-
GTC-35035t Telescopic Boom Crawler Crane
GENERAL DATACRANE CAPACITY 35t at 3.0mBOOM 3-section,
10.9 m – 27.2 mDIMENSIONOverall Length 13.2 mOverall Width
(tracks extended) 4.8 mOverall Width (tracks retracted) 3.0
mOverall Width (tracks removed) 2.8 mOverall Height (working)
2.5mMASSGross Vehicle Mass (Standard Equipment Package)
32,432 kg
Counterweight 5,681 kgPERFORMANCETravel Speed 1.9 km/hr
3.1 km/hrGradeability 66%
CRANE SPECIFICATIONMODEL CAPACITYGTC-350 35t at 3.0m
BOOM3-section full power telescoping boom. System consists of
one doubleacting hydraulic cylinder with load holding valves and
extension andretraction cables.• Retracted Length: 10.9 m• Extended
Length: 27.2 m • Extension Time: 82 s• Elevating Angles: -1.5° to
80.0° • Elevating Time: 56 s• Max Lifting Height: 26.4 m• Boom
Head: Five cast nylon and One steel 373 mm diameter main
sheaves on heavy-duty roller bearings.
AUXILIARY BOOM HEADQuick reeve, single 373 mm diameter
high-strength, castnylon sheave mounted on a heavy-duty roller
bearing. Allows singlepart reeving.
COUNTERWEIGHT 1 piece integrated counterweight design.•
FixedConfiguration=5,681kgWINCHESPlanetary geared one-speed winch
includes a hydraulic motor, multidiscinternal brake and
counterbalance valve. Drum rotation indicatoris included (complete
winch performance specs on Page 3)• Main Wincho Rope Diameter and
Length: 16 mm x 152 moSinglelinepull:59.2kN(firstlayer)o Single
line speed: 78.1 m/min (fourth layer)
• Auxiliary Wincho Rope Diameter and Length: 16 mm x 91.4
moSinglelinepull:59.2kN(firstlayer)o Single line speed: 78.1 m/min
(fourth layer)
TRAVEL Each side frame contains a pilot controlled, two-speed
track drive withhydraulic axial piston motor and parking brake.
Travel system providesskid steering and counter rotation.• Travel
speed - 1.9 km/hr / 3.1 km/hr• Gradeability (unladen): 66%• Unladen
Ground Pressure: 0.53 kg/cm2
SWINGGear motor driving a planetary gear reducer with a shaft
mountedpinion, external gear shear ball slew bearing bolted to
thesuperstructure and the carbody allows the superstructure to
rotate 360°• Swing Speed: 0 - 2.2 rpm• Swing Parking Brake: Spring
applied failsafe brake with hydraulic
release that is controlled from the operators cab• Swing Service
Brake: Hydraulically applied, controlled through foot
actuated pedal• House Lock Systemo 2-position house lock (boom
over front or rear). Actuated from the
operator’s cab.
LOAD MOMENT INDICATORTADANO AML-C Rated Capacity Limiter and
Anti-Two Block system• OPTI-WIDTH™ - OPTIMAL lifting performance at
any track WIDTH• Control function shutdown. Audible and visual
warnings• LCD screen provides a continuous display of working boom
length,
boom angle, working load radius, tip height, swing position,
partsof-
line(operatorset),machinetrackconfiguration,relativeloadmoment,maximum
permissible load and actual load.
• Anti-two block weight allows quick reeving of hook
block•Operatorconfigurableworkingrangelimitswithautomaticsoftstop.
SPECIFICATION SHEET NO. TMC-DI-734-22 06/18
-
2
GTC-35035t Telescopic Boom Crawler Crane SPECIFICATION SHEET NO.
TMC-DI-734-22 06/18
Specifications are subject to change without prior notice.
FRAMEThe frame is an all-steel, welded structure, precision
machined to accept attachment of the boom and swing
components.OPERATORS CABFully-enclosed, air conditioned all-steel
modular cab with lockable
slidingdoor,acousticallining,anti-slipfloorandtintedsafetyglass.•
Rear view, winch view and right side view video cameras• Three
remote control work lights.• Vent window in the rear of the cab.•
Grab bars and steps are located for easy access to the cab.•
Defroster, heater, circulating fan• 2-speed windshield wiper, top
glass wiper• Six-way adjustable fabric seat with headrest, seat
belt• Dome light• Dry-chemicalfireextinguisher• Four-way electronic
armrest mounted joysticks control swing, main
winch, auxiliary winch, boom hoist and boom extend. Foot
pedalscontrol the travel and swing service brake functions. Swing
brakepedal is hydraulic.
