-
Note : Dimension is with boom angle at -1.5 degree.
GENERAL DIMENSIONS
Turning radius (26.5R25☆☆ Tires)6 wheel steer2 wheel steer
32' 6"48'11"
SPEC. SHEET NO. GR-1600-3-00104/ES-01
Overall lengthOverall widthOverall heightCarrier lengthfor
traveling
53' 1-3/8"10'10-1/2"12' 5"
27' 1-1/4"
approx. 16,190approx. 3,315approx. 3,785
approx. 8,260
Feet
9.914.9
Meter FeetMeter
OPTIONAL WEIGHT 11.1 t (24,500 lbs)
5,50
0 (1
8'1/
2")
7,30
0 (2
3'11
-3/8
")8,
200
(26'
10-7
/8")
2,99
0 (9
'9-3
/4")
4,860 (15'11-1/8")4,165 (13'8")
4,520 (14'10") 4,505 (14'9-1/4")4,600 (15'1")
13,050–61,000 (42'9-3/4"–200'1-1/2")2,400 (7'10-3/8")
3,78
5 (1
2'5"
)
11.9
º
16.2
º
3,500 (11'5-3/4")
12.6
º
17.4
º
2,010 (6'7-1/8") 1,100 (3'7-1/4")
10,155 (33'3-3/4")2,000 (6'6-3/4") 2,145 (7'1/4")4,000
(13'1-1/2")8,045 (26'4-7/8")
16,190 (53'1-3/8")
2,599 (8'6-1/4")
3,315 (10'10-1/2")
(φ1'
10-1
/2")
5
70
GR-1600XL(Left-hand drive)
160 Ton (145 Metric Ton) Capacity
HYDRAULIC ROUGH TERRAIN CRANE
DIMENSIONS
Speci�cations are subject to change without notice.
-
-2 -
SPEC. SHEET NO. GR-1600-3-00104/ES-01
BOOM6 sections boom of round box construction with 7 sheaves at
boom head, extended by single telescoping cylinder.2 easily
removable wire rope guards, rope dead end provided on both sides of
boom head. Boom telescope sections are supported by wear pads both
vertically and horizontally. Fully retracted length....... 13.1 m
(42.8') Fully extended length ...... 61.0 m (200.1') Extension
speed.............. 47.9 m (157.3') in 450 s Sheave root diameter
...... 0.400 m (15-3/4")
BOOM ELEVATIONBy a double acting hydraulic cylinder with holding
valve. Boom angle indicator.Automatic speed reduction and slow stop
function. Boom angle ..................... -1.5–81.5º Boom raising
speed ........ 20º to 60º in 28 s
JIB2 stage bi-fold lattice type, offset angle (5–40º) by tilt
cylinder.Single sheave at the head of both jib sections. Stowed
alongside base boom section. Assistant cylinders for mounting and
stowing, controlled at right side of superstructure.Self stowing
jib mounting pins. Length ............................. 10.3 m,
18.0 m (33.8', 59.1') Offset............................... 5–40˚
Sheave root diameter ...... 0.440 m (17-5/16")
INSERT JIB (OPTION)Insert lattice jib can be used for reaching
higher place. Length .................. 7.0 m (1 pce.), 14.0 m (2
pcs.), (23.0', 45.9')
SHORT JIB (OPTION)2 sheaves, heavy lifting jib can be used for
lifting lifting heavy load in tight spaces. Length
............................ 3.6 m (11.8')
Offset.............................. 20º, 40º Sheave root diameter
..... 0.419 m (16-1/2")
AUXILIARY LIFTING SHEAVE (SINGLE TOP)Single sheave, mounted to
main boom head for single line work (stowable). Root
diameter.................. 0.440 m (17-5/16")
ANTI-TWO BLOCK DEVICEPendant type over-winding cut out device
with audio-visual (FAILURE lamp/BUZZER) warning system.
SLEWINGHydraulic axial piston motor driven through planetary
slewing speed reducer. Continuous 360º full circle slewing on ball
bearing turn table at 1.3min-1 {rpm}. Equipped with manually
locked/released slewing brake. A 360º positive swing lock manually
engaged in cab. Twin slewing system: Free slewing or lock slewing
controlled by selector switch on front console. Slewing
speed................. 1.3 min-1 {rpm}
COUNTERWEIGHTStandard weight ...................18,200 kg
(40,100 lbs)Extra weight right (option) ..... 5,550 kg (12,250
lbs)Extra weight left (option)........ 5,550 kg (12,250 lbs)
WINCHMAIN WINCHVariable speed type with grooved drum driven by
hydraulic axial piston motor through speed reducer. Power load
lowering and raising. Equipped with automatic brake (neutral brake)
and counterbalance valve. Controlled independently of auxiliary
winch. Equipped with cable follower and drum rotation
indicator.
MAIN DRUM Root diameter x wide ............. 0.382 m (15") x
0.742 m (29-1/4") Wire rope diameter x length ........ 19 mm (3/4")
x 320 m (1,050') Drum capacity
........................................ 394 m (1293'), 7 layers
Maximum single line pull (1st layer).............9,900 kg (21,800
lbs) Maximum permissible linepull wire strength...7,200 kg (15,900
lbs)
AUXILIARY WINCHVariable speed type with grooved drum driven by
hydraulic axial piston motor through speed reducer.Power load
lowering and raising. Equipped with automatic brake (neutral brake)
and counterbalance valve. Controlled independently of main winch.
Equipped with cable follower and drum rotation indicator.
AUXILIARY DRUM Root diameter x wide ............. 0.382 m (15")
x 0.742 m (29-1/4") Wire rope diameter x length ........... 19 mm
(3/4") x 225 m (738') Drum capacity
........................................ 394 m (1293'), 7 layers
Maximum single line pull (1st layer).............9,900 kg (21,800
lbs) Maximum permissible linepull wire strength...7,200 kg (15,900
lbs)
WIRE ROPENon-rotating 19 mm (3/4") 7x35 class.Breaking Strength
36,000 kg (79,400 lbs)
HOOK BLOCKS100 metric ton (110 ton, option) .... 7 sheaves with
hook block and
safety latch.45 metric ton (50 ton, option) ........ 3 sheaves
with hook block and
safety latch.7.2 metric ton (7.9 ton, option) ...... Weighted
hook with swivel and
safety latch.
HYDRAULIC SYSTEMPUMPS2 variable piston pumps for crane
functions.Tandem gear pump for steering, swing and optional
equipment. Powered by carrier engine. Pump disconnect for crane
isengaged/ disengaged by rotary switch from operator's cab.
CONTROL VALVESMultiple valves actuated by pilotpressure with
integral pressure relief valves.
RESERVOIR763 lit. (202 gallon) capacity. External sight level
gauge.
FILTRATIONBETA10=10 return �lter, full �ow with bypass
protection, located inside of hydraulic reservoir. Accessible for
easy replacement.
OIL COOLERAir cooled fan type.
CAB AND CONTROLSBoth crane and drive operations can be performed
from onecab mounted on rotating superstructure.
15º tilt, Left side, 1 man type, steel construction with sliding
door access and safety glass windows opening at side. Door window
is powered control. Windshield glass window and roof glass window
are shatter-resistant. Tilt-telescoping steering wheel. Adjustable
control lever stands for swing, boom elevating, boom telescoping,
auxiliary winch and main winch. Control lever stands can change
neutral positions and tilt for easy access to cab. 3 way adjustable
operator's seat with high back, headrest and armrest. Engine
throttle knob. Foot operated controls: boom elevating boom
telescoping, service brake and engine throttle. Hot water cab
heater and air conditioning.
