To prevent possible SERIOUS INJURY or DEATH from a moving gate or door: • ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters. • Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel. • ALWAYS keep gate or door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. Universal Mini Remote Control Read instructions thoroughly BEFORE beginning. If using the Universal Mini Remote Control with residential door openers, the remote control must be used only with door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are always located on or near the bottom of the door track. STOP MODEL 374UT TABLE OF CONTENTS GETTING STARTED .................................................... 2 LOCATE THE PROGRAM/LEARN BUTTON ........................ 3-7 Chamberlain ® products ............................................. 3 Genie ® products ..................................................... 4 Linear ® products ..................................................... 5 Wayne Dalton ® products ........................................... 5 LiftMaster ® products ................................................ 6 Overhead Door ® products .......................................... 6 Stanley ® products ................................................... 7 GARAGE DOOR OPENERS .......................................... 8-9 Programming to a garage door opener with a Program/LEARN button ............................................. 8 Programming to a Genie ® Intellicode ® 2 garage door opener ................................................. 9 Programming to a LiftMaster garage door opener using the LEARN button on the control panel ......................... 10 COMMERCIAL DOOR OPERATORS ................................. 11 Programming to a commercial door operator with a RADIO button................................................ 11 GATE OPERATORS .................................................... 12 Program to a gate operator with a Program/LEARN button .................................... 12 EXTERNAL RECEIVERS ............................................... 13 Programming to an external receiver with a Program/LEARN button .................................... 13 MYQ ® LIGHT CONTROLS ............................................ 14 Programming to a MyQ ® Light Control .......................... 14 NEED HELP? ........................................................... 15 BATTERY ............................................................... 16
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
To prevent possible SERIOUS INJURY or DEATH from a moving gate or door:• ALWAYSkeepremotecontrolsoutofreachofchildren.NEVERpermitchildrentooperate,orplaywithremotecontrol
transmitters.• ActivategateordoorONLYwhenitcanbeseenclearly,isproperlyadjustedandtherearenoobstructionstodoortravel.• ALWAYSkeepgateordoorinsightuntilcompletelyclosed.NEVERpermitanyonetocrosspathofmovinggateordoor.
Universal Mini Remote Control
Read instructions thoroughly BEFORE beginning.
If using the Universal Mini Remote Control with residential door openers, the remote control must be used only with door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are always located on or near the bottom of the door track.
STOP
MODEL 374UT
TaBLE OF COnTEnTSGeTTInG STaRTed .................................................... 2
LOCaTe THe PROGRaM/LeaRn BUTTOn ........................ 3-7Chamberlain® products ............................................. 3Genie® products ..................................................... 4Linear® products ..................................................... 5Wayne dalton® products ........................................... 5LiftMaster® products ................................................ 6Overhead door® products .......................................... 6Stanley® products ................................................... 7
GaRaGe dOOR OPeneRS .......................................... 8-9Programming to a garage door opener with a Program/LeaRn button ............................................. 8Programming to a Genie® Intellicode® 2 garage door opener ................................................. 9Programming to a LiftMaster garage door opener using the LeaRn button on the control panel ......................... 10
COMMeRCIaL dOOR OPeRaTORS ................................. 11Programming to a commercial door operator with a RadIO button................................................ 11
GaTe OPeRaTORS .................................................... 12Program to a gate operator with a Program/LeaRn button .................................... 12
exTeRnaL ReCeIveRS ............................................... 13Programming to an external receiver with a Program/LeaRn button .................................... 13
MyQ® LIGHT COnTROLS ............................................ 14Programming to a MyQ® Light Control .......................... 14
need HeLP? ........................................................... 15
BaTTeRy ............................................................... 16
2
gETTing STaRTED
The Universal Mini Remote Control can be programmed to activate up to two products, such as a garage door opener, MyQ® light control, gate operator, or commercial door operator. each button on the remote control works independently of the other and must be programmed separately. The images throughout this manual are for reference only and your product may look different.
Bottom Button
Garage door Opener Commercial door OperatorGate Operator
Led
you will need to locate the Program/LeaRn button on your product before you start programming.
GaRaGe dOOR OPeneRS
TheProgram/LEARNbuttonistypicallylocatedonthebackorsidepanelofyourgaragedooropener.YourProgram/LEARNbuttonmayhaveadifferentname(SMARTbutton,SETbutton,etc.).ForhelplocatingyourProgram/LEARNbuttonrefertotheTableofContentsinthismanualorcontactyourgaragedooropenermanufacturer.