• Selectable modes for Fine Control and Travel. Travel function
can beoperated by foot pedals or joystick.
• Seat termination switch immediately disable all hydraulic
functions asthe operator rises from the seat. Functions can also be
disabled byswitch on console.
• Dash instrumentation: tachometer, hour meter, fuel gauge,
andDEF level gauge. Indicators are provided for crane level,
swingposition,loadmoment,drumrotation,airfilterrestriction,engineoiltemperature
and pressure, hydraulic oil temperature and level,
andhydraulicandairfilterrestriction,andlowvoltage.
ENGINE • Make/ Model: Cummins QSB4.5• Type: 4 Cylinder, Water
cooled, 4 Cycle• Aspiration: Turbocharged and Aftercooled•
Max.Output: 129 kW @ 2200 RPM• Max Torque: 705 Nm @ 1500 RPM•
Piston Disp: 4.5 L• Emission Cert: U.S. EPA Tier 4f, Euromot Stage
IVELECTRICAL SYSTEM24 VDCFUEL SYSTEM• Capacity: 284 liter•
Filtration:Inlinefuel/waterseparatorandenginemountedfuelfilterSIDE
FRAMESTwo welded steel side frames are paired with a track group.
The side frames extend and retract hydraulically and are controlled
from the cab.• Track Rollers: Three top and ten bottom sealed
rollers on each track
frameIdler:Oilfilled,selflubricatingwithnitrogentypetensioner•
Track Shoes: 750 mm, 3-bar semi grouser
HYDRAULIC SYSTEM• Hydraulic Pumps: One high pressure, variable
axial piston pump with
load sense and power limiting control for crane functions. One
gearpump for cooling function.
• DirectionalValves:Multiplepressureandflowcompensatedvalveswith
integrated relief valves controlled by electrical signals.
• Pump output: 418 l/min @ 2200 RPM engine speed. 345 bar
maximumpressure
•
Reservoir:450litercapacity,spin-onfiller/breather,sightgauge,cleanout,
and sump drain.
•
Filtration:Three5-micron,fullflow,tank-mountedreturnfilterswithelectricalcloggingindicator.3-micronpilotoilin-linepressurefilter
• Diagnostic Ports: Provided for system, load sense, and pilot
pressure
EXTENDABLE JIBo Main jib• Total Length: 7.2 m • Offset Angles:
5°, 25° & 45°• Max. Lifting Height: 33.4 m
o Fly jib• Total Length: 12.8m • Offset Angles: 5°, 25° &
45°• Max. Lifting Height: 38.9m
HOOK BLOCK• 35t block, four sheaves, lockable swivel hook and
safety latch
TELEMATICS• Machine data logging and monitoring system with
HELLO-NET via
Internet.OPTIONAL EQUIPMENT• Overhaul ball – 4t with swivel hook
& safety latch• 360 degree house lock. Actuated from the
operator’s cab.• Track Shoes: 460 mm, 3-bar semi grouser• Auger:
Hydraulic auger boom package includes auger motor, hoses,
fasteners, and stowage bracket assembly mounted to the 2nd
stagesection of boom for variable radius drilling.
• Tool Circuit: Provides 23 l/min and 45 l/min at 176 bar
through
a15.2mtwinhosereelwithquickdisconnectfittingstooperateopencenter
tools.
• High Flow Tool Circuit: Provides 170 l/min at 330 bar•
Controlled Free Fall Hoists: Winches are available in controlled
freefallconfigurations.
• Cold Weather Packages: Cold weather options are available
foroperation to -40°C (Consult factory for application support)
• Work Platform: Model WP750 – 0.9m x 1.8m, all steel, welded,
two person platform with maximum capacity of 340 kg in approved
markets.
• Radio control package in approved markets.• Anemometer: boom
mounted wireless anemometer with cab display.• Central lubrication
system.
-
3
GTC-35035t Telescopic Boom Crawler Crane SPECIFICATION SHEET NO.
TMC-DI-734-22 06/18
Specifications are subject to change without prior notice.