Dash-mounted engine start/stop, monitor lamps, cigarettelighter,
drive selector switch, parking brake switch, steering mode select
switch, power window switch, pump engaged/ disengaged switch, swing
brake switch, telescoping/auxiliary winch select switch, outrigger
controls, free swing / lock swing selector switch, eco mode switch,
high speed winch (main/aux) switch and ashtray.
Instruments - Torque converter oil temperature, engine
watertemperature, air pressure, fuel, speedometer, tachometer, hour
meter and odometer / tripmeter. Hydraulic oil pressure is monitored
and displayed on the AML-C display panel.
-
-3 -
SPEC. SHEET NO. GR-1600-3-00104/ES-01
CRANE SPECIFICATIONS
CARRIER SPECIFICATIONS
Tadano electronic LOAD MOMENT INDICATOR system(AML-C)
including:
• Control lever lockout function with audible and visual
pre-warning
• Boom position indicator• Outrigger state indicator• Boom angle
/ boom length / jib offset angle / jib length / load
radius / rated lifting capacities / actual loads read out• Ratio
of actual load moment to rated load moment indication• Automatic
speed reduction and slow stop function on boom
elevation and slewing• Working condition register switch• Load
radius / boom angle / tip height / slewing range preset
function• External warning lamp• Tare function• Fuel consumption
monitor• Main winch / auxiliarly winch select• Drum rotation
indicator (audible and visible type) main and
auxiliary winch
TADANO AML-C monitors outrigger extended length and
automatically programs the corresponding "RATED LIFTING CAPACITIES"
table.
Operator's right hand console includes transmission gear
selector and sight level bubble. Upper console includes working
light switch, roof washer and wiper switch emergency outrigger set
up key switch, jib equipped/removed select switch, eco mode switch,
high speed winch (main / aux) switch, Cab tilt switch. Slewing lock
lever.
NOTE: Each crane motion speed is based on unladen
conditions.
TYPERear engine, left hand steering, driving axle 2-wayselected
type by manual switch, 6x2 1st drive, 6x4 1st and 3rd drive.
FRAMEHigh tensile steel, all welded mono-box construction.
ENGINEModel MITSUBISHI 6M60-TL (Tier2)Type Direct injection
dieselNo. of cylinders 6Combustion 4 cycle, turbo charged and after
cooledBore x Stroke, mm. (in) 118 x 115 (4.646 x
4.528)Displacement, liters (cu. in) 7.54 (460)Air inlet heater 24
volt preheatAir cleaner Dry type, replaceable elementOil �lter Full
�ow with replaceable elementFuel �lter Full �ow with replaceable
elementFuel tank, liters (gal.) 300 (79.2), right side of
carrierCooling Liquid pressurized, recirculating by-passRadiator
Fin and tube core, thermostat controlledFan, mm (in.) Suction type,
6-blade, 600 (23.6) dia.Starting 24 voltCharging 24 volt system,
negative groundBattery 2-120 amp. HourCompressor, air, l /min (CFM)
830 (29) at 2,600 rpmOutput, Max. kW (HP) Gross 200 (267) at 2,600
rpmTorque, Max. Nm (ft-lb) 785 (579) at 1,400 rpmCapacity, liters
(gal.)
Cooling water 13 (3.4)Lubrication 13–15 (3.4–4.0)Fuel 300
(79.2)
TRANSMISSIONElectronically controlled full automatic
transmission. Torque converter driving full powershift with driving
axle selector. 5 forward and 2 reverse speeds, constant mesh.
2 speeds - high range - 2 wheel drive; 4 wheel drive3 speeds -
low range - 4 wheel drive
TRAVEL SPEED15 km/h (9.3 mph) with counterweight4 km/h (2.5 mph)
without counterweight
GRADE ABILITY (tanθ) - 44% (with counterweight 29.3 t (64,600
lbs)), 52% (with counterweight 18.2 t (40,100 lbs)), 30%** Machine
should be operated within the limit of engine crankcase
design (17º: MITSUBISHI 6M60-TL).
AXLE1st: Full �oating type, steering and driving axle with
planetary reduction and open differential. 2nd: Steering and not
driving axle.3rd: Full �oating type, steering and driving axle with
planetary reduction and open differential.
STEERINGHydraulic power steering controlled by steering wheel.
Four steering modes available: 2 wheel front, 4 wheel rear, 6 wheel
coordinated and 6 wheel crab.
SUSPENSION1st: Rigid mounted to frame. 2nd and 3rd:
"Hydro-Pneumatic suspension cylinders" with
levering adjustment and oscillation.
BRAKE SYSTEMSService: Air over hydraulic disc brakes onall 6
wheels. Parking/Emergency: Spring applied-air released brake acting
on input shaft of 1st and 3rd axle. Auxiliary: Electro- pneumatic
operated exhaust brake.
TIRES - 26.5R25☆☆ Air pressure: 650 kPa (94 psi)
OUTRIGGERSFour hydraulic, beam and jack outriggers.Vertical jack
cylinders equipped with integral holding valve. Each outrigger beam
and jack is controlled independently from cab.Beams extend to 8.2 m
(26'10-7/8") center-line and retract to within 3.315 m (10'
10-1/2") overall width with �oats.Outrigger boxes are
self-removable for ease of transportation. Outrigger jack �oats are
attached thus eliminating the need of manually attaching and
detaching them. Controls and sight bubble located in superstructure
cab. Four outrigger extension lengths are provided with
corresponding "RATED LIFTING CAPACITIES" for crane duty in con�ned
areas.Min. Extension 2.99 m (9' 9-3/4") center to centerMid.
Extension 5.50 m (18' 1/2") center to centerMid. Extension 7.30 m
(23'11-3/8") center to centerMax. Extension 8.20 m (26'10-7/8")
center to centerFloat size (Diameter) 0.57 m (1'10-1/2")
-3 -
-
STANDARD EQUIPMENT- Six section extended boom by single
telescoping cylinder
13.1 m–61.0 m (42.8'–200.1')- 10.3 m (33.8') or 18.0 m (59.1')
bi-fold lattice jib, offset angle (5–40º)
by tilt cylinder.- Quick reeving type bi-fold jib- Anti-Two
block device (overwind cutout)- Mirror for main and auxiliary
winch- Work lights- Variable speed main winch with grooved drum,
cable follower and
320 m of 19 mm (1050' of 3/4") cable.- Variable speed auxiliary
winch with grooved drum, cable follower and
225 m of 19 mm (738' of 3/4") cable.- Drum rotation indicator
(audible,visible and thumper type) main and
auxiliary winch- Auxiliary lifting sheave (single top) stowable-
2-speed winch- Tadano twin swing system and 360º positive swing
lock- Positive control- Hydraulic oil cooler- 15º tilt cab- 3 way
adjustable cloth seat with armrests, high back and seat belt-
Tilt-telescoping steering wheel- Tinted safety glass and sun visor-
Front windshield wiper and washer- Roof window wiper and washer-
Power window (cab door )- Cigarette lighter and ashtray- Cab �oor
mat- Pump disconnect in operator's cab- Air conditioner (hot water
heater and cooler)- Full instrumentation package- Self centering
�nger control levers with pilot control- Control pedals for boom
elevating and boom telescoping- Low oil pressure/high water temp.
