Submission folder Customer Hotline Customer Hotline Hong Kong 8228 8118 Macau (Toll free) 00800- 8228 8118 Hilti HIT-RE500-SD Injection Adhesive with HIT-V Sample Submission and 2 - 5 Approval Form Product Information 6 - 1 Technical Information 1 - VOC Content Test Certificate (LEED) Country of Origin - Material Safety Data Sheet Government Letter 7 - 3 4 - 5 36 - 38 Page 1 May 2016
38
Embed
Hilti HIT-RE500-SD Injection Adhesive with HIT-V · Hilti HIT-RE500-SD Injection Adhesive with HIT-V ... The enclosed sample and catalogue* / certificate of origin* / technical data*
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Submission folder
Customer Hotline Customer Hotline Hong Kong 8228 8118Macau (Toll free) 00800- 8228 8118
To: Contract Manager’s Representative Attention: ________________________
From: ________________________________
The enclosed sample and catalogue* / certificate of origin* / technical data* / test report* / job reference* as described below have been checked for compliance with the Specifications and Drawings, and are submitted for approval.
1. General Information a. Material Description HIT – RE500-SD Injection Adhesive __________________________________________________________ __________________________________________________________ b. Location: __________________________________________________________ __________________________________________________________ __________________________________________________________ c. Specification Ref. Page: __________________________ Item: _______________________ __________________________ _______________________ __________________________ _______________________ d. Drawing Ref. No. __________________________________________________________ __________________________________________________________ __________________________________________________________ e. B.Q. Ref.No.: __________________________________________________________ __________________________________________________________ __________________________________________________________ f. Anticipated date of approval: __________________________________________________________
2. Technical Information The submitted sample has been checked against the specification and drawings as listed below:-
Specification Requirements Submitted Sample (State details against each item)
a. Brand Not specified Hilti b. Country of Origin Not specified Germany c. Manufacturer’s Name & Address Not specified Hilti Corporation, FL-9494 Principality of Liechtenstein.
d. Factory’s Name & Address(es) Not specified Hilti Gmbh Ind. Ges. F. Befestigungstechnik Hiltistrasse 6, D-86916 Kaufering, Germany. e. Supplier (with Applicator, if any) Not specified Hilti (Hong Kong) Ltd
Page 2 May 2016
Page 2 of 2
f. Appearance Not specified According to the sample submitted
g. Color + Not specified Red
h. Specification Not specified Attached
i. Manufacturer’s Catalogue Not specified Attached
j. Test Report (Original/Certificated True Copy) Not specified Attached
k. Previous Job Reference Not specified Attached
l. Supplementary Information Not specified NIL
For and on behalf of the Contractor
____________________________ (Quality Control Manager)
On the basis of the sample and information given, the above sample submitted is:
(1) * Approved. (2) * Not approved because ____________________________________________________ _______________________________________________________________________ _______________________________________________________________________ Remarks: _______________________________________________________________________ _______________________________________________________________________ _______________________________________________________________________
Approval does not alter the requirements of the Contract Contract Manager’s Representative: ____________________________
_____________________________ Date:
cc. _______________________________________ _______________________________________ _______________________________________ _______________________________________
(* Delete if appropriate) (+ For glass or vitreous mosaic tiles, the contractor is required to confirm the colour range(s) of the submitted sample, i.e. a) light and or medium; or b) dark)
To: Contract Manager’s Representative Attention: ________________________
From: ________________________________
The enclosed sample and catalogue* / certificate of origin* / technical data* / test report* / job reference* as described below have been checked for compliance with the Specifications and Drawings, and are submitted for approval.
1. General Information a. Material Description HIT-V / HIT-VR Anchor Rod __________________________________________________________ __________________________________________________________ b. Location: __________________________________________________________ __________________________________________________________ __________________________________________________________ c. Specification Ref. Page: __________________________ Item: _______________________ __________________________ _______________________ __________________________ _______________________ d. Drawing Ref. No. __________________________________________________________ __________________________________________________________ __________________________________________________________ e. B.Q. Ref.No.: __________________________________________________________ __________________________________________________________ __________________________________________________________ f. Anticipated date of approval: __________________________________________________________
2. Technical Information The submitted sample has been checked against the specification and drawings as listed below:-
Specification Requirements Submitted Sample (State details against each item)
a. Brand Not specified Hilti b. Country of Origin Not specified Republic of China c. Manufacturer’s Name & Address Not specified Hilti Corporation, FL-9494 Principality of Liechtenstein.
