Top Banner
1 2 3 4 A 5 B 7 8 6 D C LED TORCH Product contents/ device parts 1 Torch 2 Lens attachment 3 Diffuser 4 Bag 5 On/Off switch 6 Battery holder 7 Battery compartment cover 8 Batteries, 3× The product contents include three type LR6 1.5 V batteries. General information Reading and storing the instruction manual This instruction manual accompanies this LED torch. It contains impor- tant information on setup and handling. For improved readability, the LED torch will be referred to only as the “torch” below. Before using the torch, please read through the instruction manual carefully. This particularly applies for the safety notes. Failure to heed this instruction manual may result in severe injury or damage to the torch. The instruction manual is based on the standards and rules in force in the European Union. When abroad, you must also observe country-specific guidelines and laws. Store the instruction manual for future use. If you pass the torch on to third parties, please be absolutely sure to include this instruction manual. Explanation of symbols The following symbols and signal words are used in this instruction manual, on the torch or on the packaging. WARNING! This signal symbol/word desig- nates a hazard with moderate degree of risk which may lead to death or severe injury if not avoided. ATTENTION! This signal symbol/word desig- nates a hazard with low risk that, if not avoided, may result in minor or moderate injury. NOTICE! This signal symbol/word warns against potential damages to property. This symbol provides you with useful sup- plementary informa- tion on assembly or operation. Risk Group 2 The LED belongs to risk group 2. Im- proper use of the torch may result in injury to your eyes. Declaration of conformity (see chapter “Declaration of conform- ity”): Products marked with this symbol meet all applicable Com- munity regulations for the Europe- an Economic Area. The “green dot” means that the torch must be disposed of in ac- cordance with the regulations and laws of your country. Safety Proper use The torch is only intended for illuminating indoor and outdoor areas. The torch is only intended for private use and not suitable for commercial purposes. Only use the torch as described in this instruction manual. Any other use is considered improper and may result in damage to property. The manufacturer or vendor accepts no liability for damage caused by improper or incorrect use. Safety notes WARNING! Danger of explosion! Batteries may explode if they are excessively heated up. Don't heat up the batteries and don't throw them in an open fire. Do not expose the battery and torch to direct sunlight. Do not short circuit the bat- teries. Never attempt to charge non-rechargeable batteries. ATTENTION! Risk of injury! The optical beam emitted by the torch could damage your eyes. Never look directly into the beam of the torch. Do not look at the beam of the torch for a prolonged period. Never dazzle other persons or animals with the torch. WARNING! Danger for children and per- sons with impaired physical, sensory or mental capaci- ties (e.g. partially disabled persons, older persons with reduced physical and mental capacities) or lack of expe- rience and knowledge (e.g. older children). Do not allow children to play with the torch. Keep children under eight years of age away from the torch. Store the batteries out of the reach of children. If children or animals swallow batteries, immediately contact a physician. Do not leave the torch unat- tended while in use. Change the batteries as soon as the light intensity starts to diminish. 1. Unscrew the battery compart- ment cover 7 and remove the battery holder 6 . 2. If necessary, take the old bat- teries out of the battery holder and dispose of them properly. 3. Insert the 3 batteries 8 in the battery holder according to the indicated polarity. 4. Push the battery holder into the torch housing. The battery holder can only be pushed into the housing in one direction. Using the torch Activating/deactivating the torch Keep in mind that the enclosed batteries have already been inserted. Push the On/ Off switch 5 on the battery compartment cover all the way to the stop point to switch the torch on and off. Changing operating modes You can choose from 3 operating modes for the torch. 