warning device (visual)- 2nd and 3rd steer centering light- Air
cleaner dust indicator- Tadano electronic load moment indicator
system (AML-C)- Tare function
- Boom angle indicator- Outrigger extension length detector-
Electronic crane monitoring system- Rear view mirrors (right and
left side)- Fenders- Air dryer- Complete highway light package-
Towing hooks-Front and rear- Hook block tie down (front bumper)-
Weighted hook storage compartment- Halogen head lamp-
Self-removable outrigger boxes- Independently controlled
outriggers- Four outrigger extension positions- Self-storing
outrigger pads- Electronic controlled automatic transmission driven
by torque
converter- 6 x 4 x 6 drive/steer- 1st axle: open differential-
3rd axle: open differential- Automatic rear axle oscillation
lockout system- 26.5R25☆☆ tires- Disc brakes- Water separator with
�lter (high �ltration)- Back-up alarm- 24 volt electric system-
Tool storage compartment- Tire in�ation kit- Mitsubishi 6M60-TLA3B
turbo charged after cooled engin (267HP)
with exhaust brake- Engine over-run alarm- Lifting eyes- Fuel
consumption monitor- Eco mode system- Self-removable
counterweight
OPTIONAL EQUIPMENT
LINE SPEEDS AND PULLS DRUM WIRE ROPE CAPACITIES
- Additional weight 11.1 t (24,500 lbs)- Removable boom system-
Working lamp with remort controller- Boom and jib mounted aircraft
warning light- Wind speed indicator- Emergency steering system-
Over-unwinding prevention- Insert jib- Short jib
- 100 metric ton (110 ton) - 7 sheaves with hook block and
safety latch- 45 metric ton (50 ton) - 3 sheaves with hook block
and safety latch- 7.2 metric ton (7.9 ton) - Weighted hook with
swivel and safety latch- Telematics (machine data logging and
monitoring system) with
HELLO-NET via internet (availability depends on countries)-
Outrigger load display and warning- Inclinometer (electronic
inclination indicator)
HOISTING PERFORMANCE
- Maximum permissible line pull wire strength.7,200 kg (15,900
lbs) with 7 x 35 class rope.
1 Line speed based only on hook block, not loaded.2 Developed by
machinery with each layer of wire rope, but not based
on rope strength or other limitations in machinery or
equipment.3 Seventh layer of wire rope are not recommended for
hoisting
operations.
LayerLine speeds1 Line pulls Available2
1st2nd3rd4th5th6th
7th3
Lbs.21,80019,90018,20016,80015,60014,60013,700
kgf9,9009,0108,2707,6407,0906,6206,210
F.P.M253276299318341361384
m/min77849197104110117
F.P.M354384413446476505535
m/min108117126136145154163
DRUM DIMENSIONS (Main and auxiliary)
Root diameterLengthFlange diameter
Inch15
29-1/426-5/8
mm382742677
Wireropelayer
Total wire ropeRope per layer
Main or auxiliary winch - 0.382 m (15") drum Main and auxiliary
drum grooved lagging19 mm (3/4") wire rope
1234567
Meter44.848.652.556.360.163.967.7
Meter44.893.4
145.9202.2262.3326.2393.9
Feet147.0159.4172.2184.7197.2209.6222.1
Feet147.0306.4478.7663.4860.6
1070.21292.3
LowLow High
-4 -
SPEC. SHEET NO. GR-1600-3-00104/ES-01
-
BOOM
SINGLE TOP
JIB
Hydraulic offset jibCounterweight 29.3 t
0.6 m
Approx.2.6 m
Approx. 3.3 m
Approx.2.3 m
LIFT
ING
HE
IGH
T (m
)
LOAD RADIUS (m)
85
80
75
70
65
60
55
50
45
40
35
30
25
20
15
10
5
050 10 15 20 25 30 35 40 45 50 55 60 65
16°
30°
40°
50°
33°
45°
10°
0°
20°
61.0-m Boom
57.0-m Boom
52.6-m Boom48.2-m Boom
43.8-m Boom39.4-m Boom
35.0-m Boom30.6-m Boom
26.2-m Boom21.8-m Boom
17.4-m Boom13.1-m Boom
81.5°
70°
60°
61.0-m Boom + 18.0-m JIB
61.0-m Boom + 10.3-m JIB
40°20°5°
-5 -
GR-1600XL WORKING RANGE CHARTSPEC. SHEET NO.
GR-1600-3-00104/ES-01
NOTE: Boom and jib geometry shown are for unloaded condition and
machine standing level on �rm supporting surface.Boom de�ection and
subsequent radius and boom angle change must be accounted for when
applying load to hook.
-
BOOM
SINGLE TOP
JIB
Hydraulic offset jib
Counterweight 29.3 t
Approx.2.6 m
Approx. 3.3 m
Approx.2.3 m
0.6 m
7.0 m Insert jib *Option
LIFT
ING
HE
IGH
T (m
)
LOAD RADIUS (m)
NOTE: Boom and jib geometry shown are for unloaded condition and
machine standing level on �rm supporting surface.Boom de�ection and
subsequent radius and boom angle change must be accounted for when
applying load to hook.
61.0-m Boom 48°
50°
60°
70°
81.5°
61.0-m Boom + 7.0-m INSERT JIB + 18.0-m JIB
85
80
75
70
60 0
5
10
15
20
25
30
35
40
45
50
55
60
65
555045403530252015100 5 65
90
40°20°5°
-6 -
GR-1600XL WORKING RANGE CHARTSPEC. SHEET NO.
GR-1600-3-00104/ES-01
-
Hydraulic offset jib 14.0 m Insert jib *OptionCounterweight 29.3
t
BOOM
SINGLE TOP
JIB
Approx.2.6 m
Approx. 3.3 m
Approx.2.3 m
0.6 mLIFT
ING
HE
IGH
T (m
)
LOAD RADIUS (m)
NOTE: Boom and jib geometry shown are for unloaded condition and
machine standing level on �rm supporting surface.Boom de�ection and
subsequent radius and boom angle change must be accounted for when
applying load to hook.
61.0-m Boom
55°
58°
60°
61.0-m Boom + 14.0-m INSERT JIB + 18.0-m JIB
81.5°
70°
5°
40°20°
85
90
85
80
75
70
60 0
5
10
15
20
25
30
35
40
45
50
55
60
65
555045
90
65403530252015100 5
-7 -
GR-1600XL WORKING RANGE CHARTSPEC. SHEET NO.
GR-1600-3-00104/ES-01
-
NOTE: Boom and jib geometry shown are for unloaded condition and
machine standing level on �rm supporting surface.Boom de�ection and
subsequent radius and boom angle change must be accounted for when
applying load to hook.
BOOM
SINGLE TOP
JIB
Short jib *OptionCounterweight 29.3 t
Approx.2.6 m
Approx. 3.3 m
Approx.2.3 m
0.6 m
LIFT
ING
HE
IGH
T (m
)
LOAD RADIUS (m)
50 10 15 20 25 30 35 40 6545 50 55
65
60
55
50
45
40
35
30
25
20
15
10
5
060
70
61.0-m Boom + 3.6-m JIB
81.5°
70°
50°
60°
40°
30°
20°
40°
-8 -
GR-1600XL WORKING RANGE CHARTSPEC. SHEET NO.
