-
1109K–01
A62391
C/OPN Relay
B00679
–FUEL FUEL SYSTEM (2AZ–FE)11–1
1445Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
FUEL SYSTEM (2AZ–FE)PRECAUTION1. PRECAUTION(a) Before working on
fuel system, disconnect negative (–) terminal cable from
battery.(b) Do not smoke or work near an open flame when working on
fuel system.(c) Keep gasoline away from rubber or leather
parts.
2. WORK FOR PREVENT GASOLINE FROM SPILLINGOUT
CAUTION:� Perform disconnecting operation of the fuel system
parts after working for prevent gasoline form spillingout.
� As there is remained pressure in the fuel line afterworking
for prevent gasoline from spilling out, pre-vent it from splashing
inside the vehicle compart-ment by covering them with a shop
rag.
(a) Remove the circuit opening relay in the engine room
relayblock.
(b) Start the engine. After the engine has stopped on its
own,turn the ignition switch OFF.
HINT:There is a case that DTC P0171 (system to lean) is
output.(c) Check that the engine does not start.(d) Remove the fuel
tank cap, and let the air out of the fuel
tank.(e) Disconnect negative (–) terminal cable from battery.(f)
Reinstall the circuit opening relay.3. FUEL SYSTEM(a) When
disconnecting the high fuel pressure line, a large
amount of gasoline will spill out, so observe these
proce-dures.(1) Work for prevent gasoline from spilling out.(2)
Disconnect the fuel pump tube.
(See page 11–15)(3) Drain the fuel remained inside the fuel pump
tube.
(4) Prevent the disconnected fuel pump tube fromdamaging and
mixing foreign objects by coveringthem with a vinyl bag.
-
B00347
WRONG
CORRECT
Delivery Pipe
New O–ring
InjectorA51878
Delivery Pipe
O–ring
GrommetB09613
O–ring Retainer Pipe
Nylon Tube HousingA50709
11–2–FUEL FUEL SYSTEM (2AZ–FE)
1446Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
(5) Put a container under the connection.
(b) Observe these precautions when removing and installingthe
injector.(1) Never reuse the O–ring.(2) When placing a new O–ring
on the injector, take
care not to damage it in any way.(3) Coat a new O–ring with
spindle oil or gasoline be-
fore installing. Never use engine, gear or brake oil.
(c) Install the injector to the delivery pipe and cylinder
head,as shown in the illustration. Before installing the
injector,be sure to apply spindle oil or gasoline on the place
wherethe delivery pipe touches O–ring of the injector.
(d) Observe these precautions when disconnecting the
fueldelivery pipe.
HINT:The structure of the metallic connector is shown as
left.
(1) Remove the fuel pipe clamp No.2.
-
A60818
SST
Retainer(at 4 places)
B09615
A60083
Fuel Pipe Clamp No.1
A
A
B12941
B12944
–FUEL FUEL SYSTEM (2AZ–FE)11–3
1447Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
(2) Find the metallic connector of the fuel tube assem-bly, pull
it out towards the rear and hold it as it is.
(3) Assemble SST to the connection as shown.SST 09268–21010
(4) Turn SST, align the retainers inside the connectorwith SST
chamfered parts and insert SST into theconnector.
(5) Slide SST and the connector together towards thefuel tube
assembly.
(e) Observe these following precautions when disconnectingthe
fuel tube connector (quick type).(1) Remove the fuel pipe clamp
No.1.(2) Check if there is any dirt like mud on the pipe and
around the connector before disconnecting themand clean the dirt
away.
(3) Disconnect the connector from the hose whilepinching part A
with fingers as shown in the illustra-tion.
(4) When the connector and the pipe are stuck, pinchthe fuel
pipe between the hands, push and pull theconnector to free to
disconnect and pull it out. Donot use any tool at this time.
(5) Inspect if there is any dirt or the likes on the seal
sur-face of the disconnected pipe and clean it away.
-
Vinyl Bag
A52581
11–4–FUEL FUEL SYSTEM (2AZ–FE)
1448Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
(6) Prevent the disconnected pipe and connector fromdamaging and
mixing foreign objects by coveringthem with a vinyl bag.
4. CHECK FUEL LEAK(a) Check that there are no fuel leaks after
doing maintenance anywhere on the fuel system.
(See page 11–5)
-
11023–02
Fuel Tube Connector
A50710
A60083
Fuel Pipe Clamp No.1
A
A
B12941
–FUEL FUEL SYSTEM (2AZ–FE)11–5
1449Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
ON–VEHICLE INSPECTION
1. CHECK FUEL PRESSURE(a) Prepare for inspection.
(1) Purchase the new fuel tube and take out the fueltube
connector from its pipe.
HINT:Part No. 23901–28130
(b) Work for prevent gasoline from spilling out.(See page
11–1)
(c) Remove the fuel pipe clamp No.1 from the fuel tube
con-nector.
(d) Disconnect the fuel tube connector from the fuel pipewhile
pinching part A with fingers as shown in the illustra-tion.
CAUTION:� Perform disconnecting operations of the fuel tube
connector (quick type) after observing the precau-tions.
� As there is retained pressure in the fuel pipe line, pre-vent
it from splashing inside the engine compart-ment.
-
Fuel tube
Fuel Tube Connector
SST(Clip)
SST (T joint)SST
SST(Hose)
Fuel tube
Fuel Tube Connector
SST(Clip)
SST (T joint)SST
SST(Hose)
A52613
11–6–FUEL FUEL SYSTEM (2AZ–FE)
1450Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
(e) Install SST (pressure gauge) as shown in the illustrationby
using SST and fuel tube connector.SST 09268–41047 (90467–13001,
95336–08070),
09268–45012 (09268–41250)(f) Wipe off any splattered
gasoline.(g) Reconnect the negative (–) terminal cable to the
battery.(h) Connect the hand–hand tester to the DLC3.(i) Measure
the fuel pressure regulator.
Fuel pressure:304 – 343 kPa (3.1 – 3.5 kgf/cm 2, 44 – 50
psi)
If pressure is high, replace the fuel pressure regulator.If
pressure is low, check the fuel hoses and connections, fuelpump,
fuel filter and fuel pressure regulator.(j) Disconnect the
hand–held tester from the DLC3.(k) Start the engine.(l) Measure the
fuel pressure at idle.
Fuel pressure:304 – 343 kPa (3.1 – 3.5 kgf/cm 2, 44 – 50
psi)
(m) Stop the engine.(n) Check that the fuel pressure remains as
specified for 5
minutes after the engine has stopped.Fuel pressure: 147 kPa (1.5
kgf/cm 2, 21 psi) or more
If pressure is not as specified, check the fuel pump,
pressureregulator and/or injectors.(o) After checking fuel
pressure, disconnect the negative (–)
terminal cable from the battery and carefully remove theSST and
fuel tube connector to prevent gasoline fromsplashing.
(p) Reconnect the fuel tube (fuel tube
connector).CAUTION:Perform connecting operations of the fuel tube
connector(quick type) after observing the precautions.2. CHECK FUEL
PUMP OPERATION AND FUEL LEAK(a) When using hand–held tester
(1) Connect the hand–held tester to the DLC3.(2) Turn the
ignition switch ON and hand–held tester
main switch ON.NOTICE:Do not start the engine.