Maximum Line Pull(kN)
Pitch Diameter
(mm)Layer (m) Total (m)
59 337 30 3055 370 33 6351 404 35 9847 437 38 13644 471 40 17742
504 43 220
MAIN WINCH AND AUXILIARY WINCH PERFORMANCE
6 89
4 785 83
2 673 73
Wire Rope: 16mm diameter rotation resistant. Line pulls are not
based on wire rope strength.
Rope Layer
Line Speed(m/min)
1 62
Auxiliary Nose Sheave 44
MACHINE WEIGHTSStandard Crane with 3 section - 27.2m boom,
5,670kg counterweight, 1 winch with wire rope, bi-fold jib and
750mm 3-bar semi grouser track shoes
OPTIONAL EQUIPMENT
Extendable jib - 7.2m to 12.8m
KG
32,432
KG
630
Auxiliary Winch with 91.4m wire rope 521
113
680
35t hook block - four sheave 353
4t Overhaul Ball
Complete Auger Package
Auger Ready Package 200
-
4
GTC-35035t Telescopic Boom Crawler Crane SPECIFICATION SHEET NO.
TMC-DI-734-22 06/18
Specifications are subject to change without prior notice.
DIMENSIONS
-
5
GTC-35035t Telescopic Boom Crawler Crane SPECIFICATION SHEET NO.
TMC-DI-734-22 06/18
Specifications are subject to change without prior notice.
WORKING RANGE DIAGRAM
-
LOAD CHARTS LOADS IN kg x 1000
Load chart data is for reference, load charts supplied in the
crane cab shall be used for lift planning.
6
GTC-35035t Telescopic Boom Crawler Crane SPECIFICATION SHEET NO.
TMC-DI-734-22 06/18
Specifications are subject to change without prior notice.
10.9 15.0 19.1 23.1 27.22.5 35.0 22.1 22.1 2.53 35.0 22.1 22.1
34 25.0 21.9 19.5 14.7 45 18.7 16.8 15.2 13.6 10.7 56 14.1 13.5
12.4 11.5 10.1 67 11.1 11.0 10.4 9.7 9.1 78 9.1 9.0 8.8 8.4 7.9 89
7.6 7.5 7.4 7.3 6.9 910 6.4 6.3 6.3 6.1 1012 4.9 4.8 4.8 4.7 1214
3.8 3.8 3.7 1416 3.0 3.0 3.0 1618 2.5 2.4 1820 2.0 2.0 2022 1.6
2224 1.4 24
Parts ofLine 8 6 6 4 4
Parts ofLine
RADIUS(m)
Main Boom Length (m) Radius(m)
MAIN BOOM with TRACKS FULLY EXTENDED ‐ 360°Up to 1.5° SLOPE5.7t COUNTERWEIGHT
-
LOAD CHARTS LOADS IN kg x 1000
Load chart data is for reference, load charts supplied in the
crane cab shall be used for lift planning.
7
GTC-35035t Telescopic Boom Crawler Crane SPECIFICATION SHEET NO.
TMC-DI-734-22 06/18
Specifications are subject to change without prior notice.
10.9 15.0 19.1 23.1 27.22.5 29.1 20.0 16.3 2.53 28.9 20.0 16.3
34 20.9 17.6 15.3 11.2 45 16.1 14.0 12.4 11.1 9.2 56 12.5 11.6 10.4
9.4 8.6 67 10.1 9.5 8.9 8.1 7.5 78 8.4 7.9 7.5 7.1 6.6 89 7.3 6.8
6.4 6.2 5.8 910 5.8 5.6 5.4 5.2 1012 4.6 4.3 4.2 4.0 1214 3.5 3.3
3.2 1416 2.8 2.7 2.6 1618 2.2 2.1 1820 1.9 1.8 2022 1.5 2224 1.3
24
Parts ofLine 8 6 6 4 4
Parts ofLine
MAIN BOOM with TRACKS FULLY EXTENDED ‐ 360°Up to 4° SLOPE
5.7t COUNTERWEIGHTRADIUS(m)
Main Boom Length (m) Radius(m)
-
LOAD CHARTS LOADS IN kg x 1000
Load chart data is for reference, load charts supplied in the
crane cab shall be used for lift planning.
8
GTC-35035t Telescopic Boom Crawler Crane SPECIFICATION SHEET NO.