d. Factory’s Name & Address(es)
Not specified Hilti (China Zhangjiang) Co. Ltd., Yongping Road South, Zhangjiang Development Zone, 524022 Zhangjiang, Guangdong Province, China.
e. Supplier (with Applicator, if any)
Page 4 May 2016
Page 2 of 2
Not specified Hilti (Hong Kong) Ltd
f. Appearance Not specified According to the sample submitted
g. Color + Not specified Nil
h. Specification Not specified Attached
i. Manufacturer’s Catalogue Not specified Attached
j. Test Report (Original/Certificated True Copy) Not specified Attached
k. Previous Job Reference Not specified Attached
l. Supplementary Information Not specified NIL
For and on behalf of the Contractor
____________________________ (Quality Control Manager)
On the basis of the sample and information given, the above sample submitted is:
(1) * Approved. (2) * Not approved because ____________________________________________________ _______________________________________________________________________ _______________________________________________________________________ Remarks: _______________________________________________________________________ _______________________________________________________________________ _______________________________________________________________________
Approval does not alter the requirements of the Contract Contract Manager’s Representative: ____________________________
_____________________________ Date:
cc. _______________________________________ _______________________________________ _______________________________________
(* Delete if appropriate) (+ For glass or vitreous mosaic tiles, the contractor is required to confirm the colour range(s) of the submitted sample, i.e. a) light and or medium; or b) dark)
Page 5 May 2016
180
Anchor Systems
Customer Hotline: Hong Kong 8228 8118 Macau 00800 8228 8118
HIT-RE 500-SD/500/1 1x Foil pack, 1x Mixer, 1x Mixer extension 1 pc 3870931) This is a non-stock item. For detailed lead time information please contact your Hilti representative.
Injectable mortar HIT-RE 500-SD
Applications■ Structural connections with post-installed rebar (e.g. extension/
beams, etc.)■ Special applications requiring electrical isolation such as fasten-
ing emergency escape handrails in tunnels■ Structural renovation of buildings, bridges and other civil struc-
tures, retrofitting and re-strengthening of concrete members possible
■ Substitution of misplaced / missing rebars or couplers■ Suitable for underwater applications in hammer-drilled holes
(ICC-ESR)
Advantages■ Suitable for use in cracked and uncracked concrete with all
anchoring elements■ Seismic approval for use in seismic applications■ Suitable for anchoring in diamond-cored holes (ICC-ESR)■ High performance and technical superiority as per international
approvals■ No expansion forces in concrete allow secure fastenings even
close to edges and/or with close spacing■ Virtually odourless hence convenient to work with
Base materials ◾ Concrete (cracked) ◾ Concrete (uncracked)
Technical dataMaterial composition Epoxy adhesive
Tested/approved for diamond drilling Yes
Seismic Yes
In-service temperature – range -40 - 70 °C
IBC compliance IBC 2003,IBC 2006,IBC 2009
Additional product information Always wear eye protection and gloves while handling
These are abbreviated instructions which may vary according to the application. Always observe/follow the instructions accompanying the product or refer to www.hilti.com/techlib.
Page 6 May 2016
189
Anchor Systems
Hilti online: www.hilti.com.hk
Ordering designation Anchor size Drill bit diameter Base plate clearance holeSales pack quantity
Item number
HIS-RN M8X90 A4 M8 14 mm 9 mm 10 pc 2580241)
HIS-RN M10X110 A4 M10 18 mm 12 mm 10 pc 258025
HIS-RN M12X125 A4 M12 22 mm 14 mm 5 pc 258026
HIS-RN M16X170 A4 M16 28 mm 18 mm 5 pc 2580271)
HIS-RN M20X205 A4 M20 32 mm 22 mm 5 pc 2580281)
1) This is a non-stock item. For detailed lead time information please contact your Hilti representative.
ApprovalsETA (ETAG 001-05, Option 7)Approvals and test reports may apply to selected products only. Please refer to the documents for details.
