1 1 GO RHINO! PRODUCTS 3000 SERIES INSTALLATION INSTRUCTIONS 03-06 FORD EXPEDITION 2/4WD PART NO. 3285 B-C REV.B 6/09 QTY PARTS DESCRIPTION 1 P200 PLUG KIT 6 ¼” X ¾” BUTTON HEAD BOLTS 6 ¼” LOCK WASHERS 6 ¼” FLAT WASHERS 6 ¼” HEX NUTS 4 5/16” X 1” HEX BOLTS 4 5/16” LOCK WASHERS 4 5/16” HEX NUTS 6 3/8” X 1” BUTTON HEAD BOLTS 6 3/8” X 1” HEX BOLTS 6 3/8” LOCK WASHERS 6 3/8” HEX NUTS QTY PARTS DESCRIPTION 4 ½” X 1 ½” HEX BOLTS 4 ½” FLAT WASHERS 4 ½” LOCK WASHERS 4 ½” HEX NUTS 2 1122LP LICENSE PLATE BRACKETS 1 1122AD DRIVER SIDE UPPER BRACKET 1 1122AP PASSENGER SIDE UPPER BRACKET 1 1122BD DRIVER SIDE LOWER BRACKET 1 1122BP PASSENGER SIDE LOWER BRACKET 5 1/4" PLASTIC PIN GRIPS ASSEMBLY INSTRUCTIONS STEP 1. BEGIN THE ASSEMBLY BY LOOSELY ATTACHING THE BOTTOM STEP TUBE TO THE GRILLE GUARD SIDE PLATES USING THE 3/8” X 1” BUTTON HEAD BOLTS. STEP 2. INSTALL THE TUBE CONNECTORS FROM THE P200 PLUG KIT INTO THE TOP TUBE. STEP 3. POSITION THE CENTER PLATE BETWEEN THE GRILLE GUARD SIDE PLATES. ATTACH USING THE 3/8" HEX HEAD BOLTS SUPPLIED. STEP 4. ALIGN THE GRILLE AND TIGHTEN ALL NUTS AND BOLTS. INSTALLATION INSTRUCTIONS STEP 1. REMOVE THE LICENSE PLATE AND MOUNTING BRACKET FROM THE FRONT BUMPER. STEP 2. BEGINNING WITH THE DRIVER SIDE, LOCATE AND REMOVE THE TWO HEX NUTS FROM THE BOLT ASSEMBLY THAT SECURE THE BUMPER TO THE FRAME FLANGE. NOTE: REMOVE THE (3) PLASTIC RIVETS AND PULL BACK THE RUBBER SPLASH GUARD TO EASE THE INSTALLATION.
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
1
1
GO RHINO! PRODUCTS 3000 SERIES INSTALLATION INSTRUCTIONS03-06 FORD EXPEDITION 2/4WD PART NO. 3285 B-C REV.B 6/09
QTY PARTS DESCRIPTION1 P200 PLUG KIT6 ¼” X ¾” BUTTON HEAD BOLTS6 ¼” LOCK WASHERS6 ¼” FLAT WASHERS6 ¼” HEX NUTS4 5/16” X 1” HEX BOLTS4 5/16” LOCK WASHERS4 5/16” HEX NUTS6 3/8” X 1” BUTTON HEAD BOLTS6 3/8” X 1” HEX BOLTS6 3/8” LOCK WASHERS6 3/8” HEX NUTS
QTY PARTS DESCRIPTION4 ½” X 1 ½” HEX BOLTS4 ½” FLAT WASHERS4 ½” LOCK WASHERS4 ½” HEX NUTS2 1122LP LICENSE PLATE BRACKETS1 1122AD DRIVER SIDE UPPER BRACKET1 1122AP PASSENGER SIDE UPPER BRACKET1 1122BD DRIVER SIDE LOWER BRACKET1 1122BP PASSENGER SIDE LOWER BRACKET5 1/4" PLASTIC PIN GRIPS
ASSEMBLY INSTRUCTIONSSTEP 1. BEGIN THE ASSEMBLY BY LOOSELYATTACHING THE BOTTOM STEP TUBE TO THE GRILLEGUARD SIDE PLATES USING THE 3/8” X 1” BUTTONHEAD BOLTS.
STEP 2. INSTALL THE TUBE CONNECTORS FROM THE P200 PLUG KIT INTO THE TOP TUBE.
STEP 3. POSITION THE CENTER PLATE BETWEEN THEGRILLE GUARD SIDE PLATES. ATTACH USING THE 3/8"
HEX HEAD BOLTS SUPPLIED.
STEP 4. ALIGN THE GRILLE AND TIGHTEN ALL NUTSAND BOLTS.
INSTALLATION INSTRUCTIONS
STEP 1. REMOVE THE LICENSE PLATE AND MOUNTING BRACKET FROM THE FRONT BUMPER.
STEP 2. BEGINNING WITH THE DRIVER SIDE, LOCATEAND REMOVE THE TWO HEX NUTS FROM THE BOLTASSEMBLY THAT SECURE THE BUMPER TO THEFRAME FLANGE.
NOTE: REMOVE THE (3) PLASTIC RIVETS AND PULL BACK THE RUBBER SPLASH GUARD TO EASE THE INSTALLATION.
2
2
STEP 3. POSITION 1122BD LOWER BRACKET OVERTHE BOLTS, AND ATTACH IT TO THE FRAME FLANGEUSING THE FACTORY NUTS. (FINGER TIGHTEN ONLY).
STEP 4. INSERT 1122AD UPPER BRACKET THROUGHTHE OPENING IN THE GRILLE, AND ATTACH IT TO1122BD LOWER BRACKET USING THE 5/16” HEX HEADBOLTS. (FINGER TIGHTEN ONLY).
STEP 5. REPEAT THE ABOVE STEPS FOR THE PASSENGER SIDE BRACKETS.
STEP 6. ATTACH THE GRILLE GUARD ASSEMBLY TOTHE LOWER BRACKETS USING THE ½” FASTENERS.
3
STEP 7. ATTACH THE GRILLE GUARD ASSEMBLY TOTHE UPPER BRACKETS USING THE 3/8” FASTENERS.
STEP 8. ALIGN THE GRILLE GUARD ASSEMBLY WITH THE FRONT OF THE VEHICLE AND TIGHTEN ALL MOUNTINGNUTS AND BOLTS.
STEP 9. ATTACH 1122LP LICENSE PLATE BRACKETSAND THE LICENSE PLATE TO THE BOTTOM SIDE OFTHE GRILLE GUARD CENTER PLATE, USING THE ¼”FASTENERS.
STEP 10. RE-ATTACH THE RUBBER SPLASH GUARD USING THE PLASTIC RIVETS SUPPLIED.
Related Documents