1. Push the On/Off switch 5 to the stop point to switch the torch on. The maximum light intensity (100 %) has been set. 2. Only push the On/Off button gently to reduce the light in- tensity to 25 %. 3. Gently push the On/Off switch again to activate the SOS mode. The LED blinks in Morse code (3x short, 3x long, 3x short). 4. Push the On/Off switch to the stop point to switch off the torch. You can switch between the operating modes without switching off the torch. To do so, gently push the On/Off switch. NOTICE! Risk of damage! Handling the torch improperly may result in damage. Do not submerge the torch in water or other liquids. Never expose the torch to effects of the weather (rain etc.). Do not fill the torch with liquid. Make sure that children do not insert any objects in the housing. Keep the torch away from hot surfaces (e.g. hob, heater). If possible, do not drop the torch. Dispose of the torch if it is damaged. The LED cannot be replaced. Inserting/changing batteries WARNING! Risk of chemical burns! Leaking battery acid may lead to chemical burns. Do not allow battery acid to come into contact with skin, eyes or mucous membranes. Do not use your bare hands to remove battery fluid. Use conventional household washing gloves. If you do not use the torch for longer than one month, take the batteries out of the torch. Remove the empty batteries. NOTICE! Risk of damage! Improperly inserted batteries could damage the torch. Pay attention to the polarity +/- indicated on the battery holder and on the battery. Only insert the batteries in the battery holder with dry hands. Only replace the batteries with the same battery type. Never mix old and new batter- ies or batteries with different charges. Increasing/decreasing the beam To switch the beam from wide to focused illumination, push the lens attachment 2 away from the torch (see fig. C). To switch the beam from focused illumination to wide illumination, pull the lens attachment towards the torch (see fig. C). Using the diffuser Depending on your needs, the diffuser can turn your torch into a light for your tent, a reading light or a light for pleasant all-round lighting (see fig. D). 1. Mount the diffuser 3 on the lens attachment. 2. Take the diffuser back off of the lens attachment if you don't need it anymore. Cleaning NOTICE! Risk due to improper operation! Improperly cleaning the torch may damage it. Do not use any aggressive cleaners, brushes with metal or nylon bristles, as well as sharp or metallic cleaning utensils such as knives, hard scrapers and the like. They could dam- age the surfaces. Cleaning the lens 1. Screw the attachment ring off of the lens attachment 2 to remove the lens. 2. Use a soft cloth to clean the lens so that you do not scratch the lens. 3. Use a small amount of glass cleaner or rubbing alcohol for stubborn dirt. 4. During assembly, make sure that you screw the attachment ring back on properly. User Manual Spend a little Live a lot. Try now Just scan the QR code below with your smartphone to learn more about the Al- di product you purchased.* * When running the QR code reader, costs for the Internet connection may be incurred depending on your rate. ID: #05007 m y h a n s e c o n t r o l. c o m M A N U A L D E V E L O P E D I N G E R M A N Y User-friendly Manual PRODUCED IN CHINA FOR: ALDI STORES LTD. PO BOX 26, ATHERSTONE WARWICKSHIRE, CV9 2SH ALDI STORES (IRELAND) LTD. PO BOX 726, NAAS, CO. KILDARE. Visit us at www.aldi.com. AFTER SALES SUPPORT [email protected] +44 (0) 1909 517672 Model: WK 502 Product code: 92734 YEARS WARRANTY 11/2015 GB IRE WARRANTY CARD Description of malfunction: If after contacting the manufac- turer you are requested to return the faulty product please return the completed warranty card to- gether with it. JTM Contracts 1 Monument Park Pattinson Industrial estate Washington Tyne & Wear NE38 8QU UNITED KINGDOM [email protected] LED TORCH AFTER SALES SUPPORT [email protected] MODEL: WK 502 PRODUCT CODE: 92734 11/2015 +44 (0) 1909 517672 +353 (0) 12 475 437 GB IRE Your details: Name Address E-mail Date of purchase* * We recommend you keep the receipt with this warranty card. Location of purchase Logo, z. B. Maginon YEARS WARRANTY +353 (0) 12 475 437 GB IRE Free Hotline GB IRE
2

