Freestanding Santa Claus - Embroidery Online...Freestanding Santa Claus Handy Hints Drying: • Freestanding pieces look best when left to dry with right side down. This will minimize

Note: Some designs in this collection may have been created using unique special stitches and/or techniques. To preserve design integrity when rescaling or rotating designs in your software, always rescale or rotate designs using the handles directly on-screen.

It is a violation of Copyright law to make and distribute copies of electronic designs or artwork. Electronic designs are licensed to the original purchaser for use at one location. ©2017 OESD, LLC. All rights reserved.

Freestanding Santa Claus#12702 / 16 Files / 1 Design

12702-01 Santa Robe Slice 1 FSA3.45 X 8.02 in.

87.63 X 203.71 mm46,974 St.


87.63 X 203.71 mm37,674 St.


87.63 X 203.71 mm37,453 St.


87.63 X 203.96 mm34,461 St.

12702-05 Santa Arm 1 FSA3.03 X 4.45 in.

76.96 X 113.03 mm17,311 St.

12702-06 Santa Arm 2 FSA3.03 X 4.45 in.

76.96 X 113.03 mm17,325 St.

12702-07 Santa Cape FSA4.54 X 8.26 in.

115.32 X 209.80 mm54,510 St.

12702-08 Santa Foundation FSA5.72 X 5.42 in.

145.29 X 137.67 mm16,568 St.

12702-09 Santa Beard FSL4.04 X 4.00 in.

102.62 X 101.60 mm22,294 St.

12702-10 Santa Face FSA1.90 X 4.30 in.

48.26 X 109.22 mm5,484 St.

12702-11 Santa Hair & Face 1 FSA

1.89 X 4.32 in.48.01 X 109.73 mm

9,335 St.

12702-12 Santa Hair & Face 2 FSA

1.92 X 4.30 in.48.77 X 109.22 mm

9,337 St.

Note: Some designs in this collection may have been created using unique special stitches and/or techniques. To preserve design integrity when rescaling or rotating designs in your software, always rescale or rotate designs using the handles directly on-screen.



12702-13 Santa Hair FSL1.91 X 4.35 in.

48.51 X 110.49 mm10,900 St.

12702-14 Santa Hat FSA5.22 X 6.01 in.

132.59 X 152.65 mm23,760 St.

12702-15 Santa Hat Ring FSL1.16 X 9.95 in.

29.46 X 252.73 mm32,093 St.

12702-16 Santa Hat Ball FSL0.96 X 1.21 in.

24.38 X 30.73 mm1,956 St.

Listings below indicate color sample, stitching order and suggested thread color number. Most numbers indicate Isacord thread. Colors beginning with 20501 refer to YLI Fine Metallics, 7 refer to Yenmet Metallic, 8 refer to YLI Variations Variegated Thread and 9 refer to Isacord Multicolor Variegated.



12702-01 Santa Robe Slice 1 FSAn 1. Robe Slice 1 Placement Stitch ................................... 0015n 2. Cut Line & Tackdown ................................................. 0015n 3. White Lace ................................................................. 0015n 4. Damask Detail ............................................................ 1912n 5. Red Lace & Cover Stitch ............................................ 2101




12702-05 Santa Arm 1 FSAn 1. Arm 1 Placement Stitch .............................................. 0015n 2. Cut Line & Tackdown ................................................. 0015n 3. White Lace ................................................................. 0015n 4. Charcoal Lace ............................................................ 4174n 5. Damask Detail ............................................................ 1912n 6. Red Lace & Cover Stitch ............................................ 2101

12702-06 Santa Arm 2 FSAn 1. Arm 2 Placement Stitch .............................................. 0015n 2. Cut Line & Tackdown ................................................. 0015n 3. White Lace ................................................................. 0015n 4. Charcoal Lace ............................................................ 4174n 5. Damask Detail ............................................................ 1912n 6. Red Lace & Cover Stitch ............................................ 2101

12702-07 Santa Cape FSAn 1. Cape Placement Stitch ............................................... 0015n 2. Cut Line & Tackdown ................................................. 0015n 3. White Lace ................................................................. 0015n 4. Damask Detail ............................................................ 1912n 5. Red Lace & Cover Stitch ............................................ 2101

12702-08 Santa Foundation FSAn 1. Foundation Placement Stitch ..................................... 0015n 2. Cut Line & Tackdown ................................................. 0015n 3. White Detail & Cover Stitch ........................................ 0015

12702-09 Santa Beard FSLn 1. Single Color Design ................................................... 0015

12702-10 Santa Face FSAn 1. Face Placement Stitch ............................................... 0015n 2. Cut Line & Tackdown ................................................. 0015n 3. White Lace ................................................................. 0015n 4. Eyes ........................................................................... 4174n 5. Nose ........................................................................... 1430n 6. Skin Lace & Cover Stitch ........................................... 1060

