Page 1
ATTENTION: With the key out of the ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections are secure before cycling the ignition to test this product.NOTE: Refer also to the instructions included with the aftermarket radio.
The World’s best kits.® MetraOnline.com ©COPYRIGHT2021METRAELECTRONICSCORPORATION REV.11/10/21INSTBC-HDR-K1
I N S TA L L AT I O N I N S T R U C T I O N SBC-HDR-K1
KIT FEATURES•ISODDINradioprovision*•SaddleTrampinterfacewithbuiltinhandlebarcontrols•Waterresistantenclosureforaddedprotection•Antennaadapterincluded*ThiskitcanonlybeusedwithanISODDINradiothathasan“L”shapedchassisdesign.
KIT COMPONENTS•A)Radiohousing•B)Radiobrackets•C)#8x3/8"Phillipsscrews(4)•D)#10-32x1/2"Phillipssteelmachinescrews(4)•E)HandlebarControlinterface(notshown)
TOOLS REQUIRED•Panelremovaltool•Phillipsscrewdriver•Torxscrewdrivers•Allenwrenches
TABLE OF CONTENTSFairingDisassembly HarleyDavidsonStreetGlide,ElectraGlide,
Ultra,andLimitedmodels2014-up.............2-3 HarleyDavidsonRoadGlide2015-up..............4KitAssembly..........................................................5SaddleTrampInterfaceInstallation.................6-9
WIRING & ANTENNA CONNECTIONS(Included)
WiringHarness:SaddleTrampinterfaceandharnessAntennaAdapterHandlebarcontrolinterface
A B C
Harley-Davidson Street Glide, Electra Glide, Ultra, and Limited Models 2014-Up†Road Glide2015-Up††Non-amplifiedmodelsonly
VisitMetraOnline.comformoredetailedinformationabouttheproductandup-to-datevehiclespecificapplications
D
Page 2
2 386.257.1187 | MetraOnline.com
FAIRING DISASSEMBLY
Harley Davidson Street Glide, Electra Glide, Ultra, and Limited models 2014-up
1. Remove(4)T-27Torxscrewsfromtheinnerfairing.(FigureA)
2. Withafirmgriponthewindshield,remove(3)T-27Torxscrews.removethewindshield,theouterfairingwillalsobeloosened.(FigureB)
3. Removetheouterfairing,unpluggingtheheadlight.(FigureC)
4. Remove(2)T-27Torxscrewstoremovethefairingvent,andthenremovethevent.(FigureD
Continued on next page
(Figure C)(Figure A)
(Figure D)(Figure B)
Page 3
3REV. 11/10/21 INSTBC-HDR-K1
FAIRING DISASSEMBLY (CONT)
5. Remove(11)screwssecuringtheradio“dummy”bracket:(FigureE)
a. (2)T-27Torxscrewssharedwith thegaugeclusterandathirdT-27 Torxscrewtoremovethegauge clusterinstep7.
b.(4)5/32"Allenscrewsfacingoutward. c. (4)T-25Torxscrewssecuredtothe
radio“dummy”. d.(1)T-25Torxscrewsharedwiththe
storagepocket.
6. Removetheradiobracket.(FigureE)Note: Thisbracketwillbereusedwiththekitassembly.
7. Removethegaugecluster.(FigureE)
8. Remove(4)3/16Allenscrewsfromthesidesofradio.(FigureF)
Note:Thesescrewswillbereusedwiththekitassembly.
9. Slidetheradioouttowardtherearofthebike,disconnectthewiring,andthenremovetheradio.(FigureF)
(Figure E)
(Figure F)
Page 4
4 386.257.1187 | MetraOnline.com
FAIRING DISASSEMBLY (CONT)
Harley Davidson Road Glide 2015-up
1. Removethelowertorxscrewsoneithersideholdingthewinddeflectorwings(onlythelowertwoneedtoberemoved).(FigureA)
2. Remove(1)3/16"Allenscrewfromeachoftheturnsignals.(FigureB)
3. Remove(4)Phillipsscrewsfromthewindshieldandsetthewindshieldaside.(FigureC)
4. Removethetopfairingtrimclippedtothetopoftheradio.(FigureD)
5. Unplugtheturnsignals.
6. Removethespeakergrillswithapanelremovaltoolandremove(1)Torxscrewfromeachside.(FigureE)CAUTION:Thefairingwillbelooseatthispoint.Haveahelperholdittokeepfromdamagingitwhenremovingthescrews.
