Flexible claw couplings ELKU-N KWN 22013 Couplings from Dresden / Germany By specialists – for specialists řemeny, převody a lineární technika
Flexible claw couplings ELKU-N
KWN 22013
Flexible claw couplings ELKU-N
KWN 22013
Couplings from Dresden / GermanyBy specialists – for specialists
řemeny, převody a lineární technika
general information 2
technical features
The flexible claw coupling N (ELKU-N) is a positive-locking, tor-sionally, flexible coupling which allows radial, axial and angular displacement between the driving and the driven shafts. It is slip proof. Torque is transmitted through the flexible buffer set into the po-ckets of the flexible buffer section which is distributed evenly over the circumference of the coupling. The claws on the guide ring or claw section grip into the buffer gaps. The buffers are subjected to compression from which results slight wear and high loading capacity.
The high damping of the coupling protects the drive from excessive dynamic overloading. The progressively rising spring charcteristic al-lows a rapid reduction in energy oscillations and limits their amplitude. Perfect operation can be guaranteed at a working temperature of -30 °C to +80 °C. The standard design is in grey cast iron EN-GJL-250-DIN EN 1561.
claw ring buffer part
hub
Technical changes for the purpose of progress are reserved. The design may differ from pictorial representation; dimensions have to be complying with given ones.
II 2 G llB T5 -20 °C ≤ Ta ≤ 50 °C
ll 2 D 90 °C -20 °C ≤ Ta ≤ 50 °C
we also offer special models:
• design with spacer• design with brake disc or brake drum• design with radially removable brake disk• design for vertical fitting• design for explosive surroundings
• design of claw couplings according to KWN 22003• other designs on request
calculation example:
Coupling ELKU-N searched for steady drive.
Driving machine: AC motor type 315 L - 200 kW -1 485 rpm, shaft diameter 80 mm
quantity Z = 40 per hour - ambient temperature ϑ = +40 °C starting torque T
AS ≈ 2T
AN = 2 574 Nm
Working machine: centrifugal pump with a relatively low mass inertia average load torque T
LN= 1 150 Nm
impact of the rated torque T
KN ≥ T
LN • S
ϑ= 1 150 Nm • 1,2 = 1 380 Nm
according to the rated torque is the ELKU-N coupling size 250 in question for T
KN= 2 500 Nm and T
Kmax= 5 000 Nm.
Check for TKmax factors:
starting factor: SZ= 1
temperature factor: Sϑ= 1,2
impact factor: SA= 1,5
TKmax
≥ TAS
• SZ • S
ϑ • S
A = 2574 Nm • 1 • 1,2 • 1,5 = 4 633 Nm
With this example, a coupling selection is simplified by Bill passa-ge represented. It is recommended that a coupling selection by the trained personnel of KWD leave to carry.
technical features3
The variety of types
Type A three parts design
Type B in two parts design
Type S1 design with brake disk
Type S2 design with radial dismountable brake disk
Type H design with spacer
SAor S
L
1,5
1,8
2,2
slight impacts
medium impects
high impacts
impact factor SAor S
L
number of starts per hour
number of starts per hour
SZ
over 800 starts per hour please request
temperature factor Sϑ
1,2
+60
+80
numerical values for perbunan
Sϑ
°C von
bis
1
-30
+30
1
-30
+40
1
-40
+60
Recommended values for influence factorsTable 1
100
1,0
200
1,2
400
1,4
starting factor SZ
800
1,6
TAN
= 9 550 • = 9 550 • = 1 287 [Nm]P
AN
nAN
2001 485
TAN
: installation torque [Nm]
TKN
: coupling torque [Nm]
TLN
: load torque [Nm]
TKmax
: max. coupling torque [Nm]
PAN
: power [kW]
nAN
: input speed [rpm]
Z : starting frequency
ϑ : ambient temperature [°C]
type A 4
Ordering example: ELKU-N A 16 - 47 H7 (x28) - 12v4) (x40)3) KWN 22013
Designation of a flexible claw coupling N type A, nominal size 16, finished bore d4 = 47 mm, tolerance zone H7,
without keyway in the shortened buffer part (hub length l2 = 28 mm) (for clamping unit) and pilot bore d
5 = 12 mm
(with hub length l3 = 40 mm).
