MUSTANG PROJECT STEP 1: Remove and Prepare Housings: Microprocessor 1) Remove the right and left housings being careful to remove the lamp sockets from there holes. You will not re- move the wiring har- ness or cut any wires. 2) Pop the lens from each hosing. Metal clips hold the lens on with friction. Simply pry the lens from the housing being careful not to damage the lens or housing. 3) Using the template be- low drill 5 holes. 4 of the holes are 1/8 inch with one larger 1/2 inch hole. Be sure and posi- tion the template so that the larges hole is next to the large reflector or the outside of the hous- ing. 4) Mount the LED panels ensuring that the three lead wires pass through the 1/2 inch hole. See white arrow. Use the included #4 washers and nuts to secure the board assembly from the back of the housing. Red with white- stripe Green Green Black Red with White Stripe Black STEP 2: Attach wire tap connectors: 1) You will attach three wire-tap connectors of each side of the rear of the car. 2) First attach a wire tap connector to the black wire exiting the turn signal lamp socket ( amber light). Attach one on each side of the of the car. 3) Second attach a wire tap connector to the ORANGE/LT BLUE stripe wire on the turn signal lamp socket on the right hand side of the car. Attach a wire tap connec- tor to the LT GREEN/ORANGE stripe on the turn signal lamp socked on the left hand side of the car. Remember the left hand side of the car is always the driver’s side for US cars. 4) Thirdly attach a wire tap connector to the BROWN wire on the BRAKE light socket. The wire color is the same for both sides of the car. Summary: You will now have 6 wire tap connectors attached to the rear wiring har- ness (three on each side) as follows: Right side: • Black wire of turn signal light. • ORANGE/LT BLUE stripe wire on turn signal light. • Brown wire of brake light. Left side: • Black wire of turn signal light. • LT GREEN/ORANGE wire on turn signal light. • Brown wire of brake light. ORANGE/BLUE Hole Template MP-6077-FB LED Se- quential Taillight Kit Fox Body Instructions
2
Embed
Fox Body LED Kit - Mustang Project Fox Body LED... · 2010. 5. 31. · quential Taillight Kit Fox Body Instructions. MUSTANG PROJECT Simply connect each wire from each lamp housing
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
MUSTANG PROJECT
STEP 1: Remove and Prepare Housings:
Microprocessor
1) Remove the right and
left housings being
careful to remove the
lamp sockets from there
holes. You will not re-
move the wiring har-
ness or cut any wires.
2) Pop the lens from each
hosing. Metal clips
hold the lens on with
friction. Simply pry the
lens from the housing
being careful not to
damage the lens or
housing.
3) Using the template be-
low drill 5 holes. 4 of
the holes are 1/8 inch
with one larger 1/2 inch
hole. Be sure and posi-
tion the template so that
the larges hole is next
to the large reflector or
the outside of the hous-
ing.
4) Mount the LED panels
ensuring that the three
lead wires pass through
the 1/2 inch hole. See
white arrow. Use the
included #4 washers
and nuts to secure the
board assembly from
the back of the housing.
Red with
white-
stripe
Green Green
Black
Red with
White Stripe
Black
STEP 2: Attach wire tap connectors:
1) You will attach three wire-tap connectors
of each side of the rear of the car.
2) First attach a wire tap connector to the
black wire exiting the turn signal lamp
socket ( amber light). Attach one on
each side of the of the car.
3) Second attach a wire tap connector to the
ORANGE/LT BLUE stripe wire on the turn
signal lamp socket on the right hand
side of the car. Attach a wire tap connec-
tor to the LT GREEN/ORANGE stripe on
the turn signal lamp socked on the left
hand side of the car. Remember the left
hand side of the car is always the driver’s
side for US cars.
4) Thirdly attach a wire tap connector to
the BROWN wire on the BRAKE light
socket. The wire color is the same for
both sides of the car.
Summary: You will now have 6 wire tap
connectors attached to the rear wiring har-
ness (three on each side) as follows:
Right side:
• Black wire of turn signal light.
• ORANGE/LT BLUE stripe wire on turn
signal light.
• Brown wire of brake light.
Left side:
• Black wire of turn signal light.
• LT GREEN/ORANGE wire on turn signal
light.
• Brown wire of brake light.
ORANGE/BLUE
Hole Template
MP-6077-FB LED Se-quential Taillight Kit Fox
Body Instructions
MUSTANG PROJECT
Simply connect each wire from each
lamp housing as follows:
Right side module/housing:
1) Connect the green wire to the wire
tap connector you placed on the
ORANGE/LT BLUE wire.
2) Connect the red wire to the wire tap
connector you place on the BROWN
wire.
3) Connect the black wire to the wire
tap connector you placed on the
black wire.
MUSTANG PROJECT
Step 3: Connect LED Modules
Right Side Lamp Housing
Left Side Lamp Housing
GREEN
GREEN
BLACK
BLACK
RED
RED
Left side module/housing:
1) Connect the green wire to the
wire tap connector you placed
on the ORANGE/LT BLUE wire.
2) Connect the red wire to the
wire tap connector you place on
the BROWN wire.
3) Connect the black wire to the
wire tap connector you placed
on the black wire.
Be sure and wrap each connector in
electrical tape before final installation
of the flasher module.
RED
GREEN
First we will remove the old
original flasher module. The
original flasher module will
be located on the driver side
of the car near the fire wall as
shown on the following pic-
ture.
The installation procedure is
as follows:
1) Remove the existing
flasher module
2) Connect the new flasher
wires red and greed to
the Mustang’s wiring pre-
viously removed.
3) Connect the black
“ground” wire from the
new LED flasher module
to a good chassis ground-
ing point.
Simply unsnap the cylinder
shaped module and remove
the push on connectors.
These will be attached with a
light blue and a purple/
orange stripe wire.
The Mustang Project LED
flasher module has three
color coded wire leads. Red,
Green, and Black.
Once you remove the old
module install the new LED
flasher module by simply
plugging in the red wire to
the Mustang’s Purple/
Orange stripe wire and the
green wire to the Mustang’s
Light blue wire.
You now have only to attach
the black wire to a convenient
chassis ground point.
A likely place to connect the
black ground wire will be
under a mounting screw on
the dash or on any metal part
screwed under the dash.
Just make sure that there is a
good electrical connection
between the black wire and
the cars chassis.
Light Blue Purple/Orange
stripe
Step 4: Install Flasher Module Test the taillights BEFORE