7. Removethefairingandsetaside.
8. Remove(4)3/16"Allenscrewsfromthesidesofthefactoryradio.Note:ThesescrewswillbereusedintheBC-HDR-K1kitassembly.CAUTION:Besuretoholdtheradiowhenremovingthelastscrewsoitdoesnotdrop.
9. Unplugandremovetheradio.
10. Remove(2)Torxscrewssecuringthefairingbracketattachedtotheradio.Note: ThisbracketwillbereusedintheBC-HDR-K1kitassembly.Pleasenotetheorientationofthebracket.Thecurvedportionfacestherearofthebike.
(Figure C)
(Figure B) (Figure E)
(Figure A) (Figure D)
Page 5
5REV. 11/10/21 INSTBC-HDR-K1
KIT ASSEMBLY
1. Securetheradio bracketstotheradio housingwith(4)#8x3/8"Phillipsscrewsprovidedinthiskit.(FigureA)
2. Slidetheaftermarketradiointotheradiohousingassemblyandsecurewithscrewssuppliedwiththeradio.(FigureB)
3. Securetheradiohousingassemblytothebikeusing(4)3/16"Allenscrewspreviouslyremovedinstep8ofdisassembly.(FigureC)
4. a. For the Street Glide, Electra Glide, Ultra, and Limited models 2014-up:
Attachtheradiobracketremovedinstep6ofdisassemblytothetopoftheradiohousingassembly,andsecurewith(4)#10-32x1/2"Phillipssteelmachinescrewsprovidedinthiskit.
b. For the Road Glide 2015-up: Attachthefairingbracketremovedinstep10ofdisassemblytothetopoftheradiohousingassembly,andsecurewith(4)#10-32x1/2"Phillipssteelmachinescrewsprovidedinthiskit.Ensurethebracketisfarforward,andthecurvedportionisfacingtherearofthebike.
Continue to BC-HDR-K1 Interface Installation
(Figure A) (Figure B) (Figure C)
Page 6
386.257.1187 | MetraOnline.com6
SADDLE TRAMP INTERFACE INSTALLATION
INTERFACE FEATURES
• Providesaccessorypower(12-volt10-amp)• Retainsbalance• Retainshandlebarcontrols:
•H-DHandlebarcontrolscanbeadded •71500248C'14-'20w/oTractionControl •71500561'20-Upw/TractionControl• USBMicro-Bupdatable
TOOLS REQUIRED
•Cuttingtool•Crimpingtool•Tape•Connectors(example:butt-connectors,bellcaps,etc.)
INTERFACE COMPONENTS
•SaddleTrampInterface: •Circuitboard •Housing,cap,andcover •Harness •3.5mmadapter
TABLE OF CONTENTS
Installation................................................................................................................................................6Connections...............................................................................................................................................7Programming............................................................................................................................................8Troubleshooting........................................................................................................................................9
IMPORTANT NOTE Caution - If the fuse on the aftermarket radio exceeds 10 amps you MUST run a fused wire from your vehicle’s battery to avoid potential damage.
Page 7
REV. 11/10/21 INSTBC-HDR-K1 7
CONNECTIONS
Yellow - Battery power
Black - Ground
Red - Accessory power
Orange - Illumination
Blue - Power antenna
Blue/White - Amp turn on from radio
Gray - Front right speaker (+)
Gray/Black - Front right speaker (-)
White - Front left speaker (+)
White/Black - Front left speaker (-)
Green - Rear Left speaker (+)
Green/Black - Rear Left speaker (-)
Purple - Rear Right speaker (+)
Purple/Black - Rear Right speaker (-)
DO NOT USE
DIN Connector Used with Single DIN Kits
Front
Rear
Sub
AUX-IN
Rear View
SWC
Zip-tie Mounts
Inside Case
CAUTION: If the fuse on the aftermarket radio exceeds 10 amps, you MUST run a fused wire from your vehicle’s battery to avoid potential damage.