12702-11 Santa Hair & Face 1 FSAn 1. Face 1 Placement Stitch ............................................ 0015n 2. Cut Line & Tackdown ................................................. 0015n 3. White Lace ................................................................. 0015n 4. Skin Lace & Cover Stitch ........................................... 1060

12702-12 Santa Hair & Face 2 FSAn 1. Face 2 Placement Stitch ............................................ 0015n 2. Cut Line & Tackdown ................................................. 0015n 3. White Lace ................................................................. 0015n 4. Skin Lace & Cover Stitch ........................................... 1060

12702-13 Santa Hair FSLn 1. Single Color Design ................................................... 0015

12702-14 Santa Hat FSAn 1. Hat Placement Stitch .................................................. 2101n 2. Cut Line & Tackdown ................................................. 2101n 3. Hat Placement Stitch .................................................. 2101n 4. Cut Line & Tackdown ................................................. 2101n 5. Stripes ........................................................................ 1912n 6. White Lace ................................................................. 0015n 7. Red Lace & Cover Stitch ............................................ 2101

12702-15 Santa Hat Ring FSLn 1. Single Color Design ................................................... 0015

12702-16 Santa Hat Ball FSLn 1. Single Color Design ................................................... 0015

Isacord Thread Colors Used in “Freestanding Santa Claus”Collection #12702

0015 White 1060 Shrimp Pink

1430 Melon 1912 Winterberry

2101 Country Red 4174 Charcoal

It is a violation of Copyright law to make and distribute copies of instructions or artwork. Electronic designs are licensed to the original purchaser for use at one location. ©2017 OESD, LLC. All rights reserved.

InstructionsFreestanding Santa Claus

Supplies:Embroidery Thread:• Usethesameembroiderythreadinthebobbinastheneedle.

Needles:• UseanOrgan80/12Titaniumneedleforextendedneedlelife.

Stabilizer:• Usewater-solublestabilizerorfilmwater-solublestabilizer.

Handy Hints:For Stiffer Lace:• DONOTrinseawayallofthestabilizerfora“stiffer”lace.Notethatthethreadmayappearashadedarkerifstabilizerisnotremovedcompletely.

• Ifyouhappentowashtoomuchout,easilyre-stiffenbydilutingsomestabilizerscrapsinwateranddippingtheiteminthesolution.

For Very Soft Lace:• Cutawayexcessstabilizer.Removeremainingstabilizerbyrinsingunderwarmrunningwateruntilalltracesofthestabilizeraregone.Note:Iflaceshouldbecometoolimptoworkwith,dissolvestabilizerscrapsinwarmwaterandapplytothelace.

Drying Lace:• Thelacelooksbestwhenlefttodrycompletely.Laylacepiecewithrightsidedowntodry.Thiswillminimizethetendencyforthelacetocurl.Besuretoflattenthepieceoutentirelyandallowampletimetodry.

General Freestanding Lace Guidelines

Diagram 1

Eyelet

Buttonette

General Instructions1.Hooptwolayersofwater-solublestabilizer.2.Attachthehooptothemachineandselectthedesignofyourchoice.

3.Stitchthedesign.4.Removethehoopfromthemachineandthedesignfromthehoop.Trimexcessstabilizerfromthedesign.

5.Rinseawayremainingstabilizerandallowittodry.

Handy Hints:For 3D Lace Projects:• Rinsingoutlacewithveryhotwatercancausewrinklesinsomefabricsafterithasbeenembroidered.Topreventthis,pre-shrinkcottonfabricbywashingitinwarmwateranddryingitinadryer.

• Ifitembecomestoolimptoworkwith,irontheappliquépiecesonthewrongsidewhileapplyingspraystarch.Afterironing,sprayagainwithstarchandallowtodrycompletely.Thiswillstiffenthelacepiecesnicelyandaidinconstruction.

• Apairoftweezers,hemostats,stilettooratinycrochethookcanbeextremelyhelpfulwheninsertingthebuttonettesintotheeyelets.(PleaseseeDiagram 1forexplanationof“buttonette”and“eyelet”.)

• Insertthetipofthetweezers,hemostatsorcrochethookintotheeyelet,graspthebuttonetteandpullthroughtheeyelet.Orastilettocouldbeusedtopushthebuttonettethroughtheeyelet.



Handy HintsDrying:• Freestanding pieces look best when left to dry with

right side down. This will minimize the tendency for a piece to curl. Be sure to flatten the piece out entirely and allow ample time to dry.

For 3D Appliqué Projects:• Adhere 1 layer of OESD StabilStick TearAway to the

back of appliqué fabrics with temporary adhesive spray BEFORE hooping or placing down for tackdown and cut in place. This gives fabric a more rigid structure.

• A pair of tweezers, hemostats, stiletto or a tiny crochet hook can be extremely helpful when inserting the buttonettes into the eyelets. (See Diagram 1 for explanation of “buttonette” and “eyelet”.)

• Insert the tip of the tweezers, hemostats or crochet hook into the eyelet, grasp the buttonette and pull through the eyelet. Or a stiletto could be used to push the buttonette through the eyelet.