Technical dataHead configuration Inner thread
Material composition Steel, 5.8 grade, zinc-plated (min. 5 µm)
Material, corrosion Steel, zinc-plated
Anchor type Internally threaded
Approvals / test reports ETA
Fire Yes
Base materials ◾ Concrete (uncracked)
Page 7 May 2016
183
Anchor Systems
Hilti online: www.hilti.com.hk
Ordering designation WeightSales pack quantity
Item number
HDE 500 CB DISPENSER KIT 1 pc 34990781)
HDE 500-A22 box 2.2 kg 1 pc 2005630
HDE 500-A22 CR/CB cas 2.2 kg 1 pc 2005637
HDE 500-A22 empty 2.4 kg 1 pc 4347241) This is a non-stock item. For detailed lead time information please contact your Hilti representative.
Dispenser HDE 500-A22
Applications■ Injection of Hilti HIT adhesive mortar for fastening anchor rods
and rebars in concrete and masonry ■ No need for external power source supply■ Serial fastenings and/or injection in deep holes
Advantages■ Dose adjustment knob for accurate and controlled dispensing■ Fast, easy foil pack loading■ High battery capacity (up to 100x500ml foil packs)
Technical dataDispenser, setting tool, accessory, tester type
Dispensers
Ordering designation WeightSales pack quantity
Item number
HDM 330 CB DISPENSER KIT 1 pc 34990821)
HDM 330 CB CARDBOARD BOX 1 pc 34991031)
HDM 500 CB DISPENSER KIT (2060870 W/ACC) 1 pc 3499081
HDM 330 cas 1 pc 2060429
HDM 500 cas 1 pc 2060870
HDM 330 box 1.5 kg 1 pc 2005640
HDM 500 box 1.8 kg 1 pc 20056411) This is a non-stock item. For detailed lead time information please contact your Hilti representative.
Dispenser HDM
Applications■ Injection of Hilti HIT adhesive mortar for fastening anchor rods
and rebars in concrete and masonry
Advantages■ Fast, easy foil pack loading
Technical dataDispenser, setting tool, accessory, tester type
Dispensers, n/a
Page 8 May 2016
104
Drilling and Demolition
4
Ordering designation Diameter Working length LengthSales pack quantity
Item number
TE-YD 16/59 16 mm 400 mm 590 mm 1 pc 2018956
TE-YD 18/59 18 mm 400 mm 590 mm 1 pc 2018957
TE-YD 20/59 20 mm 400 mm 590 mm 1 pc 2018959
TE-YD 22/59 22 mm 400 mm 590 mm 1 pc 2018960
TE-YD 25/59 25 mm 400 mm 590 mm 1 pc 2018962
TE-YD 28/59 28 mm 400 mm 590 mm 1 pc 2018964
TE-YD 32/59 32 mm 400 mm 590 mm 1 pc 2018966
Hammer drill bit TE-YD
Applications■ Drilling holes for anchoring structural steel connections (e.g.
steel columns, beams)
Advantages■ Drilling and hole cleaning in one step
Customer Hotline: Hong Kong 8228 8118 Macau 00800 8228 8118
Ordering designation Diameter Working length LengthSales pack quantity
Item number
TE-CD 12/33 12 mm 200 mm 330 mm 1 pc 2018940
TE-CD 14/37 14 mm 240 mm 360 mm 1 pc 2018942
TE-CD 16/37 16 mm 240 mm 360 mm 1 pc 2018945
TE-CD 18/37 18 mm 240 mm 360 mm 1 pc 2018946
Hammer drill bit TE-CD
Applications■ Drilling holes for structural connections with post-installed
rebars
Advantages■ Drilling and hole cleaning in one step
Page 9 May 2016
TSANTER
Typewritten Text
TSANTER
Typewritten Text
TSANTER
Typewritten Text
TSANTER
Typewritten Text
TSANTER
Typewritten Text
TSANTER
Typewritten Text
TSANTER
Typewritten Text
TSANTER
Typewritten Text
TSANTER
Typewritten Text
243
Anchor Systems
Hilti online: www.hilti.com.hk
Ordering designationSales pack quantity
Item number
Blow-out pump 1 pc 60579
Extension tube HIT-VL 16/0.7 10 pc 336646
Accessories for blowing out drilled holes Hilti HIT
Applications■ For fast and efficient removal of dust and debris from drilled
holes of varying diameters and depths to allow correct installa-tion of anchors and rebar
Technical dataDispenser, setting tool, accessory, tester type
VC 40-U 110V 1x Univ. vacuum cleaner VC 40-U 110 V 1 pc 2183451)
VC 40-U 230V 1x Univ. vacuum cleaner VC 40-U 230 V 1 pc 2123001) This is a non-stock item. For detailed lead time information please contact your Hilti representative.