GR-1600-3-00104/ES-01
-
-9-
GR-1600XL RATED LIFTING CAPACITIES (IN METRIC TON)SPEC. SHEET
NO. GR-1600-3-00104/ES-01
13.1 m 17.4 m 21.8 m 26.2 m 30.6 m 35.0 m 39.4 m 43.8 m 48.2 m
52.6 m 57.0 m 61.0 m
**145.0*110.6*101.5
93.685.979.373.568.363.759.656.052.746.837.3
90.790.790.790.183.778.173.268.364.160.056.453.147.341.737.133.427.8
79.079.079.079.079.075.871.066.763.660.256.553.247.541.937.333.527.623.321.3
37.066.066.066.066.066.063.560.557.855.352.947.241.637.534.328.424.020.618.416.3
37.048.248.248.248.248.248.248.248.044.841.637.733.928.024.321.318.516.114.112.3
8.2
35.235.238.737.535.935.235.235.235.233.231.528.424.320.918.115.713.612.811.410.1
8.4
30.130.130.129.527.926.224.422.720.919.317.816.515.414.112.310.8
9.68.57.66.8
22.123.923.922.922.021.019.217.115.414.012.711.710.810.0
9.28.67.97.16.45.8
17.218.918.918.416.915.514.312.911.810.810.1
9.48.88.27.46.66.15.85.34.8
13.515.015.015.014.113.112.111.210.4
9.68.88.27.77.36.96.35.65.04.54.13.72.8
12.012.012.012.011.210.4
9.89.18.58.07.47.06.55.85.24.64.13.73.22.82.52.2
10.410.410.410.2
9.69.08.47.87.36.76.25.85.45.04.64.13.63.22.82.42.11.8
**Over front with special equipment *With special Equipment
AB
A: Boom length (m)B: Load radius (m)
Boom
NOTE: In this table, the thick line which divides strength area
and stability area is not shown because the �gure of this table is
indicated the best performance at the same boom length among the
plural telescopic boom patterns.
COUNTERWEIGHT 29.3 t (64,600 lbs)ON OUTRIGGERS FULLY EXTENDED
8.2 m (26'10-7/8'') SPREAD
360º ROTATION (Unit: x 1,000 kg)
2.503.003.504.004.505.005.506.006.507.007.508.009.00
10.0011.0012.0014.0016.0018.0020.0022.0024.0026.0028.0030.0032.0034.0036.0038.0040.0042.0044.0046.0048.0050.0052.0054.0056.00
(42.8') (57.2') (71.6') (86.1') (100.5') (114.9') (129.3')
(143.7') (158.1') (172.5') (187.0') (200.1')
-
GR-1600XL RATED LIFTING CAPACITIES (IN METRIC TON)SPEC. SHEET
NO. GR-1600-3-00104/ES-01
81.58180797877767573706865636058555350484543403835333028252320G
RC
W R W R
W14.715.617.218.820.521.923.324.527.331.033.537.239.242.544.547.249.251.653.355.656.958.960.161.662.764.0
5.55.55.55.55.55.45.25.04.84.34.13.83.63.33.12.82.72.42.22.01.81.61.41.11.00.8
17.418.619.921.222.624.425.326.729.333.035.438.840.943.846.048.650.452.854.356.457.859.560.762.163.0
5.55.55.45.25.04.94.74.64.44.03.83.63.43.13.02.72.62.32.11.91.81.51.31.10.9
20.421.122.624.025.226.527.828.931.334.837.040.142.245.147.049.651.153.454.856.8
5.15.04.94.74.64.54.44.24.03.83.63.43.33.02.92.72.52.22.11.9
COUNTERWEIGHT 29.3 t (64,600 lbs)ON OUTRIGGERS FULLY EXTENDED
8.2 m (26'10-7/8") SPREAD
360º ROTATION61.0-m (200.1') Boom + 10.3-m (33.8') Hydraulic
offset jib
20º Tilt 40º Tilt5º Tilt
81.58180797877767573706865636058555350484543403835333028252320G
RC
W R W R
W12.913.715.216.718.219.620.822.124.628.230.633.836.139.141.243.945.648.249.651.753.155.056.257.858.860.261.062.162.763.5
6.26.26.26.26.26.26.05.85.45.04.74.34.23.93.73.53.33.12.92.62.42.22.01.71.61.31.21.11.00.9
15.716.517.919.320.621.923.224.326.830.332.435.637.740.642.545.246.949.250.652.754.055.756.858.359.260.461.262.0
6.26.26.15.95.75.65.45.24.94.64.34.03.93.73.53.33.22.92.82.52.42.11.91.61.51.31.21.0
18.719.320.621.923.024.325.426.628.932.134.237.139.041.943.746.147.749.951.253.1
5.85.75.55.45.25.14.94.84.64.34.13.83.73.53.43.23.12.92.72.5
57.0-m (187.0') Boom + 10.3-m (33.8') Hydraulic offset jib20º
Tilt 40º Tilt5º Tilt
81.58180797877767573706865636058555350484543403835333028252320G
RC
W R W R
W11.312.013.414.816.117.518.819.622.025.727.931.033.236.037.840.442.044.445.948.049.351.152.253.754.755.956.857.858.459.2
7.27.27.27.27.27.27.26.96.55.95.65.25.04.64.44.13.93.73.53.23.02.72.52.22.01.71.61.41.31.2
14.315.016.317.618.819.921.122.324.427.629.832.734.637.539.241.743.345.546.948.850.051.752.854.255.156.357.057.9
7.27.27.27.06.86.66.46.25.85.45.24.84.64.44.23.93.83.53.33.02.92.62.42.11.91.71.51.4
17.418.019.220.321.422.523.624.626.729.631.634.336.138.840.442.744.146.147.449.3
6.86.76.56.36.15.95.85.65.45.04.84.54.44.24.03.83.63.43.23.0
COUNTERWEIGHT 29.3 t (64,600 lbs)ON OUTRIGGERS FULLY EXTENDED
8.2 m (26'10-7/8") SPREAD
360º ROTATION52.6-m (172.5') Boom + 10.3-m (33.8') Hydraulic
offset jib
20º Tilt
1
40º Tilt5º Tilt
81.58180797877767573706865636058555350484543403835333028252320G
RC
W R W R W
11.813.415.617.219.320.722.824.126.027.229.030.131.732.734.135.136.537.238.439.039.940.541.2
12.812.211.310.810.19.69.08.78.27.97.67.47.17.06.86.66.56.46.36.05.75.65.4
8.99.3
10.110.911.912.613.314.115.617.919.321.422.824.826.027.929.030.731.733.234.235.436.337.538.239.239.840.5
10.610.510.210.09.79.59.39.18.78.27.97.67.47.16.96.76.56.46.36.16.16.05.95.95.85.85.85.6
11.311.712.513.214.014.815.516.217.619.721.022.924.226.027.228.929.931.432.433.8
7.37.27.17.06.96.96.86.76.56.36.26.16.05.95.85.75.75.75.65.6
35.0-m (114.9') Boom + 10.3-m (33.8') Hydraulic offset jib20º
Tilt
2
1 1
40º Tilt5º Tilt
- 10 -
Jib
C: Loaded boom angle (º)R: Load radius (m)W: Rated lifting
capacity (Unit: x 1,000 kg)G: Number of parts of line
-
GR-1600XL RATED LIFTING CAPACITIES (IN METRIC TON)SPEC. SHEET
NO. GR-1600-3-00104/ES-01
81.58180797877767573706865636058555350484543403835333028252320G
RC
W R
1 1
1 1
W R
W17.118.019.921.623.425.026.828.531.435.638.442.144.748.450.553.755.658.359.962.463.965.8
3.73.73.73.73.73.73.73.73.53.23.12.82.72.52.32.11.91.71.51.31.20.9
22.022.724.726.327.929.330.932.335.039.041.345.347.550.852.955.857.560.061.463.765.066.8
3.73.73.73.73.63.53.43.33.12.92.72.62.52.32.22.01.81.61.41.21.10.8
27.128.029.631.132.534.035.336.439.242.644.948.150.353.355.157.659.161.162.564.3