COMMeRCIaL dOOR OPeRaTORS
TheRADIObuttonistypicallylocatedonthelogicboardofyouroperator.ForhelplocatingyourRADIObuttoncontactyourdooroperatormanufacturer.
GaTe OPeRaTORS
TheProgram/LEARNbuttonistypicallylocatedonthecontrolboardofyouroperator.YourProgram/LEARNbuttonmayhaveadifferentname(RADIObutton,XMITTERbutton,etc.).ForhelplocatingyourProgram/LEARNbuttoncontactyourgateoperatormanufacturer.
exTeRnaL ReCeIveR
SomeproductsdonothaveaProgram/LEARNbutton.Inthiscase,theProgram/LEARNbuttonwillbelocatedinanexternalreceiver.Thereceiverwillbelocatedontheproductormountednearby.Followtheprogramminginstructionsforanexternalreceiver.
3
LOCaTE ThE PROgRaM/LEaRn BUTTOn
ChaMBERLain PRODUCTS
4
LOCaTE ThE PROgRaM/LEaRn BUTTOn
LearnCodeButton
ProgramSetButton
gEniE PRODUCTS
5
LOCaTE ThE PROgRaM/LEaRn BUTTOn
LinEaR PRODUCTS
LearnButton
LearnButton
ProgramSWButton
WaynE-DaLTOn PRODUCTS
6
Control Panel
LOCaTE ThE PROgRaM/LEaRn BUTTOn
LiFTMaSTER PRODUCTS
OvERhEaD DOOR PRODUCTS
YellowLearnButton
PurpleLearnButton
OrangeLearnButton
GreenLearnButton
PresstheLEARNbuttontwice.
LearnCodeButton
7
LOCaTE ThE LEaRn BUTTOn
STanLEy PRODUCTS
LearnButton
8
gaRagE DOOR OPEnERS
Programming to a garage Door Opener with a Program/LEaRn ButtonThe Program/LeaRn button is typically located on the back or side panel of the garage door opener or an external receiver. For help locating your Program/LeaRn button contact your garage door opener manufacturer.
If you have a LiftMaster or Chamberlain branded garage door opener with a yellow learn button, press and release the learn button, then press and hold the button on the remote control you would like to use. If programming is not successful, proceed through the steps below.
If you have a Genie® Intellicode® 2 garage door opener go to the next page.Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.
BottomButton
1 Startwithyourgaragedoorclosed. 2 PressandholdbottombuttonontheremotecontroluntiltheblueLEDstayssolid(approximately15seconds)thenreleasethebutton.
3 PressandreleasetheProgram/LEARNbuttononyourgaragedooropener.
4 Ontheremotecontrol,pressandreleasethebuttonthatyouwouldliketoprogramtwice.TheblueLEDwillblinkforupto60seconds.
5 6Waitforthegaragedoortomove,thenpressandreleaseeitherofthebuttonsontheremote.
LED
Testtheremotecontrolbypressingthebuttonyouprogrammedinstep4.Ifthegaragedooropenerdoesnotactivate,repeattheprogrammingsteps.
IMPORTANT: The remote will activate your garage door during programming. Ensure garage door is clear of ALL obstructions.
LED
9
Programming to a genie® intellicode® 2 garage Door OpenerBefore starting, you MUST have an existing Genie® Intellicode® 2 remote control programmed to the garage door opener. For help programming a Genie Intellicode 2 remote control, see your owner’s manual.Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.
gaRagE DOOR OPEnERS (continued)
1 2
3 4 Onthegaragedooropener,pressandholdthe Program/SetbuttonuntilboththelongandshortLED’slightupBLUE.
5
WaitfortheroundLEDonthegaragedooropenerto flashBLUEthenpressandreleaseeitherofthebuttonsontheremote.
6PressandreleasetheProgram/SetbuttonandthelongLEDwillflashPURPLE.
7 8
OntheGenie®remotecontrol,pressandreleasethebuttonthatisalreadyprogrammedtothegaragedooropener.BothLED’swillflashPURPLE.
BottomButton
Startwithyourgaragedoorclosed. PressandholdbottombuttonontheremotecontroluntiltheblueLEDstayssolid(approximately15seconds)thenreleasethebutton.
Ontheremotecontrol,pressandreleasethebuttonthatyouwouldliketoprogram3times.TheblueLEDwillblinkforupto60seconds.