(3) Select the active test mode on the hand–held tester.(4)
Please refer to the hand–held tester operator’s
manual for further details.
-
A62390
FP+B
–FUEL FUEL SYSTEM (2AZ–FE)11–7
1451Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
(b) When not using hand–held tester(1) Remove the circuit
opening relay.(2) Using a service wire connect terminals FP and
+B
of the relay block.NOTICE:Pay due attention to the terminal
connecting position toavoid a malfunction.
(3) Turn the ignition switch ON, and check that the fuelpump
operates.
NOTICE:Do not start the engine.(c) Check that there are no fuel
leaks after doing mainte-
nance anywhere on the fuel system.
-
11024–02
Fuel Tube Connector
A50710
Fuel Tube Connector
SST(Hose)
B12947
SST (Hose)
SST(Clamp)
Vinyl Tube
SST (Union)
O–Ring
A51875
11–8–FUEL FUEL SYSTEM (2AZ–FE)
1452Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
INSPECTION1. FUEL INJECTOR ASSY
(a) Inspect injector resistance(1) Using an ohmmeter, measure
the resistance be-
tween the terminals.Resistance: 13.4 – 14.2 Ω at 20�C (68�F)
If the resistance is not as specified, replace the injector.(b)
Inspect injector inspectionCAUTION:Keep injector clear of sparks
during the test.
(1) Purchase the new fuel tube and take out the fueltube
connector from its pipe.
HINT:Part No. 23901–28130
(2) Connect SST and fuel tube connector to the fuelpipe.
SST 09268–41047 (90467–13001, 95336–08070)CAUTION:Perform
connecting operations of the fuel tube connector(quick type) after
observing the precautions.
(3) Install the O–ring to the injector.(4) Connect SST (union
and hose) to the injector, and
hold the injector and union with SST (clamp)SST 09268–41047
(09268–41110, 09268–41300,
90467–13001, 95336–08070)(5) Put the injector into a graduated
cylinder.
HINT:Install a suitable vinyl tube onto the injector to prevent
gasolinefrom splashing out.
(6) Operate the fuel pump.(See Page 11–5)
-
SST
A50700
B00069
A16628 A32859
–FUEL FUEL SYSTEM (2AZ–FE)11–9
1453Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
(7) Connect SST to the connector of injector.(8) Connect SST
(wire) to the battery for 15 seconds,
and measure the injection volume with a graduatedcylinder. Test
each injector 2 or 3 time.
SST 09842–30080Injection volume:
Injection volume Difference between each injector
68 – 82 cm3 (4.1 – 4.9 cu in.)per 15 seconds
14 cm3 (0.9 cu in.) or less
NOTICE:Always do the switching at the battery side.If the
injection volume is not as specified, replace the injector.
(c) Inspect leakage(1) In the condition above, disconnect the
test probes
of SST (wire) from the battery and check the fuelleakage from
the injector.
Fuel drop: 1 drop or less per 12 minutes
2. FUEL PUMP
(a) Insect fuel pump resistance.(1) Using an ohmmeter, measure
the resistance be-
tween terminals.Resistance: 0.2 – 3.0 Ω at 20�C (68�F)
(b) Inspect fuel pump operation(1) Apply battery voltage to both
terminals. Check that
the pump operates.NOTICE:� These tests must be done quickly
(within 10 seconds)
to prevent the coil from burning out.� Keep fuel pump as far
away from the battery as pos-
sible.� Always do the switching at the battery side.
-
1109L–01
A60820
N⋅m (kgf⋅cm, ft⋅lbf) : Specified torque
� Non–reusable part
Air Cleaner Cap w/ Air Cleaner Hose
Fuel Delivery Pipe
� O–ring
� Insulator
Fuel Injector Assy
20 (204, 15)
20 (204, 15)
Engine Wire
Engine Cover Sub–assy No. 1
Ventilation Hose No. 2
11–10–FUEL FUEL INJECTOR ASSY (2AZ–FE)
1454Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
FUEL INJECTOR ASSY (2AZ–FE)COMPONENTS
-
11021–02
A52073
Insulator
O–RingA50145
Push
Turn
Connector
B09635
–FUEL FUEL INJECTOR ASSY (2AZ–FE)11–11
1455Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
REPLACEMENT1. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT(See
page 11–1)2. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE3. REMOVE
ENGINE COVER SUB–ASSY NO.1
4. DISCONNECT FUEL TUBE SUB–ASSY(See page 11–1)
5. REMOVE FUEL DELIVERY PIPE W/INJECTORNOTICE:Be careful not to
drop the injectors when removing the de-livery pipe.(a) Remove the
ventilation hose No. 2.(b) Disconnect 4 injector connecters from
the injector.(c) Remove 2 clamp and wire harness from the delivery
pipe.(d) Remove 2 bolts and delivery pipe together with 4
injector.(e) Remove 2 spacers from the cylinder head.
6. REMOVE FUEL INJECTOR ASSY
(a) Pull out 4 injector from the delivery pipe.
7. INSTALL FUEL INJECTOR ASSY
(a) Install the new insulator to each injector.(b) Apply a light
coat of spindle oil or gasoline to new O–ring
and install them to each injector.
(c) Apply a light coat of spindle oil or gasoline on the
placewhere a delivery pipe touches on O–ring.
(d) While turning the injector clockwise and counterclock-wise,
push it to the delivery pipes. install 4 injectors.
NOTICE:� Be careful not to twist the O–ring.� After installing
injectors, check that they turns smoo-
thy. If an injector dose not, reinsiall it with a new
O–ring.
(e) Position the injector connector downward.
-
Spacer
B09636
A52073
11–12–FUEL FUEL INJECTOR ASSY (2AZ–FE)
1456Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
8. INSTALL FUEL DELIVERY PIPE W/INJECTOR(a) Place 2 spacers in
position on the cylinder head.(b) Place the delivery pipe together
with 4 injectors in position
on the cylinder head.
(c) Temporarily install 2 bolts holding the delivery pipe to
thecylinder.
(d) Check that the injectors rotate smoothly.HINT:If injectors
do not rotate smoothly, the probable cause is incor-rect
installation of O–ring. Replace the O–ring.(e) Position the
injector connector outward.(f) Tighten 2 bolts holding the delivery
pipe to the cylinder
head.Torque: 20 N ⋅m (204 kgf ⋅cm, 15 ft ⋅lbf)
9. INSPECT FUEL LEAK(See page 11–5 )
-
1109M–01
A57122
Rear Seat Cushion Pad
Rear Floor Service Hole Cover
Fuel Tank Vent Tube Set Plate
Fuel Suction Tube Assy w/ Pump & Gage
Fuel Pump Tube Sub–assy
� Non–reusable part
N·m (kgf·cm, ft·lbf) : Specified torque
� Fuel Suction Tube Set Gasket
3.5 (36, 31 in. ⋅lbf)
–FUEL FUEL PUMP ASSY (2AZ–FE)11–13
1457Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
FUEL PUMP ASSY (2AZ–FE)COMPONENTS
-
A57123� Non–reusable part
Fuel Pump Harness
Fuel Sender Gage Assy
Fuel Suction PlateSub–assy
Fuel Pump
Fuel Filter Assy
Fuel Pump Filter
Fuel Suction Support No.2
Fuel Pressure Regulator Assy
� O–ring
Cushion Rubber
� Clip
11–14–FUEL FUEL PUMP ASSY (2AZ–FE)
1458Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
-
1109N–01
A52585
O–ring
Fuel Pump Tube
ClipO–ring
Fuel Suction Plate
Fuel Tube Joint
A52589
A52586
–FUEL FUEL PUMP ASSY (2AZ–FE)11–15
1459Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
Removal & Installation and Disassembly & Reassembly1.