3.23.23.13.13.03.03.02.92.82.62.52.42.32.22.11.91.71.51.41.1
COUNTERWEIGHT 29.3 t (64,600 lbs)ON OUTRIGGERS FULLY EXTENDED
8.2 m (26'10-7/8") SPREAD
360º ROTATION61.0-m (200.1') + 18.0-m (59.1') Hydraulic offset
jib
20º Tilt 40º Tilt5º Tilt
81.58180797877767573706865636058555350484543403835333028252320G
RC
W R W R
W14.615.017.218.820.321.923.525.028.132.234.838.541.044.546.649.751.554.155.958.259.661.763.064.765.9
4.04.04.04.04.04.04.04.04.03.73.53.33.23.02.92.72.52.22.11.81.71.51.31.00.9
20.020.822.523.825.426.728.229.632.336.238.642.144.447.549.652.554.156.658.060.361.563.164.365.766.6
4.04.04.03.93.83.73.63.63.53.33.23.02.92.72.62.52.32.11.91.71.61.31.20.90.8
24.725.527.028.329.731.032.333.435.939.441.844.746.849.751.554.155.457.558.860.6
3.33.33.23.23.23.13.13.03.02.92.82.82.72.62.52.42.22.01.91.7
57.0-m (187.0') Boom + 18.0-m (59.1') Hydraulic offset jib20º
Tilt 40º Tilt5º Tilt
81.58180797877767573706865636058555350484543403835333028252320G
RC
W R W R
W13.714.516.117.619.220.522.023.426.430.034.636.238.441.643.746.548.451.052.654.956.358.259.661.462.564.065.066.1
4.74.74.74.74.74.74.74.74.64.34.24.03.83.63.43.23.02.72.52.32.21.91.71.41.31.11.00.8
18.819.621.122.423.825.026.327.730.133.736.039.441.344.546.549.550.853.154.556.657.859.560.662.163.164.365.0
4.44.44.34.24.14.03.93.93.73.53.43.33.23.13.13.02.82.52.42.22.01.71.51.31.21.00.9
23.223.925.226.427.728.929.931.233.436.638.741.543.546.248.050.351.853.755.056.8
3.43.43.43.33.33.33.23.23.13.03.02.92.92.82.82.82.72.42.32.1
COUNTERWEIGHT 29.3 t (64,600 lbs)ON OUTRIGGERS FULLY EXTENDED
8.2 m (26'10-7/8") SPREAD
360º ROTATION52.6-m (172.5') Boom + 18.0-m (59.1') Hydraulic
offset jib
20º Tilt 40º Tilt5º Tilt
81.58180797877767573706865636058555350484543403835333028252320G
RC
W R W R W9.29.6
10.711.712.713.614.615.617.420.121.824.426.028.429.932.133.635.637.038.840.041.643.744.245.146.447.248.248.849.6
6.46.46.46.46.46.46.46.46.05.65.35.04.84.64.44.24.13.93.83.73.63.53.43.33.33.23.23.13.13.1
13.614.015.016.016.917.818.619.521.423.825.527.929.431.633.135.136.538.339.641.242.243.644.545.846.547.548.148.8
5.45.35.25.15.04.84.74.64.54.24.13.93.83.63.63.43.43.33.33.23.23.13.13.13.13.13.13.1
17.918.419.320.120.921.722.523.324.927.128.530.632.034.035.337.138.139.740.742.0
3.73.73.63.63.63.53.53.53.43.33.23.23.23.13.13.03.03.03.03.0
35.0-m (114.9') Boom + 18.0-m (59.1') Hydraulic offset jib20º
Tilt 40º Tilt5º Tilt
- 11 -
Jib
C: Loaded boom angle (º)R: Load radius (m)W: Rated lifting
capacity (Unit: x 1,000 kg)G: Number of parts of line
-
- 12 -
GR-1600XL RATED LIFTING CAPACITIES (IN METRIC TON)SPEC. SHEET
NO. GR-1600-3-00104/ES-01
81.581807978777675737068656360585553504845434038353330282523
19.320.322.424.326.328.129.831.434.639.442.246.549.253.255.658.960.863.765.5
3.13.13.13.13.13.02.92.82.62.42.22.01.91.81.71.51.31.10.9
24.325.327.429.130.732.634.135.638.542.945.749.752.256.058.261.363.165.7
2.92.92.92.82.72.72.62.52.32.12.01.91.81.71.61.41.21.0
29.130.031.933.635.136.538.039.542.046.048.552.154.457.759.762.464.166.4
2.62.62.62.62.52.42.32.32.12.01.91.81.71.61.51.31.20.9
C:R:W:G:
Loaded boom angle (º)Load radius (m)Rated lifting capacity
(Unit: x 1,000 kg)Number of parts of line
G 1
RC 5º Tilt
61.0-m (200.1') Boom + 7.0-m (23.0') Insert jib + 18.0-m (59.1')
Hydraulic offset jib20º Tilt 40º Tilt
W R W R
W81.581807978777675737068656360585553504845434038353330282523
17.518.420.322.223.925.727.428.931.936.339.343.245.749.652.055.457.360.061.864.165.7
3.43.43.43.43.43.43.33.23.02.82.72.52.32.22.12.01.81.51.41.11.0
22.323.225.126.928.530.031.532.935.940.042.746.649.152.554.757.859.762.263.565.767.2
3.23.23.23.23.13.02.92.82.72.52.42.32.22.01.91.81.71.51.21.00.8
27.027.929.531.232.534.035.636.839.543.445.849.151.554.556.659.360.762.964.266.2
2.72.72.72.72.62.62.62.52.42.32.22.12.11.91.91.81.61.41.20.9
G 1
RC 5º Tilt
57.0-m (187.0') Boom + 7.0-m (23.0') Insert jib + 18.0-m (59.1')
Hydraulic offset jib20º Tilt 40º Tilt
W R W R W
COUNTERWEIGHT 29.3 t (64,600 lbs)ON OUTRIGGERS FULLY EXTENDED
8.2 m (26'10-7/8") SPREAD
360º ROTATION Insert jib: Option
Insert jib: Option
81.581807978777675737068656360585553504845434038353330282523
15.816.718.520.121.823.425.126.529.433.436.240.242.546.148.451.553.456.157.860.261.663.664.9
3.93.93.93.93.93.93.93.83.63.33.23.02.82.72.62.42.22.01.81.61.41.10.9
20.821.623.424.826.327.829.230.633.337.339.843.445.749.051.354.256.158.460.062.063.265.066.2
3.63.63.63.53.43.33.23.13.02.82.72.52.42.32.32.22.11.81.71.41.20.90.8
25.125.827.428.930.331.632.934.136.640.242.445.747.950.852.855.557.159.360.662.4
2.82.82.82.82.82.72.72.62.52.42.32.22.22.12.12.02.01.81.61.3
G 1
RC 5º Tilt
52.6-m (172.5') Boom + 7.0-m (23.0') Insert jib + 18.0-m (59.1')
Hydraulic offset jib20º Tilt 40º Tilt
W R W R
W81.581807978777675737068656360585553504845434038353330282523
10.110.812.013.114.315.416.417.519.622.624.527.429.232.033.636.237.840.241.643.845.147.048.249.950.952.253.154.254.9
5.45.45.45.45.45.45.35.14.84.34.03.73.53.23.02.82.72.62.52.42.32.22.12.12.02.02.01.91.9
14.715.316.517.618.619.620.621.623.626.528.431.132.835.336.939.240.742.944.246.247.349.050.051.452.353.454.054.9
4.54.54.54.44.24.14.03.83.63.33.23.02.82.72.62.42.42.32.22.12.12.02.01.91.91.91.91.9
19.419.921.022.022.923.824.825.727.430.031.734.035.637.939.341.342.644.445.447.0
3.33.33.33.23.23.13.03.02.82.72.62.52.42.32.22.22.12.12.02.0
G 1
RC 5º Tilt
35.0-m (114.9') Boom + 7.0-m (23.0') Insert jib + 18.0-m (59.1')
Hydraulic offset jib20º Tilt 40º Tilt
W R W R W
COUNTERWEIGHT 29.3 t (64,600 lbs)ON OUTRIGGERS FULLY EXTENDED
8.2 m (26'10-7/8") SPREAD
360º ROTATION
Jib
-
- 13 -
