Frameless Glass Fence and Balustrade Fittings Spiggot ™ 2009 Enhance Your View
Glass Panel FittingsStainless Steel Clamps
www.hafele.comSB 2009 HAA
Häfele now introduces a range of glass panel fittings for framelessglass fencing. This new group of products complements thecomprehensive Häfele architectural glass product range, whicharchitects and designers have been specifying throughout the world.
This new range of glass fittings include;
• Dulplex 2205 grade stainless steel clamps• Glass to glass pivots• Wall to glass pivots• Patch locks for gates• Patch fittings• Floor springs and sealing compound• Extended spindles for floor springs
The Products The FeaturesDuplex 2205 grade stainless steel, the new alternative to 316stainless steel, is ideal for waterfront constructions and pool areas.
Duplex 2205 grade performs better than 316 stainless and offersthe following benefits;
Corrosion ResistanceHaving a superior corrosion resistance to 316, Duplex 2205 performswell in most environments where standard austentic stainless steelmay fail. 2205’s low carbon content results in a high resistance tointergranular corrosion, and higher resistance to uniform pitting,crevice corrosion and tea staining.
Stress Corrosion ResistanceAs 2205 is a duplex stainless steel, the grade is less sensitive thanaustenic stainless steel to corrosion cracking in warm chlorineenvironments. A good resistance has been shown when exposed tohydrogen sulphide in chlorine solutions.
The Facts“For very aggressive applications (eg. splashed by sea water),unwashed areas, rough surfaces or those applications where nostaining can be tolerated, higher grades or stainless steel such asDuplex 2205 are preferred” The Australian Stainless Steel Association.
Contents Page
Stainless Steel Clamps . . . . . . . . . . . . . . . . . .1 - 3
Fittings for Gates . . . . . . . . . . . . . . . . . . . . . .4 - 6
Patch Fittings for Gates . . . . . . . . . . . . . . . . .7
Floor Springs for Gates . . . . . . . . . . . . . . . . .8
Floor Spring Accessories . . . . . . . . . . . . . . . .9
Dim
ensi
ons
in m
mD
imen
sion
al d
ata
not b
indi
ng. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
www.hafele.com
Glass Panel FittingsStainless Steel Clamps
Gla
ss P
anel
Fit
ting
s
SB 2009 HAA 1
9
Stainless steel clampSquare
• Area of application: Frameless glass pool fencing• Material: Duplex 2205 grade stainless steel• For glass thickness: 10 mm, 12 mm and 15 mm• Installation: Clamp fixing with hexagon bolt
Glass cut-out
Finish Cat. No.Satin 981.45.020Polished 981.45.021
Packing: 1 piece
NoteOrder base cover separately
Base coverSquare
• Area of application: Cover for clamp base• Material: Duplex 2205 grade stainless steel
Finish Cat. No.Satin 981.45.030Polished 981.45.031
Packing: 1 piece
Ø102
45º
51
4.5R2
53
25 mmholes onbottom
25%For maximumstrength 250 mmfrom the edge ofthe glass
50% 25%For maximumstrength 250 mmfrom the edge ofthe glass
4837
M10 countersunk head screw
50
4.5 x 45º
52
20
259
50
45
125
40
24
60
50
Stainless steel clampRound
• Area of application: Frameless glass pool fencing• Material: Duplex 2205 grade stainless steel• For glass thickness: 10 mm, 12 mm and 15 mm• Installation: Clamp fixing with hexagon bolt
Glass cut-out
Finish Cat. No.Satin 981.45.000Polished 981.45.001
Packing: 1 piece
NoteOrder base cover separately
Base coverRound
• Area of application: Cover for clamp base• Material: Duplex 2205 grade stainless steel
Finish Cat. No.Satin 981.45.010Polished 981.45.011
Packing: 1 piece
Ø90
Ø50
R2
4.5
25 mmholes onbottom