Thegaragedoorwillopen.
LED
Testtheremotecontrolbypressingthebuttonyouprogrammedinstep7.Ifthegaragedooropenerdoesnotactivate,repeattheprogrammingsteps.
IMPORTANT: The remote will activate your garage door during programming. Ensure door is clear of ALL obstructions.
LED
10
Programming to a LiftMaster garage Door Opener Using the LEaRn Button on the Control PanelIfyouhaveaLiftMasterorChamberlainbrandedcontrolpanel,pressandreleasetheLEARNbuttontwice,thenpressandholdthebuttonontheremotecontrolyouwouldliketouse.Ifprogrammingisnotsuccessful,followthestepsbelow.
Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.
BottomButton
1 Startwithyourgaragedoorclosed. 2 PressandholdbottombuttonontheremotecontroluntiltheblueLEDstayssolid(approximately15seconds)thenreleasethebutton.
3 PressthecontrolpanelLEARNbuttontwice,theredlearnLEDwillturnon.
4 Ontheremotecontrol,pressandreleasethebuttonthatyouwouldliketoprogramtwice.TheblueLEDwillblinkforupto60seconds.
5 6Waitforthegaragedoortomove,thenpressandreleaseeitherofthebuttonsontheremote.
LED
Testtheremotecontrolbypressingthebuttonyouprogrammedinstep4.Ifthegaragedooropenerdoesnotactivate,repeattheprogrammingsteps.
IMPORTANT: The remote will activate your garage door during programming. Ensure garage door is clear of ALL obstructions.
LED
gaRagE DOOR OPEnERS (continued)
11
COMMERCiaL DOOR OPERaTORS
Programming to a Commercial Door Operator with a RaDiO ButtonThe RadIO button is typically located on the logic board of the operator or an external receiver. For help locating your RadIO button contact your commercial door operator manufacturer. Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.
RADIOButton
RADIOLED
RADIOButton
BottomButton
1 Startwithyourcommercialdoorclosed. 2 PressandholdbottombuttonontheremotecontroluntiltheblueLEDstayssolid(approximately15seconds)thenreleasethebutton.
3 PressandreleasetheRADIObuttononyourcommercialdooroperator.TheRADIOLEDwillilluminate.
WaittoseeiftheLEDontheoperatorflashesrapidly,indicatingtheremotecontrolisprogrammedtotheoperator.PressandreleasetheRADIObuttononyourcommercialdooroperatortoexitprogrammingmode.
4 Ontheremotecontrol,pressandreleasethebuttonthatyouwouldliketoprogramtwice.TheblueLEDwillblinkforupto60seconds.
5 6 Waitforcommercialdoortomove,thenpressandreleaseeitherbuttonontheremotecontroltoexitprogrammingmode.
LED
Testtheremotecontrolbypressingthebuttonyouprogrammedinstep4.Ifthecommercialdooroperatordoesnotactivate,repeattheprogrammingsteps.
IMPORTANT: The remote will activate your commercial door during programming. Ensure door is clear of ALL obstructions.
7
LED
12
Programming to a gate Operator with a Program/LEaRn ButtonThe Program/LeaRn button is typically located on the control board of the operator or an external receiver. For help locating your Program/LeaRn button contact your gate operator manufacturer.Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.
gaTE OPERaTORS
PressandreleasetheProgram/LEARNbutton*onyourgateoperator.TheProgram/LEARNLEDwillilluminate.
Program/LEARNButton*
*Dependingonyourproduct,theProgram/LEARNbuttonmayhaveadifferentname(usethebuttonforprogrammingremotecontrols).
BottomButton
1 Startwithyourgateclosed. 2 PressandholdbottombuttonontheremotecontroluntiltheblueLEDstayssolid(approximately15seconds)thenreleasethebutton.
3 4 Ontheremotecontrol,pressandreleasethebuttonthatyouwouldliketoprogramtwice.TheblueLEDwillblinkforupto60seconds.
5 6Waitforthegatetomoveortheprogram/LEARNLEDonthegateoperatorblinks,thenpressandreleaseeitherofthebuttonsontheremote.
LED
Testtheremotecontrolbypressingthebuttonyouprogrammedinstep4.Ifthegateoperatordoesnotactivate,repeattheprogrammingsteps.
IMPORTANT: The remote will activate your gate during programming. Ensure gate is clear of ALL obstructions.
