This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Driver Installation ………………………….………………… Install at WinXP/2000 ….………………………………………..
Capture Board Install ………………………………………………
Overlay Board Install ………….……………………………………
Driver Creation Check ….………..……………………………. Display and other Setting ……….………………………………
Software Installation …………………………..………….. DVR Program Setup………………………………………….…...
Setting……………………………………………….…………………
File System Setup…………………………….……………… DVR Main Running …………………………………………………….
CONTENTS
1
2
2-1
2.1.1
2.1.2
2.2
2.2.1
2.2.2
3
3.1
3.1.1
3.1.2
3.1.3
3.2
3.2.1
3.2.2
4
4.1
4.1.1
4.1.2
4.3
4.4
5
5.1
5.1.1
6
7
- Pan/Tilt Camera ‘ Protocol install value by each camera- Capture Card &Receiver connecting methods - Sensors & Relays Connector Pin Spec(KIT) - Back I/O B’d with Sensors & Relays(SET)
Appendix
Winnertec Systems Co.,LTD 3
GOLDENEYE INSTALL GUIDE MANUAL
GED5500 is GOLDENEYE series of Winnertec system. Thanks for choosing our products. All copyright belongs to Winnertec system. Please make sure to read this manual because this is explanation of systemprogram setting and Pan/Tilt control and the way of other equipment
1. Please power off before installation.
2. Please make an enough room to connect.
3. Please do not install this around magnetic material, all heating system.
(Adaptable temperature is 5 ~35℃ ℃)
4. Please install this to where be stable and flat.
5. Please do not put heavy thing on the monitor.
6. Please do not separate this intentionally. If you need to uncover this unit, please
contact the retailed seller or WINNERTEC and get help some tips.
. In case that you might break down this with using unrecorded components, we are not
responsible for any incident from this.
Products
Caution
Check the Components
Please check these items when you purchase it first and contact the shop where you
bought this in case you could not find as listed. (Option: Monitor, Audio Input Cable)
- In case of KIT
Related Cable(video, camera, sensor, other)
- In case of SET
1. Main DVR(Ged5000) 2. Mouse 3. KeyBoard
4. Key 5. User Manual 6. Power Cable
7. CD (Software, other system CD)
Winnertec Systems Co.,LTD 4
GOLDENEYE INSTALL GUIDE MANUAL
H/W Requirements CPU Pentium4 – 2.4G Memory 512MB over Main Board Intel Chip Set compatible Hard Disk Drive 120G
Video Card Resolution: 1024X768 Color : True Color(32bit) over Memory 32MB
▣ Check the item list【 Set Base VS Kit Base 】
Set Base Kit Base DVR 1 Set 1pc of User manual 1pc of Program Software CD 1pc of Capture Board BNC Board 1ea(built in already) 1pc of Overlay Board Cable 1 Set (built in already) - 2pc of Sensor cable(16sensor
basis) - 1pc of output relay - 2pcs of video capture input cable - 1pc of Live Video cable - 1pc of Video out cable
- 1pc of Program Software CD - 1pc of Capture Board - 1pc of Overlay Board - Cable 1 Set
-1pc of Video capture input cable -1pc of Live Video Cable -1pc of sensor cable
Following is the procedure of installation of one system※
1. Confirm of the item list board, channel number, cable, other)
2. Products assembly (CPU, RAM, VGA Card, connecting to main board)
3. O/S (Operating System) installation
4. If necessary, Patch (Bios, Main Board Patch upgrade), service pack patch.
After power on, automatically plug& play, Capture Board or Overlay Board will be installed. Each Board is composed of Audio / Video Capture Section
Driver install procedure ※ -Drivers capture
Overlay
4.1.1 Capture Board Install
4.1 Install at WinXP/2000
Location: In the driver folder provided CD driver in which capture
folder & overlay folder.
Select ‘specify a location’ and click ‘browse’
4 Driver Installation
Winnertec Systems Co.,LTD 14
GOLDENEYE INSTALL GUIDE MANUAL
Select ‘specify a location’ and click ‘browse’
4.1.2 Overlay Board Install
Installation is the same as Capture Board (1-3) and designates the exact location at 4.
