinder Stop Block Set 1
Page 5
HINIKER AR-2000 SHREDDER
3/13
SEC
6REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
123456789
10111213141516171819202122
79202985792026697920335179202987792033887920297879203378792029887920236879203419957-021-001955-001-002956-007-023957-029-00379202989956-003-001921-001-144956-008-03662301179202990950-001-16579202967
Rear Wheel Leg AssemblyFront Wheel Leg AssemblyTire & Rim Assembly 9.5L-15 x 12 PlyWld, Jack ClevisEnd Trans Hitch W/Decal AssemblyRear Transport Pivot WeldmentFront WeldmentBracket, Pivot ClampHydraulic Cylinder 3 x 8 (See Sec 6 Pg 10) LionCylinder StopHose Assembly 1/4 x 54”Grease Fitting 1/4-28Bulkhead Fitting-Tee, 9/16 JICHose Assembly 1/4 x 84”Rockshaft BearingStraight Adapter 9/16 To 3/4 .297 ID14” Plastic Cable TieMale Hydraulic 3/4 ORB Connector ISOLynch Pin 5/16 x 2 3/4Rockshaft Bearing CapHex Head Cap Screw 5/8-11 x 7 1/2 Gr. 5Hitch Pin
1121111222422264825231
23242526272829303132333435363738394041424344
950-001-152060756034-05173950-001-097951-005-03679202681950-001-092951-005-051950-001-125950-001-023950-001-166034-05170921-001-490921-001-48779203524400-11027030-1604185501557953-001-007792034447920343679202686
Hex Head Cap Screw 3/4-10 x 6 Gr. 5Lock Nut 5/8-11 Nylon InsertLock Nut 3/4-10 Gr. B Uni-TorqueHex Head Cap Screw 5/16-18 x 2 1/2 Gr. 5Lock Nut 5/16-18 Mac LocPinHex Head Cap Screw 3/8-16 x 1 3/4 Gr. 5Lock Nut 3/8-16 2 WayHex Head Cap Screw 1/2-13 x 1 1/2 Gr. 5Hex Head Cap Screw 5/8-11 x 2 Gr. 5Hex Head Cap Screw 3/4-10 x 2 Gr. 5Lock Nut 1/2 Gr. B StoverGreen Cable TieRed Cable TieTubular Mount Jack 10” TravelBracketCarriage Bolt 5/16-18 x 3/4 Gr. 5Cylinder PinPin-Cotter 3/16 x 1 1/2 EP Square CutCompression SpringLatchCylinder Stop
1544824442348811224222
DWG. NO. 6858
HYDRAULIC END TRANSPORT KIT(18’ SN 2001-0012-101 AND UP)(20’ SN 2002-0066-101 AND UP)(25’ SN 2003-0001-101 AND UP)
For Bearing Info See Section 5, Page 579202993 Hydraulic End Transport Kit
Page 6
HINIKER AR-2000 SHREDDER
3/13
SEC
6
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
12345678
950-003-012951-005-051952-001-004952-004-067951-005-0367920274079202638031-06110
Carriage Bolt 3/8-16 x 2 1/4 Gr. 5Lock Nut 3/8-16 2-WayLock Washer 1/2 InchFlat Washer 1/2 InchLock Nut 5/16-18 Mac LocPTO HolderMount PlateHex Head Cap Screw 3/8-16 x 2 1/4 Gr. 5
13221112
9101112131415
792026397920343479203444950-001-200950-001-13579202739953-005-001
PTO HolderHose StopCompression SpringHex Head Cap Screw 5/16-18 x 1 1/4 Gr. 5Hex Head Cap Screw 1/2-13 x 2 3/4 Gr. 5PinHair Pin
1111211
DWG. NO. 6382
PTO HOLDER
Page 7
HINIKER AR-2000 SHREDDER
3/13
SEC
6
SAFETY LIGHTING FIELD USE ONLY
DWG. NO. 5940
END TRANSPORT/FIELD USE SAFETY LIGHTING PACKAGE
DWG. NO. 6506
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
12345
7920312479203125400-1102738809035367-001-014
Light Assembly LeftLight Assembly RightBracketLighting HarnessCable Tie, Black 8 Inch
1111
20
6789
030-1604179203129951-005-03679203128
Carriage Bolt 5/16-18 x 3/4 Gr. 5Wire HolderMac Lock Nut 5/16-18Long Light Bar
6161
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
1234
36100000361000013880902879202294
Light, Implement, LH AssemblyLight, Implement, RH AssemblyHarness, LightingLight Bracket
1112
567
367-001-014031-06006951-005-089
Cable Tie, Black 8 InchHex Head Cap Screw 1 /4-20 x 1 Gr. 5Lock Nut 1/4-20, 2-Way
1288
79203126 Safety Light Package
Page 8
HINIKER AR-2000 SHREDDER
3/13
SEC
6
SKID PLATE KIT
DWG. NO. 5941
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
12
79202281950-001-029
Skid WeldmentHex Head Cap Screw 3/4-10 x 1 3/4 Gr. 5
28
3 951-005-097 Lock Nut 3/4-10 Mac-Lock 8
79202306 Skid Plate Kit
Page 9
HINIKER AR-2000 SHREDDER
3/13
SEC
6
HYDRAULIC LIFT KIT 18’, 20’, AND 25’
DWG. NO. 5943
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
123
79202351956-003-001957-022-014957-022-017
Hydraulic Cylinder 2 1/2 x 8 (See Sec 6 Pg 10)Straight Adapter 9/16 M To 3/4 M .297IDHose Assembly 1/4 x 126” (18’ & 20’)Hose Assembly 1/4 x 156” (25’)
2444
4567
956-007-023957-028-011956-008-036921-001-144
Fitting-Tee Bulkhead 9/16 JICHose Assembly 3/8 x 150”Connector ISO Male Hydraulic 3/4 ORB14” Plastic Cable Tie
2228
79202349 Hydraulic Lift Kit 18’ and 20’79203021 Hydraulic Lift Kit 25’
HYDRAULIC LIFT KIT 15’
DWG. NO. 6531
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
12
79202368956-005-001
3 x 8 Cylinder Assembly (See Sec. 6, Page 10)90° Elbow
12
34
957-004-006 957-004-007
Hose Assembly 3/8 x 156” Hose Assembly 3/8 x 172”
11
79201616 Hydraulic Cylinder Package
Page 10
HINIKER AR-2000 SHREDDER
3/13
SEC
6
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
1 79202366 Seal Kit 1 2 79202351 2 1/2 x 8 Cylinder Assembly
2 1/2 X 8 CYLINDER
DWG. NO. 656779202351 2 1/2 x 8 Cylinder
REF.NO.
PARTNUMBER DESCRIPTION QTY. REF.
NO.PART
NUMBER DESCRIPTION QTY.
1 79202380 Seal Kit 1 2 79202368 3 x 8 Cylinder Assembly
3 X 8 CYLINDER
DWG. NO. 594979202368 3 x 8 Cylinder