TMC-DI-734-22 06/18
Specifications are subject to change without prior notice.
10.9 15.0 19.1 23.1 27.22.5 35.0 22.1 22.1 2.53 35.0 22.1 22.1
34 25.0 21.9 19.5 14.7 45 18.7 16.8 15.2 13.6 10.7 56 14.1 13.5
12.4 11.5 10.1 67 11.1 11.0 10.4 9.7 9.1 78 9.1 9.0 8.8 8.4 7.9 89
7.6 7.5 7.4 7.3 6.9 910 6.4 6.3 6.3 6.1 1012 4.9 4.8 4.8 4.7 1214
3.8 3.8 3.7 1416 3.0 3.0 3.0 1618 2.5 2.4 1820 2.0 2.0 2022 1.6
2224 1.4 24
Parts ofLine 8 6 6 4 4
Parts ofLine
MAIN BOOM with TRACKS FULLY RETRACTED ‐ OVER FRONT/REARUp to 1.5° SLOPE5.7t COUNTERWEIGHT
RADIUS(m)
Main Boom Length (m) Radius(m)
-
LOAD CHARTS LOADS IN kg x 1000
Load chart data is for reference, load charts supplied in the
crane cab shall be used for lift planning.
9
GTC-35035t Telescopic Boom Crawler Crane SPECIFICATION SHEET NO.
TMC-DI-734-22 06/18
Specifications are subject to change without prior notice.
10.9 15.0 19.1 23.1 27.22.5 * * * 2.53 * * * 34 * * * * 45 * * *
* * 56 7.0 6.9 * * * 67 5.6 5.6 5.4 5.0 4.7 78 4.6 4.6 4.5 4.3 4.1
89 3.8 3.8 3.8 3.7 3.5 910 3.2 3.2 3.2 3.1 1012 2.4 2.3 2.3 2.3
1214 1.7 1.7 1.7 1416 1.3 1.3 1.3 1618 1.0 0.9 1820 0.7 0.7 2022
0.5 2224 * 24
Parts ofLine 8 6 6 4 4
Parts ofLine
MAIN BOOM with TRACKS FULLY RETRACTED ‐ OVER SIDEUp to 1.5° SLOPE5.7t COUNTERWEIGHT
RADIUS(m)
Main Boom Length (m) Radius(m)
-
LOAD CHARTS LOADS IN kg x 1000
Load chart data is for reference, load charts supplied in the
crane cab shall be used for lift planning.
10
GTC-35035t Telescopic Boom Crawler Crane SPECIFICATION SHEET NO.
TMC-DI-734-22 06/18
Specifications are subject to change without prior notice.
RADIUS RADIUS
5° 25° 45° 5° 25° 45° 5° 25° 45° 5° 25° 45° 5° 25° 45°2.5 4.0
2.53 4.0 4.0 34 4.0 4.0 4.0 45 4.0 3.1 4.0 4.0 4.0 56 4.0 2.9 4.0
3.0 4.0 3.0 4.0 4.0 67 3.8 2.6 2.0 4.0 2.8 2.0 4.0 2.8 4.0 2.7 4.0
78 3.4 2.5 1.9 3.9 2.6 2.0 4.0 2.6 2.0 4.0 2.6 3.8 2.5 89 3.1 2.3
1.8 3.5 2.5 1.9 3.7 2.5 1.9 3.7 2.5 1.8 3.5 2.4 910 2.9 2.2 1.8 3.3
2.3 1.8 3.5 2.4 1.8 3.5 2.4 1.8 3.3 2.3 1.7 1012 2.5 2.0 1.7 2.8
2.1 1.7 3.0 2.2 1.7 3.1 2.2 1.7 2.9 2.1 1.6 1214 2.2 1.8 2.5 2.0
1.6 2.7 2.0 1.6 2.7 2.0 1.6 2.7 1.9 1.5 1416 2.0 2.3 1.8 1.6 2.4
1.9 1.6 2.5 1.9 1.5 2.4 1.8 1.5 1618 2.1 1.8 2.2 1.8 1.6 2.3 1.8
1.5 2.3 1.7 1.4 1820 1.9 2.0 1.7 1.9 1.7 1.5 1.8 1.6 1.4 2022 1.6
1.7 1.5 1.6 1.5 1.5 1.6 1.4 2224 1.4 1.3 1.3 1.2 1.3 1.3 2426 1.0
1.1 0.9 1.0 2628 0.8 0.7 0.8 2830 0.5 0.6 3032 0.4 32
PARTS OF LINE 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
PARTS OF LINE
10.9(m) (m)27.223.119.115.0
7.2m JIB with TRACKS FULLY EXTENDED ‐ 360°5.7t COUNTERWEIGHT
MAIN BOOM LENGTH (m)
-
LOAD CHARTS LOADS IN kg x 1000
Load chart data is for reference, load charts supplied in the
crane cab shall be used for lift planning.