16254063
100160200250400
500
630
1 000
1 250
1 600
2 500
3 1504 0005 0006 300
size pilotbore 2)
min min
-------
444747885988649878
11888
13498
138118128138138
14151822242838485560
10565
11570
12580
13590
150100155120130140140
48556065758590
100110100120110140120150130160145180150190200220240260
-------
305244885988649878
11888
13498
138118128138138
14151822242824325548
10565
11570
12580
13590
150100155120130140140
3845505865758595
105100120110140120150130160145180150190200220240260
110125140160180200225250280
315
350
400
440
480
520
560610660710
789098
108125140150165180165200180230200250215265240300250315320352384416
62758295
108122138155172165200180230200250215265240300250315320352384416
82102112122142162182203223
253
283
323
365
385
425
449489529589
40505560708090
100110
125
140
160
180
190
210
220240260290
40505560708090
100110
125
140
160
180
190
210
220240260290
131921212833384045
55
66
82
94
100
108
105119128152
202727324048525868
78
89
104
116
125
142
140152164188
Table 2main dimensions
max max
pilotbore 2)
d4
finishedbore 1)
d5
finishedbore 1)
d6
d14
d15
l1
l2
l3
l7
s1
222222233
3
3
3
5
5
5
6666
h9
l6
hub
buffer part claw ring
Footnotes see page 14.
5
torsionangle
ϕ [ ° ]
at TKN
16254063
100160200250400
500
630
1 000
1 250
1 600
2 500
3 1504 0005 0006 300
size speed
n[min-1] T
KN±T
KW
5 0005 0004 9004 2503 8003 4003 0002 7502 450
2 150
1 950
1 700
1 550
1 400
1 300
1 2001 1001 000
950
160250400630
1 0001 6002 0002 5004 000
5 000
6 300
10 000
12 500
16 000
25 000
31 50040 00050 00063 000
320500800
1 2602 0003 2004 0005 0008 000
10 000
12 600
20 000
25 000
32 000
50 000
63 00080 000
100 000126 000
4062
100160250400500625
1 000
1 250
1 575
2 500
3 125
4 000
6 250
7 3009 600
12 35015 600
454545454545454545
45
45
45
45
45
45
45454545
12,619,026,058,988,5
138,8236,0305,4404,3
618,6
893,7
1 245
1 693
2 122
2 812 3 6005 0006 8009 300
0,90,90,90,90,90,90,90,90,9
0,9
0,9
0,9
0,9
0,9
0,9
1,11,11,11,1
0,0020,0040,0070,0130,023
0,040,070,12
0,20,310,340,54
0,61,01,21,51,72,32,63,53,85,98,613
18,5
0,0020,0040,0070,0130,024
0,040,080,13
0,20,330,370,540,63
0,91,01,51,72,32,63,23,6
69,31420
1,52,53,34,76,99,513
17,5243132434563667982
100105130140180225290370
1,52,53,44,86,81014
19,5243234434759648085
100110120135185240320400
TKmax
torque[Nm]
dyn. torsionalstiffness
Cdyn
[ kNm/rad ]
rel.damping
Ψ
[ - ]
moment ofinertia
J [kgm2]
massm
[kg]
characteristic valuesTable 4
TKN
0,5 • Kmax
buffer part buffer partclaw ring
+ hubclaw ring
+ hub
5,88,8
11,927,140,663,8
108,4140,3185,8
284,2
410,4
572,5
777,6
973,9
1 292
1 5002 0702 8003 900
n [min-1]500
1 0001 5002 0002 5003 000
≥ 3 500n [min-1]
5001 0001 5002 0002 5003 000
≥ 3 500
1624
2
0,30,30,30,20,20,20,1
0,20,20,20,10,10,10,1
2524
2
0,30,30,30,20,20,20,1
0,20,20,10,10,10,10,1
4024
2
0,40,40,30,30,20,20,1
0,20,20,10,10,10,10,1
6326
4
0,40,40,30,20,20,20,1
0,20,20,10,10,10,10,1
10026
4
0,50,40,30,20,20,10,1