Universal vacuum cleaner VC 40-UM
Technical dataContainer capacity 36 l
Dust capacity 40 kg
Water capacity 25 l
A-weighted emission sound pressure level acc. to EN 60745
71 dB (A)
Hose diameter 36 mm
Hose length 5000 mm
Weight according to EPTA Procedure 01/2003
14.7 kg
Dimensions (LxWxH) 505 x 380 x 610 mm
Applications■ Removing dust from drilling, slitting, grinding, cutting and dry
coring■ Removing slurry from wet coring and cleaning
Advantages■ Hilti AirBoost filter technology for consistently high suction
performance■ Very good handling thanks to compact design■ Full exploitation of tank capacity due to placement of filter and
hose connection in the upper part of the machine■ Robust housing to withstand the harshest jobsite conditions■ New tank concept for easy and virtually dust-free dust removal■ Maximum total load of dust: up to 40 kg
Supplier: Hilti Entwicklungsgesellschaft mbH BU Chemical Anchors Hiltistrasse 6 86916 Kaufering GERMANY
Sample Description: Hilti HIT-RE 500-SD
Date tested: May 2009
Test Method: SCAQMD method 304-91 Determination of Volatile Organic Compounds (VOC) in Various Materials as referenced by South Coast Air Quality Management District (SCAQMD) Rule 1168. The values also comply with the requirements of EPA test method #24.
Test Data:
Specification Product
LEED 2009 (LEED 3.0) LEED 2.2
IEQ-4.1: Low-Emitting Materials – Adhesives and Sealants Hilti
HIT-RE 500-SD Green Building Council of Australia Green Star Office Design 3.0, IEQ-13 Green Star Office Design 2.0, IEQ-13 Green Star Office Interiors 1.1, IEQ-11
Multipurpose Construction Adhesives; VOC Limit: 70 g/L Product contains: 4 g/L of VOC
William Welbes Vice President of Laboratory Operations
Allen Noreen, Ph.D. Technical Director
Page 24 May 2016
Page 25 May 2016
Page 26 May 2016
Page 1/7
Safety data sheetaccording to 1907/2006/EC, Article 31
Printing date 09.06.2011 Revision: 09.06.2011Version number 6
DR
1 Identification of the substance/mixture and of the company/undertaking
· Product identifier
· Trade name: Hilti HIT-RE 500-SD· Container size 330 ml, 500 ml, 1400 ml· Relevant identified uses of the substance or mixture and uses advised against· Application of the substance / the preparation Adhesive mortar for rebar and anchor fastenings in solid concrete
· Details of the supplier of the safety data sheet· Manufacturer/Supplier:Hilti Asia Ltd.17/F, Tower 6China Hong Kong City33 Canton RoadHK-Tsimshatsui, KowloonHong KongTel +852 27734 700Fax +852 2356 7311
· Informing department: see section 16· Emergency telephone number:Hilti Asia Ltd.Tel +852 27734 700Fax +852 2356 7311
2 Hazards identification
· Classification of the substance or mixture
· Classification according to Directive 67/548/EEC or Directive 1999/45/EC· Information concerning particular hazards for human and environment:The product has to be labelled due to the calculation procedure of the "General Classification guideline for preparations of the EU" in thelatest valid version.
· Classification system:The classification is in line with current EC lists. It is expanded, however, by information from technical literature and by informationfurnished by supplier companies.
· Label elements
· Labelling according to EU guidelines:The product has been classified and labelled in accordance with EC Directives / Ordinance on Hazardous Materials (GefStoffV)
· Risk phrases:35 Causes severe burns.41 Risk of serious damage to eyes.20/22 Harmful by inhalation and if swallowed.43 May cause sensitisation by skin contact.51/53 Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
· Safety phrases:1/2 Keep locked up and out of the reach of children.23 Do not breathe fumes.51 Use only in well-ventilated areas.24/25 Avoid contact with skin and eyes.36/37/39 Wear suitable protective clothing, gloves and eye/face protection.26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.28 After contact with skin, wash immediately with plenty of water and soap.61 Avoid release to the environment. Refer to special instructions/safety data sheets.
· Special labelling of certain preparations:Contains epoxy constituents. See information supplied by the manufacturer.
· Other hazards· Results of PBT and vPvB assessment· PBT: Not applicable.· vPvB: Not applicable.
