This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
One look at the LvL One Wheel's finish tells you this all-purpose commercial wheel is different: • Industry's lightest commercial wheel by two pounds • Increases payload • Improves fuel efficiency • Six times brighter than the competitive wheel • Stronger and lasts longer than steel • Less maintenance • LvL ONE finish on both sides for any wheel position
ALCOA DURA-BRIGHT WHEELS WITH XBR TECHNOLOGY
Alcoa's patented Dura-Bright surface treatment allows easy cleaning - just use soap and water for a long-lasting, beautiful shine! And Dura-Bright wheels are no 53% more reflective than the first generation that truckers have loved mile-after-mile. Since Alcoa's Dura-Bright pen-etrates the aluminum, it won't crack, chip, peel or corrode - and it never needs polishing to maintain that sparkling appearance.
ALCOA DURA-FLANGE WHEELS
Specially treated to reduce or eliminate rim flange wear. Alcoa Dura-Flange wear protection wheels have half the rim flange wear of traditional aluminum wheels - or less. This design feature makes Dura-Flange wear protection wheels most appropriate for applications where loads are heavy and prone to shifting, causing tire walls to rub against the wheel rims. Alcoa Dura-Flange wear protection wheels are the only aluminum wheels on the market today that are protected from this type of wear, giving them at least double the life of other aluminum wheels in applications like transit bus, tanker and heavy hauling.
ALCOA FINISH OPTIONS
If the last digit in the part number is this, the finish is
0 - Brushed finish both sides as applicable 9 - Brushed finish in the inset position of a widebase wheel1 - Polished outside only DB - Dura-Bright2 - Polished inside only (same side as roll stamp) DF - Dura-Flange Wear Protection3 - Polished both sides DD - Dura-Bright and Dura-Flange 7 - LvL One finish on both sides as applicable* Wear Protection8 - LvL One finish in the inset position of a widebase wheel
*0 and 7 finish options on wide base wheel are finished in the outset position only.
Page 2
March 2013
Page 3
March 2013
ALCOA HUB-PILOTED EIGHT HOLE WHEEL275 mm (10.827") Bolt Circle221.1 mm (8.709") Center Bore(Special Order)
Notes:Before mounting the tire, perform a wheel fitment check to ensure proper clearance from obstructions. See Alcoa wheel service manuals and catalogs, your vehicle dealer or Alcoa representative for information on proper vehicle fitment procedures or before servicing thes wheels for proper load inflation and part compatibility information. Check with your dealer or Alcoa resources for proper load inflation and part compatibility information before servicing these wheels. Refer to the Alcoa Wheel Fitment Guide for detailed vehicle application, hardware and Alcoa accessory information. Please note: changing from original equipment tire size to aftermarket tire size can affect speedometer. Specifications are subject to change without notice. Do not exceed maximum wheel load. Compare OEM vehicle load rating to maximum wheel load rating. Do no overinflate. Refer to tire manufacturer's recommendation for proper tire pressure. Do not use abrassive polishes or cleaners on Clearcoat or Chrome wheels. Do not use Alcoa Aluminum Care System products on Clearcoat or Chrome wheels. Dually wheels have finish options - xxxxx(1) Polished Outside, xxxxx(2) Polished Inside, (R) is Rear, (F) is front. Some wheels also have an xxxxx(0) Machine Finish Offset (positive or negative) - The horizontal distance from the rim centerline to the mounting face of the wheel. Positive places the rim centerline inboard of the wheel mounting face. Negative places the rim centerline outboard of the wheel mounting face. Backspace - The horizontal distance from the wheel mounting surface to the inboard rim flange. Capacity ratings as single in highway service - bias-ply or radial. *1102 = 2 front axle end covers, 1103 = 2 rear axle end covers, Kit 110203 = two front axle end covers and two rear axle end covers **001004 = 2 front axle end covers, 001005 - rear axle end covers, Kit 100450 - two front axle end covers and two rear axle end covers
Page 12
March 2013
ALCOA FORGED WHEEL SPECIFICATIONS
Part Number Size Style Finish Bolt Circle Bolt Hole Bolt Hole Nut Seat Hub Backspace Offset-SRW Max. Wheel Max. Cold J2530 Max. Wheel Pilot Type Inches Dia Inches Bore Inches or Half Dual Load Inflaction Tire Weight Dia Space DRW Pounds PSI Dia mm Pounds Inches Inches 167041 16x7J Classic 8 Polish 8x6.5 0.62 60 degree conical 5.16 4.29 0.25 3750 110 NA 21 Stud160241(2) 16x6K Classic 8 Polish 8x6.5 0.67 Flat for 2pc lugnut 4.88 8.13 5.15 2780 95 NA 20 Hub160281(2) 16x6K Classic 8 Polish 8x6.5 0.67 Flat for 2pc lugnut 4.88 8.39 5.40 2780 95 NA 20 Hub176431 17x6.5 Classic 8 Polish 8x6.5 0.60 Flat for 2pc lugnut 4.60 8.81 5.59 3200 80 820 25 Hub176432 17x6.5 Classic 8 Polish 8x6.5 0.60 Flat for 2pc lugnut 4.60 8.81 5.59 3200 80 820 25 Hub176441 17x6.5 Classic 8 Polish 8x7.87 0.60 Flat for 2pc lugnut 5.60 8.81 5.59 3200 80 820 25 Hub176442 17x6.5 Classic 8 Polish 8x7.87 0.60 Flat for 2pc lugnut 5.60 8.81 5.59 3200 80 820 25 Hub176421 17x6.5 Classic 8 Polish 8x6.5 0.60 Flat for 2pc lugnut 4.77 8.81 5.59 3200 80 820 25 Hub176422 17x6.5 Classic 8 Polish 8x6.5 0.60 Flat for 2pc lugnut 4.77 8.81 5.59 3200 80 820 25 Hub661401 17.5x6.75 Classic 8 Polish 8x6.5 0.68 Flat for 2pc lugnut 4.77 4.06 0.00 6050 130 NA 30 Hub665401 17.5x6.75 Classic 8 Polish 8x6.5 0.62 60 degree conical 5.16 4.06 0.00 3500 130 NA 31 Stud763200(1,2) 19.5x6 Classic 8 Polish 10x8.85 0.60 Flat for 2pc lugnut 6.70 8.34 5.35 3750 110 NA 33 Hub763800(1,2) 19.5x6 Classic 8 Polish 8x8.85 0.60 Flat for 2pc lugnut 6.71 8.34 5.35 3750 110 NA 32 Hub
Page 13
March 2013
Description Part No. Thread Hex
Two-Piece 39874 M22 x 1.5 33 mm Washered Nut or E9020
HUB PILOT LUG NUTS
Description Part No. Thread Hex High
Hardened Outer & Front E5977-R & L 1-1/8"-16 1-1/2" 7/8" Cap Nut
Outer & Front *E5996-R & L 1-1/8" - 16 1-1/2" 1" Cap Nut
* For 22.5" x 9" Wheels. Also, for other wheels needing extra long grip nut.