REMOVE REAR SEAT CUSHION ASSEMBLY2. REMOVE REAR FLOOR SERVICE HOLE
COVER
(a) Remove the service hole cover.(b) Disconnect the fuel pump
connector.3. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT (See
page 11–1)
4. SEPARATE FUEL PUMP TUBE SUB–ASSY
(a) Check if there is any dirt like mud around the
connectorbefore this work and clean dirt away.
(b) Remove the joint clip, and pull out the fuel pump
tube.NOTICE:� Be careful of dirt like mud because the quick
connec-
tor has an O–ring to seal the pipe and the connector.� Do not
use any tool in this work.� Do not bend or twist the nylon tube by
force.� Keep off plug from foreign subjects.� To protect the fuel
tube, cover it with a vinyl bag after
checking.
5. REMOVE FUEL TANK VENT TUBE SET PLATE
(a) Remove the 8 bolts and fuel tank vent tube set plate.
6. REMOVE FUEL SUCTION TUBE ASSY W/ PUMP & GAGE(a) Pull out
the fuel suction w/pump & gage from the fuel tank.NOTICE:� Do
not damage the fuel pump filter.� Be careful that the arm of the
sender gage should not bent.
(b) Remove the fuel suction tube gasket.
-
A52586
11–16–FUEL FUEL PUMP ASSY (2AZ–FE)
1460Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
7. REMOVE FUEL SUCTION SUPPORT NO.2
(a) Using a screwdriver, disconnect the snap claws from the claw
holes and remove the fuel suction sup-port No.2.
8. REMOVE FUEL PUMP CUSHION RUBBER
9. REMOVE FUEL PRESSURE REGULATOR ASSY
10. REMOVE FUEL PUMP ASSY W/FILTER(a) Disconnect the fuel pump
connector from the fuel pump.(b) Pull out the fuel filter and the
fuel pump assembly.11. REMOVE FUEL PUMP FILTER
(a) Using a screwdriver, remove the fuel pump filter clip and
the fuel pump filter.12. REMOVE FUEL SUCTION PLATE SUB–ASSY
(a) Using a screwdriver, disconnect the snap claws from the claw
holes and remove the fuel suction plate.13. REMOVE FUEL SENDER GAGE
ASSY
(a) Unlock the sender gage, and move it downward to remove.14.
REMOVE FUEL PUMP HARNESS
(a) Disconnect the connector, and remove the fuel pump
harness.15. INSTALL FUEL SENDER GAGE ASSY
(a) Lock the sender gage by pushing it upward.NOTICE:By pushing
the sender gage downward, confirm that it is certainly locked.16.
INSTALL FUEL PUMP FILTER
(a) Install the fuel pump filter with a new fuel pump filter
clip.17. INSTALL FUEL PRESSURE REGULATOR ASSY
(a) Apply gasoline to a new O–ring, and install it to the
pressure regulator.(b) Insert the pressure regulator.18. INSTALL
FUEL SUCTION TUBE ASSY W/ PUMP & GAGE(a) Install a new gasket
and fuel suction tube w/pump & gage.
19. INSTALL FUEL TANK VENT TUBE SET PLATE
(a) Install the fuel tank vent tube set plate with the 8 bolts.
3.5 N·m (36 kgf·cm, 31 in.·lbf)
-
A57126
–FUEL FUEL PUMP ASSY (2AZ–FE)11–17
1461Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
20. INSTALL FUEL PUMP TUBE SUB–ASSY
(a) Connect the main tube with the tube joint clip.NOTICE:�
Check that there is no scratch or foreign objects on
the connecting part.� Check that the connector is inserted fully
and secure-
ly.� Check that the clip of the tube joint is on the coller
of
the connector.� After installing the clip of the tube joint,
check that the
connector is not pulled off.21. INSTALL REAR FLOOR SERVICE HOLE
COVER
(a) Using a new butyl tape set, and install the rear floor
service hole cover.22. INSPECT FUEL LEAK
-
1109O–01
A57122
Rear Seat Cushion Pad
Rear Floor Service Hole Cover
Fuel Tank Vent Tube Set Plate
Fuel Suction Tube Assy w/ Pump & Gage
Fuel Pump Tube Sub–assy
� Non–reusable part
N·m (kgf·cm, ft·lbf) : Specified torque
� Fuel Suction Tube Set Gasket
3.5 (36, 31 in. ⋅lbf)
11–18–FUEL FUEL TANK ASSY (2AZ–FE)
1462Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
FUEL TANK ASSY (2AZ–FE)COMPONENTS
-
A62249
Pin
Parking Brake Cable Assy No. 2
Fuel Tank ProtectorLower Center
Fuel Tank Band Sub–assy No.1 RH
Exhaust Center Pipe Assy
Floor Panel Brace Rear
� Exhaust Pipe Gasket
Fuel Tank Band Sub–assy No.1 LH
Parking Brake Cable Assy No. 3
� Non–reusable part
N·m (kgf·cm, ft·lbf) : Specified torque
� Exhaust Pipe Gasket
39 (400, 29)
5.4 (55, 48 in. ⋅lbf)
39 (400, 29)
56 (571, 41)
5.4 (55, 48 in. ⋅lbf)
56 (571, 41)
19.5 (199 ,14)
5.4 (55, 48 in. ⋅lbf)
�
�
–FUEL FUEL TANK ASSY (2AZ–FE)11–19
1463Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
-
A57125� Non–reusable part
N·m (kgf·cm, ft·lbf) : Specified torque
Charcoal Canister Assy
Fuel Tank Protector No.3
Fuel Cut Off Valve Assy w /Tube
Fuel Tank Over Fill Check Valve Assy
Location of Fuel Tank Cushion
Fuel Tank Inlet Pipe Sub–assy
Fuel Pump Tube Sub–assy
Fuel Main Tube Support
�Check Valve Gasket
�Fuel Tank Breather Tube Gasket
Fuel Tank Protector Sub–assy No.1
5.4 (55, 48 in. ⋅lbf)
11–20–FUEL FUEL TANK ASSY (2AZ–FE)
1464Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
-
1109P–01
A57127
A57128
–FUEL FUEL TANK ASSY (2AZ–FE)11–21
1465Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
Removal & Installation and Disassembly & Reassembly1.
REMOVE REAR SEAT CUSHION PAD
2. REMOVE REAR FLOOR SERVICE HOLE COVER (See page 11–15)
3. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT (See page
11–26)4. REMOVE FUEL PUMP TUBE SUB–ASSY
(See page 11–15)5. REMOVE FUEL TANK VENT TUBE SET PLATE
6. REMOVE FUEL SUCTION TUBE ASSY W/ PUMP & GAGE7. DRAIN
FUEL8. REMOVE FLOOR PANEL BRACE REAR
(See page 15–2)9. REMOVE EXHAUST PIPE ASSY CENTER
10. DISCONNECT PARKING BRAKE CABLE ASSY NO.2
(a) Remove the bolt and nut, and disconnect the parkingbrake
cable.
