GENERAL MOTORS 4L60E/65E/70E · GENERAL MOTORS Pump Cover 4L60E/65E/70E Pump cover kits: 1998-2005: 12491417, 12491421 2006 and later Non PHT: 24236486, 24236489 2006/07 PHT: 24239202
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
GENERAL MOTORSGENERAL MOTORSGENERAL MOTORSGENERAL MOTORSGENERAL MOTORS42
The 2005 and 2006 ATRA seminars covered the changes involved with the addi-tion of the input speed sensor in the 4L60E/65E and 4L70E applications (RPO’sM30,M32, M33, M70). The input speed sensor was not used on all 2006-2007applications so some confusion may occur regarding build combinations for theseproducts. Some of the parts from the ISS equipped applications and a Non ISSequipped applications cannot be intermixed.
A failure to identify the build combination you are working with may result in linepressure, TCC and/or Clutch apply/release/cross leak concerns. Five designvariations have occurred between Non ISS applications and the final fully func-tional ISS applications. These changes include the following:
• Redesigns of the turbine shaft—Repositioning of the seal rings on the shaft,adding a ISS toothed wheel.
• Redesign of the pump cover- Updating the passage design and passageposition in the stator support sleeve. Adding a boss to the cover for the ISS.
• Shortening the P/R valve train to make room for the input speed sensorwiring and connector.
• Updating the wiring harness for the input speed sensor.
GENERAL MOTORSGENERAL MOTORSGENERAL MOTORSGENERAL MOTORSGENERAL MOTORS
4L60E/65E/70EInput Speed Sensor
Design Variation Turbine Shaft:
Four NON ISS shaft sizes are available they are:245mm/258mm shaft (Part # 17803688)280mm/300mm shaft (Part # 17803687)300mm HD/300mm M70 ( Part #17803686)258mm PHT (Part # 17803685)
Three ISS equipped shafts are available, they are:245mm/258mm (Part #24232438)280mm/300mm (Part # 24230653)300mm HD/M70 (Part #24230654)
(continued)
GENERAL MOTORSGENERAL MOTORSGENERAL MOTORSGENERAL MOTORSGENERAL MOTORS44
The design of the shaft can be identified by the ID marks on the shaft. The IDmark is simply a 9.5mmX.5mm groove that located on the shaft. Some shaftshave ID marks while others do not.
Pump Cover: 5 pump covers are available, they are:
1997-2005 model: No input sensor boss, used 1st design stator support bushingand 1st design P/R valve train.
GENERAL MOTORSGENERAL MOTORSGENERAL MOTORSGENERAL MOTORSGENERAL MOTORS
Pump Cover
4L60E/65E/70E
Pump cover kits:1998-2005: 12491417, 124914212006 and later Non PHT: 24236486, 242364892006/07 PHT: 24239202
Reverse boost valve kits:2005 and earlier (Long valve train): 24234396 regular, 24234397 High PerfShort valve train 24234396 regular, 24234397 High Perf
2006: The input speed sensor boss was drilled on those models that used an ISS.A 2nd design stator support sleeve and a 2nd design P/R valve train were used.This combination requires the ISS shaft design or a shaft design that relocatesthe turbine seal ring position.
2006 and later: All models of pumps use the input speed sensor boss and all ofthe bosses are drilled. If the ISS is not used a rubber plug will be used in the ISShole. A 2nd design stator support sleeve and a 2nd design P/R valve train wereused. This combination requires the ISS shaft design or a shaft design that relo-cates the turbine seal ring position.
(continued)
GENERAL MOTORSGENERAL MOTORSGENERAL MOTORSGENERAL MOTORSGENERAL MOTORS48