Free Framing Plans 8x12 - Amazon S3Tiny House Free Framing Plans 8x12 These framing plans were not prepared by or checked by a licensed engineer and/or architect. TinyHouseDesign.com

Tiny HouseFree Framing Plans

8x12

These framing plans were not prepared by or checked by a licensed engineer and/or architect. TinyHouseDesign.com does not represent or imply itself to be a licensed engineer and/or a licensed

architect. Enjoy these free house plans but use them at your own risk.

© 2011 TinyHouseDesign.com - Simple 8x12 Shed

Cross section and overview perspectives. Roof has a 12/12 pitch.

2x4 studs

2x6 floor joists

1/2" plywoodor OSB

2x6 ridge

1/2" plywoodor OSB

2x6 rafters


Floor framing details. Building could be placed on slab, piers, or your choice of foundation.

90"

96"

141"

144"

16"

48"

48"

48"96"


Back wall detail. Notice that the plywood is cut 1 1/2" short. This leaves the top plate available for the gable sheathing. Diagram in lower left shows step in construction process on this and following pages.

89"

81 1

/2"

96"

34"

40"

86"

90 3

/4"

48"

34"

40"

48"

1 1

/2"


Right wall details. See notch details on next page.

144"

137"

81 1

/2"

86"

96"

48" 48" 48"

16"


Sheathing notching detail. Notice that the notches are 16" O.C. except at the ends of the wall. Those end notched are also deeper. The notches allow the rafters to be seated and helps seat the roof.

7 3

/4"

1 1/2"1 1/2"

6 1

/4"

13 3/4"

13 3/4"

14 1/2"

14 1/2"

16"

16"

On pages later in the plans you'll see details on making boxed eaves, which are admittedly overkill if you were to also notch the siding. Both seal the roof so doing both may be redundant.

As an option you could either skip the boxed eave, or skip the notched exterior sheathing shown on this page. If you were to skip these notches you could simply cut the plywood off at the top of the wall.


Left Wall

81 1

/2"

137"

86"

16"

34"40"

34"

40"

48"

144"

48"

96"

34"

40"

34"

40"

48" 48" 48"

16"


Front Wall

34"83"

96"

81 1

/2"

86"

27 1/2"27 1/2"

48"

34" 83"

6 1

/4"

90 3

/4"

1 1

/2"


Back Wall Gable

16"

44 1

/2"

61 7/8"

96"

46"

46"

1 1/2"

66 7/8

"

5 3

/4"

48"

7"


Front Wall Gable

48"

66 7/8

"

1 1/2"

7"

46"

5 3

/4"

44 1

/2"

46"

61 7/8"

96"


Ridge beam fits right on top of gable walls and into slots in siding/sheathing.


Roof rafters and birds mouth detail for common rafters.

4"

2 1

/2"

3 1/2"

61 7/8"

72 1/2"

2 3

/4"


Roof rafters and birds mouth detail for end rafters.

4"3 1/2"

4"

61 7/8"

72 1/2"

4 1

/4"


Roof framing detail. In the image above you can see how the end rafters are a little different than the common rafters.

16"

165"

"end" rafter

common rafter


Roof sheathing detail. An attempt is made to always have plywood ends meet on a rafter. An effort was made to reduce cutting plywood, but on a roof this small there's pretty much nothing for it.

96"

44"

28"

48"

26 5/8"

1 1/2"


Boxed side eaves and gable eave trim detail. Bottom right illustration shows why the end rafters are slightly different from the common rafters. They make a clean boxed eave.

boxed eave

gable eave trim


Roofing installed over roofing felt. This would also be a good time to apply house wrap to the walls.


Install windows and doors. House wrap not shown.


Trim installed.


Siding applied. Shingles illustrated here.


Free Framing Plans 8x12 - Amazon S3Tiny House Free Framing Plans 8x12 These framing plans were not prepared by or checked by a licensed engineer and/or architect. TinyHouseDesign.com

Documents