11. DISCONNECT PARKING BRAKE CABLE ASSY NO.3
(a) Remove the bolt and nut, and disconnect the parkingbrake
cable.
12. REMOVE FUEL TANK PROTECTOR LOWER CENTER
(a) Remove the 4 bolts and the protector.
-
A57129
A57130
B01253
Push
Pinch
Pinch
AA
11–22–FUEL FUEL TANK ASSY (2AZ–FE)
1466Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
13. DISCONNECT FUEL PUMP TUBE SUB–ASSY
(a) Pinch the fuel pump tube connector clip and then pull outthe
tube.
NOTICE:� Check if there is any dirt like mud around the
connec-
tor before this work and clean the dirt away.� Be careful of
dirt like mud because the quick connec-
tor has an O–ring to seal the pipe and the connector.� Do not
use any tool in this work.� Do not bend or twist the nylon tube by
force.� After disconnecting the tube, cover the connector
with a vinyl bag.� When the connector and the pipe are stuck,
pinch the
tube between fingers, and turn it carefully to free andthen
disconnect the tube.
14. DISCONNECT FUEL TANK TO FILLER PIPE HOSE
(a) Disconnect the fuel tank to filler pipe hose from the fuel
tank.15. DISCONNECT FUEL TANK BREATHER HOSE
(a) Disconnect the fuel tank breather hose from the fuel
tank.16. REMOVE FUEL TANK ASSY
(a) Set the mission jack to the fuel tank.(b) Remove the fuel
tank bands.(c) Disconnect the valve to fuel filler pipe hose from
the fuel
tank over fill check valve.(d) Disconnect the fuel hose No. 3
from the fuel tank.
(e) Disconnect the vent line hose from the charcoal canister.(1)
Push the connector deep inside.(2) Pinch portion A.(3) Pull out the
connector.
(f) Disconnect the fuel emission hose from the charcoal
can-ister.
(g) Carefully, remove the fuel tank assembly from the
vehicle.
-
A57334
A60815
Clip Remover
Gasket
Valve
A57336
A57337
–FUEL FUEL TANK ASSY (2AZ–FE)11–23
1467Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
17. REMOVE FUEL TANK OVER FILL CHECK VALVEASSY
(a) Using a screwdriver, unlock the claw and remove the
pro-tector by turning it counter clockwise.
(b) Insert a clip remover between the check valve and thegasket,
remove the valve by gradually pushing it upward.
NOTICE:� Work accurately to maintain the sealing performance
of the check valve, since it is made from resin. It iseasy to
damage by removing and installing forcibly.
� Be sure to install new check valve and gasket.
18. REMOVE FUEL TANK PROTECTOR NO.3
(a) Remove the fuel tank protector No. 3 by sliding as shownin
the illustration.
19. REMOVE FUEL TANK PROTECTOR SUB–ASSY NO.1
(a) Remove the fuel tank protector No. 1 by sliding as shownin
the illustration.
-
A60493
ValveGasket
A60495
A60494
Apply light oil around the valve
11–24–FUEL FUEL TANK ASSY (2AZ–FE)
1468Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
20. REMOVE FUEL CUT OFF W/TUBE VALVE ASSY
(a) Using a screwdriver, unlock the claw and remove the
pro-tector by turning it counter clockwise.
(b) Insert a clip remover between the cut off valve and
thegasket, remove the cut off valve by gradually pushing
itupward.
NOTICE:� Work accurately to maintain the sealing performance
of the cut off valve, since it is made from resin. It iseasy to
damage by removing and installing forcibly.
� Be sure to install new cut off valve and gasket.21. REMOVE
FUEL MAIN TUBE SUPPORT
22. REMOVE FUEL TANK CUSHION NO.1
23. REMOVE FUEL TANK CUSHION NO.2
24. INSTALL FUEL TANK CUSHION NO.1
(a) Install new fuel tank cushions as shown in the
illustration.25. INSTALL FUEL TANK CUSHION NO.2
(a) Install new fuel tank cushion as shown in the
illustration.
26. INSTALL FUEL MAIN TUBE SUPPORT
Torque: 5.4 N ⋅m (55 kgf ⋅cm, 48 in. ⋅lbf)
27. INSTALL FUEL CUT OFF W/TUBE VALVE ASSY
(a) Install a new gasket to the fuel tank.(b) Apply light oil
around the new fuel cut off valve as shown
in the illustration, and insert it into the tank without
force.Be careful not to drop the gasket into the tank.
(c) Check that the fuel cut off valve is fully inserted.
-
A60496
Apply light oil around the valve
A57340
–FUEL FUEL TANK ASSY (2AZ–FE)11–25
1469Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
28. INSTALL FUEL TANK OVER FILL CHECK VALVEASSY
(a) Install a new gasket to the fuel tank.(b) Apply light oil
around the new check valve as shown in the
illustration, and insert it into the tank without force.
Becareful not to drop the gasket into the tank.
(c) Check that the check valve is fully inserted.
29. INSTALL FUEL TANK ASSY
(a) Set the mission jack to the fuel tank.(b) Install the fuel
tank with the fuel tank bands.
Torque: 39 N ⋅m (400 kgf ⋅cm, 29 ft ⋅lbf)30. INSTALL FUEL PUMP
TUBE SUB–ASSY
(a) Push in the fuel tube connector to the fuel pipe until
con-nector makes a ”click” sound.
NOTICE:� Check if there is any damage or foreign objects on
the
connected part of the pipe.� After connecting, check if the pipe
and the connector
are securely connected by pulling them.
31. INSTALL FUEL TANK PROTECTOR LOWER CENTER
(a) Install the protector with the 4 bolts.Torque: 5.4 N ⋅m (55
kgf ⋅cm, 48 in. ⋅lbf)
32. INSTALL PARKING BRAKE CABLE ASSY NO.3
Torque: 5.4 N ⋅m (55 kgf ⋅cm, 48 in. ⋅lbf)33. INSTALL PARKING
BRAKE CABLE ASSY NO.2
Torque: 5.4 N ⋅m (55 kgf ⋅cm, 48 in. ⋅lbf)34. INSTALL EXHAUST
PIPE ASSY CENTER
(See page 15–2)35. INSTALL FLOOR PANEL BRACE REAR
(See page 15–2)36. INSTALL FUEL SUCTION TUBE ASSY W/ PUMP &
GAGE (See page 11–15)37. INSTALL FUEL TANK VENT TUBE SET PLATE
(See page 11–15)38. INSTALL FUEL PUMP TUBE SUB–ASSY
(See page 11–15)39. INSTALL REAR FLOOR SERVICE HOLE COVER
(See page 11–15)40. INSPECT FUEL LEAK41. CHECK EXHAUST
LEAKAGE
-
1109E–01
A62391
C/OPN Relay
B00679
11–26–FUEL FUEL SYSTEM (1MZ–FE)
1470Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
FUEL SYSTEM (1MZ–FE)PRECAUTION1. PRECAUTION(a) Before working on
fuel system, disconnect negative (–) terminal cable from
battery.(b) Do not smoke or work near an open flame when working on
fuel system.(c) Keep gasoline away from rubber or leather
parts.