25%For maximumstrength 250 mmfrom the edge ofthe glass
50% 25%For maximumstrength 250 mmfrom the edge ofthe glass
M10 recessedsocket head screw
14 14
Ø48
302.5
93
170
108
Dim
ensi
ons
in m
mD
imen
sion
al d
ata
not b
indi
ng. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
Glass Panel FittingsStainless Steel Clamps
www.hafele.com
Gla
ss P
anel
Fit
ting
s
SB 2009 HAA2
9
85
Dim
ensi
ons
in m
mD
imen
sion
al d
ata
not b
indi
ng. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
www.hafele.com
Glass Panel FittingsStainless Steel Clamps
Gla
ss P
anel
Fit
ting
s
SB 2009 HAA 3
9
Wall to glass clampSquare
• Area of application: Frameless glass fencing• Material: 316 grade stainless steel• For glass thickness: 8 mm, 10 mm and 12 mm
Finish Cat. No.Satin 981.45.310Polished 981.45.311
Packing: 1 piece
• Area of application: Fixing frameless glass fencing to timberdecks
• Material: Duplex 2205 grade stainless steel• For glass thickness: 10 mm, 12 mm and 15 mm• Installation: Clamp fixing with hexagon bolt
Finish Cat. No.Satin 981.45.040Polished 981.45.041
Packing: 1 piece
Wall to glass clampRound
Stainless steel clampSquare, extended
• Area of application: Frameless glass fencing• Material: 316 grade stainless steel• For glass thickness: 8 mm, 10 mm and 12 mm
Finish Cat. No.Satin 981.45.300Polished 981.45.301
Packing: 1 piece
2727
55
Glass
25
55
27
66.5
45
Glass
25
M10 countersunkhead screw
10-Ø13
2-M12
28
20
52
50
4.5 X 45º
39
50
60
50
35
35
35
35
50
24
225
310
444
25 mmholes onbottom
25%For maximumstrength 250 mmfrom the edge ofthe glass
50% 25%For maximumstrength 250 mmfrom the edge ofthe glass
4837
Updated 04.09
Top pivotGlass to glass
• Area of application: Pivot for StarTec top patch fitting used onframeless glass pool gates
• Material: 316 grade stainless steel• For glass thickness: 10 - 12 mm• Installation: Clamp fixing with hexagon bolt
Glass cut-out
Finish Cat. No.Satin 981.45.100Polished 981.45.101
Packing: 1 piece
Top pivotWall to glass
• Area of application: Pivot for Startec top patch fitting used onframeless glass pool gates
• Material: 316 grade stainless steel• For glass thickness: 10 - 12 mm• Installation: Bolt fixing to wall
Finish Cat. No.Satin 981.45.110Polished 981.45.111
Packing: 1 piece
44
Ø18
36
84.5
70
6
3
Ø3 hole for grease
19.9
22
Ø15
R10
60 40
M6 with countersunk head
Ø3 hole for grease
140125.5
3
74.4
55.5
19.9
22
6.45
6.45
25.4
Ø15R10
M6 with countersunk head
Dim
ensi
ons
in m
mD
imen
sion
al d
ata
not b
indi
ng. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
Glass Panel FittingsFittings for Gates
www.hafele.com
Gla
ss P
anel
Fit
ting
s
SB 2009 HAA4
9
Dim
ensi
ons
in m
mD
imen
sion
al d
ata
not b
indi
ng. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
www.hafele.com
Glass Panel FittingsFittings for Gates
Gla
ss P
anel
Fit
ting
s
SB 2009 HAA 5
9
Top pivot 90º Glass to glass
• Area of application: Pivot for StarTec top patch fitting used onframeless glass pool gates
• Material: 316 grade stainless steel• For glass thickness: 10 - 12 mm• Installation: Clamp fixing with hexagon bolt
44
Ø18
36
Glass cut-out
Packing: 1 piece
NoteLeft hand pivot image shown
Finish Handing Cat. No.Satin Left hand 981.45.120Polished Left hand 981.45.121Satin Right hand 981.45.130Polished Right hand 981.45.131
Patch lock kit
• Area of application: Magnetic lock for frameless glass gate• Material: 316 grade stainless steel• For glass thickness: 10 - 12 mm• Installation: Clamp fixing with hexagon bolt
42
Ø18
326
279
Glass cut-out
Packing: 1 set
Finish Cat. No.Satin 981.45.200Polished 981.45.201
7454 M6 12 countersunk