0,20,10,10,10,10,10,1
16026
4
0,50,40,30,20,20,2
-
0,20,10,10,10,10,1
20026
4
0,60,50,30,30,20,2
-
0,20,10,10,10,10,1
25038
5
0,70,50,30,20,2
--
0,20,10,10,10,1
40038
5
0,70,40,30,20,2
--
0,20,10,10,10,1
50038
5
0,80,40,30,2
0,20,10,10,1
63038
5
0,90,50,30,3
0,20,10,10,1
1 00038
5
10,50,30,2
0,10,10,10,1
1 2505
10
5
10,50,4
0,10,10,1
1 6005
10
5
10,50,3
0,10,10,1
2 5005
10
5
10,50,3
0,10,10,1
3 1506
12
6
1,20,8
0,120,08
4 0006
12
6
1,30,9
0,120,08
5 0006
12
6
1,41
0,12
6 3006
12
6
1,5
0,12
permissible shaft misalignment and alignment dimensionTable 3
radial displacementaxial displacement angular displacement
size dimension s
min [mm]
dimension smax
[mm]perm. axial displacementΔ K
a [mm]
perm. radial displacementΔ K
r [mm] at speed n
perm. angular displacementΔ K
w* [mm] at speed n
perm angular displacement Δ K
w [°] at speed n
type B 6
Ordering example: ELKU-N B 10 - 20 H7P14) (x35)3) - 16 H7P24) (x25) KWN 22013
Designation of a flexible claw coupling N type B, nominal size 10, finished bore d4 = 20 mm, tolerance zone H7, with keyway in
buffer part, (hub length l2 = 35 mm), finished bore d
5 = 16 mm, tolerance zone H7 and two keyways
(120° staggered) in the shortened claw part (with hub length l3 = 25 mm).
2,5
4
6,3
10
16
25
40
63
100
160
200
250
400
size pilotbore 2)
min min
-
-
-
-
-
-
-
-
-
-
-
44
47
8
8
10
11
14
15
18
22
24
28
38
48
55
19
24
32
42
48
55
60
65
75
85
90
100
110
8
8
10
11
14
15
18
22
24
28
38
48
55
-
-
50
68
78
90
98
108
125
140
150
165
180
24
28
38
42
48
55
60
65
75
85
90
100
110
58
68
80
95
110
125
140
160
180
200
225
250
280
-
-
50
68
78
90
98
108
125
140
150
165
180
40
46
62
70
80
90
98
108
125
140
150
165
180
42
42
62
72
82
102
112
122
142
162
182
203
223
20
20
30
35
40
50
55
60
70
80
90
100
110
20
20
30
35
40
50
55
60
70
80
90
100
110
-
-
9
11
13
19
21
21
28
33
38
40
45
12
12
20
24
26
33
35
40
50
56
72
82
90
Table 5main dimensions
max max
pilotbore 2)
d4
finishedbore 1)
d5
finishedbore 1)
d6
d14
d15
l1
l2
l3
l7
s1
2
2
2
2
2
2
2
2
2
2
2
3
3
h9
l6
buffer part
claw part
Footnotes see page 14.
7
torsionangle
ϕ [ ° ]
at TKN
2,5
4
6,3
10
16
25
40
63
100
160
200
250
400
speed
n[min-1] T
KN±T
KW
5000
5000
5000
5000
5000
5000
4900
4250
3800
3400
3000
2750
2450
25
40
63
100
160
250
400
630
1000
1600
2000
2500
4000
50
80
126
200
320
500
800
1260
2000
3200
4000
5000
8000
6
10
16
25
40
62
100
160
250
400
500
625
1000
45
45
45
45
45
45
45
45
45
45
45
45
45
2,3
3,6
5,4
8,3
12,6
19,0
26,0
58,9
88,5
138,8
236,0
305,4
404,3
0,9
0,9
0,9
0,9
0,9
0,9
0,9
0,9
0,9
0,9
0,9
0,9
0,9
0,0001
0,0002
0,0004
0,0009
0,002
0,004
0,007
0,013
0,023
0,04
0,07
0,12
0,2
0,0001
0,0001
0,0004
0,0008
0,002
0,004
0,007
0,012
0,022
0,04
0,065
0,11
0,17
0,2
0,3
0,6
0,9
1,5
2,5
3,3
4,7
6,9
9,5
13
17,5
24
0,2
0,3
0,7
1,1
1,6
2,6
3,6
4,7
7,1
10,5
11,5
16,5
21
TKmax
torque[Nm]
dyn. torsionalstiffness
Cdyn
[ kNm/rad ]
rel.damping
Ψ
[ - ]
moment ofinertia
J [kgm2]
massm
[kg]