2. WORK FOR PREVENT GASOLINE FROM SPILLINGOUT
CAUTION:� Perform disconnecting operation of the fuel system
parts after working for prevent gasoline form spillingout.
� As there is remained pressure in the fuel line afterworking
for prevent gasoline from spilling out, pre-vent it from splashing
inside the vehicle compart-ment by covering them with a shop
rag.
(a) Remove the circuit opening relay in the engine room
relayblock.
(b) Start the engine. After the engine has stopped on its
own,turn the ignition switch OFF.
HINT:There is a case that DTC P0171 (system to lean) is
output.(c) Check that the engine does not start.(d) Remove the fuel
tank cap, and let the air out of the fuel
tank.(e) Disconnect negative (–) terminal cable from battery.(f)
Reinstall the circuit opening relay.3. FUEL SYSTEM(a) When
disconnecting the high fuel pressure line, a large
amount of gasoline will spill out, so observe these
proce-dures.(1) Work for prevent gasoline from spilling out.(2)
Disconnect the fuel pump tube.
(See page 11–39)(3) Drain the fuel remained inside the fuel pump
tube.
(4) Prevent the disconnected fuel pump tube fromdamaging and
mixing foreign objects by coveringthem with a vinyl bag.
-
B00347
New O–ring
Delivery Pipe
Injector
CORRECT
WRONG
Grommet
FI6372
A62371
Delivery Pipe
Spacer
Insulator
O–ring
Grommet
A60083
Fuel Pipe Clamp No.1
A
A
B12941
–FUEL FUEL SYSTEM (1MZ–FE)11–27
1471Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
(5) Put a container under the connection.
(b) Observe these precautions when removing and installingthe
injector.(1) Never reuse the O–ring.(2) When placing the new
O–rings on the injector, take
care not to damage it in any way.(3) Coat a new O–rings with
spindle oil or gasoline be-
fore installing. Never use engine, gear or brake oil.
(c) Install the injector to the delivery pipe and intake
manifold,as shown in the illustration. Before installing the
injector,be sure to apply spindle oil or gasoline on the place
wherea delivery pipe or an intake manifold touches an O–ringof the
injector.
(d) Observe these precautions when disconnecting the fueltube
connector.(1) Remove the fuel pipe clamp No.1.(2) Check if there is
any dirt like mud on the pipe and
around the connector before disconnecting themand clean the dirt
away.
(3) Disconnect the connector from the hose whilepinching part A
with fingers as shown in the illustra-tion.
-
B12944
Vinyl Bag
A52581
11–28–FUEL FUEL SYSTEM (1MZ–FE)
1472Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
(4) When the connector and the pipe are stuck, pinchthe fuel
pipe between the hands, push and pull theconnector to free to
disconnect and pull it out. Donot use any tool at this time.
(5) Inspect if there is any dirt or the likes on the seal
sur-face of the disconnected pipe and clean it away.
(6) Prevent the disconnected pipe and connector fromdamaging and
mixing foreign objects by coveringthem with a vinyl bag.
4. CHECK FUEL LEAK(a) Check that there are no fuel leaks after
doing maintenance anywhere on the fuel system.
(See page 11–29)
-
11027–02
Fuel Tube Connector
A50710
A60083
Fuel Pipe Clamp No.1
A
A
B12941
–FUEL FUEL SYSTEM (1MZ–FE)11–29
1473Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
ON–VEHICLE INSPECTION
1. CHECK FUEL PRESSURE(a) Prepare for inspection.
(1) Purchase the new No.1 fuel pipe and take out thefuel tube
connector from its pipe.
HINT:Part No. 23801–20140(b) Work for prevent gasoline from
spilling out.
(See page 11–26)
(c) Remove the fuel pipe clamp No.1 from the fuel tube
con-nector.
(d) Disconnect the fuel tube connector from the fuel pipewhile
pinching part A with fingers as shown in the illustra-tion.
CAUTION:� Perform disconnecting operations of the fuel tube
connector (quick type) after observing the precau-tions.
� As there is retained pressure in the fuel pipe line, pre-vent
it from splashing inside the engine compart-ment.
-
No.1 Fuel Pipe
Fuel Tube Connector
SST(Clip)
SST (T joint)SST
SST(Hose)
B12975
11–30–FUEL FUEL SYSTEM (1MZ–FE)
1474Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
(e) Install SST (pressure gauge) as shown in the illustrationby
using SST and fuel tube connector.SST 09268–41047 (95336–08070),
09268–45014
(09268–41250)(f) Wipe off any splattered gasoline.(g) Reconnect
the negative (–) terminal cable to the battery.(h) Connect the
hand–hand tester to the DLC3.(i) Measure the fuel pressure
regulator.
Fuel pressure:304 – 343 kPa (3.1 – 3.5 kgf/cm 2, 44 – 50
psi)
If pressure is high, replace the fuel pressure regulator.If
pressure is low, check the fuel hoses and connections, fuelpump,
fuel filter and fuel pressure regulator.(j) Disconnect the
hand–held tester from the DLC3.(k) Start the engine.(l) Measure the
fuel pressure at idle.
Fuel pressure:304 – 343 kPa (3.1 – 3.5 kgf/cm 2, 44 – 50
psi)
(m) Stop the engine.(n) Check that the fuel pressure remains as
specified for 5
minutes after the engine has stopped.Fuel pressure:147 kPa (1.5
kgf/cm 2, 21 psi) or more
If pressure is not as specified, check the fuel pump,
pressureregulator and/or injectors.(o) After checking fuel
pressure, disconnect the negative (–)
terminal cable from the battery and carefully remove theSST and
fuel tube connector to prevent gasoline fromsplashing.
(p) Reconnect the No. 1 fuel pipe (fuel tube
connector).CAUTION:Perform connecting operations of the fuel tube
connector(quick type) after observing the precautions.2. CHECK FUEL
PUMP OPERATION AND FUEL LEAK(a) When using hand–held tester
(1) Connect the hand–held tester to the DLC3.(2) Turn the
ignition switch ON and hand–held tester
main switch ON.NOTICE:Do not start the engine.
(3) Select the active test mode on the hand–held tester.(4)
Please refer to the hand–held tester operator’s
manual for further details.
-
A62390
FP+B
–FUEL FUEL SYSTEM (1MZ–FE)11–31
1475Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
(b) When not using hand–held tester(1) Remove the circuit
opening relay.(2) Using a service wire connect terminals FP and
+B
of the relay block.NOTICE:Pay due attention to the terminal
connecting position toavoid a malfunction.
(3) Turn the ignition switch ON, and check that the fuelpump
operates.
NOTICE:Do not start the engine.(c) Check that there are no fuel
leaks after doing mainte-
nance anywhere on the fuel system.
-
11028–02
Fuel Tube Connector
A50710
Fuel Tube Connector
SST(Hose)
B12947
SST(Hose)
SST(Clamp)
Vinyl Tube
O–Ring
SST(Union)
A51873
11–32–FUEL FUEL SYSTEM (1MZ–FE)
1476Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
INSPECTION1. FUEL INJECTOR ASSY
(a) Inspect injector resistance(1) Using an ohmmeter, measure
the resistance be-
tween the terminals.Resistance:13.4 – 14.2 Ω at 20�C (68�F)
If the resistance is not as specified, replace the injector.(b)
Inspect injector inspectionCAUTION:Keep injector clear of sparks
during the test.