head screw
Ø14.95
20
73
26
70
6
20
519
12
12
12 20
10
M12 grubscrew
M6 countersunk head screw
Updated 04.09
Spring hinge and lock kitGlass to glass
• Area of application: For fully frameless and semi-framelessgates
• Material: 316 grade stainless steel• For glass thickness: 10 - 12 mm• Installation: Bolt through fixing
Glass cut-out
Packing: 1 set
Finish Cat. No.Satin 981.45.400Polished 981.45.401
Spring hinge and lock kitWall to glass
• Area of application: For fully frameless and semi-framelessgates
• Material: 316 grade stainless steel• For glass thickness: 10 - 12 mm• Installation: Bolt through fixing
Glass cut-out
Packing: 1 set
Finish Cat. No.Satin 981.45.410Polished 981.45.411
92 45 2-Ø18 2-Ø18
31
20
820
42
279 326
1170
2-Ø182-Ø18
31
92 45
2-Ø18
820
31
92 452-Ø18
42
2-Ø18
279 326
1170
2-Ø18
31
4592
Conformity mark
Dim
ensi
ons
in m
mD
imen
sion
al d
ata
not b
indi
ng. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
Glass Panel FittingsFittings for Gates
www.hafele.com
Gla
ss P
anel
Fit
ting
s
SB 2009 HAA6
9Conformitymark
Conformitymark
* Gap between Wall and Glass = 20 mm
Updated 03.09
Dim
ensi
ons
in m
mD
imen
sion
al d
ata
not b
indi
ng. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
www.hafele.com
Gla
ss P
anel
Fit
ting
s
SB 2009 HAA 7
9
A StarTec Bottom patch fitting
146
36 R80
68
37 R55
Ø20
161
31
162
51
59-66
Glass cut-outGlass cut-out
Finish Cat. No.
Satin 981.00.320Polished 981.00.321
Packing: 1 piece
• Features: In combination with top pivotAdjustable pivot point by reversing insert
• Material: Case: Diecast steelCover: 316 grade stainless steel
• Glass thickness: 10 - 12 mm• Max. door weight: 80 kg• Max. door leaf width: 1100 mm• Installation: Clamp fixing, concealed, with hexagon
socket screws
• Features: In combination with bottom pivot or floorspring
• Material: Case: Diecast steelCover: 316 grade stainless steel
• Glass thickness: 10 - 12 mm• Max. door weight: 80 kg• Max. door leaf width: 1100 mm• Installation: Clamp fixing, concealed, with hexagon
socket screws
Supplied with1 Top patch fitting for double action doors3 Allen keys SW2, 3 and 51 Glass cut-out detail
Finish Cat. No.
Satin 981.00.310Polished 981.00.311
Packing: 1 piece
Supplied with1 Bottom patch fitting for double action doors3 Allen keys SW2, 3 and 51 Glass cut-out detail
162
51
36
161146
68
37R55
Ø 20
R80
A
58
B StarTec Top patch fitting
Glass Panel FittingsPatch Fittings for Gates
Updated 04.09
Dim
ensi
ons
in m
mD
imen
sion
al d
ata
not b
indi
ng. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
www.hafele.com
Gla
ss P
anel
Fit
ting
s
SB 2009 HAA8
9
Door ControlsFloor Springs for Gates
• Area of application: For single action doors• Features: Removable spindle• Closing force: Size 2/3/4 complying with EN 1154• Max. door opening angle: Approx. 130º• Material: Cover plate:
304 grade stainless steel • Finish: Cover plate: Satin
Cat. No.
DCL 43 Non Hold-openEN2 932.84.037EN3 932.84.034EN4 932.84.038
Packing: 1 set
52-58
Supplied withFloor springCover plateFixing materialInstallation instructions
DCL 43EN 2/3/4
Floor spring cover plateSS 316
Closing Force Max. door leaf widthmm
Max. door leafweight kg
EN 2 850 70 EN 3 950 105 EN 4 1100 150
Finish Cat. No.
Satin 932.84.920Polished 932.84.921
• Material: Stainless steel 316
Packing: 1 piece
Updated 04.09
Dim
ensi
ons
in m
mD
imen
sion
al d
ata
not b
indi
ng. W
e re
serv
e th
e rig
ht to
alte
r sp
ecifi
catio
ns w
ithou
t not
ice.
www.hafele.com
Gla
ss P
anel
Fit
ting
s
SB 2009 HAA 9
9
Extended spindle For DCL 43
5 + L
Ø25
Length (L) mm Cat. No.