characteristic valuesTable 7
TKN
0,5 • Kmax
buffer part buffer partclaw part claw part
0,9
1,6
2,5
3,8
5,8
8,8
11,9
27,1
40,6
63,8
108,4
140,3
185,8
size
radial displacementaxial displacement angular displacement
n [min-1]500
1 0001 5002 0002 5003 000
≥ 3 500n [min-1]
5001 0001 5002 0002 5003 000
≥ 3 500
2,524
2
0,20,20,20,20,20,20,1
0,20,20,20,20,20,20,1
424
2
0,20,20,20,20,20,20,1
0,20,20,20,20,20,10,1
6,324
2
0,20,20,20,20,20,20,1
0,20,20,20,20,20,20,1
1024
2
0,30,30,30,30,20,20,1
0,20,20,20,20,10,10,1
2524
2
0,30,30,30,20,20,20,1
0,20,20,10,10,10,10,1
4024
2
0,40,40,30,30,20,20,1
0,20,20,10,10,10,10,1
6326
4
0,40,40,30,20,20,20,1
0,20,20,10,10,10,10,1
10026
4
0,50,40,30,20,20,10,1
0,20,10,10,10,10,10,1
16026
4
0,50,40,30,20,20,2
0,20,10,10,10,10,1
20026
4
0,60,50,30,30,20,2
0,20,10,10,10,10,1
25038
5
0,70,50,30,20,2
0,20,10,10,10,1
40038
5
0,70,40,30,20,2
0,20,10,10,10,1
permissible shaft misalignment and alignment dimensionTable 6
size dimension s
min [mm]
dimension smax
[mm]perm. axial displacementΔ K
a [mm]
perm. radial displacementΔ K
r [mm] at speed n
perm. angular displacementΔ K
w* [mm] at speed n
perm angular displacement Δ K
w [°] at speed n
1624
2
0,30,30,30,20,20,20,1
0,20,20,20,10,10,10,1
Ordering example: ELKU-N S1 25 - 315 - 50 H7P14) (x50)3) - 13v4) (x50)3) KWN 22013
Designation of a flexible claw coupling N type S1, nominal size 25 with brake disk d2 = 315 mm, finished bore
d4 = 50 mm, tolerance zone H7, with keyway, (hub length l
2 = 50 mm), pilot bore d
5 = 13 mm, (hub length l
3 = 50 mm).
type S1 8
254063
100160200250400
500
630
1 000
1 250
1 600
2 5002 5003 1504 0005 0006 300
size pilotbore 2)
min min
------
305244885988649878
11888
13498
138118128138138
151822242838485560
10565
11070
12580
12590
140100145110120130130
555565707575
100105100120105135120135120135135175140180190210230250
151822242824325548
10565
11570
12580
13590
14590
155120130140140
45506065758595
105100120110140120150130160145180150190200220240260
125140160180200225250280315315350350400400440440480480520520560610660710
8585
105115120120160170160195170220195220195220220280230295300332364396
758298
108122138155172165200180230200250215265240300250315320352384416
161618182020203030303030303030303030303030303030
102112122142162182203223253253283283323323365365385385425425449489529589
505560708090
100110125125140140160160180180190190210210220240260290
505560708090
100110125125140140160160180180190190210210220240260290
19212128333840455555666682829494
100100108108105119128152
max max
d4
finishedbore 1)
d5
finishedbore 1)
d6
d14
d15
l1
l2
l3
l7
s1
272732404852586878788989
104104116116125125142142140152164188
h9
l6
315315355400450450500630560710630800710800710800
1 0001 1201 0001 1201 0001 2501 2501 250
b1
d2
222222333333335555556666
Table 8main dimensions
brak
e tor
que d
ynam
ically
brak
e tor
que s
tatic
ally
brake disk
buffer part claw ring
hub
Footnotes see page 14.