(1) Purchase the new No.1 fuel pipe and take out thefuel tube
connector from its pipe.
HINT:Part No. 23801 – 20140
(2) Connect SST and fuel tube connector to the fuelpipe.
SST 09268–41047 (95336–08070)CAUTION:Perform connecting
operations of the fuel tube connector(quick type) after observing
the precautions.
(3) Install the grommet and O–ring to the injector.(4) Connect
SST (union and hose) to the injector, and
hold the injector and union with SST (clamp)SST 09268–41047
(09268–41110, 09268–41300,
95336–08070)(5) Put the injector into a graduated cylinder.
HINT:Install a suitable vinyl tube onto the injector to prevent
gasolinefrom splashing out.
(6) Operate the fuel pump.(See Page 11–29)
-
SST
A52609
B05331
A16628 A32859
–FUEL FUEL SYSTEM (1MZ–FE)11–33
1477Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
(7) Connect SST (wire) to the injector and battery for
15seconds, and measure the injection volume with agraduated
cylinder. Test each injector 2 or 3 time.
SST 09842–30070Injection volume:
Injection volume Difference between each injector
60 – 73 cm3 (3.7 – 4.5 cu in.)per 15 seconds
13 cm3 (0.8 cu in.) or less
NOTICE:Always do the switching at the battery side.If the
injection volume is not as specified,replace the injector.
(c) Inspect leakage(1) In the condition above, disconnect the
test probes
of SST (wire) from the battery and check the fuelleakage from
the injector.
Fuel drop: 1 drop or less per 12 minutes
2. FUEL PUMP
(a) Inspect fuel pump resistance.(1) Using an ohmmeter, measure
the resistance be-
tween terminals.Resistance: 0.2 – 3.0 Ω at 20�C (68�F)
(b) Inspect fuel pump operation(1) Apply battery voltage to both
terminals. Check that
the pump operates.NOTICE:� These tests must be done quickly
(within 10 seconds)
to prevent the coil from burning out.� Keep fuel pump as far
away from the battery as pos-
sible.� Always do the switching at the battery side.
-
1109F–01
A60464
EGR Pipe No.2
�Gasket
Surge Tank Stay No.1
Engine Hanger No.1Intake Air Surge Tank
�Air Surge Tank To Intake Manifold Gasket
Fuel Delivery Pipe Sub–assySpacer No.1
Fuel Delivery Pipe No.2 �O–Ring�Grommet
Fuel Injector Assy
�Injector Vibration Insulator
Fuel Pressure Pulsation Damper Assy
Union Bolt
� Non–reusable part
N·m (kgf·cm, ft·lbf) : Specified torque
�Gasket
�Gasket
�Gasket
39 (398, 29)
43 (438, 32)
43 (438, 32)
43 (438, 32)
20 (199, 14) 12 (120, 9)
20 (199, 14)
33 (336, 24)
33 (336, 24)
10 (102, 7)
11–34–FUEL FUEL INJECTOR ASSY (1MZ–FE)
1478Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
FUEL INJECTOR ASSY (1MZ–FE)COMPONENTS
-
1101Q–02
Pulsation Damper
A51983
A62372
O–ring
Grommet
Insulator
–FUEL FUEL INJECTOR ASSY (1MZ–FE)11–35
1479Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
REPLACEMENT1. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT
(See page 11–26)2. DRAIN COOLANT (See page 16–20)3. REMOVE V–BANK
COVER SUB–ASSY
(See page 14–155)4. REMOVE BATTERY5. REMOVE AIR CLEANER ASSEMBLY
WITH HOSE (See page 10–12)6. REMOVE FRONT SUSPENSION UPPER BRACE
CENTER
(W/ FRONT SUSPENSION BRACE UPPER CENTER)
7. REMOVE INTAKE AIR SURGE TANK (See page 14–142)
8. SEPARATE FUEL PIPE SUB–ASSY NO.1
(a) Remove the pulsation damper and 2 gaskets.(b) Remove the
bolt and 2 gaskets.(c) Remove the bolt and disconnect the fuel pipe
sub–as-
sembly No. 1 from the intake manifold.
9. REMOVE FUEL INJECTOR ASSY
(a) Disconnect the injector connectors.(b) Remove the 2 bolts
and fuel delivery pipe, while pulling out both ends of the fuel
delivery pipe equally.(c) While turning the injector clockwise and
counterclockwise, pull out the injector from the delivery pipe.
10. INSTALL FUEL INJECTOR ASSY
(a) Apply a light coat of gasoline to a new O–ring and
installthem to each injectors.
(b) While turning the injector clockwise and counterclock-wise,
install it to the delivery pipe.
(c) Check that the injectors rotate smoothly.NOTICE:If injectors
do not rotate smoothly, the probable cause is in-correct
installation of the O–rings. Replace new O–rings.(d) Install the
delivery pipe with the injectors.
Torque: 10 N ⋅m (102 kgf ⋅cm, 7 ft ⋅lbf)NOTICE:� Be careful not
to drop the injectors when installing
the delivery pipe.� Check that the injectors rotate smoothly
after instal-
ling the delivery pipe.
-
Pulsation Damper
A51983
11–36–FUEL FUEL INJECTOR ASSY (1MZ–FE)
1480Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
11. INSTALL FUEL PIPE SUB–ASSY NO.1
(a) Install the fuel pipe No. 1 with the 2 new pulsation
dampergaskets and the pulsation damper.Torque: 33 N ⋅m (336 kgf
⋅cm, 24 ft ⋅lbf)
(b) Install the delivery pipe with 2 new fuel pipe No. 1
gasketsand a bolt to the fuel pipe No. 1.Torque: 33 N ⋅m (336 kgf
⋅cm, 24 ft ⋅lbf)
(c) Install the fuel pipe No. 1 to the intake manifold with a
bolt.Torque: 20 N ⋅m (199 kgf ⋅cm, 14 ft ⋅lbf)
12. INSTALL INTAKE AIR SURGE TANK (See page 14–142)
13. INSTALL FRONT SUSPENSION UPPER BRACE CENTER(W/ FRONT
SUSPENSION BRACE UPPER CENTER)
Torque: 80 N ⋅m (816 kgf ⋅cm, 59 ft ⋅lbf)14. INSTALL AIR CLEANER
ASSEMBLY WITH HOSE (See page 10–12)15. INSTALL V–BANK COVER
SUB–ASSY
(See page 14–155)16. ADD COOLANT (See page 16–20)17. CHECK
ENGINE COOLANT LEAK (See page 16–20)18. INSPECT FUEL LEAK
-
1109G–01
A57122
Rear Seat Cushion Pad
Rear Floor Service Hole Cover
Fuel Tank Vent Tube Set Plate
Fuel Suction Tube Assy W/Pump & Gage
Fuel Pump Tube Sub–assy
� Non–reusable part
N·m (kgf·cm, ft·lbf) : Specified torque
�Fuel Suction Tube Set Gasket
3.5 (36, 31 in. ⋅lbf)
–FUEL FUEL PUMP ASSY (1MZ–FE)11–37
1481Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
FUEL PUMP ASSY (1MZ–FE)COMPONENTS
-
A57123� Non–reusable part
Fuel Pump Harness
Fuel Sender Gage Assy
Fuel Suction Plate Sub–assy
Fuel Pump
Fuel Filter Assy
Fuel Pump Filter
Fuel Suction Support No.2
Fuel Pressure Regulator Assy
�O–ring
Cushion Rubber
�Clip
11–38–FUEL FUEL PUMP ASSY (1MZ–FE)
1482Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
-
1109H–01
A52585
O–ring
Fuel Pump Tube
ClipO–ring
Fuel Suction Plate
Fuel Tube Joint
A52589
A52586
–FUEL FUEL PUMP ASSY (1MZ–FE)11–39
1483Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
Removal & Installation and Disassembly & Reassembly1.