GB IRE Product contents/ ATTENTIoN! Logo, z. B. Maginon ......on your rate. ID: #05007 m y h a ... [email protected] +44 (0) 1909 517672 Model: WK 502 Product code: 92734 yEArS

Oct 03, 2020

Download

Documents

dariahiddleston
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Page 1: GB IRE Product contents/ ATTENTIoN! Logo, z. B. Maginon ......on your rate. ID: #05007 m y h a ... keyocr@jtmcontracts.com +44 (0) 1909 517672 Model: WK 502 Product code: 92734 yEArS

1

2

3

4

A

5

B7 8

6

DC

LED TorCh

Product contents/device parts

1 Torch

2 Lens attachment

3 Diffuser

4 Bag

5 On/Off switch

6 Battery holder

7 Battery compartment cover

8 Batteries, 3×

The product contents include three type LR6 1.5 V batteries.

General informationreading and storing the instruction manual

This instruction manual accompanies this LED torch. It contains impor-tant information on setup

and handling.For improved readability, the LED torch will be referred to only as the “torch” below.Before using the torch, please read through the instruction manual carefully. This particularly applies for the safety notes.Failure to heed this instruction manual may result in severe injury or damage to the torch. The instruction manual is based on the standards and rules in force in the European Union. When abroad, you must also observe country-specific guidelines and laws.Store the instruction manual for future use. If you pass the torch on to third parties, please be absolutely sure to include this instruction manual.

Explanation of symbolsThe following symbols and signal words are used in this instruction manual, on the torch or on the packaging.

WArNING!This signal symbol/word desig-nates a hazard with moderate degree of risk which may lead to death or severe injury if not avoided.

ATTENTIoN!This signal symbol/word desig-nates a hazard with low risk that, if not avoided, may result in minor or moderate injury.

NoTICE!

This signal symbol/word warns against potential damages to property.

This symbol provides you with useful sup-plementary informa-tion on assembly or operation.

Risk Group 2

The LED belongs to risk group 2. Im-proper use of the torch may result in injury to your eyes.

Declaration of conformity (see chapter “Declaration of conform-ity”): Products marked with this symbol meet all applicable Com-munity regulations for the Europe-an Economic Area.

The “green dot” means that the torch must be disposed of in ac-cordance with the regulations and laws of your country.

SafetyProper useThe torch is only intended for illuminating indoor and outdoor areas. The torch is only intended for private use and not suitable for commercial purposes.Only use the torch as described in this instruction manual. Any other use is considered improper and may result in damage to property.The manufacturer or vendor accepts no liability for damage caused by improper or incorrect use.

Safety notes

WArNING!Danger of explosion!Batteries may explode if they are excessively heated up.

− Don't heat up the batteries and don't throw them in an open fire.

− Do not expose the battery and torch to direct sunlight.

− Do not short circuit the bat-teries.

− Never attempt to charge non-rechargeable batteries.

ATTENTIoN!

risk of injury!The optical beam emitted by the torch could damage your eyes.

− Never look directly into the beam of the torch.

− Do not look at the beam of the torch for a prolonged period.

− Never dazzle other persons or animals with the torch.

WArNING!

Danger for children and per-sons with impaired physical, sensory or mental capaci-ties (e.g. partially disabled persons, older persons with reduced physical and mental capacities) or lack of expe-rience and knowledge (e.g. older children).

− Do not allow children to play with the torch.

− Keep children under eight years of age away from the torch.

− Store the batteries out of the reach of children.

− If children or animals swallow batteries, immediately contact a physician.

− Do not leave the torch unat-tended while in use.

Change the batteries as soon as the light intensity starts to diminish.

1. Unscrew the battery compart-ment cover 7 and remove the battery holder 6 .

2. If necessary, take the old bat-teries out of the battery holder and dispose of them properly.

3. Insert the 3 batteries 8 in the battery holder according to the indicated polarity.

4. Push the battery holder into the torch housing.

The battery holder can only be pushed into the housing in one direction.

Using the torchActivating/deactivating the torchKeep in mind that the enclosed batteries have already been inserted.

− Push the On/ Off switch 5 on the battery compartment cover all the way to the stop point to switch the torch on and off.

Changing operating modesYou can choose from 3 operating modes for the torch.

1. Push the On/Off switch 5 to the stop point to switch the torch on.The maximum light intensity (100 %) has been set.

2. Only push the On/Off button gently to reduce the light in-tensity to 25 %.

3. Gently push the On/Off switch again to activate the SOS mode.The LED blinks in Morse code (3x short, 3x long, 3x short).

