GR-YG55DAA[GB].pdf

Printed in Thailand, Mar., 2008

SERVICE MANUAL

REFRIGERATOR-FREEZER

GR-YG55DAA (GB)

FILE NO. B10-2007097

B10-2007097_(Cover) 3/26/08, 2:43 PM1

– 2 –

Information essential for safety is listed in this service guide and on the product itself. Read the followinginformation thoroughly and comply with the instructions listed for each item.

L Label description

LABEL MEANING OF THE LABEL

WARNING indicates a situation in which a mistake in the service job by the serviceman or a third party inthe area or a problem with the product could result in death or serious personal injury to the user.

CAUTION indicates a situation in which a mistake in the service job by the serviceman or third party in thearea, or a problem with the product could result in injury or material loss (*) to the user.

* : Material loss as used here indicates large-scale damage to assets, household items or pets.

WARNING• Before starting the job always tell the customer not to let children approach.

Children may suffer injury from tools or disassembled parts etc.[Do not let children in the area.]

• Do the following before starting cooling cycle jobs(1) Watch out for nearby open flames.

Always put out any open flames before using gas connections, etc.If work is attempted without putting out the flames, the refrigerant which is mixed with oil could catch fire.

(2) Do not use welding equipment in an unventilated room.Carbon monoxide poisoning could result from poor ventilation while welding.

• Always remove the plug from the outlet when power is not needed such as duringdisassembly.Performing tasks such as disassembly and maintenance with the power still applied can cause electrical shocks.

CAUTION

WARNING

SAFETY ITEMS

B10-2007097_(02-10) 3/26/08, 2:40 PM2

– 3 –

• When the power must be on such as for jobs like circuitinspections use rubber gloves to prevent direct contactwith the charging circuit.Touching the charging circuit with bare hands can cause electrical shock.

• When replacing parts during equipment repair or maintenance always be sure touse only parts that match that particular model.Using the wrong parts can cause malfunctions or breakdowns as well as cause damage at the customer’s location such asfires and electrical leakage, etc.

• When terminating wire leads that have been cut,first attach the crimp terminals and then face thesealed side upwards and seal it to keep out water.Cover wire connections with putty and cover with a plastic bag sealed withelectrical tape at inside locations where water may splash on or whereexposed to much moisture or effects of the cooling cycle.If the connections are not protected as described here, damage may occur atthe customer’s location such as fires and electrical leakage, etc.

• Always make an inspection after the job is finished.(1) Always make a check of insulation resistance with a megger (500 volts)

connected between the charging section (plug) and chassis (groundterminal). The insulation resistance should be at least 20 megaohms.If this check is not made, trouble from poor insulation may causeproblems at the customer’s location such as electrical leakage or shocks,etc.

(2) When installing the refrigerator make sure the electrical cord is notbeing crimped or squeezed by the rear of the refrigerator, etc. Usingthe refrigerator with the electrical cord continually squeezed candamage the cord causing electrical leakage. Fires may also occur afterlongterm deterioration.

(3) Check the ground connections and repair any unsatisfactory points.(4) Inspect the electrical (power) cord and the plug. Replace it if it has too

much slack or is frayed and worn, etc.If the metal prongs of the plug or the plug installation surface has duston it wipe it away thoroughly.Using with dust or other contamination still on these surfaces may causefires, etc.

Face me upwardsfor to keep out water!

crimp terminal

WARNING

plastic bag

crimp terminal

putty

electrical tape

At least 20 Megaohms is okay!

B10-2007097_(02-10) 3/26/08, 2:40 PM3

– 4 –

CONTENTS

SPECIFICATIONS .................................................................................................................................... 4

CONSTRUCTION VIEWS ........................................................................................................................ 5

CIRCUIT DIAGRAM ................................................................................................................................. 6

SPECIFICATIONS OF ELECTRICAL PARTS .......................................................................................... 7

STRUCTURAL DRAWING ....................................................................................................................... 9

REFRIGERATION PIPING SYSTEM ..................................................................................................... 10

PIPING COMPRESSOR CHAMBER ..................................................................................................... 11

AUTOMATIC ICE MAKER ...................................................................................................................... 12

WATER SUPPLY .................................................................................................................................... 14

WATER DISTRIBUTION ........................................................................................................................ 15

REFRIGERATOR CONTROL SYSTEM ................................................................................................. 17

HYBRID PLASMA DEODORIZATION SYSTEM .................................................................................... 18

DEFROST CIRCUIT CHECKING METHOD .......................................................................................... 19

HOW TO REPLACE MAIN PARTS ........................................................................................................ 21

EXPLODED VIEWS ............................................................................................................................... 25

PARTS LIST ........................................................................................................................................... 32

SPECIFICATIONS

Specifications are to change without notice.