REMOVE REAR SEAT CUSHION PAD
2. REMOVE REAR FLOOR SERVICE HOLE COVER
(a) Remove the service hole cover.(b) Disconnect the fuel pump
connector.3. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT (See
page 11–26)
4. DISCONNECT FUEL PUMP TUBE SUB–ASSY
(a) Check if there is any dirt like mud around the
connectorbefore this work and clean dirt away.
(b) Remove the joint clip, and pull out the fuel pump
tube.NOTICE:� Be careful of dirt like mud because the quick
connec-
tor has an O–ring to seal the pipe and the connector.� Do not
use any tool in this work.� Do not bend or twist the nylon tube by
force.� Keep off plug from foreign objects.� To protect the fuel
tube, cover it with a vinyl bag after
checking.
5. REMOVE FUEL TANK VENT TUBE SET PLATE
(a) Remove the 8 bolts and fuel tank vent tube set plate.
6. REMOVE FUEL SUCTION TUBE ASSY W/ PUMP & GAGE(a) Pull out
the fuel suction tube w/pump & gage from the fuel tank.NOTICE:�
Do not damage the fuel pump filter.� Be careful that the arm of the
sender gauge should not bent.
(b) Remove the fuel suction tube gasket.7. REMOVE FUEL SUCTION
SUPPORT NO.2
(a) Using a screwdriver, disconnect the snap claws from the claw
holes and remove the fuel suction sup-port No.2.
-
A52586
11–40–FUEL FUEL PUMP ASSY (1MZ–FE)
1484Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
8. REMOVE FUEL PUMP CUSHION RUBBER
9. REMOVE FUEL PRESSURE REGULATOR ASSY
10. REMOVE FUEL PUMP ASSY W/FILTER(a) Disconnect the fuel pump
connector from the fuel pump.(b) Pull out the fuel filter and the
fuel pump assembly.11. REMOVE FUEL PUMP FILTER
(a) Using a screwdriver, remove the fuel pump filter clip and
the fuel pump filter.12. REMOVE FUEL SUCTION PLATE SUB–ASSY
(a) Using a screwdriver, disconnect the snap claws from the claw
holes and remove the fuel suction plate.13. REMOVE FUEL SENDER GAGE
ASSY
(a) Unlock the sender gage, and move it downward to remove.14.
REMOVE FUEL PUMP HARNESS
(a) Disconnect the connector, and remove the fuel pump
harness.15. INSTALL FUEL SENDER GAGE ASSY
(a) Lock the sender gage by pushing it upward.NOTICE:By pushing
the sender gage downward, confirm that it is certainly locked.16.
INSTALL FUEL PUMP FILTER
(a) Install the fuel pump filter with a new fuel pump filter
clip.17. INSTALL FUEL PRESSURE REGULATOR ASSY
(a) Apply gasoline to a new O–ring, and install it to the
pressure regulator.(b) Insert the pressure regulator.18. INSTALL
FUEL SUCTION TUBE ASSY W/ PUMP & GAGE(a) Install a new gasket
and fuel suction tube w/pump & gage.
19. INSTALL FUEL TANK VENT TUBE SET PLATE
(a) Install the fuel tank vent tube set plate with the 8
bolts.Torque: 3.5 N ⋅m (36 kgf ⋅cm, 31 in. ⋅lbf)
-
A57126
–FUEL FUEL PUMP ASSY (1MZ–FE)11–41
1485Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
20. INSTALL FUEL PUMP TUBE SUB–ASSY
(a) Connect the main tube with the tube joint clip.NOTICE:�
Check that there is no scratch or foreign objects on
the connecting part.� Check that the connector is inserted fully
and secure-
ly.� Check that the clip of the tube joint is on the collar
of
the connector.� After installing the clip of the tube joint,
check that the
connector is not pulled off.21. INSTALL REAR FLOOR SERVICE HOLE
COVER
(a) Using a new butyl tape set, and install the rear floor
service hole cover.22. INSPECT FUEL LEAK
-
1109I–01
A57122
Rear Seat Cushion Pad
Rear Floor Service Hole Cover
Fuel Tank Vent Tube Set Plate
Fuel Suction Tube Assy W/Pump & Gage
Fuel Pump Tube Sub–assy
� Non–reusable part
N·m (kgf·cm, ft·lbf) : Specified torque
�Fuel Suction Tube Set Gasket
3.5 (36, 31 in. ⋅lbf)
11–42–FUEL FUEL TANK ASSY (1MZ–FE)
1486Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
FUEL TANK ASSY (1MZ–FE)COMPONENTS
-
A57124
Pin
Parking Brake Cable Assy No.2
Fuel Tank ProtectorLower Center
Fuel Tank Band Sub–assy No.1 RH
Exhaust Center Pipe Assy
Floor Panel Brace Rear
�Exhaust Pipe Gasket
Fuel Tank Band Sub–assy No.1 LH
Parking Brake Cable Assy No.3
� Non–reusable part
N·m (kgf·cm, ft·lbf) : Specified torque
�Exhaust Pipe Gasket
39 (400, 29)
39 (400, 29)
5.4 (55, 48 in. ⋅lbf)
5.4 (55, 48 in. ⋅lbf)
56 (571, 41)
20 (199, 14 )56 (571, 41)
�
�
5.4 (55, 48 in. ⋅lbf)
–FUEL FUEL TANK ASSY (1MZ–FE)11–43
1487Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
-
A57125� Non–reusable part
N·m (kgf·cm, ft·lbf) : Specified torque
Charcoal Canister Assy
Fuel Tank Protector No.3
Fuel Cut Off Valve Assy w /Tube
Fuel Tank Over Fill Check Valve Assy
Location of Fuel Tank Cushion
Fuel Tank Inlet Pipe Sub–assy
Fuel Pump Tube Sub–assy
Fuel Main Tube Support
�Check Valve Gasket
�Fuel Tank Breather Tube Gasket
Fuel Tank Protector Sub–assy No.1
5.4 (55, 48 in. ⋅lbf)
11–44–FUEL FUEL TANK ASSY (1MZ–FE)
1488Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
-
1109J–01
A57127
A57128
–FUEL FUEL TANK ASSY (1MZ–FE)11–45
1489Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
Removal & Installation and Disassembly & Reassembly1.