4. Push the On/Off switch to the stop point to switch off the torch.

You can switch between the operating modes without switching off the torch. To do so, gently push the On/Off switch.

NoTICE!

risk of damage!Handling the torch improperly may result in damage.

− Do not submerge the torch in water or other liquids.

− Never expose the torch to effects of the weather (rain etc.).

− Do not fill the torch with liquid. − Make sure that children do

not insert any objects in the housing.

− Keep the torch away from hot surfaces (e.g. hob, heater).

− If possible, do not drop the torch.

− Dispose of the torch if it is damaged. The LED cannot be replaced.

Inserting/changing batteries

WArNING!risk of chemical burns!Leaking battery acid may lead to chemical burns.

− Do not allow battery acid to come into contact with skin, eyes or mucous membranes.

− Do not use your bare hands to remove battery fluid. Use conventional household washing gloves.

− If you do not use the torch for longer than one month, take the batteries out of the torch.

− Remove the empty batteries.

NoTICE!

risk of damage!Improperly inserted batteries could damage the torch.

− Pay attention to the polarity +/- indicated on the battery holder and on the battery.

− Only insert the batteries in the battery holder with dry hands.

− Only replace the batteries with the same battery type.

− Never mix old and new batter-ies or batteries with different charges.

Increasing/decreasing the beam

− To switch the beam from wide to focused illumination, push the lens attachment 2 away from the torch (see fig. C).

− To switch the beam from focused illumination to wide illumination, pull the lens attachment towards the torch (see fig. C).

Using the diffuserDepending on your needs, the diffuser can turn your torch into a light for your tent, a reading light or a light for pleasant all-round lighting (see fig. D).

1. Mount the diffuser 3 on the lens attachment.

2. Take the diffuser back off of the lens attachment if you don't need it anymore.

Cleaning

NoTICE!

risk due to improper operation!Improperly cleaning the torch may damage it.

− Do not use any aggressive cleaners, brushes with metal or nylon bristles, as well as sharp or metallic cleaning utensils such as knives, hard scrapers and the like. They could dam-age the surfaces.

Cleaning the lens1. Screw the attachment ring off

of the lens attachment 2 to remove the lens.

2. Use a soft cloth to clean the lens so that you do not scratch the lens.

3. Use a small amount of glass cleaner or rubbing alcohol for stubborn dirt.

4. During assembly, make sure that you screw the attachment ring back on properly.

User Manual

Spend a little Live a lot.

Try nowJust scan the QR code below with your smartphone to learn more about the Al-di product you purchased.*

* When running the QR code reader, costs for the Internet connection may be incurred depending on your rate.

ID: #05007

myhansecontrol.c

om

MA

NUA

L

DEVELOPED IN GERMA

NY

User-friendlyManual

ProDUCED IN ChINA for:ALDI STORES LTD. PO BOx 26, ATHERSTONEWARWICKSHIRE, CV9 2SH

ALDI STORES (IRELAND) LTD.PO BOx 726, NAAS, CO. KILDARE.Visit us at www.aldi.com.

AfTEr SALES SUPPorT

[email protected]

+44 (0) 1909 517672

Model: WK 502Product code: 92734

yEArSWArrANTy

11/2015

GB IRE

WArrANTy CArD

Description of malfunction:

If after contacting the manufac-turer you are requested to return the faulty product please return the completed warranty card to-gether with it.

JTM Contracts

1 Monument Park

Pattinson Industrial estate

Washington

Tyne & Wear

NE38 8QU

UNITED KINGDOM

[email protected]

LED TorCh

AfTEr SALES SUPPorT

[email protected]

MODEL: WK 502 PRODUCT CODE: 92734 11/2015

+44 (0) 1909 517672+353 (0) 12 475 437

GB

IrE

Your details:

Name Address

E-mail

Date of purchase* * We recommend you keep the receipt with this warranty card.