STUD PILOT LUG NUTS
STUD PILOT LUG NUTS
Description Part No. Thread Thread O.A. O.D. I.D. Length
Hardened E5988-R & L 1-1/8"-16 3/4"-16 3-1/16" Inner Cap Nut Hardened Inner Cap Nut E7896-R & L 1-1/8"-16 3/4"-16 2-9/16" or Steel Inner Wheel & E7897-R & L 1-1/8"-16 3/4"-16 3-1/16" Aluminum Outer Wheel
Type Description Part No.
Hub Pilot 1-1/2" Hex Flange Nut 000182
Hub Pilot 33 mm Hex Flange Nut 000181
Stud Pilot 1-1/2" Hex 000150
HUG-A-LUG NUT COVERS
Page 14
March 2013
ALUMINUM WHEEL CAPS FOR ALCOA DUAL WHEELS
PART NUMBER DESCRIPTION PART NUMBER DESCRIPTION
002167 Height: 5.875". Long Cap. 5.15" Hub Diameter. 8 on 6-1/2" Bolt Circle. Has Alcoa Medallion.
003167 Height: 4.7". 5.15" Hub Diameter. 8 on 6-1/2" Bolt Circle. Has Alcoa Medallion.
008167 Height: 4.65" 5.15" Hub Diameter 8 on 6-1/2" Bolt Circle. Open Cap.
001611 Height: 1.125". For Dodge/Ford dual wheel applications. 8 on 6-1/2" Bolt Circle. Has Alcoa Medallion.
001612 Height: 4.75". For Dodge/Ford dual wheel applications. 8 on 6-1/2" Bolt Circle. Has Alcoa Medallion.
001681 Height: 4.75". Open Cap for Dodge/Ford dual wheel applications. 8 on 6-1/2" Bolt Circle.
003611 Height: 1.125". For Chevrolet/GMC dual wheel applications. 8 on 6-1/2" Bolt Circle. Has Alcoa Medallion.
003612 Height: 4.750". For Chevrolet/GMC dual wheel applications. 8 on 6-1/2" Bolt Circle. Has Alcoa Medallion.
011911 Height: 1.5". Fits front 10 hole wheels. 10 on 7.25" Bolt Circle. Has Alcoa Medallion.
011912 Height: 5.375". Fits rear 10 hole wheels. 10 on 7.25" Bolt Circle. Has Alcoa Medallion.
Page 15
March 2013
ALCOA ONE-PIECE HUB COVER SYSTEM FOR HUB PILOT
10-Hole, 285.75mm22.5" and 24.5" Wheels
Description Part No. Finish
Front Axle Kit includes: Two front covers and one 086100S Chrome removal tool. Use a short handle rubber mallet for application.
Rear Axle Kit includes: Two rear covers and one 087100S Chromeremoval tool. Use a short handle rugbber mallet for application
It's a One-Piece Wonder
• Reduces installation time: 1 part vs. 11for fleets or owner operators.
ALCOA HUB PILOT COVER SYSTEM HUB PILOTED10-HOLE 22.5" & 24.5" WHEELS
REAR HUB CAP
Part No Description Other Information
077188 1) Rear Hub Cap 10) Hug-a-Lugs
FRONT HUB CAPS
Part No Description Other Information
076188 1) Hub Cap 10) Hug-a-lugs
Page 17
March 2013
WARNINGWheel and tire servicing can be dangerous.To protect life and limb, be sure you understand and follow all mounting, demounting, maintenance, inspection, operational pro-cedures and safety instructions and practices.
For complete information contact:
Henderson Wheel & Warehouse Supply1825 South 300 WestSalt Lake City, UT 84115
or
Henderson Wheel & Supply112 West 34th StreetBoise, ID 83714
Ask for the following catalog:
"Alcoa Aluminum Truck Wheel Service Manual and Operating Instructions" or log on to www.strongwheels.com
Never mount 16.5" diameter tires on 16" diameter wheels.
Never mount 16" diameter tires on 16.5" diameter wheels.
Henderson Wheel and Warehouse Supply 1825 South 300 West • Salt Lake City, UT 84115