(Contd. on page 2) HK
Page 27 May 2016
Page 2/7
Safety data sheetaccording to 1907/2006/EC, Article 31
Printing date 09.06.2011 Revision: 09.06.2011Version number 6
Trade name: Hilti HIT-RE 500-SD
(Contd. of page 1)
DR
· Additional information:
Hilti HIT
· Information pertaining to particular dangers for man and environment: AR 36/38 Irritating to eyes and skinR 43 May cause sensitisation by skin contactR 51/53 Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment
· Information pertaining to particular dangers for man and environment: BR 35 Causes severe burnsR 41 Risk of serious damage to eyesR 43 May cause sensitization by inhalation and skin contactR 20/22 Harmful on inhalation and if swallowedR 52/53 Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment
Mixture of the substances listed below with harmless additions.
· Dangerous components:
CAS: 1477-55-0EINECS: 216-032-5
m-Xylylenediamine C R35; Xn R20/22; Xi R43
R52/53
25-40%
CAS: 25068-38-6NLP: 500-033-5
reaction product: bisphenol-A-(epichlorhydrin) epoxy resin(number average molecular weight = 700)
Xi R36/38; Xi R43; N R51/53
25-50%
CAS: 28064-14-4 Reaction product: bisphenol-F epichlorhydrin resin, MW 700 Xi R36/38; Xi R43; N R51/53
10-30%
CAS: 16096-31-4EINECS: 240-260-4
1,6-bis(2,3-epoxypropoxy)hexane Xi R36/38; Xi R43
R52/53
10-25%
CAS: 30499-70-8 Trimethylolpropane, (chloromethyl)oxirane polymer Xi R36/38; Xi R43
R52/53
2,5-10%
CAS: 14808-60-7EINECS: 238-878-4
Quartz (SiO2) 25-50%
· Dangerous components A:
CAS: 25068-38-6NLP: 500-033-5
reaction product: bisphenol-A-(epichlorhydrin) epoxy resin(number average molecular weight = 700)
Xi R36/38; Xi R43; N R51/53
CAS: 28064-14-4 Reaction product: bisphenol-F epichlorhydrin resin, MW 700 Xi R36/38; Xi R43; N R51/53
CAS: 16096-31-4EINECS: 240-260-4
1,6-bis(2,3-epoxypropoxy)hexane Xi R36/38; Xi R43
R52/53
CAS: 30499-70-8 Trimethylolpropane, (chloromethyl)oxirane polymer Xi R36/38; Xi R43
R52/53
CAS: 14808-60-7EINECS: 238-878-4
Quartz (SiO2)
· Dangerous components B:
CAS: 1477-55-0EINECS: 216-032-5
m-Xylylenediamine C R35; Xn R20/22; Xi R43R52/53
CAS: 14808-60-7EINECS: 238-878-4
Quartz (SiO2)
· Additional information For the wording of the listed risk phrases refer to section 16. HK
(Contd. on page 3)
Page 28 May 2016
Page 3/7
Safety data sheetaccording to 1907/2006/EC, Article 31
Printing date 09.06.2011 Revision: 09.06.2011Version number 6
Trade name: Hilti HIT-RE 500-SD
(Contd. of page 2)
DR
4 First aid measures
· Description of first aid measures· General information Instantly remove any clothing soiled by the product.· After inhalationTake affected persons into the open air and position comfortablySeek medical treatment in case of complaints.
· After skin contact Instantly wash with water and soap and rinse thoroughly. If skin irritation persist, call a physician.· After eye contactCall a doctor immediately.Rinse opened eye for several minutes under running water.Protect unharmed eye.If splashed into the eyes, seek immediate treatment from an eye doctor or clinic.
· After swallowingDo not induce vomiting; immediately call for medical help.Rinse out mouth and then drink plenty of water.
· Information for doctor· Most important symptoms and effects, both acute and delayed Allergic reactions
5 Firefighting measures
· Extinguishing media· Suitable extinguishing agents Water spray, carbon dioxide (CO2), carbon dioxide blanket, foam, or dry powder.· For safety reasons unsuitable extinguishing agents Water with full jet.· Special hazards arising from the substance or mixtureCan be released in case of fireNitrogen oxides (NOx)Carbon monoxide (CO)Under certain fire conditions, traces of other toxic gases cannot be excluded.
