Hand and Power Tools 12345BONUS 678910BONUS 1112131415BONUS 1617181920BONUS 2122232425BONUS.

Hand and Power Tools1 2 3 4 5 BONUS

6 7 8 9 10 BONUS

11 12 13 14 15 BONUS

16 17 18 19 20 BONUS

21 22 23 24 25 BONUS

When it is important that the object you are striking not be damaged which tool

is the best one to use?

A. Bell faced Hammer

B. Claw Hammer

C. Sledge Hammer

D. Mallet

A B C D

Which of the following wrenches is adjustable?

A. Striking Wrench

B. Box-end Wrench

C. Pipe Wrench

D. Combination Wrench

A B C D

A crosshead screw is tightened by using which of the following?

A. Allen Wrench

B. Torx Screwdriver

C. Phillips Head Screwdriver

D. Robertson Head Screwdriver

A B C D

You should discard a clamp with a ________.

A. Ridged Jaw

B. Sliding Jaw

C. Swivel Jaw that turns freely

D. Bent Frame

A B C D

Which of the following should you wear when you use a nail puller or a ripping

bar?

A. Safety Glasses, Hard Hat, Ear Plugs

B. Hard Hat, Safety Glasses, Gloves

C. Safety Glasses, gloves, Resporator

D. Hard Hat, Ear Plugs, Gloves

A B C D

A B C D

What type of hammer should never be used in the

construction industry?

A. Sledge Hammer

B. Ball Peen Hammer

C. Cast Head Hammer

D. Claw Hammer

Safe use of a wrench requires you to do which of the following?

A. Push it away from you.

B. Pull it towards you.

C. Use an extension.

D. Use the shortest handle available.

A B C D

Which one of these should be sharpened on an oil stone?

A. Punch

B. Chisel

C. File

D. Screwdriver

A B C D

Which tool would you use to drive a stake into the ground 18” to 24”?

A. Claw Hammer

B. Sledge Hammer

C. Wooden Mallet

D. Slag Hammer

A B C D

Which of the following would you use to cut heavy gauge wire?

A. Lineman's Pliers

B. Needle-nose Pliers

C. Channellock Pliers

D. Slip-joint Pliers

A B C D

Use this to maintain a saw blade properly.

A. Sand paper

B. Grinder

C. Emery cloth

D. A file

A B C D

A saber saw will cut more smoothly if you use this.

A. Oil

B. Water

C. Grease

D. Beeswax

A B C D

Proper maintenance of pliers requires you to do which of the

following?

A. Wipe with a soft cloth

B. Use Grease

C. Oil the joints

D. Wash with Water

A B C D

Which of the following is used to measure vertical distances?

A. Steel Rule

B. Micrometer

C. Measuring Tape

D. Wooden Folding Rule

A B C D

A _______ Square is used to mark many different angles.

A. Try

B. Carpenter’s

C. Rafter Angle

D. Framing

A B C D

Which of the following bits are used to drill in wood?

A. Auger

B. Carbide

C. Shank

D. Masonry

A B C D

When is a surface plumb?

A. Centered between two objects

B. Exactly horizontal

C. Exactly vertical

D. At a 45 degree angle

A B C D

When cutting with a circular saw you should always cut on this side of

the line.

A. Top

B. Bottom

C. Finish side

D. Waste or unused side

A B C D

This is essential to the safe operation of an electric drill.

A. Keyless chuck

B. Trigger lock

C. GFCI outlet

D. Chuck key holder

A B C D

You should stand at this point when using a circular saw.

A. Directly behind the work

B. To one side of the work

C. Directly in front of the cut

D. Directly over the work.

A B C D

ALWAYS do this when working on any power tool.

A. Disconnect power

B. Set the trigger lock

C. Remove the blade

D. Apply grease

A B C D

To extend the life of a hand held band saw blade you should do

which of the following?

A. Operate at low speed

B. Operate at high speed

C. Vary the speed

D. Operate at medium speed

A B C D

Which of these grinders is used to smooth a damaged chisel

head?

A. End

B. Angle

C. Bench

D. Detail

A B C D

Air pressure is used to power this kind of tool.

A. Hydraulic

B. Pneumatic

C. Aerodynamic

D. Electromagnetic

A B C D

The first step for operating an electromagnetic drill is_____.

A. Put the power to the On positionB. Put the electromagnetic switch

to the On positionC. Set the depth gaugeD. Turn the switch OFF

A B C D

What do you do if a nail gun leaves the nail head above the

surface.

A. Lower the air pressure

B. Raise the air pressure

C. Lower the nail size

D. Raise the nail size

A B C D

BONUSWhen does a belt sander work

best?A. When it is stationary on the

surface to be sandedB. Started at low speedC. When used with high grit paperD. Running at full speed before

you touch the surface

A B C D

BONUSA cracked grinder wheel will do

which of the following?

A. Ring clearly

B. Make a dull thud

C. Splinter

D. Develop visible cracks.

A B C D

BONUSHow far away should you keep

any part of your body from a cutting tool?

A. 1’

B. 6’

C. 3”

D. 6”

A B C D

BONUSDust from an electric sander is

_______.

A. Harmless

B. Explosive

C. Will damage the sander

D. Completely removed from the collection system

A B C D

BONUSWhich of the following is used to

break brick or concrete?

A. pavement breaker

B. Hammer drill

C. Pneumatic drill

D. Hydraulic jack

A B C D

INCORRECT

CORRECT