Location of purchase

Logo, z. B. Maginon

yEArSWArrANTy

+353 (0) 12 475 437GB

IrE

Free Hotline

GB IRE

Page 2: GB IRE Product contents/ ATTENTIoN! Logo, z. B. Maginon ......on your rate. ID: #05007 m y h a ... keyocr@jtmcontracts.com +44 (0) 1909 517672 Model: WK 502 Product code: 92734 yEArS

Transport − Use the carrying strap to

attach the torch e.g. to a belt or backpack.

TroubleshootingProblemThe torch does not light up.

Possible causesThe batteries have been inserted incorrectly, have not been inserted or are empty.

− Insert 3 LR03/AAA batteries in the battery holder and make sure that the polarity (+/-) corresponds to the indicated polarity.

Technical dataModel: WK 502

Articlenumber:

92734

Batteryoperation:

3 x 1.5 V AAA

LED: 5 watt Cree LED Chip xPG

Range: approx. 120 m

Luminous colour:

5,000 – 8,300 K

Luminous flux: ≤ 137 lumens +/-10 %

Light intensity: Focus: 9,000± 10 % LuxDefocus: 200± 10 % Lux

Service life of illuminant:

at least 50,000 hours

Material: Torch: aluminiumBag: nylon Diffuser: PC plastic

IP code: IP 65

Brightness levels:

100 % and 25 %

Colours: anthracite (matt) and black (shiny)

Declaration of conformityThe EU declaration of conformity can be requested from the address speci-fied on the warran-ty card (at the end of this instruction manual).

DisposalDisposing of the packaging

Dispose of the packaging separat-ed into single type materials. Dispose of cardboard and carton as waste pa-per and foils via the recyclable material collection service.

Disposing of the torch(Applicable in the European Union and other European states with systems for the separate collection of reusable waste materials)

old devices must not be disposed of with household waste! If the torch can no longer be used, every user is required by law

to dispose of old devices sepa-rately from their household waste, e.g. at a collection point in his community/borough. This en-sures that old devices are recycled in a professional manner and also rules out negative consequences for the environment. For this rea-son, electrical equipment is marked with the symbol shown here.

Warranty conditionsDear Customer,

The ALDI warranty offers you extensive benefits in addition to your statutory rights:

Warranty period: 3 years from date of purchase.

6 months for wear parts and consumables under normal and proper conditions of use (e.g. rechargeable batteries).

Costs: Free repair/exchange. No transport costs.

hotline: Calls cost 10p per minute from a landline, calls from mobiles may vary.

ADVICE: Please contact our service hotline by phone, e-mail or fax before sending in the device. This allows us to provide support in the event of possible operator errors.

In order to make a claim under the warranty, please send us:

• the faulty item together with the original purchase receipt and the completed warranty card.

• the faulty product with all components included in the packaging.

The warranty does not cover damage caused by:

• Accident or unanticipated events (e.g. lightning, water, fire). • Improper use or transport. • Disregard of the safety and maintenance instructions.• Other improper treatment or modification.

After the expiry of the warranty period, you still have the possibility to have your product repaired at your own expense. If the repair or the estimate of costs is not free of charge you will be informed ac-cordingly in advance.

This warranty does not affect your statutory rights. The period of warranty can only be extended in ac-cordance with a legal standard. In countries where a (compulsory) warranty and/or spare part storage and/or a system for compensation are/is required by law, the statutory minimum conditions apply. In the event that a product is received for repair, neither the service company nor the seller will assume any liability for data or settings possibly stored on the product by the customer.

Batteries and rechargeable batteries may not be dis-posed of with household waste! As the end user you are

required by law to bring all batteries and re-chargeable batteries, regardless whether they contain harmful

substances* or not, to a collection point run by the communal au-thority or borough or to a retailer, so that they can be disposed of in an environmentally friendly manner. * labelled with: Cd = cadmium, Hg = mercury, Pb = lead

Great care has gone into the manufacture of this product and it should therefore provide you with years of good service when used properly. In the event of product failure within its intended use over the course of the first 3 years after date of purchase, we will remedy the problem as quickly as possible once it has been brought to our attention. In the unlikely event of such an occurrence, or if you require any information about the product, please contact us via our helpline support services, details of which are to be found both in this manual and on the product itself.

GB IRE