Cilck ‘Finished’
※ The other is the same as before
Winnertec Systems Co.,LTD 15
GOLDENEYE INSTALL GUIDE MANUAL
1. Checking at WinXP/2000
4.3 Driver creation check
Capture Board
Overlay Board
Winnertec Systems Co.,LTD 16
GOLDENEYE INSTALL GUIDE MANUAL
If you cannot make suitable adjustment, you might have wrong display.
Screen Saver is not used. (None status) and leave the power scheme and system
standby “never” as shown,
You can also turn off the power for save the electricity, but you need to mark as above on ※
the display setting.
.
4.4 Display and other Setting
※ Recommendable
Resolution: 1024*768,
Color: True color (32bit)
Winnertec Systems Co.,LTD 17
GOLDENEYE INSTALL GUIDE MANUAL
Double click setup button, program will be set.. ※
5 Software installation
If you already have this software,click “no” if you do not, click‘Yes’
Before Directx 8.0 after Directx 8.0,You also find left picture. Click “yes” and reboot it. Please click “ok” when you havewarning window such as “file systemcan not be found”.
Winnertec Systems Co.,LTD 18
GOLDENEYE INSTALL GUIDE MANUAL
After software program installation, you have to do Setting / File system Setup
You have to choose mode type.
In case that you reboot after DVR program already registered at start program,
You may see the right picture you can choose video mode.
If you mistakenly chose the wrong one, you can open Windows. Winnt folder, –
Ged4000.ini file
You also change NTSCORPAL part Values (1 or 2).
You also close the window after clicking “ok” even though there will be warning message
Such as “file system can not be found”. This is not error message, so you can keep going on.
5.1.1 Setting You can find below log-in window after Setting (start-program-DVR-Setting or
Main basic screen DVR Setup, double click).
5.1 DVR Program Setup
Input “test” as a password and
User name, then you will have
following wind.
⇒ ⑴ General setting
⇒ ⑵ Camera setting
⇒ ⑶ Motion & display setting
⇒ ⑷ Network setting
⇒ ⑸ sensor setting
⇒ ⑹ User setting
⇒ ⑺ Saving & exit
⇒ ⑻ Not saving & exit
⑵click the camera no.which you need to use check” use” (color willbe turning to red) click ‘ok’ and exit ⑺saveand finished. Please refer to user’smanual if you more.
test
test
[SYSTEM]
NTSCORPAL=1 ' 1 - NTSC, 2 - PAL
Winnertec Systems Co.,LTD 19
GOLDENEYE INSTALL GUIDE MANUAL
You have do “File System Setting” first.
This is for making the enough room. Exe is as follows;
‘Start-program-DVR-DVR File System’ or c:/program files/goldeneye/ FSutil.exe .
If you find following window, insert the number of Basket on the D,E(added HDD included)⑴
and click “ok”.
⑵ Input the number of basket at each drive.
⑶ Start (‘③’) button to make Basket
⑶ Click the “Exit” to get out.
6 File System Setup
①
③
844
■ Note for Basket making
Please do not make basket on the C drive.
This is for data distinguishing. The input basket number should be less than
maximum
Value by one.
For example, if ‘845’ is the maximum number, please input ‘844’.
Winnertec Systems Co.,LTD 20
GOLDENEYE INSTALL GUIDE MANUAL
■ ADD BASKET TO USE
If you want to add HDD or have more Basket to add, you can run file system and choose
The basket you want to use. Refer to the following
⑴ File System program runs
⑵ Click the HDD to add or click left drive.
⑶ Insert Basket values.
⑷ After finishing inputting , put the “start” button and make a basket.
⑸ After Basket is made, click the “finished” button..
■ Basket Rebuild If you want to erase all recorded data at HDD, follows 1,2,3.
⑴ please get rid of OWLFS folder or format D,E(drive which has drive).
⑵ Get rid of Gedfs.ifs File at C drive toot.
⑶ Run the DVR File System to make Basket.
Setting / File System is only the preparing job for DVR Main function,
You can see the initial screen when you turn on power. Program will be running automatically
on PC and begins to record.
Double click DVR main on the main screen, or RUN start->program->DVR->DVR Main.
Program running order is registered on the computer, please turn off the computer and turn it