11
GTC-35035t Telescopic Boom Crawler Crane SPECIFICATION SHEET NO.
TMC-DI-734-22 06/18
Specifications are subject to change without prior notice.
RADIUS RADIUS
5° 25° 45° 5° 25° 45° 5° 25° 45° 5° 25° 45° 5° 25° 45°3 34 2.4
45 2.1 2.3 2.2 56 1.9 2.0 2.2 2.0 67 1.7 1.8 1.9 2.0 1.8 78 1.5 1.1
1.7 1.8 1.9 1.8 89 1.4 1.0 1.5 1.1 1.6 1.7 1.8 910 1.2 1.0 1.4 1.0
1.5 1.0 1.6 1.1 1.7 1012 1.1 0.9 0.7 1.2 0.9 0.8 1.3 0.9 1.4 1.0
1.5 1.0 1214 0.9 0.8 0.7 1.1 0.8 0.7 1.2 0.9 0.7 1.3 0.9 0.7 1.3
0.9 0.7 1416 0.8 0.7 0.7 0.9 0.8 0.7 1.0 0.8 0.7 1.1 0.8 0.7 1.2
0.9 0.7 1618 0.7 0.7 0.6 0.9 0.7 0.6 0.9 0.8 0.7 1.0 0.8 0.7 1.1
0.8 0.7 1820 0.7 0.6 0.8 0.7 0.6 0.9 0.7 0.6 0.9 0.7 0.6 1.0 0.8
0.6 2022 0.6 0.7 0.6 0.6 0.8 0.7 0.6 0.9 0.7 0.6 0.9 0.7 0.6 2224
0.7 0.6 0.7 0.6 0.6 0.8 0.7 0.6 0.9 0.7 0.6 2426 0.6 0.7 0.6 0.8
0.6 0.6 0.8 0.7 0.6 2628 0.7 0.6 0.7 0.6 0.6 0.8 0.6 0.6 2830 0.6
0.7 0.6 0.7 0.6 0.6 3032 0.6 0.6 0.6 0.6 3234 0.6 0.5 0.5 3436 0.4
0.4 3638 0.3 38
PARTS OF LINE 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
PARTS OF LINE
12.8m JIB with TRACKS FULLY EXTENDED ‐ 360°5.7t COUNTERWEIGHT
MAIN BOOM LENGTH (m)(m) 10.9 15.0 19.1 23.1 27.2
(m)
-
12
GTC-35035t Telescopic Boom Crawler Crane SPECIFICATION SHEET NO.
TMC-DI-734-22 06/18
Specifications are subject to change without prior notice.
WP750 WORK PLATFORM ON MAIN BOOM RANGE CHARTFOR MANTIS MODEL
GTC-350
as originally manufactured and equipped by Tadano Mantis
Corporation
Shaded Area is Allowable Operating RangeLimits of operation:
Maximum load capacity = 340 kgMaximum radius when mounted on
main boom = 15.2 m
Maximum occupancy = 2 persons
WARNING: Travelling the crane with person(s) in the Work
Platform is not allowed.
WARNING: Lifting a load during Work Platform operation is not
allowed.
Notes:
1. It is permissible to leave the jibs stowed on the boom while
operating with Work Platform mounted to the main boom.
2. The hook block(s) must be removed when using the Work
Platform
-
13
GTC-35035t Telescopic Boom Crawler Crane SPECIFICATION SHEET NO.
TMC-DI-734-22 06/18
Specifications are subject to change without prior notice.
WP750 WORK PLATFORM ON 7.2 M EXTENSION RANGE CHARTFOR MANTIS
MODEL GTC-350
as originally manufactured and equipped by Tadano Mantis
Corporation
Shaded Area is Allowable Operating RangeLimits of operation:
Maximum load capacity = 340 kgMaximum occupancy = 2 persons
WARNING: Travelling the crane with person(s) in the Work
Platform is not allowed.