Supplies:Embroidery Thread:• Use the same embroidery thread in the bobbin as the needle.

Needles:• Use an Organ 80/12 Titanium needle for extended needle life.

Stabilizer:• Use water-soluble stabilizer or film water-soluble stabilizer.

General Freestanding Appliqué Guidelines

Diagram 1 Eyelet

Buttonette

General Appliqué Instructions1. Hoop two layers of OESD AquaMesh Stabilizer.2. Attach the hoop to the machine and select the design of your

choice.3. Stitch the Placement Stitch. Photo 14. Place a piece of appliqué fabric over the Placement Stitch so

that it is completely covered.5. Stitch the Cut Line & Tackdown stitch. 6. Carefully cut away the excess appliqué fabric. Photo 27. Stitch the remainder of the design and repeat for any

remaining pieces. Photo 38. Remove the hoop from the machine and the design from the

hoop. 9. Trim excess stabilizer from the design.

10. Rinse away remaining stabilizer and allow it to dry face down to prevernt curling.

Appliqué

1 2 3



Freestanding Santa Claus – SummaryRequires 1 Santa Robe Slice 1 FSA – 12702-01Requires 1 Santa Robe Slice 2 FSA – 12702-02Requires 1 Santa Robe Slice 3 FSA – 12702-03Requires 3 Santa Robe Slice 4 FSA – 12702-04Requires 1 Santa Arm 1 FSA – 12702-05Requires 1 Santa Arm 2 FSA – 12702-06Requires 1 Santa Cape FSA -- 12702-07Requires 1 Santa Foundation FSA –12702-08Requires 1 Santa Beard FSL –12702-09Requires 1 Santa Face FSA – 12702-10Requires 1 Santa Hair & Face 1 FSA –12702-11Requires 1 Santa Hair & Face 2 FSA –12702-12Requires 3 Santa Hair FSL – 12702-13Requires 1 Santa Hat FSA – 12702-14Requires 1 Santa Hat Ring FSL – 12702-15

Basic Instructions for Building FSL Santa Claus• Assemble the Santa Bottom sections starting with Santa Robe Slice 1 FSA 12702-01 attaching the

buttonettes from Santa Robe Slice 2 FSA 12702-02 to the eyelets of Santa Rose Slice 1 FSA 12702-01 using Alligator clamps. To the left of Santa Robe Slice 1 FSA 12702-01 attach Santa Robe Slice 3 FSA 12703-03 eyelets to Santa Robe Slice 1 FSA 12702-01 buttonettes. This completes the front half of the Santa Robe. The next three Robe slices are Santa Robe Slice 4 FSA-12702-04. Assemble the buttonettes and eyelets to complete the back half. Once completed attach back half to the front half of the Santa Robe. Photos 1-3

• Attach Santa Arm 1 FSA 12702-05 buttonettes to Santa Robe Slice 2 FSA 12702-02 eyelets and repeat the process with Santa Arm 2 FSA 12702-06 buttonettes to Santa Robe Slice 3 FSA 12702-03 eyelets. Photos 4-5

• Assemble Santa Cape FSA 12702-07 buttonette to eyelet. Photo 6-7

Photo 1 Photo 2 Photo 3

Photo 4 Photo 5 Photo 6 Photo 7



• Wrap Santa Cape around upper robe pulling buttonettes from Santa Robe Slice 2 & 3 through the eyelets of Santa Cape. Photos 8-10

• Assemble Santa Face FSA 12702-10 eyelets to Santa Hair & Face 1 12702-11 buttonettes and Santa Hair & Face 2 12702-12 buttonettes to Santa Face FSA 12702-10 buttonettes. Photos 11-13

• Assemble three Santa Hair FSL 12702-13 together using buttonettes and eyelets. After assembly attach to Santa Hair & Face 1 & 2. Photos 14-15

• Attach Santa Beard FSL 12702-09 buttonettes in the sides of Santa Hair and Face 1 & 2 eyelets. Photos 16

• Assemble Santa Hat Ring FSL 12702-15 buttonettes and eyelets. Photos 17-18

• Assemble Santa Hat FSA 12702-14 buttonettes and eyelets. Then attach buttonettes from Santa Hat 12702-14 to the eyelets from the inside of Santa Hat Ring FSL 12702-15. Photos 19-21


Photo 11 Photo 12 Photo 13 Photo 14 Photo 15





• Attach Santa Hat Ball FSL 12702-16 by pulling buttonette with Alligator clamps from inside of Hat eyelet. Photo 22

• Attach Santa Head by going through the inside of Santa body pulling the tabs from the Santa Head through the slits at the top of robe. Then attach Santa Foundation FSA 12702-08 eyelets to the buttonettes on the base of the Santa Robe. Photos 23-24


Freestanding Santa Claus - Embroidery Online...Freestanding Santa Claus Handy Hints Drying: • Freestanding pieces look best when left to dry with right side down. This will minimize

Documents