Rated Voltage, Frequency 230-240V~/50Hz

CompressorType FL1462-SM

Output (W) 140

Refrigerant Charge Volume (HFC-134a) (g) 210

Overall Capacity (I) 532

Freezer Compartment (I) 188

Refrigerator Compartment (I) 344

Height (mm) 1625

Dimensions Width (mm) 763

Depth (mm) 776

Net Weight (kg) 93

GR-YG55DAAMODELITEM

B10-2007097_(02-10) 3/26/08, 2:40 PM4

– 5 –

CONSTRUCTION VIEWS

GR-YG55DAA

B10-2007097_(02-10) 3/26/08, 2:40 PM5

– 6 –

CIRCUIT DIAGRAM

GR-YG55DAA

WIRING COLOR

Gn-y : Green-Yellow

Bl : Blue-White or Blue

Bk : Black-White or Black

Br : Brown-White or Brown

Or : Orange-White or Orange

Yw : Yellow

Pi : Pink

Wh : White

L N

MWaterPumpMotor

RunningCapacitor

Bk

Or

Yw

RY2

RY5

Or

Br

RY4

Yw

RY1

RY3 Bk

Bl

Bl

Bk

P.C.B.(250V-15A)

Varistor

SensorA.I.M.

MA.I.M.Motor

Current Fuse

SwitchTest

Br

ControlA.I.M.

P.C.B.ControlTemp.

Water Supply Nozzle Heater

F Lamp

R Lamp

Br

Or

Br

Yw

Bl

Bl

Bl

Bl

BlBl

SwitchingCurrent FusePower Supply

High Voltage Transformer

Over LoadRelay

Bk Wh

Bk

Defrost Heater

BlBl Pi

BlWh

Thermal Fuse

Pi BlPi Bl

(250V-3A)

PTC Relay

WhBl M

Compressor

CA

Bl

Bl

Bl

Gn-y

UV Fresh Guard Unit

Switch

SwitchR Door

F Door

SensorD

SensorFanMotor

MDC

LED

F

Main Control P.C.B.

Gn-y

Wh

Br

EPlug

Bl

)(339

)(15.1K

(76 C)

Closed-End Connector

Fasten ReceptacleRelay Housing

Soldering

Base Housing

Relay Contact

CapacitorChoke Coil

B10-2007097_(02-10) 3/26/08, 2:40 PM6

– 7 –

SPECIFICATIONS OF ELECTRICAL PARTS

Type FL1462-SM

Rated Voltage and Frequency 220-240V, 50Hz

Compressor Starting Current 6.56A

Main Winding Resistance (75°C) 17.4Ω

Auxiliary Winding Resistance (75°C) 35.6Ω

Type PGT0SAT

Resistance 33Ω

PTC RelayMaximum Voltage 300V

Maximum Current 7A

Relay Reset Time Within 2 Min.

Operation Time 0.15~0.65 Sec.

OverloadType 1.8C36A1

Relay Non Operation Current 1.8A (60°C)

Initial Operation Current 6.6A

Type UDQM002G2T0

Fan Motor Rated Voltage and Frequency DC 12V, 50Hz

Input 2.34W ± 15%

No. of Turns 2550 ± 150 rpm

Type RF-370CN-12560

Water Pump Rating Voltage DC 10V

AutomaticMotor Current 11.7 (± 3) mA

Ice Maker Revolutions 2510 ± 100 rpm

A.I.M. MotorType RF-370CN-13510

IM 801T Rating Voltage DC 12V

Staring Current 680 mA or less

Type SF76N

Thermal Fuse Rating 250V - 10A

Fusing Temperature 76°C

Water SupplyElectrical input 2.43W/m

Nozzle Heater Rating 240V-3.8W

Resistance 15.10 KΩ

Max rated Power 220 mW

A.I.M. Sensor Dissipation Factor 4 mW/°C

Temperature Range – 40 ~ ± 80°C

Type IC-EW-460

Hall IC Voltage 14V

Operating ambient Temp (25°C) – 30 ~ 90°C

ITEMMODEL GR-YG55DAA

B10-2007097_(02-10) 3/26/08, 2:40 PM7

– 8 –

THERMISTER SENSOR

L Terminal placement on compressor

A

C

M

Defrost HeaterRated Voltage - Input 240V - 170W

Winding Resistance 339 ± 7%Ω

D SensorType Heater off when D sensor temp reached at 10°C

Temperature ON : 20°C OFF : 10°C

F SensorType THERMISTER SENSOR

Temperature ON : –18°C OFF : –24°C

Door SwitchType D3D - 121

Rating 250V - 0.5A

Type 1KE98139B

Running Capacitor Reted Voltage 400V

Reted Capacity 3µF

ITEMMODEL GR-YG55DAA

B10-2007097_(02-10) 3/26/08, 2:40 PM8

– 9 –

STRUCTURAL DRAWING

F Sensor

Fan Motor

Thermal Fuse

Evaporator

Hybrid Plasma Deodorizer

Glass Tube Heater

Damper Thermister Sensor

Lamp (Refrigerator)

Compressor

Power P.C.B.

