HAND FINISHING HAND FINISHING PROJECT #1 PROJECT #1 - End ‘A’ Parallel to ‘E’ End ‘A’ Parallel to ‘E’ .05mm .05mm - Side ‘B’ Parallel to ‘D’ Side ‘B’ Parallel to ‘D’ .05mm .05mm - Side ‘C’ Parallel to opposite Side ‘C’ Parallel to opposite side 38 mm .05 mm side 38 mm .05 mm - End ‘A’ Perpendicular to ‘B’ End ‘A’ Perpendicular to ‘B’ .05mm .05mm - End ‘E’ Perpendicular to ‘B’ End ‘E’ Perpendicular to ‘B’ .05mm .05mm - End ‘A’ Perpendicular to 45 End ‘A’ Perpendicular to 45 degree bevel .05mm degree bevel .05mm - End ‘A’ Perpendicular to 6 mm End ‘A’ Perpendicular to 6 mm radius .05mm radius .05mm SIDE B END A SIDE C 85 mm 27mm SIDE D 6 MM RADIUS 45 DEG/10 mm END E Finish all surfaces flat to within .05mm/.0019 in. and to an 80% Die Check Coverage. END E SIDE F (BASE MATERIAL: 1 ¼” X 1 ¾” X 3 ½” CRS)
8
Embed
HAND FINISHING PROJECT #1 - End ‘A’ Parallel to ‘E’.05mm - Side ‘B’ Parallel to ‘D’.05mm - Side ‘C’ Parallel to opposite side 38 mm.05 mm - End ‘A’ Perpendicular.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
HAND FINISHINGHAND FINISHINGPROJECT #1PROJECT #1
-End ‘A’ Parallel to ‘E’ End ‘A’ Parallel to ‘E’ .05mm .05mm-Side ‘B’ Parallel to ‘D’ Side ‘B’ Parallel to ‘D’ .05mm .05mm-Side ‘C’ Parallel to opposite side 38 Side ‘C’ Parallel to opposite side 38 mm .05 mmmm .05 mm-End ‘A’ Perpendicular to ‘B’ End ‘A’ Perpendicular to ‘B’ .05mm .05mm-End ‘E’ Perpendicular to ‘B’ End ‘E’ Perpendicular to ‘B’ .05mm .05mm-End ‘A’ Perpendicular to 45 degree End ‘A’ Perpendicular to 45 degree bevel .05mmbevel .05mm-End ‘A’ Perpendicular to 6 mm radius End ‘A’ Perpendicular to 6 mm radius .05mm .05mm
SIDE B
END A SIDE C
85 mm
27mm
SIDE D
6 MM RADIUS
45 DEG/10 mm
END E
Finish all surfaces flat to within .05mm/.0019 in. and to an 80% Die Check Coverage.
END E
SIDE F
(BASE MATERIAL: 1 ¼” X 1 ¾” X 3 ½” CRS)
WELD PROJECT #4WELD PROJECT #4
1) Using this as a template, center punch plate at every intersection.
2) Weld dots at each center punch approximately 1/8” dia. and 3/16” in height and create a ‘haystack’ point on each weld.
1) Weld edges of holes to createa edge repair bead that extends into the hole and on upper surfacethe same amount.2) Do not turn the plate.
WELD PROJECT #7WELD PROJECT #7
1 3/8”
1.07”
1.07”
1.25”
.46”
(Base material: ½” X 6” X 6” CRS)
1) Weld edges of holes to createa edge repair bead that extends into the hole and on upper surfacethe same amount.2) Do not turn the plate.
WELD PROJECT #8WELD PROJECT #8
.375” TYP1.15”TYP
.25”TYP
.25”
.50”TYP
.50” TYP
.50” TYP
Base material: 2” x 2” x 6” CRSSlots are .125 deep.Four sides typical.
1) Fill slots leaving novoids in bottom and build up surface to 3/16”above surface.2) Do not melt down thewalls between the slots.
WELD AND HAND FINISHWELD AND HAND FINISHPROJECT #9PROJECT #9
20 mm
20 mm
6.5 mm
LAYOUT AND BUILD UP BY WELDING TO PROVIDE ENOUGH MATERIAL TO HAND FINISH TO THE DIMENSIONS SHOWN AND COMPLETE CLEANUP.
ALL DIMENSIONS MUST BE WITHIN PLUS OR MINUS .04 mm / .0015 in.(BASE MATERIAL: 1 ¼” X 1 ¾” X 3
½” CRS)
WELD AND HAND FINISHWELD AND HAND FINISHPROJECT #10PROJECT #10
.751 - .747 DIA
THIS TASK IS TO MOVE THE .750 CENTER DIAMETER .250 IN THE DIRECTION OF THE ARROWS BY WELDING ONE SIDE OF THE CENTER DIAMETER TO ADD THE MATERIAL NEEDED TO HAND FINISH IT BACK TO THE ORIGINAL DIAMETER AND MOVE THE CENTER. GRINDERS AND FILES ARE USED FOR FINISHING..TOLERANCE IS .004 INCHES.
.250
(BASE MATERIAL: 2.0” DIA. X 2.0 LONG CRS)
DisclaimerDisclaimer This workforce solution was funded by a grant awarded This workforce solution was funded by a grant awarded
under the President’s Community-Based Job Training under the President’s Community-Based Job Training Grants as implemented by the U.S. Department of Grants as implemented by the U.S. Department of Labor’s Employment and Training Administration. The Labor’s Employment and Training Administration. The solution was created by the grantee and does not solution was created by the grantee and does not necessarily reflect the official position of the U.S. necessarily reflect the official position of the U.S. Department of Labor. The Department of Labor makes Department of Labor. The Department of Labor makes no guarantees, warranties, or assurances of any kind, no guarantees, warranties, or assurances of any kind, express or implied, with respect to such information, express or implied, with respect to such information, including any information on linked sites and including, including any information on linked sites and including, but not limited to, accuracy of the information or its but not limited to, accuracy of the information or its completeness, timeliness, usefulness, adequacy, completeness, timeliness, usefulness, adequacy, continued availability, or ownership. This solution is continued availability, or ownership. This solution is copyrighted by the institution that created it. Internal copyrighted by the institution that created it. Internal use by an organization and/or personal use by an use by an organization and/or personal use by an individual for non-commercial purposes is permissible. individual for non-commercial purposes is permissible. All other uses require the prior authorization of the All other uses require the prior authorization of the copyright owner. copyright owner.