GR-1600XL RATED LIFTING CAPACITIES (IN METRIC TON)SPEC. SHEET
NO. GR-1600-3-00104/ES-01
81.581807978777675737068656360585553504845434038353330282523
21.522.725.027.129.731.433.535.438.944.047.151.954.859.161.565.0
2.12.12.12.12.12.12.12.01.91.71.51.41.31.21.00.8
26.427.529.831.833.835.637.439.042.547.150.254.757.461.463.8
2.12.12.12.12.12.01.91.81.71.51.41.31.21.11.0
32.133.135.036.838.540.041.743.246.250.353.257.159.663.365.3
2.12.12.02.01.91.81.81.71.61.41.31.21.11.10.9
C:R:W:G:
Loaded boom angle (º)Load radius (m)Rated lifting capacity
(Unit: x 1,000 kg)Number of parts of line
G 1
RC 5º Tilt
61.0-m (200.1') Boom + 14.0-m (45.9') Insert jib + 18.0-m
(59.1') Hydraulic offset jib
20º Tilt 40º TiltW R W R W
81.581807978777675737068656360585553504845434038353330282523
19.920.922.924.926.728.630.232.235.540.343.547.950.654.857.260.763.065.8
2.82.82.72.72.62.52.42.42.22.01.91.71.61.51.41.21.10.8
24.525.527.629.531.132.834.636.139.443.846.951.153.757.559.863.265.067.9
2.42.42.42.42.32.22.22.12.01.81.71.61.51.41.31.21.00.8
29.630.632.634.035.837.238.840.243.147.250.053.856.259.861.764.566.268.8
2.22.22.22.12.12.02.01.91.81.71.61.51.41.41.31.11.00.8
G 1
RC 5º Tilt
57.0-m (187.0') Boom + 14.0-m (45.9') Insert jib + 18.0-m
(59.1') Hydraulic offset jib
20º Tilt 40º TiltW R W R W
COUNTERWEIGHT 29.3 t (64,600 lbs) ON OUTRIGGERS FULLY EXTENDED
8.2 m (26'10-7/8") SPREAD
360º ROTATION
81.581807978777675737068656360585553504845434038353330282523
18.019.020.822.624.226.227.829.332.537.140.144.347.050.853.356.958.861.763.666.267.9
3.23.23.13.02.92.92.82.72.52.32.22.01.91.81.71.61.41.21.10.90.8
22.423.425.326.928.430.131.733.236.140.443.247.249.753.455.759.261.263.965.567.9
2.72.72.72.62.52.52.42.32.22.01.91.81.71.61.51.51.41.21.00.9
27.528.230.131.533.134.535.937.340.243.946.650.252.555.957.860.962.664.966.368.6
2.42.42.42.32.32.22.12.12.01.81.81.71.61.51.41.41.31.11.00.9
G 1
RC 5º Tilt
52.6-m (172.5') Boom + 14.0-m (45.9') Insert jib + 18.0-m
(59.1') Hydraulic offset jib
20º Tilt 40º TiltW R W R W
81.581807978777675737068656360585553504845434038353330282523
12.012.814.115.416.617.819.120.122.625.928.131.333.436.438.341.142.945.547.149.551.053.154.356.157.358.859.760.961.6
4.44.44.44.34.24.03.93.73.53.12.92.72.52.32.11.91.81.71.61.51.41.41.31.21.21.11.11.11.0
16.417.118.419.620.822.023.024.226.429.631.734.736.739.341.243.945.648.049.551.653.054.956.057.658.559.860.561.5
3.63.63.63.53.43.33.13.02.92.62.42.22.11.91.81.71.61.51.41.31.31.21.21.21.11.11.11.0
21.221.923.024.125.226.127.228.330.233.135.037.739.542.043.645.947.349.450.752.5
2.92.92.92.82.72.62.52.52.32.12.01.91.81.71.61.51.41.41.31.3
G 1
RC 5º Tilt
35.0-m (114.9') Boom + 14.0-m (45.9') Insert jib + 18.0-m
(59.1') Hydraulic offset jib
20º Tilt 40º TiltW R W R W
COUNTERWEIGHT 64,600 lbs (29.3 t)ON OUTRIGGERS FULLY EXTENDED
26'10-7/8'' (8.20 m) SPREAD
360º ROTATION
Jib
Insert jib: Option
Insert jib: Option
-
- 14 -
GR-1600XL RATED LIFTING CAPACITIES (IN METRIC TON)SPEC. SHEET
NO. GR-1600-3-00104/ES-01
81.581807978777675737068656360585553504845434038353330282520
14.114.816.117.418.519.720.922.024.327.429.532.534.437.239.041.643.245.346.748.749.951.752.854.355.256.6
9.49.29.08.78.48.17.87.57.06.35.95.35.04.54.33.93.73.12.72.32.01.71.51.21.00.8
15.616.217.518.719.820.922.123.225.328.530.433.435.237.939.542.143.545.546.848.850.051.8
9.29.18.88.58.27.97.77.46.96.25.85.34.94.54.23.93.52.92.62.21.91.6
C:R:W:G:
Loaded boom angle (º)Load radius (m)Rated lifting capacity
(Unit: x 1,000 kg)Number of parts of line
G 2
RC 20º Tilt
61.0-m (200.1') Boom + 3.6-m (11.8') Short jib40º Tilt
W R
W81.581807978777675737068656360585553504845434038353330282520
12.713.314.515.516.617.818.819.922.025.026.929.831.634.235.938.339.942.043.345.246.448.149.250.651.652.853.654.656.0
10.810.710.310.09.69.39.08.78.17.46.96.36.05.45.14.74.54.03.63.12.82.42.21.91.71.51.41.21.0
13.614.215.416.417.618.619.620.722.725.727.630.332.234.636.338.640.142.143.445.246.448.1
10.510.310.09.69.39.08.78.47.97.36.86.25.95.45.14.74.53.93.53.02.72.3
G 2
RC 20º Tilt
57.0-m (187.0') Boom + 3.6-m (11.8') Short jib
52.6-m (172.5') Boom + 3.6-m (11.8') Short jib 35.0-m (114.9')
Boom + 3.6-m (11.8') Short jib
40º TiltW R W
COUNTERWEIGHT 29.3 t (64,600 lbs) ON OUTRIGGERS FULLY EXTENDED
8.2 m (26'10-7/8") SPREAD
360º ROTATION
81.581807978777675737068656360585553504845434038353330282520
11.211.812.913.915.016.017.018.019.922.724.427.028.731.132.735.036.538.439.741.542.644.245.246.647.548.749.450.451.7
13.112.912.412.011.611.210.710.39.68.68.07.36.96.36.05.65.34.74.33.83.43.02.72.42.21.91.81.61.4
12.112.713.814.815.816.817.818.720.623.324.827.629.231.633.135.336.738.639.841.542.644.2
12.612.411.911.511.110.810.410.09.38.47.97.26.86.35.95.55.24.64.23.63.32.9
G 2
RC 20º Tilt 40º Tilt
W R
W81.581807978777675737068656360585553504845434038353330282520
6.56.87.58.28.99.5
10.210.812.114.015.317.118.319.921.022.523.524.925.827.127.929.029.830.831.432.332.933.634.6
22.222.021.721.321.020.720.420.119.618.918.518.017.716.916.315.214.112.611.810.810.29.48.98.38.07.67.37.06.5
6.97.27.98.69.29.9
10.511.212.514.315.617.418.620.221.322.923.825.126.027.228.029.2
18.017.917.717.517.417.217.116.916.716.316.215.915.815.615.514.913.812.511.710.710.19.3
G 4
RC 20º Tilt 40º Tilt
W R W
COUNTERWEIGHT 29.3 t (64,600 lbs) ON OUTRIGGERS FULLY EXTENDED
8.2 m (26'10-7/8") SPREAD
360º ROTATION
Jib
Short jib: Option
Short jib: Option
-
Overfront
360˚ OverRear
Approx.10˚
Approx.10˚
WARNING AND OPERATING INSTRUCTIONSFOR ON RUBBER LIFTING
CAPACITIES
1. Rated lifting capacities on-rubber do not exceed 75% of
tipping loads as determined by SAE J765-Crane Stability Test
Code.