Door Switch(Refrigerator)

Door Switch(Freezer)

Lamp (Freezer)

Tank WaterSupply

Automatic IceMaker

Control P.C.B.

D Sensor

Pump

UV LED

B10-2007097_(02-10) 3/26/08, 2:40 PM9

– 10 –

REFRIGERATION PIPING SYSTEM

• Refrigerant Passage

Evaporator

Accumulator

Capillary Tube

Dryer

Clean Pipe

Radiation Pipe

Rear PlatePipe

EvaporatingpipeCompressor

Suction Pipe

Radiation Pipe(Right)

Clean Pipe

Radiation Pipe (Left)

Rear plate Pipe

Evaporator

Accumulator

Suction Pipe

Capillary Tube

Dryer

Evaporating Pipe

Compressor

B10-2007097_(02-10) 3/26/08, 2:40 PM10

– 11 –

PIPING COMPRESSOR CHAMBER

Rea

r pl

ate

pipe

(in

let)

Rad

iatio

n pi

pe(L

eft)

(ou

tlet)

P.C

.B. b

oxRad

iatio

n pi

pe(R

ight

) (in

let)

Eva

pora

ting

pipe

Rea

r pl

ate

pipe

(ou

tlet)

Rad

iatio

n pi

pe (

Left)

(in

let)

Dry

er

Bal

ance

r

Suc

tion

pipe

Com

pres

sor

B10-2007097_(11-24) 3/26/08, 2:41 PM11

– 12 –

M

M

AUTOMATIC ICE MAKER

Ice Maker Structure (IM-801T)

Main Board

Test switch5

(Blue) IM1

(Purple) IM2(Brown & White)VCC(Orange) ITH(Black) FLAT(Yellow) GND(Red & White) PMPe

(Black & White) PMPd

(Yellow & Green)(Blue & White)

Ice tray sensor

Tray motor Hdc-lcUsed todetect theposition

Water supply motor

Water supply heater

Inspection procedure

Test switch Showing the door AIM water Contentsopened/closed supply unit

ON (2 Sec) ON

FLASH

DoorDoor opened

↓ON

Door closed↓

FLASH

OFF

Start making ice.

Inspect the icecubes.

Release the icecubes.

Rotate to theopposite side.

Check if theicemaker trayrotates into thehorizon position.

Water supply

Rotate to theoriginal position.

22 ~ 32seconds

4.2seconds

• Open the door.

• After the test switch has been pressed and hold for 2 seconds for theinspection, the light will be on.

• After the switch is released, the light will flash (and keep flashing tillthe final step).

• The icemaker tray starts rotating.CAUTION ➀ In case of the above mentions, the ice maker traycannot rotate.– The ice making operation: the icemaker tray starts rotating after

finishing to produce ice.– The ice maker tray operation: The tray will rotate again into the

horizontal position.– The first inspection: The inspection starts after the ice maker tray

rotates into the horizontal position.CAUTION ➁ If the test switch is pressed during the operation of icecube releasing has been prepared, the tray will rotate 2 rounds.

• Start to distribute the water.

PCBP6

P2

B10-2007097_(11-24) 3/26/08, 2:41 PM12

– 13 –

Flow Chart showing the primary inspection

Power Supply ON

During the ice makingoperation

NO

NO

YES

Does the ice maker keepoperating after the water is

drained about 90 - 100 minutes?

Is the temperature sensorlower than 12.5°C or lower

than 9.5°C for 2 hours?

Inspects the ice cubes with theorientation of 45° leftwards.

Is there enoughwater?

Ice makingNO

YES

The tray rotates 30°Cbackwards.

Is the lever position toolow or is the door left

opened?

The tray rotates into the horizontalposition.

NOYES Begin the ice sensorevery 90 minutes.

Every door iscompletely closed.

The machine distributes water.

Is the temperaturesensor higher than

9.5°C?

Operate every15 minutes after

water distribution.

Is the door leftopened after water

distribution?

Does the machinebegin the water

distribution?

YES

NO

NO

NO

NO

NO

NO

YES

YES

YES

YES

YES

Inspection Sensor (Thermister)SENSOR

The operation of ice makingwill be complete if the

temperature sensor is at–12.5°C or lower than –9.5°C

for 2 hours.

Inspection Sensor (Thermister)Hole - Ic

Inspectionlever

If the ice box is fullof the ice cubes, the

machine will stopreleasing.

Ice cube releasing (Rotating direction)

134°

(Rotate → Release → Rotaterightwards.) the ice cubes. backwards.

The position The positionis checked is checked

with Hole - Ic with Hole - Ic

The water leaks/flows with the doorclosed-opened.

If the F door (upper) is opened, the machine willstop releasing the ice cubes and dropping waterto the ice maker tray.