special designs9
ELKU-N P: flexible claw coupling with brake drum
torsionangle
ϕ [ ° ]
at TKN
254063
100160200250400
500
630
1000
1250
1600
2 5002 5003 1504 0005 0006 300
size speed
n[min-1] T
KN±T
KW
4 8004 8004 2503 8003 4003 0002 7502 4002 1502 1501 9501 9001 7001 7001 5501 5501 4001 3501 3001 2001 2001 1001 000
950
250400630
1 0001 6002 0002 5004 0005 0005 0006 3006 300
10 00010 00012 50012 50016 00016 00025 00025 00031 50040 00050 00063 000
500800
1 2602 0003 2004 0005 0008 000
10 00010 00012 60012 60020 00020 00025 00025 00032 00032 00050 00050 00063 00040 000
100 000126 000
62100160250400500625
1 0001 2501 2501 5751 5752 5002 5003 1253 1254 0004 0006 2506 2507 3009 600
12 35015 600
4,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,5 4,54,54,54,54,54,5
19,026,058,988,5
138,8236,0305,4404,3618,6618,6893,7893,71 2451 2451 6931 6932 1222 1222 8122 8123 6005 0006 8009 300
0,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,91,11,11,11,1
0,1240,1270,2310,3740,664
0,691,073,822,566,184,169,996,8310,58,2910,925,338,626,540,128,964,669,074,5
0,0040,0070,0130,024
0,040,080,13
0,20,330,370,540,63
0,91,01.51.72.32.63,23,66,09,3
14,020,0
11,412,017,322,731,534,144,791,083,7
117,5109,5152,5148,2168,3160,4178,8270,0315,3300,0355,0350,0490,0555,0635,0
2,53,44,86,81014
19,5243234434759648085
100110120135185240320400
TKmax
torque[Nm]
dyn. torsionalstiffness
Cdyn
[ kNm/rad ]
rel.damping
Ψ
[ - ]
moment ofinertia
J [kgm2]
massm
[kg]
characteristic valuesTable 9
TKN
0,5 • Kmax
claw ring+ hub
claw ring+ hub
8,811,927,140,663,8
108,4140,3185,8284,2284,2410,4410,4572,5572,5777,6777,6973,9973,91 2921 2921 5002 0702 8003 900
bufferpart +brake disk
bufferpart +brake disk
claw ring
hub
brake drum
buffer part
hub 1
hub 2 claw ring
buffer part
type S2 10
Ordering example: ELKU-N S2 25 - 315x30 - 50 H7P14) (x50)3) - 13v4) (x50)3) KWN 22013
Designation of a flexible claw coupling N type S2, nominal size 25 with brake disk d2 = 315 mm, b
1 = 30 mm,
finished bore d4 = 50 mm, tolerance zone H7, with keyway, (hub length l
2 = 50 mm), pilot bore d
5 = 13 mm, (hub length l
3 = 50 mm).
254063
100160200250400
500
630
size
min
151822242824325548
10565
115
45506065758595
105100120110140
125140160180200225250280315315350350
315315315355400450500560630630710710
303030303030303030303030
222260270283328343402417437452456456
556065758590
100110120120140140
138168167167197197236236236236236236
334444666666
max max
d4
finishedbore 1)
d5
finishedbore 1)
d6
d2
l1
l2
s1
h9
l6
110140140140170170210210210210210210
b1
l3
505560708090
100110125125140140
Table 10main dimensions
ELKU-N S2: flexible claw coupling with brake disc, five parts
brake disk
Footnotes see page 14.
