01-3 FUSE AND RELAY korando 2010.10 8410-06 8410-06 Fuse and relay 1. CAUTIONS WHEN WORKING ON ELECTRICAL UNITS Remove the negative battery cable from the battery in advance when working on electrical units. - Make sure to turn "OFF" the ignition switch and other lamp switches before disconnecting or connecting the negative battery cable. (Otherwise, semiconductor parts can be damaged.) If a fuse is blown, replace it with a rated capacity fuse. If you use a fuse with capacity higher than the specification, corresponding parts can be damaged or a fire can break out. - Do not drop or apply excessive impact to sensors and relays. - 80℃ 10 A 15 A
24
Embed
Fuse and relay 8410-06 - neon.lofis.netneon.lofis.net/SsangYong/Service_Manuals/C200/C200_WML_302.pdf · 01-3 FUSE AND RELAY korando 2010.10 8410-06 Fuse and relay 8410-06 1. CAUTIONS
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
01-3
FUSE AND RELAYkorando 2010.10
8410-06
8410-06Fuse and relay
1. CAUTIONS WHEN WORKING ON ELECTRICAL UNITSRemove the negative battery cable from the battery in advance when working on electrical units.
-
Make sure to turn "OFF" the ignition switch and other lamp switches before disconnecting or connecting the negative battery cable. (Otherwise, semiconductor parts can be damaged.)
If a fuse is blown, replace it with a rated capacity fuse. If you use a fuse with capacity higher than the specification, corresponding parts can be damaged or a fire can break out.
-Do not drop or apply excessive impact to sensors and relays.
-
80℃
10 A 15 A
01-4
korando 2010.10
8410-06
FUSE AND RELAY
Make sure a connector is connected securely. Loose connection results in malfunction.
-
When disconnecting a connector equipped with a lock, press it down to the direction in the figure.
-
When checking voltage or continuity of the connector terminal with a circuit tester, insert the tester's probe from the harness side. For a seal type connector, the probe should be inserted through the hole in the rubber cap of the wiring. At this time, take care not to damage insulation of the wires and insert the probe until it contacts with the end of the connector terminal.
-
When inspecting the airbag system, make sure to use a diagnostic device, not a circuit tester.
01-5
FUSE AND RELAYkorando 2010.10
8410-06
2. CHECKING CABLES AND WIRESCheck for loose connection or rust.Check terminals and wires for corrosion due to electrolyte leakage.Check terminals and wires for open circuit.Check wire insulation and coat for damage, crack or deformation.Check that conducting parts of the terminals do not contact with other metal parts, such as vehicle body or other parts.Check that the grounding part has continuity with mounting bolts and vehicle body.Check that wires are properly routed.Make sure that wires are securely fixed to avoid contact with sharp body parts and high-temperature parts, such as the exhaust manifold and exhaust pipes.The rotating parts, such as fan pulley and fan belt, perturbative parts and wiring should be secured tightly at regular intervals.Wiring between fixed parts, such as the vehicle body, and vibrating parts, such as the engine, should be fixed after making it slack to afford vibration.
-----
---
-
-
01-6
korando 2010.10
8410-06
FUSE AND RELAY
ICM box
Interior fuse boxFuse box in engine compartment
There are 3 fuse & relay boxes in this vehicle.
2. SYSTEM LAYOUT
1. OVERVIEW
Fuse and relay box in engine compartmentInterior fuse boxICM (Integrated Control Module): Rear wiper, rear fog lamp, mirror folding, ACC, IGN1 & 2, horn, tailgate, power outlet, shift lock relay (A/T)
1.2.3.
01-7
FUSE AND RELAYkorando 2010.10
8410-06
3. OPERATING PROCESS1) Fuse & Relay Box in Engine CompartmentThe fuse & relay box is located beside the battery. It contains wiper, horn, heated wire, fog lamp, tail lamp and PTC relays. the B+ is supplied from ALT+.
Fuse & relay▶
01-8
korando 2010.10
8410-06
FUSE AND RELAY
Circuit diagram I▶
01-9
FUSE AND RELAYkorando 2010.10
8410-06
Circuit diagram II▶
01-10
korando 2010.10
8410-06
FUSE AND RELAY
Fuse & relay box III▶
01-11
FUSE AND RELAYkorando 2010.10
8410-06
2) Interior Fuse BoxThis fuse box is located in the left side of instrument panel.
Fuse & relay▶
01-12
korando 2010.10
8410-06
FUSE AND RELAY
Circuit diagram I▶
01-13
FUSE AND RELAYkorando 2010.10
8410-06
Circuit diagram II▶
01-14
korando 2010.10
8410-06
FUSE AND RELAY
3) ICM Box
Function descriptions▶
01-15
FUSE AND RELAYkorando 2010.10
8410-06
Connector A
Pin No. Function
1 -
2 -
3 -
4 -
5 B+ (CE box)
Pin No. Function
6 Fuse box
7 Fuse box
8 B+ (CE box)
9 -
10 Ground
Connector B
Pin No. Function
1 Multifunction switch (RH)
2 ACC (F47)
3 BCM (Mirror folding control)
4 BCM
5 ICM "C10"
6 IGN2 (F39)
7 Rear wiper motor
Pin No. Function
8 Rear wiper motor
9 Front & rear power outlet
10 B+ (F46)
11 Fuse box
12 Ground
13 BCM (Mirror unfolding control)
14 Mirror unfolding motor
01-16
korando 2010.10
8410-06
FUSE AND RELAY
Connector C
Pin No. Function
1 Stop lamp switch
2 BCM
3 IGN (F31)
4 BCM
5 B+ (F45)
6 Rear fog lamp
7 TGS lever
8 TGS lever
Pin No. Function
9 Warning horn
10 B+ (F42)
11 Tailgate actuator
12 B+ (F45)
13 Mirror folding motor
14 Ground
15 ICM "C16"
16 B+ (F52)
01-17
FUSE AND RELAYkorando 2010.10
8410-06
ICM box is located behind the instrument cluster.
Circuit board▶
01-18
korando 2010.10
8410-06
FUSE AND RELAY
4) Operating Process by Power Supply
(1) Rear wiper relay
(2) Rear fog lamp relay
Power supply: SB4, No. 39, ICM B6When turning ON/OFF the wiper switch with IGN2 ON, the rear wiper motor relay is turned ON/OFF.
When pressing the rear fog lamp switch with IGN2 ON (headlamp ON condition), the rear fog lamps are turned ON. When pressing the rear fog lamp switch again during the operation, the rear fog lamps are turned OFF.The rear fog lamps do not come ON when the engine is not running or the light switch is OFF. The rear fog lamps should not automatically come on again if they have been turned OFF by any other way other than the switch.
1.
2.
3.4.
Power supply: Memory fuse in CE box, Interior fuse box No. 52Operating signal: BCM A11 (ON/OFF)
Operating conditions▶
01-19
FUSE AND RELAYkorando 2010.10
8410-06
(3) Outside mirror folding/unfolding relay
Power supply: CE box No. 45Operating signal: BCM D16, D17 (Folding/Unfolding)
Manual operation▶
When pressing the mirror folding/unfolding switch with IGN ON, the mirrors are folded or un-floded according to the mirror condition in 16±6 seconds.