2. On rubber lifting is only permitted without couterweight and
stationary. Creep operation is prohibited.Rated lifting capacities
shown in the chart are based on the condition that crane is set on
�rm level surfaces with suspension lock applied. Those above thick
lines are based on tire capacity and those below, on crane
stability. They are based on actual load radius increased by tire
deformation and boom de�ection.
3. If the suspension lock cylinders contain air, the axle will
not be locked completely and rated lifting capacities may not be
obtainable. Bleed the cylinders according to the operation safety
and maintenance manual.
4. Rated lifting capacities are based on proper tire in�ation,
capacity and condition. Damaged tires are hazardous to safe
operation of crane.
5. Tires shall be in�ated to correct air pressure.
6. Over front operation shall be performed within 10 degrees in
front of chassis.
7. On rubber lifting with "jib" is not permitted. Maximum
permissible boom length is 21.8 m (71.6').
8. When making lift on rubber stationary, set parking brake.9.
The mass of the hook (1,080 kg (2,381 lbs) for 100 metric ton
(110 ton) capacity, 300 kg (661 lbs) for 7.2 metric ton (7.9
ton) capacity), slings and all similarly used load handling devices
must be considered as part of the load and must be deducted from
the lifting capacities.
10. For rated lifting capacity of single top, reduce the rated
lifting capacities of relevant boom according to a weight
reductions for auxiliary load handling equipment. Capacities of
single top shall not exceed 7,200 kg (15,900 lbs) including main
hook.
11. The lifting capacity data stowed in the LOAD MOMENT
INDICATOR (AML-C) is based on the standard number of parts of line
listed in the chart. Standard number of parts of line for on rubber
operation should be according to the following table.
Tires26.5R25☆☆☆
Air Pressure650 kPa (94 psi)
GR-1600XL RATED LIFTING CAPACITIES (IN METRIC TON)
WITHOUT COUNTERWEIGHT ON-RUBBER STATIONARYA
B
2.503.003.504.004.505.005.506.006.507.007.508.009.00
10.0011.0012.00
73716866636158555249464335
000004
0000454
0000
904
000004
0000
454
0000904
10.010.010.010.010.09.28.06.95.95.14.33.31.8
10.010.010.010.010.010.09.58.47.46.55.85.13.72.41.5
10.010.010.010.010.010.010.09.18.17.46.65.94.63.42.41.7
A: Boom length (m)B: Load radius (m)C: Loaded boom angle (º)D:
Minimum boom angle (º)
for indicated length (no load)E: Number of parts of line
Telescoping conditions (%)
C (42.8')13.1 m
Over front and rear 360º Rotation
17.4 m 21.8 m
0 40 50 47 56 59
(57.2') (42.8')13.1 m 17.4 m 21.8 m
(57.2')(71.6')787674727169676563615957534944
D
Tele. 1Tele. 2Tele. 3Tele. 4Tele. 5
E
C80797876757472716968676562595652
737168666361585552
10.010.09.98.06.45.14.03.02.1
10.010.010.09.78.16.85.74.73.93.12.41.7
10.010.010.010.0
9.07.76.65.64.84.13.32.71.7
(71.6')787674727169676563615957
80797876757472716968676562
C C C C
Boom length13.1 m (42.8') to 21.8 m (71.6')
Number of parts of line4
NOTE: The lifting capacity data stowed in the LOAD MOMENT
INDICATOR (AML-C) is based on the standard number of parts of line
listed in the chart.Standard number of parts of line for on-rubber
operation should be according to the chart.
-15-
SPEC. SHEET NO. GR-1600-3-00104/ES-01
-
WARNING AND OPERATING INSTRUCTIONSFOR LIFTING CAPACITIES
GENERALRATED LIFTING CAPACITIES apply only to the machine as
originally manufactured and normally equipped by TADANO LTD.
Modi�cations to the machine or use of optional equipment other than
that speci�ed can result in a reduction of capacity.Hydraulic
cranes can be hazardous if improperly operated or maintained.
Operation and maintenance of this machine must be in compliance
with information in the Operation and Maintenance Manual supplied
with the crane. If this manual is missing, order a replacement
through the distributor.The operator and other personnel associated
with this machine shall fully acquaint themselves with the latest
applicable ASME B30.5 safety standards for cranes as mentioned in
OSHA CFR29 part 1926.
SET UPRated lifting capacities on the load chart are the maximum
allowable crane capacities, are based on the machine standing level
on �rm supporting surface under ideal job conditions. Depending on
the nature of the supporting surface, it may be necessary to have
structural supports under the outrigger �oats or tires to spread
the loads to a larger surface.For outrigger operation, outriggers
shall be properly extended with tires free of supporting surface
before operating crane.
OPERATIONRated lifting capacities have been tested to and meet
minimum requirements of SAE J1063-Cantilevered Boom Crane
Structures Method of Test.Rated lifting capacities do not exceed
85% of the tipping load on outriggers fully extended as determined
by SAE J765-Crane Stability Test Code.Rated lifting capacities for
partially extended outriggers are determined from the formula,
Rated Lifting Capacities=(Tipping Load - 0.1 x Tip
Reaction)/1.25.Rated lifting capacities above thick lines in the
chart are based on crane strength and those below, on its
stability. They are based on actual load radius increased by boom
de�ection.The weight of handling device such as hook blocks,
slings, etc., must be considered as part of the load and must be
deducted from the lifting capacities.Rated lifting capacities are
based on freely suspended loads and make no allowance for such
factors as the effect of wind, sudden stopping of loads, supporting
surface conditions, in�ation of tires, operating speeds, side
loads, etc. Side pull on the boom or jib is extremely
dangerous.Such action can damage the boom, jib or slewing
mechanism, and lead to overturning the crane.Rated lifting
capacities do not account for wind on lifted load or boom. We
recommend against working under the conditions that the load is out
of control due to a strong wind.During boom lift, consider that the
rated lifting capacity is reduced by 50% when the wind speed is 9
m/s (20 mph) to 12 m/s (27 mph); reduced by 70% when the wind speed
is 12 m/s (27 mph) to 14 m/s (31 mph). If the wind speed is 14 m/s
(31 mph) or over, stop operation. During jib lift, stop operation
if the wind speed is 9 m/s (20 mph) or over.