AUTOMATIC ICE MAKER (NEXT)

B10-2007097_(11-24) 3/26/08, 2:41 PM13

– 14 –

WATER SUPPLY

Item IM-801TTop

In case of ice cubes (Wait for ice releasing)

Horizontal At a slope of 30°

(A slope of 30° is a normal direction because of a different time.)

Top Bottom

The ice maker tray is horizontal. The ice maker tray is at a slope of 30°.

(Depending on the time of operation)

Every 90 minutes after the ice making, the ice cubes will be checked withthe tray rotated leftwards.

After the ice tray is completely checked with its leftward rotation, the traywill rotate rightwards 1 round (Rotate leftwards about 45° → rotaterightwards → ice twist → rotate into horizontal position). However, duringthe inspection before the ice cubes are released, the tray with full ice cubeswill continuously rotate 2 rounds, after that, the water will be distributedagain.

While the ice makeris operating

While the machine ischecked if the icecubes are full

Checking

The position of the levelsensor

Check if there are any icescubes in the ice tray

The position of the levelsensor

Check the ice cubes

Ice Tray

B10-2007097_(11-24) 3/26/08, 2:41 PM14

– 15 –

WATER DISTRIBUTIONThe water is supplied by the operation of the water supply pump with the movable extended magnet.

General Structure of Ice Making

Ice Panel

Automatic IceMaker

Ice Box

TankCover

Tank Holder

Water SupplyTank

Water SupplyPipe - A

Water SupplyPump

Shelf

Air Supply Pipe Cover

Hose

Tank Holder - B

Water Supply Case

Water Supply Motor

Tank Shelf

Water Supply Pipe cover

Foam Cover

B10-2007097_(11-24) 3/26/08, 2:41 PM15

– 16 –

Operation of Water supply

• In 9.4 Sec. the water is supplied 105 ± 25 CC.

Water Supply Tank

Water Supply PumpMagnet

Magnet

Water Supply Motor

How to troubleshoot the ice maker

1. Installation/Inspection➀ Check if the water supply is properly installed.➁ Check if the freezing temperature sensor is properly installed.

2. How to measure the resistance of freezing temperature sensor

Remove the ice maker cover and wiring harness at theconnection with the automatic ice maker

Is it normal?

NO

Replace withthe new wiring.

Replace the mainboard (circuit board).

Resistance of the freezingtemperature sensor0°C 13 ~ 14.5kΩ25°C 4.5 ~ 5.5kΩ

Measure the resistance of thepin No. 3-4 between the wire

colored black and orange of thetemperature sensor.

Resistance

AIM connector

B10-2007097_(11-24) 3/26/08, 2:41 PM16

– 17 –

1. Cooling control

(1) Adjustment ofrefrigerationroom tempera-ture

• By circulating cold air sent by a fan in the refrigerator, the refrigeration room will be cooled.Temperature adjustment is made by using gas pressure type damper, controlling the opening of baffleplate according to the refrigerator temperature to adjust the volume of cold air.

(2) Adjustment offreezing roomtemperature

• When integrated compressor operating time attains 11 hr (50Hz), defrost-during the defrostingoperation, compressor and fan motor should be stopped and glass tube heater located below thecooler will be energized and defrosting carried out.

• Compressor and fan motor are turned on and off by detecting the temperature of freezing room byF-Sensor.Freezer is refrigerated by circulating cooler-cooled air by fan motor.

2. Defrost control

Normal running Defrost *Dead time Normal running

Compressor

Fan motor

Glass tube Heater

* Dead time (50Hz): 7 min.

(Defrost Timing Chart)

12345678901234123456789012341234567890123412345678901234

12345678901234123456789012341234567890123412345678901234

1234567890123456123456789012345612345678901234561234567890123456

12345678901234567123456789012345671234567890123456712345678901234567

12345678901234567123456789012345671234567890123456712345678901234567

REFRIGERATOR CONTROL SYSTEM

Temperature adjusting dial

F-S

enso

r

Compressor and fan motor

Temperaturedifferenceabout 5°C

WARM NORMAL COLD

OFFON

(°C)

B10-2007097_(11-24) 3/26/08, 2:41 PM17

– 18 –

HYBRID PLASMA DEODORIZATION SYSTEM

Hybrid plasma deodorization

The hybrid plasma deodorizer device is setting at control panel in the refrigerator compartment. There are two major functionOne operate by Plasma deodorizer generates high-voltage corona discharge Within the odorous atmosphere, generating activemolecles, radicals and ozone to oxidizes odorous that sophisticated at honey comb catalyst and kill the bacteria.The other one is operate by photo-catalyst, Our photocatalgtic titanium oxide are capable to decomposing Ethylene gas. lt willturn ethylene gas into carbon dioxide and water by light irradiation.

UV Fresh guard

UV Fresh guard is an ultra viloet (UV) LED ray in the chiller compartment that kills bacteria on fish and meats. According to thetests done by Japan Food Annalysis Center.UV LED removes 95% of bacteria. Thus your fish and meats last longer and stay fresher.