· Advice for firefighters· Protective equipment: In the event of fire, wear self contained breathing apparatus· Additional information Dispose of fire debris and contaminated fire fighting water in accordance with official regulations.
* 6 Accidental release measures
· Personal precautions, protective equipment and emergency proceduresWear protective equipment. Keep unprotected persons away.Wear protective clothing.Use personal protective equipment. Ensure adequate ventilation. Remove all sources of ignition.
· Environmental precautions:Do not allow product to reach sewage system or water bodies.Do not allow to enter the ground/soil.
· Methods and material for containment and cleaning up:Collect mechanically.Clean the accident area carefully; suitable cleaners are:organic solventEnsure adequate ventilation.Dispose of contaminated material as waste according to item 13.
· Reference to other sectionsSee Section 7 for information on safe handlingSee Section 8 for information on personal protection equipment.See Section 13 for information on disposal.
7 Handling and storage
· Handling· Precautions for safe handlingThe usual precautionary measures should be adhered to general rules for handling chemicals.Use only in well ventilated areas.Take note of emission threshold.Check the expiry date: see imprint on manifold (month/year). Do not use expired mortar!
· Information about protection against explosions and fires: Keep ignition sources away - Do not smoke.
· Conditions for safe storage, including any incompatibilities· Storage· Requirements to be met by storerooms and containers: Keep in a cool, dry and dark place; 5 °C to 25 °C.· Information about storage in one common storage facility: Store away from foodstuffs.· Further information about storage conditions: Protect from heat and direct sunlight.
· Storage classAs per VCI (1991) storage classification concept.
(Contd. on page 4) HK
Page 29 May 2016
Page 4/7
Safety data sheetaccording to 1907/2006/EC, Article 31
Printing date 09.06.2011 Revision: 09.06.2011Version number 6
Trade name: Hilti HIT-RE 500-SD
(Contd. of page 3)
DR
8A
8 Exposure controls/personal protection
· Control parameters· Components with limit values that require monitoring at the workplace:The product does not contain any relevant quantities of materials with critical values that have to be monitored at the workplace.
· Additional information: The lists that were valid during the compilation were used as basis.
· Exposure controls· Personal protective equipment· General protective and hygienic measuresThe usual precautionary measures should be adhered to general rules for handling chemicals.Do not eat, drink or smoke while working.Do not inhale gases / fumes / aerosols.Avoid contact with the eyes and skin.Use skin protection cream for preventive skin protection.Clean skin thoroughly immediately after handling the product.Ensure that washing facilities are available in the work place.Do not carry cleaning cloths impregnated with the product in trouser pockets.Keep away from foodstuffs, beverages and food.Take off immediately all contaminated clothingStore protective clothing separately.Wash hands during breaks and at the end of the work.
· Breathing equipment:Not necessary if room is well-ventilated.In case of brief exposure or low pollution use breathing filter apparatus. In case of intensive or longer exposure use breathing apparatusthat is independent of circulating air.
· Recommended filter device for short term use: Filter AX· Protection of hands:Protective glovesAvoid direct contact with the chemical/ the product/ the preparation by organizational measures.Use gloves of stable material (e.g. Nitrile) - if necessary tricoted to improve the wearability.The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.Only use chemical-protective gloves with CE-labelling of category III.
· Material of glovesNitrile rubber, NBRThe selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturerto manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advanceand has therefore to be checked prior to the application.
· Penetration time of glove materialThe exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed.
· As protection from splashes gloves made of the following materials are suitable: Nitrile rubber, NBR· Not suitable are gloves made of the following materials:Natural rubber, NRLeather glovesStrong gloves
· Change in conditionMelting point/Melting range: Not determinedBoiling point/Boiling range: > 200°C
(Contd. on page 5) HK
Page 30 May 2016
Page 5/7
Safety data sheetaccording to 1907/2006/EC, Article 31
Printing date 09.06.2011 Revision: 09.06.2011Version number 6
Trade name: Hilti HIT-RE 500-SD
(Contd. of page 4)
DR
· Flash point: >100°C (DIN 53213)
· Self-inflammability: Product is not selfigniting.
· Danger of explosion: Product is not explosive.