Rated lifting capacities at load radius shall not be exceeded.
Do not tip the crane to determine allowable loads.Do not operate at
boom lengths, radii, or boom angle, where no capacities are shown.
Crane may overturn without any load on the hook.When boom length is
between values listed, refer to the rated lifting capacities of the
next longer and next shorter booms for the same radius. The lesser
of the two rated lifting capacities shall be used.When making lifts
at a load radius not shown, use the next longer radius to determine
allowable capacity.Load per line should not exceed 7,200 kg (15,900
lbs) for main winch and auxiliary winch.Check the actual number of
parts of line with LOAD MOMENT INDICATOR (AML-C) before operation.
Maximum lifting capacity is restricted by the number of parts of
line of LOAD MOMENT INDICATOR (AML-C). Limited capacity is as
determined from the formula, Single line pull for main winch 7,200
kg (15,900 lbs) x number of parts of line.The boom angle before
loading should be greater to account for de�ection. For rated
lifting capacities, the loaded boom angle and the load radius is
for reference only.Do not operate extension or retraction of the
boom with loads.For lifting capacity of single top, deduct the
weight of the load handling equipment from the rated lifting
capacity of the boom.For the lifting capacity of single top, the
net capacity shall not exceed 7,200 kg (15,900 lbs) including main
boom hook mass attached to the boom.When the base jib or top jib or
both jibs are removed, set the jib state switch to the REMOVED
position.When erecting and stowing jib, be sure to retain it by
hand or by other means to prevent its free movement.Use
"ANTI-TWO-BLOCK DEVICE" disable switch when erecting and stowing
jib and when stowing hook block. While the switch is pushed, the
winch does not stop, even when overwind condition occurs.For
selected boom length or less with jib, rated lifting capacities are
determined by loaded boom angle only in the column headed "selected
boom + jib".Outriggers shall be extended 8.2 m (26' 10-7/8") spread
when installing or removing removable counterweight.
DEFINITIONSLoad Radius: Horizontal distance from a projection of
the axis of rotation to supporting surface before loading to the
center of the vertical winch line or tackle with load
applied.Loaded Boom Angle: The angle between the boom base section
and the horizontal, after lifting the rated lifting capacity at the
load radius.Working Area: Area measured in a circular arc about the
centerline of rotation.Freely Suspended Load: Load hanging free
with no direct external force applied except by the winch line.Side
Load: Horizontal side force applied to the lifted load either on
the ground or in the air.
1.
2.
3.
1.
2.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.15.
16.
17.
18.
19.
20.
1.
2.
3.
4.
5.
-16-
SPEC. SHEET NO. GR-1600-3-00104/ES-01
-
WARNING AND OPERATING INSTRUCTIONS FOR USING THE LOAD MOMENT
INDICATOR (AML-C)
GR-1600XL Axle weight distribution chart
GVW
Kilograms
1st 2nd
Basic machine
Hydrauric offset jib
Remove: 1. 7.2 metric ton (7.9 ton) hook block2. 100 metric ton
(110 ton) hook block3. Counterweight 11,100 kg (24,500 lbs)4.
Counterweight 18,200 kg (40,100 lbs)5. Front and rear outrigger
boxes and beams 6. Auxiliary Winch & wire rope7. Boom and
Jib
-300-1,080
-11,120-18,160-8,962-1,202
-17,424
-421-1,7713,3515,473
-3,463490
-22,543
61346
-7,236-11,816-2,750
-8462,559
91,154 29,398 30,640
3nd
61346
-7,236-11,816-2,750
-8462,559
31,116
GVW
Pounds
1st 2nd
-661-2,381
-24,515-40,036-19,758-2,650
-38,413
-928-3,9047,388
12,066-7,6351,080
-49,699
134763
-15,953-26,050-6,063-1,8655,642
200,960 64,812 67,550
3nd
134763
-15,953-26,050-6,063-1,8655,642
68,599
Set AML select keys in accordance with the actually operating
crane conditions and don't fail to make sure, before crane
operation, that the displays on front panel are correct.When
operating crane on outriggers:
• Set P.T.O. switch to "ON".• Press the outrigger state select
key to register for the
outrigger operation. If the display agrees with the actual
state, press the set key to register. After the completion of the
registration, the pop-up window closes.
• Press the lift state select key to register the lift state to
be used (single top / jib / boom).
• Each time the lift state select key is pressed, the display
changes. If the display agrees with the autual state, press the set
key to register. After the completion of the registration, the
pop-up window closes.
• When erecting and stowing jib, select the status of jib set
(Jib lift indicator symbol �ickers).
When operating crane on rubber:• Set P.T.O. switch to "ON".•
Press the outrigger state select key to register for the on
rubber operation. Each time the outrigger state select key is
pressed, the display changes. Select the stationary operation, the
on rubber state indicative symbol �ickers.
• Press the lift state select key to register the lift
state.However, pay attention to the following.For stationary
operation.
• The front and rear capacities are attainable only when the
over front or rear position. The front capacities are attainable
only when the over front position symbol comes on. When the boom is
more than 2 degrees from centered over front of chassis, 360º
capacities are in effect.
• When a load is lifted in the front or rear position and then
swung to the side area, make sure the value of the LOAD
MOMENT INDICATOR (AML-C) is below the 360º lifting capacity.This
machine is equipped with an automatic slewing stop device. (For the
details, see Operation and Maintenance Manual.) But, operate very
carefully because the automatic slewing stop does not work in the
following case.
• During on-rubber operation.• When the "P.T.O" switch is set to
"OVERRIDE" and the
"OVERRIDE" key switch outside the cab is on.During crane
operation, make sure that the displays on front panel are in
accordance with actual operating conditions.The displayed values of
LOAD MOMENT INDICATOR (AML-C) are based on freely suspended loads
and make no allowance for such factors as the effect of wind,
sudden stopping of loads, supporting surface conditions, in�ation
of tire, operating speed, side loads, etc.For safe operation, it is
recommended when extending and lowering boom or slewing, lifting
loads shall be appropriately reduced.LOAD MOMENT INDICATOR (AML-C)
is intended as an aid to the operator. Under no condition should it
be relied upon to replace use of capacity charts and operating
instruction. Sole reliance upon LOAD MOMENT INDICATOR (AML-C) aids
in place of good operating practice can cause an accident. The
operator must exercise caution to assure safety.
1.
2.
3.
4.
5.
6.
7.
SPEC. SHEET NO. GR-1600-3-00104/ES-01
-17-
-
MEMO
-
MEMO
-
4-12, Kamezawa 2-chome,Sumida-ku, Tokyo 130-0014, Japan
Tel : +81-(0)3-3621-7750Fax: +81-(0)3-3621-7785
http://www.tadano.com/[email protected] Printed in Japan
2016-5-1E-mail
URL
(International Sales Division)