B10-2007097_(11-24) 3/26/08, 2:41 PM18

– 19 –

DEFROST CIRCUIT CHECKING METHOD

1. Outline of the Operation

Operation status

1. Cooling

2. Defrosting

3. Defrost completion

Circuit status Operation

Microcontroller will count the time for the operation ofthe compressor. Defrosting water will start when theultimate time reaches 7 ~ 13 hours.

With the specific accumulated time, the relay willstart to operate causing the thermal tube to get theenergy.

When the temperature sensor reaches the specifiedtemperature, the relay will stop operating and themicrocontroller will count the time again.

The microcontroller will control the compressor tooperate after defrosting ice completes about 4 ~ 7minutes.

Failure Mode and Symptoms

Compressor Relay

Glass-tubethermal Relay

PCB

COM

COM

COM

PCB

PCB

Failure mode Symptoms Checking method

Check if thermal relay runs.

Check conductivity of thermal fuse.

Cool off the dual steel below –5°C, then check forthermal conductivity of the circuit.

Check conductivity of timer contacts.

Check conductivity of glass tube heater.

Next page

Too much frost attached(Not enter defrost operation)

Too much frost attached (Enter defrostoperation, but no current flows to theheater, causing the defrosting operationto run after 4 ~ 7 minutes later.)

Too much frost attached(Not enter defrost operation)

Not cooled(Stopped under defrost condition)

1. Thermal relay does not run.

2. Thermal fuse breakdown

3. Relay is broken.

4. Glass tube heater breakdown

5. Relay contact connected

B10-2007097_(11-24) 3/26/08, 2:41 PM19

– 20 –

2. Checking method

No cooling

Does relay supplycurrent to heater?

Does compressor rotatewhen relay stops supplying

current to heater?

Check conductivity ofglass tube heater.

Relay NG.

Check control switch,compressor.

Relay NG. (contact NG)

Failure of glass tube heater.Breakdown.

Yes

No

Yes

Conductivity OK.

No

No

Yes

Check lead wireconnection.

Check lead wireconnection.

Check lead wireconnection.

B10-2007097_(11-24) 3/26/08, 2:41 PM20

– 21 –

• Before starting the job always tell the customer not to let children approach.Children may suffer injury from tools or disassembled parts etc.[Do not let children in the area.]

• Always remove the plug from the outlet when power is not needed such as during disassembly.Performing tasks such as disassembly and maintenance with the power still applied can cause electricalshocks.

• When the power must be on such as for jobs like circuit inspections use rubber gloves to preventdirect contact with the charging circuit.Touching the charging circuit with bare hands can cause electrical shock.

• When replacing parts during equipment repair or maintenance always be sure to use only partsthat match that particular model.Using the wrong parts can cause malfunctions or breakdowns as well as cause damage at thecustomer’s location such as fires and electrical leakage, etc.

HOW TO REPLACE MAIN PARTS

WARNING

L Door Switch

(1) Pry off the cover with a tool such as a blade d screwdriver.(Take care not to scratch the surface of inner liner.)

L P.C.B. BOX

(1) Remove the grill on the rear and also the P.C.B boxsetscrews (2 pcs.) and power cord setscrew (1 pc.).

(2) Remove the P.C.B box clips (4 points).

FREEZER

L Shelf (freezer)

(1) To release the stand lock, push and hold the stand lock,then pull the shelf out.

Ice corner partition plate

Shelf (freezer)

Setscrew

PCB Cover

Fixer-A

(2) Remove the front cover of the automatic ice maker.

Stand lock

Insert your hand under thecover and push out both locksside by side.

How to push out the locksPower PCB

PCB Fixer

B10-2007097_(11-24) 3/26/08, 2:41 PM21

– 22 –

L Fit the fan motor on evaporator cover middle.

Install the fan motor to the evaporator cover middlefollowing the arrow direction.Then tighten with screws.

L Freezer Compartment

L Evaporator Cover (Middle)

L Evaporator Cover(1) Use screwdriver take off evaporator cover out (total of

3 points)

Fan motor

Temperaturefuse

F Sensor

Evaporator

Setscrew

Accumulator

Setscrew

Heater cover

Glass tube heater

\ Install the air seal securely on the lead wire routing.

\ Remove fan from motor cover.\ Take housing out.

L Fan motor

\ Should push fan unit it hit the motor shaft end.

Soft tapeFan motor

Screw

Evaporatorcover middle

B10-2007097_(11-24) 3/26/08, 2:41 PM22

– 23 –

L Evaporator (continued)

L Glass Tube Heater

Heater clamp

(2) Connect the glass tube heater wire leads as shown in thedrawing below and secure with a piece of tape.

(1) Take thermal fuse of evaporator cover middle rear fixer.(2) Always reinstall the parts in their original positions.

L Temperature Fuse

Evaporator covermiddle

Temperature fuse

(2) Pull the accumulator slightly towards you and then movethe entire evaporator by lifting it upwards. (Be careful not tocrush the pipe part of the accumulator marked with anarrow →.)