· Vapour pressure at 20°C: 0,04 hPa
· Density at 20°C 1,47 g/cm³ (DIN 51757)
· Solubility in / Miscibility withWater: Unsoluble
· Viscosity:dynamic at 20°C: 50 Pa.s (DIN 53788)kinematic at 20°C: >20 s (DIN 53211/4)
· Solvent content:Organic solvents: 0 %Water: 0 %
10 Stability and reactivity
· Reactivity· Chemical stability· Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.· Possibility of hazardous reactions No dangerous reactions known· Hazardous decomposition products: No dangerous decomposition products known
11 Toxicological information
· Information on toxicological effects· Acute toxicity:· Primary irritant effect:· on the skin: Strong caustic effect on skin and mucous membranes.· on the eye:Strong caustic effect.Strong irritant with the danger of severe eye injury.
· Sensitization: Sensitization possible by skin contact.· Additional toxicological information:The product shows the following dangers according to the calculation method of the General EC Classification Guidelines for Preparationsas issued in the latest version:HarmfulCorrosiveIrritant
12 Ecological information
· Toxicity· Acquatic toxicity: No further relevant information available.· Ecotoxical effects:· Remark: Toxic for fish· Additional ecological information:· According to recipe contains the following heavy metals and compounds according to EC guideline NO. 76/464 EC: None· General notes:Avoid transfer into the environment.The product contains materials that are harmful to the environment.Also poisonous for fish and plankton in water bodies.Toxic for aquatic organismsWater hazard class 2 (German Regulation) (Self-assessment): hazardous for water.
· Results of PBT and vPvB assessment· PBT: Not applicable.· vPvB: Not applicable.
* 13 Disposal considerations
· Waste treatment methods· RecommendationMust not be disposed of together with household garbage. Do not allow product to reach sewage system.Hand over to disposers of hazardous waste.Full or only partially emptied cartridges must be disposed of as special waste in accordance with official regulations.
(Contd. on page 6) HK
Page 31 May 2016
Page 6/7
Safety data sheetaccording to 1907/2006/EC, Article 31
Printing date 09.06.2011 Revision: 09.06.2011Version number 6
Trade name: Hilti HIT-RE 500-SD
(Contd. of page 5)
DR
· European waste catalogue
08 00 00 WASTES FROM THE MANUFACTURE, FORMULATION, SUPPLY AND USE (MFSU) OF COATINGS (PAINTS,VARNISHES AND VITREOUS ENAMELS), ADHESIVES, SEALANTS AND PRINTING INKS
08 04 00 wastes from MFSU of adhesives and sealants (including waterproofing products)
08 04 09* waste adhesives and sealants containing organic solvents or other dangerous substances
20 00 00 MUNICIPAL WASTES (HOUSEHOLD WASTE AND SIMILAR COMMERCIAL, INDUSTRIAL AND INSTITUTIONALWASTES) INCLUDING SEPARATELY COLLECTED FRACTIONS
· Uncleaned packagings:· Recommendation:Disposal must be made according to official regulations.Dispose of packaging according to regulations on the disposal of packagings.Empty packs: May be disposed via the local Green Dot collecting system or EAK waste material code 150106 (mixed packaging materials)
* 14 Transport information
· Land transport ADR/RID (cross-border)· ADR/RID-GGVS/E Class: 8 Corrosive substances
9 Miscellaneous dangerous substances and articles.· UN-Number: 3259 / PG II
· HS-Code: 3214 10 10: Glaziers' putty, grafting putty, resin cements, caulking compounds and other mastics
15 Regulatory information
· Safety, health and environmental regulations/legislation specific for the substance or mixture
· Designation according to EC guidelines:The product has been classified and labelled in accordance with EC Directives / Ordinance on Hazardous Materials (GefStoffV)
(Contd. on page 7) HK
Page 32 May 2016
Page 7/7
Safety data sheetaccording to 1907/2006/EC, Article 31
Printing date 09.06.2011 Revision: 09.06.2011Version number 6
· Risk phrases:35 Causes severe burns.41 Risk of serious damage to eyes.20/22 Harmful by inhalation and if swallowed.43 May cause sensitisation by skin contact.51/53 Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
· Safety phrases:1/2 Keep locked up and out of the reach of children.23 Do not breathe fumes.51 Use only in well-ventilated areas.24/25 Avoid contact with skin and eyes.36/37/39 Wear suitable protective clothing, gloves and eye/face protection.26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.28 After contact with skin, wash immediately with plenty of water and soap.61 Avoid release to the environment. Refer to special instructions/safety data sheets.
· Special designation of certain preparations:Contains epoxy constituents. See information supplied by the manufacturer.