Fuse
3.5mm Adapter (for radios with a wire for SWC)
Boss (with SWC wire):Key1(Gray)-BrownKenwood / JVC (with SWC wire):Blue/Yellow-BrownXITE:SWC-2-BrownUniversal Radio*:Key-AorSWC-1-BrownKey-BorSWC-2-Brown/White*Afterprogramming,assignSWCbuttonswithinradiomenu
Vehicles without handlebar controls
1. Fromthe3.5mmadapter,tietheBrown and Brown/White wirestogetherandtapeuporuseaconnector.
2. Connectthe3.5mmadaptertothe3.5mmjackfromthevehicleharness.
3. Programtheinterfacepertheinstructions,page8.
Page 8
8 386.257.1187 | MetraOnline.com
PROGRAMMING
1.Turntheignitionon.
2.Connectthe BC-HDR-K1 harnesstothewiringharnessinthebike.
3. For vehicles without hand controls: Theinterfacewillautomaticallyprogram.
4. For vehicles with hand controls: LocatetheVolume Upbuttonontheclutchsidehandcontrol.ProgramtheinterfacebytappingtheVolume UpbuttonataheartbeatpaceuntiltheLEDlightstopsflashing.
5. TheLEDlightwillflashGreen&Redwhiletheinterfaceprogramstheradiotothehandlebarcontrols.Onceprogrammed,theLEDlightwillgoout,thenproduceapatternwhichwillidentifytheradiotypeinstalled.
6.TheLEDlightwillgoout,thenonceagainquicklyflashGreen & Redwhiletheinterfaceprogramsitselftothevehicle.Onceprogrammed,theLEDlightwillgooutagain,thenturnsolidGreen.
7. Turntheignitionoff,thenbackon.
8.Testallfunctionsoftheinstallationforproperoperation.
Green & Red LED
Green or Red LED
Green & Red LED
Green LED
OFF
ACC ON START
OFF
ACC ON START
OFF
ACC ON START
VOL+
Do Not Touch
VOL+
Tap Volume Up
Page 9
REV. 11/10/21 INSTBC-HDR-K1 9
Note:IftheLEDlightshowsSolid GreenforPass(indicatingeverythingprogrammedcorrectly),yetthesteeringwheelcontrolsdon’twork,checktoensurethatthe3.5mmjackispluggedin,andalsopluggedintothecorrectjackontheradio.Oncecorrected,presstheresetbutton,thenprogramagain.
Final LED FeedbackAttheendofprogrammingtheLEDlightwillturnSolidGreenwhichindicatesprogrammingwassuccessful.IftheLEDlightdidn’tturnSolidGreen,referencethelistbelowtounderstandwhichprogrammingsectiontheproblemmaystemfrom.
TROUBLESHOOTING
1. 2.Iftheinterfacefailstofunctionyouwillneedtopresstheresetbutton.Toaccessthebuttonremovethecoverofthewaterresistantcase,slideoutthecircuitboardandpresstheresetbutton.TheLEDwillstartflashing,startingatstep2,repeattheprogramingprocess.
SolidGreenSlowRedFlash
SlowGreenFlashSolidRed
PassFailPassFail
PassPassFailFail
LED LightRadio
Programming Section
Vehicle Programming
Section
LED Light
Reset Button
Page 10
10 386.257.1187 | MetraOnline.com
Page 11
11REV. 11/10/21 INSTBC-HDR-K1
Page 12
The World’s best kits.® MetraOnline.com ©COPYRIGHT2021METRAELECTRONICSCORPORATION REV.11/10/21INSTBC-HDR-K1
I N S TA L L AT I O N I N S T R U C T I O N SBC-HDR-K1
KNOWLEDGE IS POWEREnhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.Log onto www.installerinstitute.edu or call 386-672-5771 for more information and take steps toward a better tomorrow.
®
Metra recommends MECP certified technicians
Havingdifficulties?We’reheretohelp.
ContactourTechSupportlineat: 386-257-1187 Orviaemailat: [email protected]
Tech Support Hours (Eastern Standard Time)Monday-Friday:9:00AM-7:00PMSaturday:10:00AM-7:00PMSunday:10:00AM-4:00PM