Accumulator

Evaporator

Raise upwards andremove

Glass tube heater

Front

Glass tube heater

Wire leads

(1) Cut the glass tube wire leads at both ends and release fromthe heater clamp with the upper and lower heater coversstill attached.

Tape

Sensor

L Temperature sensor

\ The temperature sensor is installed inside the specificclamp.* Install the temperature sensor at the same position.

Sensorfuse clamp

Accumulator

L Evaporator

(1) Remove the setscrews (2 pcs.)

Screw

B10-2007097_(11-24) 3/26/08, 2:41 PM23

– 24 –

REFRIGERATOR COMPARTMENT

L Damper

Damper

FreezerKnob

Deodorizerdevice

Neo-velt

Damperinsulation

Control P.C.B.

RefrigeratorKnob

Control Panel

B10-2007097_(11-24) 3/26/08, 2:41 PM24

– 25 –– 25 –

EXPLODED VIEWS

[EXPLODED VIEWS 11111]H2428

H0097

G30

E10

E10

G40

F0469

H0095

PW28

H0119

F0211

G0605

A0401

G0500

H3600

E0703

H0043

H3701

E38

G0600G0501

S0801

G0604

H1801

F0282H2914

F0228

S04

H0703

F0469

A9210

H2916

E08E07

S00

H2306

H2900

G50

H2428

G0138

F0241

F0813

A07

PW18

H2906

E16

B10-2007097_(26-37) 3/26/08, 2:42 PM25

– 26 –– 26 –

[EXPLODED VIEWS 22222]

GR-YG55DAA

B10-2007097_(26-37) 3/26/08, 2:42 PM26

– 27 –

[EXPLODED VIEWS 33333]

H3101

G0904

A94

G1314

F0713

G1105

H1204

H1807

E55H2007

H2663

H0608

H4701

B10-2007097_(26-37) 3/26/08, 2:42 PM27

– 28 –

H4006

G1312

F0235

H0025

H0701

F0836

H1501

H0921

H0011

[EXPLODED VIEWS 44444]

H0053

E35

F0249

H1622

H1320

A9641

B10-2007097_(26-37) 3/26/08, 2:42 PM28

– 29 –

[EXPLODED VIEWS 33333]

GR-YG55DAA

G0134

A9011

A9902

A9022

A9028

A9028

A9916

A9916

A90

G0109

G0108

G0101

H2207A41A21

H2207

A20A40

A9902

B10-2007097_(26-37) 3/26/08, 2:42 PM29

– 30 –

[EXPLODED VIEWS 77777]

[Detail AAAAA]

[Detail BBBBB]

(Include Air Duct Insulation)

G1101

H2637H0400

H0125 G1300

H2640

E9907

E53

E5203

H0914

E20

H0914

G0303

H0041

H2224

H2224

G14

E34

H0042

F0233

H0012

H0004

H0008

E0505

S09

E40

E41

E29S02

H0132

H0201

E5203

H0126

E5301

B10-2007097_(26-37) 3/26/08, 2:42 PM30

– 31 –

[EXPLODED VIEWS 55555]

PART PACKING

GR-YG55DAA

I0301

I06

I1513

I1513

I00

I01

I02

I02 I02

I0202

I0603

I02

I0602

B10-2007097_(26-37) 3/26/08, 2:42 PM31

– 32 –

_ Parts with this mark are safety part. These part are particularlyimportant for maintaining safety. When replacing, be sure to designate thepart code of the designated part.

PARTS LIST

_____ Location PART NO. DESCRIPTIONQ’TY/SET

No. GR-YG55DAA (GB)