LED
Program/LEARNLED
13
Programming to an External Receiver with a Program/LEaRn Button
EXTERnaL RECEivERS
PressandreleasetheProgram/LEARNbutton*ontheexternalreceiver.
Program/LEARNButton*
If using the Universal Mini Remote Control with residential door openers, the remote control must be used only with door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are always located on or near the bottom of the door track.
The external receiver is typically located on the product or mounted near the product. Theimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.
*Dependingonyourproduct,theProgram/SMART/LEARNbuttonmayhaveadifferentname(usethebuttonforprogrammingremotecontrols).
STOP
BottomButton
1 Startwithyourgaragedoor,commercialdoor,orgateclosed.
2 PressandholdbottombuttonontheremotecontroluntiltheblueLEDstayssolid(approximately15seconds)thenreleasethebutton.
3 4 Ontheremotecontrol,pressandreleasethebuttonthatyouwouldliketoprogramtwice.TheblueLEDwillblinkforupto60seconds.
5 6Waitforthedoororgatetomove,thenpressandreleaseeitherofthebuttonsontheremote.
LED
Testtheremotecontrolbypressingthebuttonyouprogrammedinstep4.Ifthegaragedooropener,commercialdooroperator,orgateoperatordoesnotactivate,repeattheprogrammingsteps.
IMPORTANT: The remote will activate your door or gate during programming. Ensure door or gate is clear of ALL obstructions.
LED
14
MyQ® LighT COnTROLS
Programming to a MyQ® Light ControlTheimagesthroughoutthismanualareforreferenceonlyandyourproductmaylookdifferent.
PressandreleasetheLEARNbuttononthemodule(theLEDonthemodulewilllight).
Button
1 Plugthelampintothemoduleandplugthemoduleintoanelectricaloutlet(theLEDonthemodulewillflash).NOTE: Make sure the lamp is switched ON.
2 IfthelampisnotON,pressandreleasethePowerbuttononthemoduletoturnthelampON.
3 4 Pressthebuttonontheremotecontrol.
5 Thelamp’slightbulbwillblinkandtheLEDonthemodulewillturnOFFwhenthedevicehasbeenprogrammed.
LED
15
nEED hELP?
The remote control does not have good range.
• Therangeoftheremotecontrolmayvarydependingonvariousfactorsandenvironmentalfactors
The remote control will not program to a product with a Program/LeaRn button.
• Checkthebatteryintheremotecontrol.TheLEDshouldlightwhenyoupressabutton.Replacethebatteryifnecessary.
The remote control Led will not light or it is dim.
• Replacethebattery.
The remote control Led does not activate the product until it is close to the product.
• Replacethebattery.
To prevent possible SERIOUS INJURY or DEATH:• NEVERallowsmallchildrennearbatteries.• Ifbatteryisswallowed,immediatelynotifydoctor.Toreduceriskoffire,explosionorchemicalburn:• ReplaceONLYwith3VCR2032coinbatteries.• DONOTrecharge,disassemble,heatabove212°F(100°C)
orincinerate.
NOTICE:TocomplywithFCCandorIndustryCanada(IC)rules,adjustmentormodificationsofthisreceiverand/ortransmitterareprohibited,exceptforchangingthecodesettingorreplacingthebattery.THEREARENOOTHERUSERSERVICEABLEPARTS.TestedtoComplywithFCCStandardsFORHOMEOROFFICEUSE.Operation is subjecttothefollowingtwoconditions:(1)thisdevicemaynotcauseharmfulinterference,and(2) thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.
ChamberlainandLiftMasterareTrademarksofChamberlainGroup.Genie isaTrademarkofOverheadDoorCorporation.OverheadDoorisaTrademarkofOverheadDoorCorporation.LinearisaTrademarkofLinearCorporation.MasterMechanicisaTrademarkofTruServ.SearsisaTrademarkofSears&Roebuck.StanleyisaTrademarkofTheStanleyWorks.WayneDaltonisatrademarkofWayneDaltonCorporation.DoItisatrademarkofDoItBestCorporation.
©2016,LiftMasterGDOPro103B AllRightsReserved
LiftMaster.com1-800-442-1255
BaTTERy
Disposeofbatteriesproperly.ReplaceONLYwith3VCR2032coinbatteries.
need Help?GotoLiftMaster.com/374ut orcall1-800-442-1255
Battery
Screw
Related Documents
