GS3055-I Installation Process. CONFIDENTIAL GS3055-I Overview The GS3055-I is : 1.A universal wireless alarm communicator that can be used in a backup.

GS3055-I InstallationProcess

CONFIDENTIAL

GS3055-I Overview

The GS3055-I is:

1. A universal wireless alarm communicator that can be used in a backup or primary role.

2. A device which connects the alarm control panel to the GSM network and reports alarm signals directly to a monitoring central station receiver (Sur-Gard System III/ System II).

3. A digital transmitter which provides full reporting from any control panel that communicates using Contact ID format.

CONFIDENTIAL

GS3055-I Service Provider

What is CONNECT 24?

• CONNECT 24 is the GS3055-I service provider

• CONNECT 24 provides the automated telephone activation system for the activation of GS3055-I units (GVRU, Voice Response Unit)

• CONNECT 24 provides web-user interface support for the programming of GS3055-I units

• CONNECT 24 provides account administration, billing and rate plans to GS3055-I customers

CONFIDENTIAL

GS3055-I Enrolment Steps

In order to properly enrol a GS3055-I unit you must follow these steps :

STEP 1 – Activate your SIM card with Connect 24*

STEP 2 – Initialize the GS3055-I with Connect 24

STEP 3 – Determine best signal strength location

STEP 4 - Connect the GS3055-I to the control panel

STEP 5 - Program the control panel to use Contact ID format

STEP 6 – Test the GS3055-I

Note: GS3055-I unit must be powered down for STEPS 1 and 2

CONFIDENTIAL

GS3055-I SIM Card Activation (GVRU)

SIM Card Activations must be activated with Connect 24 prior to use. Please call the VRU at least 24 hours prior to installation. To activate a SIM Card, you will need the following information:

1. Installer’s ID Number: It identifies each installer listed on the Dealer Enrolment Form

2. Installer’s PIN Number: It identifies each installer with a 4 digit PIN number

3. The SIM Card Number: (Subscriber Identity Module), 19-20 digits located on SIM Card

Note: Only authorized dealers can activate a SIM Card with CONNECT 24

CONFIDENTIAL

GS3055-I Initialization (GVRU)

To initialize a GS3055-I unit, you will need the following information:

1. Profile Number: It represents the Central Station Receiver IP address and Rate Plan

2. Installer’s ID Number: It identifies each installer listed on the Dealer Enrolment Form

3. Installer’s PIN Number: it identifies each installer with a 4 digit PIN number

4. The Central Station Account Number: Account number to be transmitted to the Central Station Receiver

5. The SIM Card Number: (Subscriber Identity Module), 19-20 digits located on SIM Card

6. The DNIS Number: (Dialled Number Information Service), Check your work order

• Test transmission selection: daily, weekly or monthly

• Determine if GS3055-I unit is the primary or backup communicator

• Determine the type of installation Residential or Commercial

Note: Only authorized dealers can initialize a GS3055-I with CONNECT 24

CONFIDENTIAL

GS3055-I Signal Strength Test

To test the signal strength of a GS3055-I, you need:

1. The antenna must be connected to the GS3055-I

2. The SIM Card must be inserted into the GS3055-I

3. The Battery must be connected to the GS3055-I

The Signal Strength levels on GS3055-I are:

1. Excellent Signal Strength = GREEN LEDS 3 and 4

2. Good Signal Strength = GREEN LED 4

3. Poor Signal Strength = GREEN LED 4 (Flashing)

4. No signal Strength = OFF

For a proper installation, the GS3055-I must have

a Good Signal Strength

CONFIDENTIAL

GS3055-I – Telephone Wiring (Back-up Mode)

To Premise Telephones

From RJ-31X Demarcation

To Power Supply

CONFIDENTIAL

GS3055-I Control Panel Programming

Panel programming consist of:

Program any phone number (at least 1 digit) Program the corresponding account number Program the panel’s format as Contact ID Program Reporting codes or activate automatic reporting

option Enable the phone line communicator

CONFIDENTIAL

GS3055-I Testing

To test a GS3055-I unit, follow the next steps:

1. Disconnect the telephone line from the TIP and RING terminals on the GS3055-I unit

2. Verify that LED 2 (YELLOW) is ON. This indicates that the unit is in GSM mode

3. Connect a voltmeter to R1 and T1 on the GS3055-I unit, the voltage reading should be around 34.5Vdc (dial tone)

4. Arm the control panel and violate a zone, so that the panel attempts to report the event

5. Connect a butset to RING and TIP on the control panel to verify that the control panel is communicating

CONFIDENTIAL

GS3055-I – Testing

To Premise Telephones

To Power Supply

CONFIDENTIAL

GS3055-I

Questions?