A0401 44T41064 COVER, FRONT GRILLE 1A07 44T67019 COVER, REAR FRAME 1

A20 44T2AH85 DOOR, FREEZER 1

A21 44T2AG77 DOOR, REFRIGERATOR 1

A40 44T66014 GASKET DOOR, FREEZER 1

A41 44T66015 GASKET DOOR, REFRIGERATOR 1

A90 44T38084 POCKET, EGG 1

A9011 44T38083 POCKET, FREEZER 2

A9022 44T38082 POCKET, SMALL 1

A9028 44T38081 POCKET, BOTTLE, LARGE 2

A92 44T82015 CRISPER, VEGETABLE 1

A9210 44T95002 ROLLER, CRISPER 2

A94 44T71010 BOX, ICE STOCK 1

A9609 44T85059 SHELF, LOWER 1

A9614 44T85067 SHELF, FREEZER 1

A9621 44T85068 SHELF, FREEZER, UPPER 1

A9641 44T85069 SHELF, TANK 1

A9658 44T85061 SHELF, CRISPER 1

A9902 44T38080 PARTITION, EGG RACK, A 2

A9916 44T29002 STAND, TUBE, SMALL 2

_ E0505 44T52039 FUSE, TEMPERATURE (76°C) 1

_ E07 44T54010 RELAY, ELECTRICAL STARTER 1

_ E0702 44T60128 WIRING ASS’Y, PLASMA 1

_ E0703 44T60324 WIRE HARNESS, STARTER PTC/OL 1

_ E08 44T54002 RELAY, OVER LOAD 1

_ E10 44T52010 SWITCH, LAMP 2

_ E16 44055130 CAPACITOR, RUNNING 1

E20 44T50026 DAMPER, THERMOSTAT, REFREGERATOR 1

_ E29 44T57064 HEATER, GLASS TUBE 1

_ E34 44T59008 MOTOR, FAN 1

_ E35 44T59004 MOTOR, WATER SUPPLY PUMP 1

_ E38 44T60232 POWER CORD 1

_ E40 44062052 SENSOR, FREEZER 1

_ E41 44062050 SENSOR, DEFROST 1

_ E4810 44T60164 LEAD WIRE ASS’Y, GROUND 1

_ E4811 44T60233 WIRE ASS’Y, FANMOTOR 1

_ E4814 44T60129 WIRE ASS’Y, C 1

_ E5203 44058086 LAMP, REFRIGERATOR 2

_ E53 44T60300 SOCKET, LAMP 1

_ E5301 44T60301 SOCKET, LAMP,I 1

E55 44T73002 PUMP, WATER SUPPLY 1

_ E9907 44T60135 CONTROLLER, P.C.B 1

F0211 44041452 HOLDER, FRONT COVER 2

F0228 44049137 HOLDER, PIPE 1

F0233 44067570 HOLDER, DEFROST SENSOR 1

F0235 44T67020 HOLDER, SENSOR (ICE MAKER) 1

F0241 44T67021 HOLDER, P.C BOARD 1

B10-2007097_(26-37) 3/26/08, 2:42 PM32

– 33 –

_ Parts with this mark are safety part. These part are particularlyimportant for maintaining safety. When replacing, be sure to designate thepart code of the designated part.

PARTS LIST

_____ Location PART NO. DESCRIPTIONQ’TY/SET

No. GR-YG55DAA (GB)

F0249 44T67022 HOLDER, TANK, B 1

F0282 44T49010 HOLDER, EVAPORATING PIPE 1

F0299 44T67037 HOLDER, MEAT PAN 2

F0469 44T96023 SUPPORTER, MEAT PAN 2

F0713 44T96013 PLATE, CEILING, CHILLED CASE 1

F0740 44T96014 PLATE, CEILING, ICE ROOM 1

F0813 44T67023 PLATE, HOLDER, ELECTRICAL PARTS 1

F0836 44T96012 PLATE, PUSHER, SENSOR 1

G0101 44T09032 STOPPER, DOOR UPPER 1

G0108 44T09037 STOPPER, DOOR, A 1

G0109 44T09038 STOPPER, DOOR 1

G0134 44T09036 STOPPER, A 1

G0138 44T96009 STOPPER, SHELF, LEFT 1

G0303 44068412 SPRING, FAN 1

G0500 44048718 CASTER 2

G0501 44T42007 CASTER, FRONT 2

G0600 44049288 LEG, ADJUSTABLE 2

G0604 44T48002 LEG, FRONT, LEFT 1

G0605 44T48003 LEG, FRONT, RIGHT 1

G0803 44048691 RUBBER, VIBRATION-PROOF, EVA-PIPE 1

G0904 44T49007 MAT, SOUND-PROOF, ICE BOX 1

_ G1101 44T56010 PLASMA, DEODORIZER 1

_ G1105 44T73003 ICE, MAKER 1

G1300 44T10070 DUCT, AIR 1

G1312 44T73004 DUCT, ICE MAKER 1

G1314 44T73005 DUCT, CEILING 1

G14 44059190 FAN, PROPELLER 1

G30 44T65020 HINGE, UPPER 1

G40 44T65023 HINGE, LOWER 1

G50 44T65022 HINGE, MIDDLE 1

H0004 44T18032 COVER, EVAPORATOR 1

H0008 44T18049 COVER, EVAPORATOR, MIDDLE 1

H0011 44T96018 COVER, OUTLET, WATER SUPPLY 1

H0012 44T18026 COVER, EVAPORATOR, FREEZER 1

H0025 44T67024 COVER, SENSOR ICE MAKER 1

H0041 44T67058 COVER, FAN MOTOR, REAR 1

H0042 44T67033 COVER, FAN MOTOR, FRONT 1

H0043 44067608 COVER, RELAY 1

H0053 44T73006 COVER, DRAIN OUTLET 1

H0095 44T58015 COVER, LED 1

H0097 44T18072 COVER, HINGE UPPER 1

H0119 44T18068 COVER, FIXER 1

H0125 44T58012 COVER, LAMP 1

H0126 44T58006 COVER, LAMP, FREEZER 1

H0132 44T67068 COVER, CEILING 1

H0201 44T58008 CASE, LAMP 1

H0205 44T80026 TRAY, CHILLED 1

B10-2007097_(26-37) 3/26/08, 2:42 PM33

– 34 –

_ Parts with this mark are safety part. These part are particularlyimportant for maintaining safety. When replacing, be sure to designate thepart code of the designated part.