WARNING: Lifting a load during Work Platform operation is not
allowed.
Notes:
1. It is permissible to leave the jib section stowed on the boom
while operating with Work Platform mounted to the 7.2 M jib.
2. The hook block(s) must be removed when using the Work
Platform
-
14
GTC-35035t Telescopic Boom Crawler Crane SPECIFICATION SHEET NO.
TMC-DI-734-22 06/18
Specifications are subject to change without prior notice.
PLEASE READ, UNDERSTAND, AND FOLLOW THE MANUALS FURNISHED WITH
THE CRANE AS WELL AS THE CAPACITY LIMITA-TIONS AND GENERAL
CONDITIONS LISTED BELOW PRIOR TO OPERATI ON OF THE CRANE. FAILURE
TO DO SO MAY RESULT IN AN ACCIDENT.
Performance of this TADANO crane as manufactured by Tadano
Mantis Corporation applies only to machines as originally equipped
by the manufacturer and in a properly maintained condition.
Capacities given are maximum covered by the manufacturer’s warranty
and are based on
afreelysuspendedloadwithNOallowanceforfactorsasout-of-leveloperation(beyondthelimitsspecifiedonthecharts),supportingsurfaceconditions,
hazardous surroundings, experience of personnel, etc. The operator
shall establish practical working loads based on prevailing
operating conditions, such as, but not limited to the above.
The crane meets the requirements of ASME B30.5. Structure and
Stability have been tested in accordance with SAE J1063 and SAE
J765, respectively.
Maximum admissible wind velocity for working with telescopic
boom and jibs is 32 km/hr. Consult TADANO for ratings at higher
wind speeds.
Side pull on boom is extremely dangerous and must be
avoided.
DONOTexceedmanufacturersmaximumspecifiedreeving.Boom angle/boom
length relationships given are an approximation of the resulted
load radius, which should be an accurate measurement. Boom height
dimensions are measured from ground to center of lower boom head
sheave.
It is permissible to attempt to telescope boom with a load
within the limits of rated capacities. However, boom angle system
hydraulic pressure, and/or boom lubrication may affect
operation.
Itispermissibletotravelwithloadswithintheratedcapacityofthecrane.Travelspeedsshouldbegreatlyreducedtoreflectterrainlimitationsand
minimize dynamic loads applied to the crane structure.
Lifting capacities are shown in kgs x 1000.
The weight of load handling devices such as hook blocks, slings,
etc., must be considered as part of the load and must be deducted
from the lifting capacities.
The lifting capacities for the telescopic boom apply to a crane
with no jibs or other optional equipment stowed or mounted on the
crane.
The working radius is the horizontal distance from the center of
rotation to the center of the freely suspended, non-oscillating
load.
The lifting capacities are subject to change without prior
notice.
The above remarks are for basic information only and the
operator’s manual must be consulted before operating this crane.
All data and perfor-mances refer to the standard crane. The
addition of optional and other non-standard equipment may affect
the performance of the crane.
Load moment indicating and anti-two block systems are operator
aids and must never be used in lieu of job site lift planning
calculations by the operator which must take into account ground
conditions, weather and all other environmental factors prevailing
at the time of the lift.
Speci-ficationsaresubjecttochangeatanytimewithoutpriornotice.Illustrationsandphotographsmayshowoptionalequipment.Supersedesallprevious
issues.
-
NOTES
15
GTC-35035 Ton Telescopic Boom Crawler Crane SPECIFICATION SHEET
NO. TMC-DI-734-19 06/18
Specifications are subject to change without prior notice.
-
TADA
NO M
ANTI
S COR
PORA
TION
1705
Colu
mbi
a Ave
nue •
Fran
klin
, TN
3706
4 US
A • T
oll-F
ree:
1-80
0-27
2-33
25 •
Fax:
615-
790-
6803
• m
antis
cran
es.co
m
SPECIFICATION SHEET NO. TMC-DI-734-22 06/18
TADANO Ltd.,International Division4-12, Kamezawa
2-chome,Sumida-Ku, Tokyo 130-0014, JapanTel: +81 3 3621 7750Fax:
+81 3 3621 7785E-mail: [email protected]