FTI-GMK2 Type 1B2 - Vehicle Coverage & Preparation Notes Make Model Year Install I/O Changes DL-GM7 Chevrolet Colorado Key w/o On-Star 2017-19 Type 1 CAN Lights RAP Trunk Green White/Blue Park / Auto BCM H CM-900 CM-900S/900AS CM7X00 CM7000/7200 Cut loop for A/T CM900AS/900S Jumper SUPPORT - 1(888) 820-3690, EXT. 203 DEREK ZOOLANDER Est. 2001 CENTER KIDS WHO CAN’T READ GOOD AND W H O W ANNA LEAR N T O D O O T H E R S T U F F G O O D T O O IIIIIIIII IIIIIIIIIIIIIIIIIIIIIII I I I I I I I I I I IIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIII for Hey! Read this stuff before you start the installation... Firmware: Covered vehicles use BLADE-AL(DL)-GM12, flash module and update the controller firmware before installing. Install: Type 1 vehicles attain CAN data from the vehicle BCM, which requires the CAN/BCM configuration of the CAN source junction on the harness assembly. The vehicle BCM is located left of the steering column (LSC) in all covered vehicles . Lights: Type H lights are incorporated in the harness and utilize the vehicle hazard lights for visual display of runtime status/diagnostics. Re-pinning of the CM I/O (gray) harness is required if you wish to use hazard lights, traditional parking light option is noted in the installation notes and diagram. Use of hazards also requires that you reconfigure the POC for one of the following hazard control options, Hazard1 (POC option #30 (momentary) or Hazard2 (POC option #23 (latching), depending on hazard switch operation. Locks: CM lock connector is mandatory for this installation type. The harness is pre-wired in the harness assembly to provide the necessary analog control
2
Embed
FTI-GMK2 Type 1B2 - Vehicle Coverage & Preparation Notes · 2019-09-13 · FTI-GMK2 Type 1B2 - Vehicle Coverage & Preparation Notes Make Model Year Install I/O Changes DL-GM7 Chevrolet
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
FTI-GMK2 Type 1B2 - Vehicle Coverage & Preparation Notes
Hey! Read this stuff before you start the installation...
Firmware:Covered vehicles use BLADE-AL(DL)-GM12, flash module and update the controller firmware before installing.
Install:Type 1 vehicles attain CAN data from the vehicle BCM, which requires the CAN/BCM configuration of the CAN source junctionon the harness assembly. The vehicle BCM is located left of the steering column (LSC) in all covered vehicles .
Lights:Type H lights are incorporated in the harness and utilize the vehicle hazard lights for visual display of runtime status/diagnostics.Re-pinning of the CM I/O (gray) harness is required if you wish to use hazard lights, traditional parking light option is noted in theinstallation notes and diagram. Use of hazards also requires that you reconfigure the POC for one of the following hazard controloptions, Hazard1 (POC option #30 (momentary) or Hazard2 (POC option #23 (latching), depending on hazard switch operation.
Locks:CM lock connector is mandatory for this installation type. The harness is pre-wired in the harnessassembly to provide the necessary analog control
Green Connector
Blue Connectors
Pink Connector
A B C D E
A
B
C
LED Programming Error CodesModule LED flashing RED during programming
1
2
SUPPORT - 1(888) 820-3690, EXT. 203
FTI-GMK2 Type 1B2
Module Programming Procedure
FTI-GMK2 Type 1B2 - Installation Notes & Wiring Diagram
A
B
PWRBLADE Lock
GREEN
BLUE
WHITE
14
21
1 2
8
5 6 7
2015
25
15
16
22
1 2 3 4
5 8
9
27
21
23 24
14
15
21 22
1 2 3 4
5 7
8
26
20
16
64
14
A
OBD-II Connector
BCM
C
B
1
19
15
C
1
2
Hazard light connection, pin terminated, replace the wire for POC 1 in the CMx I/O connector if hazardflash is desired. See also, note [D]
CAN/SWC source selector, Type 1 installs require CAN/BCM configuration, as illustrated. Secure theunused OBD connector for safety.
Harness is wired for runtime/diagnostic lighting via hazard lights, if traditional pk lights are desired useCM I/O ( - ) pk light output (green/white) connected to lt. green/gray in pin #22 of white X1 connector
C
PK
LIG
HTS
( - )
1x - No ACC power, check GREEN connector2x - MUX status not detected, check GREEN connector3x - No IGN, check GREEN connector4x - No HSCAN activity, check BLUE connector5x - No SWC activity, check BLUE connector6x - Wrong SWC message, confirm key has been removed7x - No ACC power, check GREEN connector8x - No immobilizer data, check GREEN & BLADE connectors9x - IGN ON, confirm key has been removed10x - Keysense active, confirm key has been removed11x - No ACC, confirm key is on12x - No IGN, confirm key is on13x - VIN not matching Weblink data, contact engineering
Step 1 - Wake vehicle network by opening and closing driver doorStep 2 - Insert Key, activate IGN, wait for module LED to go solid redStep 3 - Remove key from cylinder, LED will go offStep 4 - Reinsert key, activate IGN, wait for rapid blue flashStep 5 - Remove key, return to computer for extended programmingStep 6 - Reconnect, wake network, activate IGN, LED goes solid blueStep 7 - Programming complete
D CM lock connector mandatory for this installation type, locks are handled by analog connections tothe BCM, pre-wired in the harness assembly