Apply G-Premio BOND. Wait 10 seconds. 7 Remove excess. Excess can be tack cured for 1-2 seconds. 12 Dry with a MAXIMUM AIR PRESSURE for 5 seconds. 8 Light cure each surfaces/margins for 20 seconds (Halogen/LED 700mW/cm 2 ). 13 Light cure for 10 seconds (Halogen/LED 700mW/cm 2 ). 9 Finish and polish the margins. 14 ▲ PREPARATION OF TOOTH SURFACE ▲ CEMENTATION CEMENTATION TECHNIQUE FOR VENEERS G-CEM LinkForce TECHNIQUE GUIDE STORAGE CONDITION Store the System Kit/Starter Kit or G-CEM LinkForce syringes in refrigerator. Other components can also be stored at room temperature. Refer to respective instructions for use. LAYOUT of SYSTEM KIT LAYOUT of STARTER KIT Rinse and dry the prepared tooth. 5 Apply cement directly to the bonding surface of the veneer and/or tooth surface. 10 Select either Selective Etch or Total Etch technique. Rinse and dry. 6 Immediately seat onto prepared tooth. Maintain moderate pressure. 11 13009526 200762SK ▲ PREPARATION OF THE RESTORATION Prepare the restoration according to the manufacturer’s instructions. ▲ TRIAL FIT Remove the temporary restoration and clean thoroughly. 1 Check the fit & occlusion. As necessary, use G-CEM LinkForce Try-In Paste. 2 Apply G-Multi PRIMER. 3 Dry with an air syringe. 4 Etch with hydrofluoric acid. 1 Rinse and dry. 2 ▲ Glass ceramics Sandblast* *For CERASMART, alternatively apply hydrofluoric acid. 1 Blow clean with air syringe. Rinse and dry. 2 ▲ Hybrid ceramics & Composite Consult Instructions for Use Remove the restoration and rinse with water. 3 Disposable dispensing dish GC Automix Tip for G-CEM LinkForce G-Multi PRIMER G-Premio BOND G-CEM LinkForce Disposable applicator Disposable applicator G-MULTI PRIMER G-Premio BOND DCA G-Premio BOND Disposable dispensing dish G-CEM LinkForce Try-In Paste GC Etchant Disposable applicator Disposable dispensing dish Dispensing tips for GC ETCHANT and Try-In Paste Cover for Try-In Paste G-CEM LinkForce Try-In Paste GC ETCHANT G-Premio BOND DCA G-Multi PRIMER G-Premio BOND GC Automix Tip for G-CEM LinkForce LinkForce G-CEM LinkForce The tray can be removed and stored separately in the refrigerator. Empty slots are for storage of additional shades as you like. 5sec. 10sec. 10sec. 20 sec.
3
Embed
G-CEM LinkForce TechGuide-set-6P-CE - GC America TECHNIQUE FOR INLAYS, ONLAYS, CROWNS & BRIDGES CEMENTATION TECHNIQUE FOR POSTS AND CORES 12 Immediately seat onto prepared tooth/abutment.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Apply G-Premio BOND. Wait 10 seconds.
7
Remove excess. Excess can be tack cured for 1-2 seconds.
12
Dry with a MAXIMUM AIR PRESSURE for 5 seconds.
8
Light cure each surfaces/margins for 20 seconds (Halogen/LED 700mW/cm2).
13
Light cure for 10 seconds (Halogen/LED 700mW/cm2).
9
Finish and polish the margins.
14
Light cure each surface/margin for 20 seconds (Halogen/LED 700mW/cm2). 13
If light curing is not used, let it set for 4 minutes after seating. Finish and polish margins if necessary.
Remove excess while maintaining moderate pressure. Excess can be tack cured for 1-2 seconds for an easier excess removal.
▲
PREPARATION OF TOOTH SURFACE
▲
CEMENTATION
CEMENTATION TECHNIQUE FOR VENEERS G-CEM LinkForce TECHNIQUE GUIDE
STORAGE CONDITIONStore the System Kit/Starter Kit or G-CEM LinkForce syringes in refrigerator. Other components can also be stored at room temperature. Refer to respective instructions for use.
LAYOUT of SYSTEM KIT
LAYOUT of STARTER KIT
▲
PREPARATION OF THE RESTORATION Prepare the restoration according to the manufacturer’s instructions.
▲
PREPARATION OF POST SPACE
▲
CEMENTATION
▲
PREPARATION OF TOOTH SURFACE
▲
CEMENTATION
▲
Light-cure mode
▲
Alternative dual-cure mode
CEMENTATION TECHNIQUE FOR INLAYS, ONLAYS, CROWNS & BRIDGES CEMENTATION TECHNIQUE FOR POSTS AND CORES
If light curing is not used, let it set for 4 minutes after seating. Finish and polish margins if necessary.
Remove excess while maintaining moderate pressure. Excess can be tack cured for 1-2 seconds for an easier excess removal.
▲
PREPARATION OF TOOTH SURFACE
▲
CEMENTATION
CEMENTATION TECHNIQUE FOR VENEERS G-CEM LinkForce TECHNIQUE GUIDE
STORAGE CONDITIONStore the System Kit/Starter Kit or G-CEM LinkForce syringes in refrigerator. Other components can also be stored at room temperature. Refer to respective instructions for use.
LAYOUT of SYSTEM KIT
LAYOUT of STARTER KIT
▲
PREPARATION OF THE RESTORATION Prepare the restoration according to the manufacturer’s instructions.
▲
PREPARATION OF POST SPACE
▲
CEMENTATION
▲
PREPARATION OF TOOTH SURFACE
▲
CEMENTATION
▲
Light-cure mode
▲
Alternative dual-cure mode
CEMENTATION TECHNIQUE FOR INLAYS, ONLAYS, CROWNS & BRIDGES CEMENTATION TECHNIQUE FOR POSTS AND CORES
If light curing is not used, let it set for 4 minutes after seating. Finish and polish margins if necessary.
Remove excess while maintaining moderate pressure. Excess can be tack cured for 1-2 seconds for an easier excess removal.
▲
PREPARATION OF TOOTH SURFACE
▲
CEMENTATION
CEMENTATION TECHNIQUE FOR VENEERS G-CEM LinkForce TECHNIQUE GUIDE
STORAGE CONDITIONStore the System Kit/Starter Kit or G-CEM LinkForce syringes in refrigerator. Other components can also be stored at room temperature. Refer to respective instructions for use.
LAYOUT of SYSTEM KIT
LAYOUT of STARTER KIT
▲
PREPARATION OF THE RESTORATION Prepare the restoration according to the manufacturer’s instructions.
▲
PREPARATION OF POST SPACE
▲
CEMENTATION
▲
PREPARATION OF TOOTH SURFACE
▲
CEMENTATION
▲
Light-cure mode
▲
Alternative dual-cure mode
CEMENTATION TECHNIQUE FOR INLAYS, ONLAYS, CROWNS & BRIDGES CEMENTATION TECHNIQUE FOR POSTS AND CORES