5 932.84.91110 932.84.91215 932.84.91320 932.84.91425 932.84.915
• Area of application: To increase the floor clearance (i.e. fordoors with thresholds or pool gates)
• Features: With radial serrations
Sealing compound
Packing: 1 set (2 cans)
Cat. No.932.00.310
• Area of application: For filling the cavities of a floor spring.Consisting of parent solution and hardener(2 cans)
• Total contents: 0.76 kg
Packing: 1 piece
Door ControlsFloor Spring Accessories
HÄFELE AUSTRALIA PTY. LTD.
STATE OFFICES
Victoria - Head Office - 8 Monterey Road,
(P.O. Box 1066) Dandenong VIC 3175
Telephone: (03) 9212 2000
Fax: (03) 9212 2001
E-mail: [email protected]
New South Wales
10 Forsyth Close, Wetherill Park NSW 2164
Telephone: (02) 8788 2200
Fax: (02) 8788 2201
E-mail: [email protected]
Queensland
12 Selhurst Street, Coopers Plains QLD 4108
Telephone: (07) 3344 1533
Fax: (07) 3344 1770
E-mail: [email protected]
Western Australia/N.T
29-33 Juna Drive, Malaga WA 6090
Telephone: (08) 9249 3833
Fax: (08) 9249 3328
E-mail: [email protected]
South Australia
21 Chesser Street, Adelaide SA 5000
Telephone: (08) 8232 9933
Fax: (08) 8232 9977
E-mail: [email protected]
Australian Capital Territory
1/88 Newcastle Street, Fyshwick ACT 2609
Telephone: (02) 6283 8400
Fax: (02) 6295 9211
E-mail: [email protected]
Tasmania
262 York Street, Launceston TAS 7250
Telephone: (03) 6331 7106
Fax: (03) 6334 6414
E-mail: [email protected]
Freecall 1800 806 307 for all
customers in country regions.
DESIGN CENTRES
Melbourne Design Centre
Lvl 1, 75-77 Flinders Lane, Melbourne VIC 3000
Telephone: (03) 9212 2000
Fax: (03) 9652 3701
E-mail: [email protected]
Sydney Design Centre
New Premises Open Mid 2009
Telephone: (02) 8788 2200
Fax: (02) 8788 2201
E-mail: [email protected]
Newcastle Design Centre
Unit 1, 47 Bolton Street, Newcastle NSW 2300
Telephone: (02) 8788 2200
Fax: (02) 4921 0901
E-mail: [email protected]
Brisbane Design Centre
1 Breakfast Creek Road, Newstead QLD 4006
Telephone: (07) 3344 1533
Fax: (07) 3253 3701
E-mail: [email protected]
Hobart Design Centre
309 Liverpool Street, Hobart TAS 7000
Telephone: (03) 6331 7106
Fax: (03) 6334 6414
E-mail: [email protected]
HÄFELE NEW ZEALAND LTD.
STATE OFFICES
Auckland - Head Office
16 Accent Drive,
East Tamaki, Auckland
Telephone: (09) 274 2040
Fax: (09) 274 2041
E-mail: [email protected]
Freephone 0800 4 HAFELE
Lower North Island Office
The Wool Store, Level 1
262 Thorndon Quay, Wellington
Telephone: (04) 472 0294
Fax: (04) 472 0295
E-mail: [email protected]
South Island Office
5 Wigram Close
Sockburn, Christchurch
Telephone: (03) 343 8200
Fax: (03) 343 8201
E-mail: [email protected]
DESIGN CENTRE
Auckland Design Centre
62 Cook Street
Auckland City, Auckland
Telephone: (09) 274 2530
Fax: (09) 274 2531
E-mail: [email protected]
www.hafele.comThis catalogue is for the use of the recipient only. It remains in all respects the property of Häfele. Reproduction of this brochure in whole or in part, or the reproduction of the illustrations as well as the copying of the layout,is strictly prohibited. All measurements given in this publication are not binding. Rights for design improvements reserved. No responsibility for typographical or other errors occurring in the catalogue production. All deliveriesmade corresponding to Häfele sales conditions. Häfele reserves the right to adjust prices as may be deemed necessary.
2009. Copyright by Häfele. All rights reserved. Printed in Australia. 01.2009 _ 732.SB.CAT