· National regulationsCouncil Directive 89/391/EEC of 12 June 1989 on the introduction of measures to encourage improvements in the safety and health ofworkers at work. Article 12 Training of workers
· Information about limitation of use: Employment restrictions concerning young persons must be observed.· Chemical safety assessment: A Chemical Safety Assessment has not been carried out.
16 Other informationThese data are based on our present knowledge. However, they shall not constitute a guarantee for any specific product features and shallnot establish a legally valid contractual relationship.
· Relevant phrasesR20/22 Harmful by inhalation and if swallowed.R35 Causes severe burns.R36/38 Irritating to eyes and skin.R43 May cause sensitisation by skin contact.R51/53 Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.R52/53 Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
· Department issuing data specification sheet:Hilti Entwicklungsgesellschaft mbHHiltistrasse 6D-86916 KauferingTel.: +49 8191 906310Fax: +49 8191 906826e-mail: [email protected]
· Contact: Monika Mönch· * Data compared to the previous version altered.
HK
Page 33 May 2016
Page 34 May 2016
Page 35 May 2016
Job / Application ReferenceProduct Name: HILTI RE 500 SD
Date Project Name Contractor ApplicationProject Type:ASD
2013 Kai Tak Development Rebar fixing
2015Kai Tak Trade & Industry Tower 工業及貿易發展局大樓 Dragages Rebar fixing
Project Type:Buildings
2014InterContinental, Holiday Inn and Cosmopolitan (Parcel 3) VOL Rebar fixing
2014Lok Wo Sha Complex Development 落禾沙綜合發展 HIP HING / EMAN Rebar fixing
2014 New World - Pak Kong Residential NEW WORLD Rebar fixing
2015Lok Wo Sha Complex Development 落禾沙綜合發展 HIP HING / EMAN Steel beam/bracket fixing
Project Type:HKAA
2015Airport Development 機場主要發展 GAMMON Rebar fixing
Project Type:Macau - Casino & Hotel2012 Macau Studio City MERCURIO SERVICOS DE ENGENHARIA Fixing on steel structural 2012 Macau Studio City MERCURIO SERVICOS DE ENGENHARIA Rebar fixing2012 Macau Studio City PAUL Y CONST CO LTD Rebar fixing2013 Galaxy Maga Resort銀河渡假村 Hsin Chong Catch fence fixing2013 Macau Studio City MERCURIO SERVICOS DE ENGENHARIA Rebar fixing2013 Macau Studio City Paul Y Yau Lee JV Rebar fixing2013 Macau Studio City VOL Rebar fixing2013 The Venetian Casino Resort MERCURIO SERVICOS DE ENGENHARIA Rebar fixing
2014City of Dreams Hotel Tower D新濠天地酒店大樓D Dragages Rebar fixing
2014 Galaxy Maga Resort銀河渡假村 Hsin Chong Rebar fixing
2014Galaxy Mega Resort (Phase 2)銀河渡假村二期 Hsin Chong Interior finishings fixing
2014Macao Studio City星麗門 Paul Y & Yau Lee JV Machine/Equipment fixng
2014Macao Studio City星麗門 Paul Y & Yau Lee JV Others
2014Macao Studio City星麗門 Paul Y & Yau Lee JV Rebar fixing
2014 Macau Studio City Paul Y Yau Lee JV Rebar fixing
2014MGM Cotai美高梅(路氹發展) China State Rebar fixing
701-704 Tower A, Manulife Fiancial Centre, 223 Wai Yip Street, Kwun Tong, Kwoloon , Hong KongHotline: 8228 8118 1
Page 36 May 2016
Job / Application ReferenceProduct Name: HILTI RE 500 SD
Date Project Name Contractor Application
2014MGM Cotai美高梅(路氹發展) CHINA STATE (HONG KONG) - CHINA Shear connector fixing
2014Wynn Palace永利皇宮 Leighton Others
2014Wynn Palace永利皇宮 Leighton Rebar fixing
2015City of Dreams Hotel Tower D新濠天地酒店大樓D Dragages Others
2015Macao Studio City星麗門 Paul Y & Yau Lee JV Aluminium cladding fixing
2015Macao Studio City星麗門 Paul Y & Yau Lee JV Machine/Equipment fixng
2015Macao Studio City星麗門 Paul Y & Yau Lee JV Others
2015Macao Studio City星麗門 Paul Y & Yau Lee JV Rebar fixing