special designs11
ELKU-N S2: flexible claw coupling as connecting coupling for hydrodynamically coupling TK-N S
torsionangle
ϕ [ ° ]
at TKN
254063
100160200250400
500
500
630
630
size speed
n[min-1] T
KN±T
KW
3 4002 7502 7502 1502 1501 7001 4001 1001 1001 100 950
9501 1001 100
950950
250400630
1 0001 6002 0002 5004 0005 0005 0005 0005 0006 3006 3006 3006 300
500800
1 2602 0003 2004 0005 0008 000
10 00010 00010 00010 00012 60012 60012 60012 600
62100160250400500625
1 0001 2501 2501 2501 2501 5751 5751 5751 575
4,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,5
19,026,058,988,5
138,8236,0305,4404,3618,6618,6618,6618,6893,7893,7893,7893,7
0,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,9
0,20,250,26
0,40,68
1,11,652,75
4,24,2
4,254,25
7,27,27,37,3
0,0040,0070,0130,024
0,040,080,13
0,20,330,370,330,370,540,630,540,63
2226,529,5
35536383
117138138145145195195205205
2,53,44,86,81014
19,5243234323443474347
TKmax
torque[Nm]
dyn. torsionalstiffness
Cdyn
[ kNm/rad ]
rel.damping
Ψ
[ - ]
moment ofinertia
J [kgm2]
massm
[kg]
characteristic valuesTable 11
TKN
0,5 • Kmax
claw ring+ hub
claw ring+ hub
8,811,927,140,663,8
108,4140,3185,8284,2284,2284,2284,2410,4410,4410,4410,4
bufferpart +BS + hub
bufferpart +BS + hub
claw ring spacer hub
buffer part
type H 12
size
min max
pilotbore 2)
d4
finishedbore 1)
d6
d14
l1
l2
s2
h9
l8
d16
min max
d5
finishedbore 1)
d15
l3
s3
Table 12main dimensions
6,36,31010161616252525252540404040406363636363
100100100100160160160160200200200200250250250
----------------------------------
444444
10101111141414151515151518181818182222222222244224242828283838382838484848
32324242484848555555555560606060606565656565757575758585858590909090
100100100
10101111141414151515151518181818182222222222242424242828282838383838484848
32324242484848555555555560606060606565656565757575758585858590909090
100100100
80809595
110110110125125125125125140140140140140160160160160160180180180180200200200200225225225225250250250
5050686878787890909090909898989898
108108108108108125125125125140140140140150150150150165165165
5050707080808090909090909898989898
108108108108108125125125125140140140140150150150150165165165
5151636373737385858585859191919191
111111111111111131131131131144144144144169169169169185185185
175215180220190230280200240290320380220260300320385230270310330390290330350400310350370420370390440470390410460
30303535404040505050505055555555556060606060707070708080808090909090
100100100
454545455050605050607080656565658070707070808080808090909090
100100100100110110110
87127
87127
85125165
85125165185235
82122162182232
81,5121,5161,5181,5231,5121,5161,5181,5231,5118,5158,5178,5228,5158,5178,5228,5258,5152,5172,5222.5
555555555555555 5566666666666666666888
100140100140100140180100140180200250100140180200250100140180200250140180200250140180200250180200250280180200250
Ordering example: ELKU-N H 63 - 140 - 40 H7P14) (x60)3) - 20v4) (x70)3) KWN 22013
Designation of a flexible claw coupling N type H, nominal size 63 with spacer s3 = 140 mm, finished bore d
4 = 40 mm,
tolerance zone H7, with keyway, (hub length l2 = 60 mm), pilot bore d
5 = 20 mm, (hub length l
3 = 70 mm).
Footnotes see page 14.
size
special designs13
ELKU-N: flexible claw coupling with taper-lock-clamping unit
6,36,31010161616252525252540404040406363636363
100100100100160160160160200200200200250250250
5 0005 0005 0005 0005 0005 0005 0005 0005 0005 0005 0005 0004 9004 9004 9004 9004 9004 2504 2504 2504 2504 2503 8003 8003 8003 8003 4003 4003 4003 4003 0003 0003 0003 0002 7502 7502 750
6363
100100160160160250250250250250400400400400400630630630630630
1 0001 0001 0001 0001 6001 6001 6001 6002 0002 0002 0002 0002 5002 5002 500
126126200200320320320500500500500500800800800800800
1 2601 2601 2601 2601 2602 0002 0002 0002 0003 2003 2003 2003 2004 0004 0004 0004 0005 0005 0005 000
161625254040406262626262
100100100100100160160160160160250250250250400400400400500500500500625625625