REMOVE REAR SEAT CUSHION PAD
2. REMOVE REAR FLOOR SERVICE HOLE COVER (See page 11–39)
3. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT (See page
11–26)4. DISCONNECT FUEL PUMP TUBE SUB–ASSY
(See page 11–39)5. REMOVE FUEL TANK VENT TUBE SET PLATE
(See page 11–39)6. REMOVE FUEL SUCTION TUBE ASSY W/ PUMP &
GAGE (See page 11–39)7. DRAIN FUEL8. REMOVE FLOOR PANEL BRACE
REAR
(See page 15–5)9. REMOVE EXHAUST PIPE ASSY CENTER
10. DISCONNECT PARKING BRAKE CABLE ASSY NO.2
(a) Remove the bolt and nut, and disconnect the parkingbrake
cable.
11. DISCONNECT PARKING BRAKE CABLE ASSY NO.3
(a) Remove the bolt and nut, and disconnect the parkingbrake
cable.
12. REMOVE FUEL TANK PROTECTOR LOWER CENTER
(a) Remove the 4 bolts and remove the protector.
-
A57129
A57130
B01253
Push
Pinch
Pinch
AA
11–46–FUEL FUEL TANK ASSY (1MZ–FE)
1490Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
13. DISCONNECT FUEL PUMP TUBE SUB–ASSY
(a) Pinch the fuel pump tube connector clip and then pull outthe
tube.
NOTICE:� Check if there is any dirt like mud around the
connec-
tor before this work and clean the dirt away.� Be careful of
dirt like mud because the quick connec-
tor has an O–ring to seal the pipe and the connector.� Do not
use any tool in this work.� Do not bend or twist the nylon tube by
force.� After disconnecting the tube, cover the connector
with a vinyl bag.� When the connector and the pipe are stuck,
pinch the
tube between fingers, and turn it carefully to free andthen
disconnect the tube.
14. DISCONNECT FUEL TANK TO FILLER PIPE HOSE
(a) Disconnect the fuel tack to filler pipe hose from the fuel
tank.15. DISCONNECT FUEL TANK BREATHER HOSE
(a) Disconnect the fuel tank breather hose from the fuel
tank.16. REMOVE FUEL TANK ASSY
(a) Set the mission jack to the fuel tank.(b) Remove the fuel
tank bands.(c) Disconnect the valve to fuel filler pipe hose from
the fuel
tank over fill check valve.(d) Disconnect the fuel hose No. 3
from the fuel tank.
(e) Disconnect the vent line hose from the charcoal canister.(1)
Push the connector deep inside.(2) Pinch portion A.(3) Pull out the
connector.
(f) Disconnect the fuel emission hose from the charcoal
can-ister.
(g) Carefully, remove the fuel tank assembly from the
vehicle.
-
A57334
Clip Remover
A57335
A57336
A57337
–FUEL FUEL TANK ASSY (1MZ–FE)11–47
1491Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
17. REMOVE FUEL TANK OVER FILL CHECK VALVEASSY
(a) Using a screwdriver, unlock the claw and remove the
pro-tector by turning it counter clockwise.
(b) Insert a clip remover between the check valve and thegasket,
remove the valve by gradually pushing it upward.
NOTICE:� Work accurately to maintain the sealing performance
of the check valve, since it is made from resin. It iseasy to
damage by removing and installing forcibly.
� Be sure to install new check valve and gasket.
18. REMOVE FUEL TANK PROTECTOR NO.3
(a) Remove the fuel tank protector No. 3 by sliding as shownin
the illustration.
19. REMOVE FUEL TANK PROTECTOR SUB–ASSY NO.1
(a) Remove the fuel tank protector No. 1 by sliding as shownin
the illustration.
-
A60493
ValveGasket
A60495
A60494
Apply light oil around the valve
11–48–FUEL FUEL TANK ASSY (1MZ–FE)
1492Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
20. REMOVE FUEL CUT OFF W/TUBE VALVE ASSY
(a) Using a screwdriver, unlock the claw and remove the
pro-tector by turning it counter clockwise.
(b) Insert a clip remover between the cut off valve and
thegasket, remove the cut off valve by gradually pushing
itupward.
NOTICE:� Work accurately to maintain the sealing performance
of the cut off valve, since it is made from resin. It iseasy to
damage by removing and installing forcibly.
� Be sure to install new cut off valve and gasket.21. REMOVE
FUEL MAIN TUBE SUPPORT
22. REMOVE FUEL TANK CUSHION NO.1
23. REMOVE FUEL TANK CUSHION NO.2
24. INSTALL FUEL TANK CUSHION NO.1
(a) Install new fuel tank cushions as shown in the
illustration.25. INSTALL FUEL TANK CUSHION NO.2
(a) Install new fuel tank cushions as shown in the
illustration.
26. INSTALL FUEL MAIN TUBE SUPPORT
Torque: 5.4 N ⋅m (55 kgf ⋅cm, 48 in. ⋅lbf)
27. INSTALL FUEL CUT OFF W/TUBE VALVE ASSY
(a) Install a new gasket to the fuel tank.(b) Apply light oil
around the new fuel cut off valve as shown
in the illustration, and insert it into the tank without
force.Be careful not to drop the gasket into the tank.
(c) Check that the fuel cut off valve is fully inserted.
-
A60496
Apply light oil around the valve
A57340
–FUEL FUEL TANK ASSY (1MZ–FE)11–49
1493Author�: Date�:
2002 CAMRY REPAIR MANUAL (RM881U)
28. INSTALL FUEL TANK OVER FILL CHECK VALVEASSY
(a) Install a new gasket to the fuel tank.(b) Apply light oil
around the new check valve as shown in the
illustration, and insert it into the tank without force.
Becareful not to drop the gasket into the tank.
(c) Check that the check valve is fully inserted.
29. INSTALL FUEL TANK ASSY
(a) Set the mission jack to the fuel tank.(b) Install the fuel
tank with the fuel tank bands.
Torque: 39 N ⋅m (400 kgf ⋅cm, 29 ft ⋅lbf)30. INSTALL FUEL PUMP
TUBE SUB–ASSY
(a) Push in the fuel tube connector to the fuel pipe until
con-nector makes a ”click” sound.
NOTICE:� Check if there is any damage or foreign objects on
the
connected part of the pipe.� After connecting, check if the pipe
and the connector
are securely connected by pulling them.
31. INSTALL FUEL TANK PROTECTOR LOWER CENTER
(a) Install the protector with the 4 bolts.Torque: 5.4 N ⋅m (55
kgf ⋅cm, 48 in. ⋅lbf)
32. INSTALL PARKING BRAKE CABLE ASSY NO.3
Torque: 5.4 N ⋅m (55 kgf ⋅cm, 48 in. ⋅lbf)33. INSTALL PARKING
BRAKE CABLE ASSY NO.2
Torque: 5.4 N ⋅m (55 kgf ⋅cm, 48 in. ⋅lbf)34. INSTALL EXHAUST
PIPE ASSY CENTER
(See page 15–5)35. INSTALL FLOOR PANEL BRACE REAR
(See page 15–5)36. INSTALL FUEL SUCTION TUBE ASSY W/ PUMP &
GAGE (See page 11–39)37. INSTALL FUEL TANK VENT TUBE SET PLATE
(See page 11–39)38. INSTALL FUEL PUMP TUBE SUB–ASSY
(See page 11–39)39. INSTALL REAR FLOOR SERVICE HOLE COVER
(See page 11–39)40. INSPECT FUEL LEAK41. CHECK EXHAUST
LEAKAGE