Dart Sweepforward Wing Manual Specifications Data : Configura�on: Wingspan: 635mm(25in) Motor: 2006-2400KV Length: 406mm(16in) ESC: 30A w/BEC 1A Flying Weight: 350g Battery: 3S 1300~1800mAh Flying Time: 5-8 Minutes Servo: 4.3g*2pcs Digital Material: Lightweight EPP Propeller: 6x3 Safety Attentions 2. Do not fly near HV power cable, signal sta�on, signal tower or Wi-Fi hot spot, to avoid signal interference. 3. Do not fly around no-fly zone according to local law. 1. Do not fly in raining, snowing, or windy weather. Diagram for ZOHD Flight Stabiliza�on Unit CG Marked in the bottom of Dart Wing Make sure to balance the CG before flying About CG Notes Throttle Calibration 1. 2. 3. 4. Shutdown all the mixes on your radio before using this Flight Stabili zation Unit. Don't trim any channel while flying. The red LED indicator means 3-axis stabili zation mode for advanced users. The blue indicator means 6-axis auto-stability / take-off mode for beginners. Stabili zation mode can be changed during flight by a 2 position switch on your radio. When calibrating the Flight Stabili zation Unit, both, red and blue LED indicators will flash quickly. Don't move the plane while doing this process. The calibration will be finished after both LED's are flashing quickly for about 5 seconds. Slow flashing means there was an error. Please try again. This Flight Stabilization Unit is compatible with S.BUS/PPM & Spektrum DSM2 receiver. For a proper performance, you should calibrate the ESC (throttle range) of this plane before you fly it for the fist time or change your radio. ESC Calibration Steps: Turn on the radio and move your throttle stick to the top position. Power ON the ESC After you hear two short beeps, lower the throttle stick back to the lowest position. The calibration will be finished after you hear two long beeps. INPUTS Input 1 Thr Thr Weight 100% Input 2 Ail Ail Weight 100% Input 3 Ele Ele Weight 100% Input 4 Rud Rud Weight 100% MIXER CH1 Thr Thr Weight +100% CH2 Left Servo Ail -50% No Expo Ele -70% No Expo CH3 Right Servo Ail -50% No Expo Ele 70% No Expo Radio Mixer Sets for be�er flight experience! The following parameters are tested and illustrated on condi�on of Frsky Taranis X9D+ w/ X8R, users may adjust a li�le according to your radio transmi�er and receiver. These mixer parameters can be applied either through Flight Stabiliza�on Unit, or straight to your servos.
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Dart Sweepforward Wing Manual
SpecificationsData : Configura�on: Wingspan: 635mm(25in) Motor: 2006-2400KV Length: 406mm(16in) ESC: 30A w/BEC 1A Flying Weight: 350g Battery: 3S 1300~1800mAh Flying Time: 5-8 Minutes Servo: 4.3g*2pcs Digital Material: Lightweight EPP Propeller: 6x3 Safety Attentions
2. Do not fly near HV power cable, signal sta�on, signal tower or Wi-Fi hot spot, to avoid signal interference.3. Do not fly around no-fly zone according to local law.
1. Do not fly in raining, snowing, or windy weather.
Diagram for ZOHD Flight Stabiliza�on Unit
CG Marked in the bottom of Dart WingMake sure to balance the CG before flying
About CG
Notes Throttle Calibration
1. 2. 3. 4.
Shutdown all the mixes on your radio before using this Flight Stabilization Unit.Don't trim any channel while flying.The red LED indicator means 3-axis stabilization mode for advanced users.The blue indicator means 6-axis auto-stability / take-off mode for beginners.Stabilization mode can be changed during flight by a 2 position switch on your radio.When calibrating the Flight Stabilization Unit, both, red and blue LED indicators will flash quickly. Don't move the plane while doing this process. The calibration will be finished after both LED's are flashing quickly for about 5 seconds. Slow flashing means there was an error. Please try again.This Flight Stabilization Unit is compatible with S.BUS/PPM & Spektrum DSM2 receiver.
For a proper performance, you should calibrate the ESC (throttle range) of this plane before you fly it for the fist time or change your radio.
ESC Calibration Steps:
Turn on the radio and move your throttle stick to the top position.Power ON the ESCAfter you hear two short beeps, lower the throttle stick back to the lowest position.The calibration will be finished after you hear two long beeps.
INPUTS
Input 1 Thr Thr Weight 100%
Input 2 Ail Ail Weight 100%
Input 3 Ele Ele Weight 100%
Input 4 Rud Rud Weight 100%
MIXER
CH1 Thr Thr Weight +100%
CH2 Left Servo Ail -50% No Expo
Ele -70% No Expo
CH3 Right Servo Ail -50% No Expo
Ele 70% No Expo
Radio Mixer Sets for be�er flight experience! The following parametersare tested and illustrated on condi�on of Frsky Taranis X9D+ w/ X8R, users may adjust a li�le according to your radio transmi�er and receiver. These mixer parameters can be applied either through Flight Stabiliza�on Unit, or straight to your servos.
Related Documents