PARTS LIST

_____ Location PART NO. DESCRIPTIONQ’TY/SET

No. GR-YG55DAA (GB)

H0307 44T80040 DOOR, CHILLED CASE 1

H0400 44T72042 PANEL, CONTROL 1

H0608 44T73008 LID, TANK, WATER SUPPLY 1

H0701 44T80020 TRAY, ICE MAKER 1

H0703 44T80029 PAN, VAPORIZE 1

H0914 44T18078 INSULATION, DAMPER 1

H0921 44T73020 INSULATION, INLET, WATER SUPPLY 1

H1204 44T96030 PARTITION PLATE, FREEZER 1

H1209 44T96026 PARTITION PLATE, CRISPER 1

H1318 44T96024 RAIL, CRISPER, LEFT 1

H1319 44T96025 RAIL, CRISPER, RIGHT 1

H1320 44T96031 RAIL, DOOR TANK 1

_ H1501 44T73024 HOSE, WATER SUPPLY 1

H1622 44T73010 CASE, WATER SUPPLY 1

H1801 44070321 CAP, VALVE 1

H1802 44T87016 CAP, SCREW 2

H1807 44T73011 CAP, SLIDE 1

H1905 44067643 TUBE, WIRE 1

H2007 44T73012 PIPE, SUCKING WATER SUPPLY 1

H2207 44T29006 BUSHING, DOOR, UPPER 2

H2224 44067596 BUSHING, MOTOR 2

H2306 44067385 WASHER, CUSHION 4

H2428 44087012 SCREW, FIX MIDDLE HINGE 5

H2433 44T87002 SCREW, FIX TIMER BOX 2

H2514 44048565 RIVET, PUSH 1

H2637 44T61016 KNOB, CONTROL SWITCH 1

H2640 44T61015 KNOB, DAMPER 1

H2663 44T96019 LEVER, LID 1

H2900 44T67018 CUSHION, RUBBER 4

H2906 44T48004 RUBBER, SOUND INSULATION, SMALL 2

H2914 44049007 RUBBER, PIPE HOLDER 1

H2916 44T49018 RUBBER, PIPE HOLDER, SMALL 1

H3101 44T73013 PANEL, ICE MAKER 1

H3600 44T42010 BASE, COMPRESSOR 1

H3701 44067604 FASTENER, RELAY 1

H4006 44T73014 ARM, DETECTION 1

H4101 44T40015 NAME PLATE 1

H4300 44T2C039 BADGE, DOOR 1

H4701 44T73015 TANK, WATER SUPPLY 1

I00 44T9A219 CARTON BOX 1

I01 44T9A215 BOTTOM BASE 1

I02 44T9A216 CUSHION KIT PACKING 1

I0202 44T9A072 CUSHION FRONT, PACKING 1

I0301 44T9A078 POLYETHYLEN BAG SQUARE TYPE 1

I06 44T9A217 ACKING CASE UPPER 1

I0602 44T9A073 CUSHION, PACKING CORNER 1

I0603 44T9A218 PACKING, HOLDER CASE 1

B10-2007097_(26-37) 3/26/08, 2:42 PM34

– 35 –

_ Parts with this mark are safety part. These part are particularlyimportant for maintaining safety. When replacing, be sure to designate thepart code of the designated part.

PARTS LIST

_____ Location PART NO. DESCRIPTIONQ’TY/SET

No. GR-YG55DAA (GB)

I10 44T84382 OWNER’S MANUAL 1

I1513 44T17E12 LABEL, CODE 2

_ PW18 44T60325 PRINTED, CIRCUIT BOARD, RELAY 1

_ PW28 44T60273 PRINTED CIRCUIT BOARD, LED PCB 1

_ S00 44T0C047 COMPRESSOR, FL1462-SM 1

S02 44T44027 EVAPORATOR 1

S04 44045053 DRYER, 10G 1

S0801 44T43019 PIPE, EVAPORATE 1

S09 44T49011 ACCUMULATOR 1

S1408 44T47002 PIPE, AUXILIARY 1

B10-2007097_(26-37) 3/26/08, 2:42 PM35

– 36 –

MEMO

B10-2007097_(26-37) 3/26/08, 2:42 PM36

– 37 –

MEMO

B10-2007097_(26-37) 3/26/08, 2:42 PM37

TOSHIBA CONSUMER PRODUCTS (THAILAND) CO., LTD.144/1 MOO 5, BANGKADI, AMPHUR MUANG, PATHUMTHANI 12000, THAILAND

B10-2007097_(Cover) 3/26/08, 2:43 PM2