4,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,5
5,45,48,38,3
12,612,612,619,019,019,019,019,026,026,026,026,026,058,958,958,958,958,988,588,588,588,5
138,8138,8138,8138,8236,0236,0236,0236,0305,4305,4305,4
2,52,53,83,85,85,85,88,88,88,88,88,8
11,911,911,911,911,927,127,127,127,127,140,640,640,640,663,863,863,863,8
108,4108,4108,4108,4140,3140,3140,3
0,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,90,9
87127
87127
85125165
85125165185235
82122162182232
81,5121,5161,5181,5231,5121,5161,5181,5231,5118,5158,5178,5228,5158,5178,5228,5258,5152,5172,5222,5
0,00040,00040,00090,0009
0,0020,0020,0020,0040,0040,0040,0040,0040,0070,0070,0070,0070,0070,0130,0130,0130,0130,0130,0230,0230,0230,023
0,040,040,040,040,070,070,070,070,12 0,12 0,12
0,00130,00140,00280,00310,00560,00600,00640,00990,01000,01100,01150,01200,01800,01900,02000,02100,02200,03000,03200,03400,03500,03700,05400,05800,06000,06500,09500,10000,10500,11000,16000,17000,18000,19000,27000,28000,3000
0,60,60,90,91,51,51,52,52,52,52,52,53,33,33,33,33,34,74,74,74,74,76,96,96,96,99,59,59,59,513131313
17,517,5 17,5
1,92
2,73
3,94,34,75,35,86,36,67,1
88,5
99,39,99,8
10,511,311,712,714,1
1515,516,519,720,821,422,6
2626,728,529,5
3637,2
39
torsionangle
ϕ [ ° ]
at TKN
speed
n[min-1] T
KN±T
KWT
Kmax
torque[Nm]
dyn. torsionalstiffness
Cdyn
[ kNm/rad ]
rel.damping
Ψ
[ - ]
moment ofinertia
J [kgm2]
massm
[kg]
characteristic valuesTable 13
TKN
0,5 • Kmax
claw ring +spacer+ hub
buffer partclaw ring +spacer+ hub
buffer part
l8
remarks 14
If orders do not specify the length of the hubis, we have been supplying prospectus.
Special designs are available on request:
• Available in cast iron EN-GJS-400-15U DIN EN 1563,• two keyways• with locking thread• finish bore without keyway (for clamping sets)• Versions with hole for removing the shaft• hard chromed brake disk
ELKU-N: flexible claw coupling in flange design
Hub bore
Abbreviation
pilot bored
v
without keyway
-
one keyway
P1
two keyways120° turned
P2
two keyways180° turned
P3
Tolerancefield H7
type of the hub bore Table 14
1) finished bore to ISO-fit H7, keyway to DIN 6885 sheet 1, fit JS 9 2) without keyway, pilot bore - untoleranced dimension, „average“ to DIN ISO 2768 3) see page 14 „remarks“ 4) see page 14 „type of hub bore“
remarks15
Materials
Hub, claw ring, claw body and buffer part: EN-GJL-250 DIN EN 1561
brake disk: EN 10025-2-S355J2+N / GS 30 DIN 1681
buffer: Perbunan 80 Shore A
spacer: EN-GJS-400-15U DIN EN 1563
alternative materials at the manufacturer‘s
Installation and operating conditions
The arrangement of the coupling parts to be connected to theShaft ends is desired.The given permitted misalignment values provide generalValues under the following conditions is:
• Load up to the rated torque• Operating speed n = 1 500 rpm (for n <1 500 min-1 is the maximum speed)• ambient temperature of +30 °C.• Maximum values in radial or angular misalignment
If both shifts at the same time, the values may onlybe used proportionately. In this case, please consultwith the manufacturer.
balancing condition
In general, the elastic claw couplings in unbalanced state deli-vered.After the user‘s requirements, they can dynamically the quality Q 6.3 (ISO Recommendation 1940) or static delivered balanced.
Size selection in accordance with DIN 740 Part 2
Size selection in accordance with DIN 740 Part 2 The design of the coupling is the laws of physics.
It is recommended that a coupling selection the trained personnel of KWD perform to leave.
roll screen with ELKU-N log washer drive with ELKU-N
Certified in accordance with ISO 9001: 2008Scope development, manufacture, sale and servicing of couplings in the drive technology field
Certified Welding Company / GSI SLV
Issue: 02/2013
Sídlo firmy a centrální sklad / Headquarters
TYMA CZ, s.r.o.
Na Pískách 731/12
CZ − 400 04 Trmice
Tel.: +420 475 655 010
Fax: +420 475 655 018
E−mail: [email protected]
http: www.tyma.cz
e−shop: belt-online.com